Infostation Rack-to-tower Conversion Kit

Transcript

IFS I & II Rack-to-Tower Conversion Kit 1 InfoStation Rack-to-Tower Conversion Kit NOTE: Information contained in this document applies to both the DXIFS-TKIT (Gray tower kit for the IFS I chassis) and S10A137 (Black tower kit for the IFS II chassis). This kit provides all the parts necessary to convert an existing rack mount InfoStation to a tower configuration. The kit includes the following items: 1 1 1 1 1 Top Cover Top Panel Base Left Side Panel Right Side Panel Base 2 6 6 2 5 Side Cover Brackets #10-32 Phillips Screws #6-32 Phillips Screws #6-32 Black Phillips Screws #6-32 Phillips Pan Head Screws InfoStation Chassis (Not Included) Left Cover Bracket Right Cover Bracket TKIT_09 Figure 1: Installation Overview Installation 1. Unplug the InfoStation and verify that all cables have been disconnected. 2. Place the InfoStation on a soft clean surface to protect the finish of the chassis. 3. Remove the two (2) screws securing each chassis handle to the InfoStation mounting flanges (Figure 2). D89-0000-0113 Rev. B00 StorCase Technology, Inc. 2 NOTE: IFS I & II Rack-to-Tower Conversion Kit Save handles! Handles will be needed if the chassis is ever reverted back to a rack mount configuration. Mounting Flange (Right Side) #6-32 Phillips Countersink Screw (2 per Handle) TKIT_01 Figure 3: Chassis Handle Removal 4. Once the handles are removed, attach the tower base to the chassis and secure with the six (6) #10-32 Phillips screws provided (Figure 3). The chassis will have to be turned upside-down in order to secure the base to the chassis (Figure 4). InfoStation I Chassis Flange (Insert into Slot) Slot Base TKIT_02 Figure 3: Base Installation StorCase Technology, Inc. D89-0000-0113 Rev. B00 IFS I & II Rack-to-Tower Conversion Kit 3 #10-32 Phillips Screw (6 Total) Base (Front) TKIT_03 Figure 4: Securing the Base to the Chassis 5. Once the base is secured, stand the chassis upright. Attach the top base panel and secure with the six (6) #6-32 Phillips screws provided (Figure 5). Top Cover Mounting Slot (6 Total) #6-32 Phillips Screw (6 Total) TKIT_04 Top Base Panel (Front) Figure 5: Top Base Panel Installation D89-0000-0113 Rev. B00 StorCase Technology, Inc. 4 6. IFS I & II Rack-to-Tower Conversion Kit Once the top base panel is attached, the top cover is ready to be installed. Make certain the bottom tabs on the cover are lined up with the mounting slots on the top base panel (Figure 4). Once installed, secure the cover with one (1) #6-32 Phillips Pan Hd. screw provided (Figure 6). #6-32 Phillips Pan Hd. Screw Top Cover Top Cover Top Base Panel TKIT_05 InfoStation I Chassis (Rear) Figure 6: Top Cover Installation 7. Attach the side cover brackets to both sides of the InfoStation chassis with four (4) #6-32 Phillips Pan Hd. screws provided (Figure 7). InfoStation Chassis Left Cover Bracket Right Cover Bracket TKIT_08 #6-32 Phillips Pan Hd. Screw (2 per Bracket) Figure 7: Attaching the Side Cover Brackets to the InfoStation Chassis StorCase Technology, Inc. D89-0000-0113 Rev. B00 IFS I & II Rack-to-Tower Conversion Kit 8. 5 Attach each side panel to the chassis by lining up the four (4) bottom slots on the panel with the four (4) tabs on the base. Once tabs are lined up, slide panel forward onto chassis (Figure 8). Secure each panel to the chassis with one (1) #6-32 black Phillips screw provided (Figure 9). Side Panel (Right Side) Slot Tab Base TKIT_06 Enlarged View Figure 8: Side Panel Installation D89-0000-0113 Rev. B00 StorCase Technology, Inc. 6 IFS I & II Rack-to-Tower Conversion Kit #6-32 Phillips Countersink Screw (1 per Side) TKIT_07 Figure 9: Securing the Side Panels to the Chassis StorCase Technology, Inc. D89-0000-0113 Rev. B00