Transcript
I
MACHINE CODE : B20574
Model: IM250 II Part No. 900400 Impulse 16 Gauge Finish Nailer
MODEL IM250 F-16 II
I
IMPULSE FINISH NAILER
TOOL SCHEMATIC AND PARTS IMPORTANT! DO NOT DESTROY Always refer to operators manual #405606 for detailed information on this tool. It is the customers responsibility to have all operators and service personnel read and understand this information.
03 MODEL
MACHINE CODE : B20574 IM250 F-16 II 900400
88 1
86
19
19
Tighten to 40-45 IN. - LB.
23 20 93
8
Tighten to 20-25 IN. - LB.
67
68
22 59
93 55
69 50 70
9
35
97
66
59
71 Tighten to 20-25 IN. - LB.
36
78
61 12
53
12
30
87
10
62 89
41
46 25
31
Tighten to 8-10 IN. - LB.
32
31
95 96 32
33
Tighten to 15-20 IN. - LB.
51 34 94 90 Tighten to
3 IN. - LB.
58
52 Includes all these parts
Tighten to 25-30 IN. - LB.
63 57 64 4 65
92 56 91 65
54
To drive 1-1/4” or shorter nails
29-07-2009
03 MODEL MACHINE CODE : B20574 IM250 F-16 TYPE II, 900400
PARTS LEGEND 1 2 3 4 > 5 > 6 7 8 9 10 11 12 15 16 *17 18 19 20 21 22 23 25 30 31 ➔ 32 **33 34 35 36 ➔ 37 38 40 41 42 43 44 45 46 47 48 49 50 51 52
* ▲ ** ➔
900356 900455 901065 008388 900960 900969 006562 900271 900573 900468 900287 401356 403146 900004 404700 403167 900479 900280 404601 404490 900232 900968 900415 900405 900944 900496 900576 900312 900311 900943 900508 900453 900289 900903 403082 900942 401450 404385 402201 401395 900358 900336 900941 404702
1 1 4 1 1 3 3 1 1 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 3 1 1 1 2 1 2 1 1 1 1 2
Grille Filter Shoulder Screw, 10-24 x 1-1/4 Flat Washer #10 Cap Assembly Screw, Taptite, B-32 x 5/8 Washer #8 Circuit Board Assembly Fan Motor with Mount Washer Spark Plug Assembly Sleeve, Motor Stem Adapter (Yellow) Cylinder Head O-Ring Fan Blade Assembly Removable spark Plug Wire Spark Unit Assembly Head Switch Assembly Trigger Switch Assembly Cable Clamp Screw 10-32 x 5/8 Actuator Assembly Self Clenching Nut Handle Assembly, Right Warning label Nameplate Contact Positive Contact Negative Handle Assembly, Left International Label Thread Forming Screw, 8-16 x 7/8 Belt Hook Screw, 8-32 x 1 1/2 REMOVED Bushing (SILVER) Pad Light Pipe Screw, Phillips Head, 2-56 x 5/8 Spring Trigger Contact Wire Assembly Nut 8-32 Screw, Thread 6-32 x 3/8
53 54 55 56 57 58 ▲ 59 61 62 63 64 65 ▲ 66 67 68 69 70 71 72 73 74 *75 76 *77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97
900329 900328 900350 900301 900302 900166 900338 900332 900303 900326 900417 900900 004174 900335 900412 900342 900353 900324 403104 403100 403099 403098 403095 403094 900416 403084 403089 403090 403092 403091 404339 403106 900651 900323 900411 900352 900182 B20579A 403713 404613 900164 900331 900341 404922
1 1 1 1 1 1 2 1 1 2 1 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 2 1 1 1 2 1 3 1 1 2 2 2
Spring, Cover Spring, Negator Lever, Quick Clear Follower Cover Spring Screw 10-32 x 1/2 Hub Cover, Moveable Wear Strip Rail Assembly Socket Head Cap Screw 10-32 x 5/16 Screw 10-24 x 7/8 Spring, Quick Clear Nose Assembly Mounting Ring Pivot Pin Front Guide Air Dam Combustion Chamber Assembly Retaining Ring, Piston Piston Ring Piston Driver Blade Assembly Bumper Upper Probe Assembly Sleeve and Midcheck Ring Assembly Seal Washer Wave Washer Retaining Ring, Midcheck Muffler Spring, Chamber Return Cage Label, Logo Probe, Lower Housing Assembly Tip Washer, Trigger Back Plate Insert E-Ring, Retaining Cable Tie Ring Insert, Handle E-Ring Battery Pad
Denotes Normal Wear Item. Apply Loctite 242 (Blue) Part No.093500 Make sure Warning Label (900496) is properly affixed replace if necessary. Label is available at no charge through the Service Dept. Denotes Change
SAFETY INSTRUCTIONS 1. WEAR EYE AND EAR PROTECTION. 2. ALWAYS ASSUME THE TOOL IS ‘LOADED’. 3. OPERATE THE TOOL ONLY ON THE WORK SURFACE.
5. ALWAYS POINT THE TOOL AWAY FROM YOURSELF AND OTHERS WHEN CLEARING JAMS OR REMOVING FASTENERS. Pull the follower back and latch. Tip the tool nose up slightly and fasteners should slide out of the magazine. If fasteners are jammed, refer to the appropriate section of the operating manual.
4. NEVER REMOVE OR DISABLE THE WORK 6. NEVER ATTEMPT TO OPERATE THE IMPULSE TOOL CONTACTING ELEMENT. IF PARTS ARE LOOSE, DAMAGED OR MISSING. This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface. NEVER operate the tool if the work contacting element is not working properly.
29-07-2009
MACHINE CODE : B20574 IM250 F-16 II
ACCESSORIES Impulse Nailer Case Part No. 900488
Battery Cell Part No. B20544E
Impulse Oil
Part No. 401482
Lubricating Oil Aceite lubricante Specially formulated for all Impulse® Tools
Part No. B20544F
Formulado especialmente para todas las herramientas Impulse®
Torx Key For tightening fan blade to motor Part No. 900183
CAUTION
INDOOR USE ONLY
Battery Charger Kit (Replacement Transformer Only Part No. B20544C)
Part No. B20544B
ND NOSE PLATE TO SHOOT ND-BRADS
Degreaser Cleaner Ideal cleaner for all Paslode tools
Part No.B20579 For Impulse & Pneumatic Tools ®
NET CONTENT: 12 FLUID OUNCES (340 Grams) CONTEN IDO NETO: 12 ONZAS LIQUÍDAS (340 Gramos)
DANGER: EXT R E M N T E NT S U NDER PRELY FLAMMABLE, VAPOR HARMFUL, CAOCK PANEL E S S U R E , S E E O T H E R C A U TIO N S O N B ¡PELIGRO! EX T R E M AD A M E N TE O C I V O, C O N T E NI D O B A J O PRESIÓN, VER OTIRNFLAMABLE, VAPOERS ENN EL PANEL AL DORSO A S P R E C A U CI O N
Part No. B20544L
P Printed in U.S.A. © 2003, Illinois Tool Works , Inc.
An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061
405607-20 29-07-2009
