Transcript
Getting to know your CRX1 wireless controller
Installation and Control Guide for
CRX1
programme number in SETB & PROG mode time
Single Zone Wireless Controller
The CRX1 is a wireless thermostat giving high precision room temperature control. It is also a 7 day programmer with up to 6 temperature settings per day. Each CRX1 can control any number of heaters in the same room (zone).
control icons
An illustration of functions available on CRX1.
Batteries
Remove the CRX1’s battery cover and insert 2 new high quality alkaline AAA batteries.
: set time, day and accessing programming menu : activate fan function (for fan heaters only) : select operating mode : increase value : decrease value ALARM!: flashes to indicate error in temperature settings for the day e.g. the timing set for 2nd temperature setting precedes the 1st temperature setting.
Warning: Consort is not responsible for damage due to corrosion. Battery leakage will cause permanent damage. To help avoid this:
•
Replace the batteries annually, even if there is not a low battery warning. Remove failing or flat batteries immediately. Always fit a pair of new high quality alkaline batteries from the same pack. Never mix new and old batteries, or batteries of different brands or types. Never attempt to revive alkaline batteries by heating, crushing or recharging.
Note: The clock has to be set after replacing the batteries. All other settings are unaffected.
Pairing CRX1 with heaters
This must be done, otherwise the heater will not work.
Set heater into pairing mode. 1. Turn the power to the heater on. Count 4 seconds, turn power OFF. 2. Turn the heater back ON, the light should be flashing green. (If the light isn’t flashing green, the 4 seconds timing was incorrect. Repeat step 1.) 3. The heater is now ready for pairing with CRX1. This has to be done within 30 seconds. After 30 seconds the heater will return to normal operating mode. Set CRX1 into pairing mode. 1. Touch and hold and icons together for 10 seconds. 2. The display will show the CRX ID number. 3. Tap the button while the light on the heater is flashing green. If the pairing was successful, the light will stop flashing and the heater is paired with CRX1. This has to be done within 30 seconds. After 30 seconds, the CRX1 will return to normal operating mode.
child-lock fan radio transmit symbol
programming options
Overview
•
room temperature
set temperature
Please read this guide carefully and retain for future use and maintenance.
•
alarm notification battery capacity heater active symbol operating mode
day
Setup menu 1. 2. 3. 4.
Touch and hold and icons together for 10 seconds. The CRX1 will enter the setup menu. Use and to change a value. Use to scroll between the settings.
01 – temperature calibration The temperature reading has been factory calibrated but if for any reason it needs adjusting (better accuracy required, to suit different position in the room etc.) the reading can be recalibrated in 0.5 degrees steps. 02 – change between degrees Celsius or Fahrenheit 03 – set maximum temperature 04 – set minimum temperature (- - - = heating OFF, 4deg = frost protection) 05 - information about the software version
Choosing a position in the room
The CRX1 should be positioned in the same room as the heater. It should be where its temperature will not be changed by local effects. Avoid: • •
Draughty places near windows, doors and vents. Places near the heater itself or any other heat sources in the room.
• • •
Places where the sun will shine on it. Places where, for example, it could be hit by a door. Places where it may get wet.
Fixing CRX1 to the wall
Remove the wall plate from the rear of the CRX1 and mark through the screw holes on the rear. Drill and plug the wall to accept No. 6 or No. 8 screws and mount the wall plate. Attach the CRX1 back onto the wall plate and tighten up the screws below.
Using CRX1 with supplied table top stand
CRX1 comes with a table top support that can be screwed to the back of the unit, allowing it to stand upright on most flat surfaces.
Basic operation
Before you can use CRX1, it has to be activated by tapping any control icons. The LCD screen backlight will turn on upon activation. To operate any control icon, tap within 2 seconds of CRX1 activation. As the CRX1 does not have any pre-set programming, you will need to set the day, time and day programmes. To enter any programming mode, touch and hold for 5 seconds.
Set time and 7-day programme day programme number in SETB & PROG mode time for programme 1 temperature for programme 1 programming options
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Touch and hold for 5 seconds to enter the time setting. The minutes will flash. Tap or to set the minutes. To set hour, tap and the hour will begin to flash. Tap or to set the hour. To set day, tap and the day will begin to flash. Tap or to select the day. Tap to access the 7-day programming mode. Tap or to select the day you want to set. Tap to set programme 1 for selected day. This is indicated by the flashing number next to PROG. Tap or to select the temperature setting you want to program i.e. 1 to 6 Tap to select minutes. Tap or to set minutes. Tap to select hour. Tap or to set hour. Tap to select temperature. Tap or to set temperature.
Note: The programme is inactive if time and temperature are showing dashes. Tap once to activate the temperature setting selection before you programme the time and temperature. In order to set the next temperature setting for the same day: 1. Tap until you reach the temperature setting options again. 2. Tap or to select the next temperature setting for the day. 3. Then follow steps 8 to 13 above. To set temperature settings for a different day: 1. Navigate by tapping until the selection for day is flashing. 2. Then, follow steps 5 to 13 above. Tip: You can copy a day’s heating schedule by using the “COPY DAY” option in programming mode. Note: Once you are happy with the settings, leave the thermostat for 20 seconds or tap and hold for 5 seconds. The settings will be saved and CRX1 will return to the main screen.
Copy day heating programme
The CRX1 allows you to copy a day’s heating programme to save time re-entering the temperature settings for a day. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Touch and hold for 5 seconds to enter the time setting. The minutes will flash. To skip time setting, tap to cycle through hour and day. On the next tap, the Programme mode is activated and the day will flash. Tap to activate the COPY DAY function. Tap to select the day you want to copy the temperature settings from. Tap or to select the day you want to copy the temperature settings to. Tap to confirm the selection. The ‘to’ word will flash to indicate that the day programme has been copied to the day selected. Tap to go back to the Programme mode.
Set programme inactive
To deactivate a programme, enter the programming mode. Select the programme you want to make inactive and tap . The time and temperature will now be dashes to indicate that the programme has been deactivated. In order to re-activate the temperature setting, tap again.
Operation modes
CRX1 has 4 operating modes: BOOST, MANUAL, SET BACK and PROGRAM. Each mode can be selected by activating the CRX1 and tapping to cycle through the options. The cycle sequence will always start with BOOST mode followed by MANUAL, SET BACK and PROGRAM.
15-Minutes Boost mode - BOOST
The boost feature regulates your heating to increase the room temperature to provide the maximum comfort quickly. 1. To activate Boost feature, tap twice. 2. The Boost mode will show above the current temperature and the 15-minutes timer will flash. 3. Tap or to set the temperature. 4. Once the temperature is set, wait for a few seconds for to flash. 5. The heating is now in Boost mode. To amend the set temperature, tap any control button once to activate, then tap or to change the temperature. Once the temperature is set, you can leave the thermostat and the settings will be saved. After 15 minutes, the CRX1 will return to normal operating mode.
Manual mode - M
In manual mode, the heater maintains the set temperature. 1. To activate manual mode, tap twice. 2. Tap to cycle through to MAN operating mode. 3. Tap or to set the temperature. To amend the set temperature, tap any control button once to activate, then tap or to change the temperature. Once the
temperature is set, leave the thermostat and the settings will be saved.
Setback mode - SETB
The setback feature lowers all set temperatures in the 7-day programme by a set value. 1. To activate setback mode, tap twice. 2. Tap to cycle through to SETB operating mode. 3. Tap to decrease the temperature.
Programme mode - PROG
In this mode, the CRX1 will follow the day programme. You can override the temperature in PROG mode by simply activating the CRX1 and using the or icon to adjust the temperature. The temperature set will then be maintained until the next temperature setting for the day kicks in.
Fan function
Tap any control icon to activate the CRX1. Tap deactivate the fan function.
to activate or
Advance mode
Tap from SETB or PROG mode to bring forward next programme. To clear advance mode, tap .
Locking CRX1 Tap and hold unlock CRX1.
together for 5 seconds. Repeat the step to
Customer helpline
Should you need any advice on the use of your new Consort product, or should you require service or repair, please contact our Helpline: Tel: 01646 692172 Fax: 01646 695195 Email:
[email protected] The CRX1 is guaranteed for one year against faulty material or workmanship. This applies only if the appliance has been used for purposes in accordance with the instructions provided and has not been misused, neglected, damaged, modified or repaired by any person not authorised by us. This guarantee is offered to you as an extra benefit and does not affect your legal rights.
Consort Equipment Products Ltd.
Registered Office: Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT Tel: 01646 692172 Fax: 01646 695195 Sales enquiries:
[email protected] Technical enquiries:
[email protected] BS EN ISO 9001 Registered Company No FM12671 Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the interest of progress the Company reserve the right to vary specifications from time to time without notice.
