Transcript
Quick guide
How to set up your new Opalum sound system
1
Opalum® STREAM series Owner's Guide Connecting the system
General notes_
Connect the active speakers to the Hub using the speaker cables included in the box or any 2 conductor speaker cable. Don´t worry about the polarity of the cables and terminals. The system operates at maximum performance in any case due to its digital nature. The cables transfer both signal and power, which is why you don´t need an extra power cable for each active speaker.
5. Connecting the system The System TheOpalum speakers ofSound the Opalum sound system can b thanks to the system. Actiline® technology. In both is aways pure digital Therefore useconnected digital(figure or 4) or • Parallel • cables Daisy chain 5) optical if connected possible(figure when connecting sources Both connection schemesto arethe presented below system. For maximum ease of use the polarity of the sp
The Two Styles of Connection – both equally good. – The Traditional: Connect each active speaker to the Hub using the speaker cables.
Digital sources
(Airport Express, Apple TV, computer, blueray, HTPC, dvd, TV, video games, etc)
Analog source
(mp3-player, bluetooth receiver, ect.)
Subwoofer
Power supply
Digital sources
(Airport Express, Apple TV, computer, blueray, HTPC, dvd, TV, video games, etc)
Analog source
(mp3-player, bluetooth receiver, ect.)
Subwoofer
Power supply
– The Speaker Chain: Connect just one active speaker to the Hub. Then connect the second speaker to the first speaker.
2
data is transferred to the speaker digitally – ano
For instructions on how to properly use the spe see section “Using the speaker terminals”. Connect power to the Hub Connect the power cable to the power supply and the power supply to the Hub. Plug the power cable into an un-switched power outlet.
Digital sources
(Airport Express, Apple TV, computer, blueray, HTPC, dvd, TV, video games, etc)
Analog source
(mp3-player, bluetooth receiver, ect.)
Subwoofer
Power supply
Subwoofer
Power supply
Digital sources
(Airport Express, Apple TV, computer, blueray, HTPC, dvd, TV, video games, etc)
Analog source
(mp3-player, bluetooth receiver, ect.)
Subwoofer
Power supply
4
6. Decrease volume button Press this button to decrease the output sound volume.
NOTE: Before remote control installmarked batteries and remove the front protection film. Not 1. Insert the metal pin in the hole at the back of using thethe remote control removing the protection film may decrease or block the touch sensitivity. Fig 1 “Push here to open”. Activating the system using the Touch Remote 4.1 Installing/replacing the remote control batteries 2. Push firmly inwards until the front panel and housing separated asremote control must be To install/replace the remoteiscontrol batteries the Open the Remote by pushing opened using included opening pin (figure 1) or similar thin sturdy object. depicted in figure 2. the included pin into the small hole on the back. Give it a The process of system activation gentle push. 1.replace Insert the both metal pinbatteries inbut thefirm hole atat thethe back of the remote control marked 3. Install/replace the batteries. Always Fig 1 illustrated on these pages is “Push here to open”. Insert batteries same time. Use AAA size batteries. identical, regardless of which 2. Push firmly inwards untiland theclose front panel and housing is separated as correctly depicted in figure 2. the remote. Opalum active speaker model Push
you have.
he
re
to
op
en
->
3. Install/replace the batteries. Always replace both batteries at the NOTE: Batteries must be inserted with correct polarity according to the same time. Use AAA size batteries. picture on the battery holder. Fig 2
Pus
h her
e to
ope n ->
NOTE: Batteries must be inserted with correct polarity according to the
pictureAon thestudy battery 4. Re-assemble the front panel and housing. Fig 2 brief ofholder. the most simple Remote you´ll ever use. 4. Re-assemble the front panel and housing. Make sure to align both parts properly using the Input source colour indicator Make sure to align both parts properly using the alignment tab, see figure 3. The parts will thentab, see figure 3. The parts will then alignment Power on/off magnetically snap together. magnetically snap together.
3
Volume up/down Fig 3
Connect input sources
Toggle between input sources Depending on your choice of sources and connection cables from, connect the cables to the correct terminals on the Hub. The type of terminal is indicated on the Hub in both colours and text.
Digital sources
In most cases the system won´t require a subwoofer, should you happen to be Sound but Technology a fan of extreme deep and vibrant bass, just connect your subwoofer to the Hub and turn the low-pass frequency setting to max.
Analog source
Only thing you need to adjust is the subwoofer level.
(Airport Express, Apple TV, computer, blueray, HTPC, dvd, TV, video games, etc)
(mp3-player, bluetooth receiver, ect.)
Subwoofer
Fig 3 19
Sound Technology
Activating the Opalum Sound System •
Turn on power to all input sources and the system itself.
•
The system will automatically turn on and be set to ‘pink’ input.
•
Use the input toggle on the remote to select your choice of source. (The indicator lights changes colour simultaneously on both the remote and the front of the Hub, to show the input selected).
Now you should be listening to the deep rich sound of the Opalum Sound System. Enjoy ...
19
Main Office: Opalum ApS • Ørstedsvej 10 • DK-8660 Skanderborg • T.: +45 7877 0500 Opalum US , Inc • 2118 Plum Grove Rd. #208 • Rolling Meadows, IL 60008-1932 • Phone: +1 847 254 9898
