Transcript
Features > Pass-through 30-pin connector allows charge/sync. > Thin profile (only 0.515”). > Up to 150 ft range. > Supports iPod with 30 pin dock connector from 3rd Gen forward. > Replaceable Battery CR 2025.
CONGRATULATIONS ON YOUR PURCHASE OF THE iNAV-BOSS WIRELESS RF REMOTE CONTROL The Boss Remote with iNav Bottom Dock was designed to provide maximum control of your iPod/iPhones from anywhere you choose to place it regardless of whether it is in your backpack or over a hundred feet away in a different room connected to your home stereo. Its small size allows audio connection on newer iPod version.
iNav-Boss Operation
Optional iNAV Accessories Additional iNAV Remotes (Boss / Elite / Standard) Pair up to 7 remotes with any iNav receiver dock. Place a remote in each bedroom, out by pool or anywhere you choose to control your music.
Pairing Instructions Step 1 – Make sure your iPod/iTouch/iPhone is sufficiently charged. Step 2 – Detach iNav receiver from your iPod/iTouch/iPhone and wait 5 seconds. Step 3 – Reattach the iNAV receiver to the iPod/iTouch/iPhone dock connector. Step 4 – Within 30 seconds of Step 3, press and hold all four buttons simultaneously on the new remote for three seconds (Volume Up, Volume Down -, FF, RW) and release after 5 seconds. Step 5 – Wait approximately 5 seconds. The new remote has been paired with the iNav dock.
iPod RF receiver setup: (FIG 1) Plug the iNav dock into the 30 pin dock connector located on bottom of your iPod/iTouch/iPhone. Please WAIT 15 seconds for the automatic self-diagnostic to run. Plug in your ear buds or speakers or connect to your home stereo through a set of RCA jacks (supplied in the iNav-Boss kits). With iPhone/iTouch plug in headset after inserting the iNav dock and waiting 5 seconds. To sync or charge the iPod, simply plug your USB/Firewire or charging device into the bottom of the iNAV while it’s connected to the iPod/iTouch/iPhone.
NAVigation Mode
Advanced Low Power Mode (ALPM): The iNav uses an advanced power down mode, which minimizes current draw on your iPod/iPhone battery if you are not connected to a constant power source. After 2 hours of sensing no remote commands being sent, the iNav goes into a battery saving mode. The iNAV receiver will automatically repower itself when it detects music playing or a remote button being pressed for more than 0.6 seconds.
In Navigation Mode – To enter the NAVigation mode press the center button with the rectangle symbol. Now use the Volume up for moving up on an iPod menu, the volume down for moving down on an iPod menu. Use the pause to selecting an iPod menu item. Use the Rewind song to go back in the menu. The mode switch must be in the left position for NAVigation. The mode switch is the right position for Shuffle On/Off. Once the purpose of the switch is set and the case close it will be only usable for the purpose.
Boss Remote Control Functions Rewind/Fast Rewind: Press and release this button to move track BACKWARDS. Press and HOLD this button to rewind through the track Volume Down: Press and HOLD this button to turn down volume. Enter Nav Mode: Press this button once to place the remote in the Navigation mode. Nav the menus in the iPod when done press again to return to standard operational mode.
Forward/Fast Forward: Red LED on when transmitting Forward/Fast Forward: Press and release this button to move track FORWARD. Press and HOLD this button to forward through the track. Volume Up: Press and HOLD this button to turn down volume. Play/Pause/Sleep: Press and release to toggle between Pause and Play. Press and HOLD for 2 full seconds to put the iPod into sleep mode
iPod/iTouch/iPhone is a registered trademark of Apple Computer, Inc. All rights reserved.
Contact us via email:
[email protected] iNav-Boss (Navigator/Boss Manual Revision 1.0) Product Made In Taiwan
Technical Specifications Operating Range: Up to 150 ft. Transmission Method: Radio frequency Operating Frequency: 433.92 MHz Remote Power: (2) CR2025 3V Receiver Power: Powered from iPod with Advanced Low Power Mode (ALPM) Remote Dimensions/Weight: 2.275” x 1.65” x 0.515” / 0.8 oz Receiver Dimensions/Weight: 4.3” x 0.79” (w/o connector height) x 0.55” / 0.5 oz
Message Handling If either of these two message come up on the iPod/iToucd/iPhone display answer No. Then the MP3 unit will now response to remote commands If no audio on headset 1.) Power on the iTouch or iPhone. 2.) Plug the iNav dock into the iTouch or iPhone and wait 4 seconds. 3.) Then plug in the head set connection into the 3.5mm jack. Audio has now be rerouted.
