Preview only show first 10 pages with watermark. For full document please download

Install Sheet Sharp Pds 01

   EMBED


Share

Transcript

KIT_VR2004_SHARP_PDS Interconnection Diagram SHARP ECR Your Camera (Set serial port for Print Data Send) RJ45 to DB9 Adapter CAT5 provided by customer Text Inserter RJ45 to DB9 Adapter Serial Out to real printer or Handshake RCA Cable & Adapter(s) Text On Your CCTV Handshake (Loop Back) Wall Transformer Step by Step Instructions: 1. Power off the ECR. 2. Connect the RJ45 to DB9 adapter on the appropriate serial pot of the Point of Sale system terminal. 3. From the RJ45 to DB9 using a long CAT5 cable provide by the installer, connect to the second RJ45 to DB9 adapter provide in the kit. 4. Attach the RJ45 to DB9 adapter to the Serial Input on the Text Inserter. 5. Attached the Handshake adapter to the Serial Out on the Text Inserter OR connect a user provided DB9 from Serial Out to a real printer. 6. Connect the appropriate camera cable to the Video Input of the Text Inserter, and connect the Video Output to a monitor or DVR. The BNCF to RCAM adapters are usually required. 7. Apply power to the VR2004 Text Inserter with the transformer. 8. Apply power to the sales terminal. 9. If necessary, the store owner or their technical support will set up the terminal for the serial port is output of type “Print Data Sending”. 10. Watch the monitor and make a sale or other transaction on the cash register to test the installation and observe the inserted text on a monitor. (Note with the default settings, the text erases after 10 seconds. You many need help to test or sprint from the terminal to the video monitor.) Typical connections to ECR and CCTV VRX is simple to use! Install_Sheet_SHARP_PDS_01.odt VRX Company Inc. www.vrxinc.com Phone: 866-543-8398 Text Inserter Kit for ECRs Kit VR2004_SHARP_PDS Description Item list: 1. Text Inserter set for Journal Printer 2. Wall Transformer 3. RJ45 to DB9 adapters for easy CAT5 wirring* 4. Handshake adapter (simulates printer connections) 5. RCA Cable 3 FT 6. BNCF_RCAM 7. BNCM_RCAF *Not included. A long CAT5 (Ethernet) cable to connect from the cash register to the DVR. No Text: Check for proper power to all devices. Check for data into Text Inserter: Observe the MULTI FUNCTION LED on the Text Inserter. It will blink once at power up. It will blink on and off slowly when the Text Inserter is operating normally but idle (not receiving data). The LED will blink rapidly (possibly appearing half brightness) when the Text Inserter is receiving data. Examine all RJ45 connections checking for full insertion and retention of the cables into the adapters. Check for bent wires in the RJ45 connections. Supported SHARP Models and Requirements: See our web site for an up to date list of supported models as well as set up notes for the registers themselves. Set the cash register serial port as follows: 9600 bps, 7 Data, 1 Stop, EVEN Parity. Serial Port data “Print Data Sending”. More Information. Text Inserter User Settings: Serial Menu: Serial bps 9600 7 E 1. POS type menu: POS SYSTEM TYPE: SHARP ASCII DB 9 Device: EPSON PRINTER DB25 Device: ALARM OUTPUT DISPLAY MODE: ALL LINES SCREEN DELAY: 1 s (Second) Text Inserter Menu: TIMEOUT: 10 SECONDS DISPLAY: 24 Chars x 12 Lines REMOVE MULTI-SPACE: YES ALARMS: OUTPUT DB25 Debug Menu: HEX DUMP: OFF For additional instructions on other Text Inserter features, see the user interface instructions in the full user manual at: www.vrxinc.com/documents/VR2004POS_UserManual_1_0. pdf Warranty Summary One year parts and labor for defects in materials and workmanship. Repair, replace or refund at manufacturers discretion. See the on-line user manual for full warranty. NOTE: Damage due to lighting or mis-installation not covered. Jumper Locations Internal jumpers J1, J2 and J3. J1 set for pins 1-2. (RX Echo). J2 and J3, Set for pins 1-2. (FLOW CONTROL for proper Screen Delay) Note: Position 1-2 are toward the center of the PCB. Troubleshooting If necessary, the store owner or their technical support will set up the terminal for the serial port is output of type “Print Data Sending”. The handshake adapter must be connected to the Serial Output of the Text Inserter. Install_Sheet_SHARP_PDS_01.odt VRX Company Inc. www.vrxinc.com Phone: 866-543-8398