Transcript
K3590-FBIIV1 6/01
REMOTE KEYPADS Omni®-KP & Omni®-LCD (Omni-LCD is not available in the U.S.)
INSTALLATION AND SETUP GUIDE Omni-KP Fixed-Word YES Piezo
Keypad Features Backlit Display Built-in Sounder
Omni-LCD 2-Line Alpha YES Speaker
ARMED
KEYPAD DISPLAYS AND LEDS
READY
STAY
1
2
3
BYPASS
4
5
6
INSTANT
7
8
9
0
#
The keypads have the following display features: Model Omni-KP Omni-LCD
Fixed Word Display X
2-line Alpha Display
2-digit Zone Identifier X
Custom Zone Descriptors
X
X
CODE
omni-KP-001-V0
The Omni®-KP and Omni®-LCD are addressable Remote Keypads designed for use with FBII Omni Series control panels. Addresses are set via the keypad keys. The keys on the keypads are continuously backlit for convenience.
Omni-KP w/ Protective Cover Removed
Function Lights when the system is armed in any mode
Green
Lights when the system is "ready" to be armed.
WIRING AND INSTALLATION The keypads can be surface-mounted directly to a drywall, or to a single- or double-gang electrical box. 1. Remove the case back by sliding the blade of a screwdriver-between the tab and the case back on each side of the keypad as shown in lower diagram at right. 2. Route wiring from the control panel through the opening in the case back. 3. Mount the case back to a wall or electrical box. For wall mounting of the Omni-KP/LCD in the FR, NL and IT versions, secure the case back to the wall, being especially careful to secure the partially knocked-out tamper switch plunger with its own screw. This assures that separation of the keypad from its mounting will cause the tamper switch to activate. Any attempt to pry the keypad open will also activate the tamper switch in these versions. 4. Wire directly from the keypad’s terminal block to the terminal block on the control board. Wire functions are marked next to terminals. Labels are as follows: DI Data In to Control Panel, - Ground, + Aux. Power Plus, DO Data Out of Control Panel. See table on next page. 5. Reattach the keypad to its case back.
ARMED
STAY
1
2
3
READY
BYPASS
4
5
6
INSTANT
7
8
9
0
#
CODE
Omni-LCD w/ Protective Cover Removed
TO SEPARATE TOP COVER INSERT SCREWDRIVER AND PUSH HERE
D
ARME
Y READ
omni-LCD-002-V0
LED Red
omni-LCD-001-V0
The following table shows the LEDs and their functions:
Separating Case Back From Top Cover
USING THE SOUNDER MENU (Omni-LCD only)
TURNING BACKLIGHT TIMER ON and OFF Omni-KP Press and hold down the INSTANT and CODE keys at the same time for about three seconds. Press the [1] key that toggles a zero or one in the display: 0 = Backlight always on 1 = Backlight on an approximate 120-second timeout Press [✱] key to exit this Backlight menu.
Omni-LCD Press and hold down the INSTANT and CODE keys at the same time for about three seconds. Press the [1] key to toggle the display between: 0 = Backlight always on and 1 = Backlight on an approximate 120-second timeout.
Press the BYPASS and CODE keys at the same time and hold down for two seconds. This accesses the Sounder Menu. 1. Press the [1] key to toggle through the following four modes and stop at desired mode. On - Normal Sounder Keys (all sounds on) Key - Only Key Clicks Fire - Only Fire Sounder (temporal sounder – not supported by all panels) Off - No Sounds at all 2. Press the [2] key to toggle through the sounder volume choices (high or low appears on the display). 3. Press the [3] key to adjust the sound of the key acknowledge (Ack H or L appears on the display). 4. Press the [✱] key to exit the Sounder Menu.
SPECIFICATIONS Physical: Omni-KP: 5"H x 6-1/2"W x 1-5/16"D Omni-LCD: 5-5/16"H x 7-1/2"W x 1-5/16"D
Press [✱] key to exit this Backlight menu.
SETTING THE KEYPAD ADDRESS The keypad can be set for an address of 1-8. The keypad's default address is 8. To change the keypad's address, do the following: 1. Enter Address mode: Power up the keypad. Within 60 seconds of powerup, press and hold down the STAY and CODE keys at the same time for 3 seconds. If unable to enter Address mode (address is not flashing), power down, then power up and try again.) The current keypad address will be displayed. Select keys 1-8 to change the keypad address. If 10 seconds have passed with no key entry, the keypad automatically exits Address mode. 2. If the panel does not send a valid command to the keypad, the display will remain blank. 3. Exit Address mode: Press [✱] key to save the displayed address and exit Address mode.
Wiring (all Keypads):
x
Keypad Terminal DO or
+ – DI
or
z
Control Panel Terminal GRN RED BLK YEL
Displays: Omni-KP: Fixed-Word LCD (backlit). Omni-LCD: 2 x 16 alpha-numeric supertwist LCD, backlit.
Sounder: Omni-KP:
Omni-LCD:
Piezo-electric (fire alarm is loud, pulsing single tone; (all Keypads) burglary alarm is loud, continuous, dual tone). Speaker.
VIEWING THE KEYPAD ADDRESS
Current:
Press and hold down the STAY and CODE keys at the same time for about 3 seconds. The current address is displayed. No key entry is allowed. Press [✱] key to exit or wait 10 seconds to automatically exit viewing mode.
Omni-KP:
In alarm ................................ 70mA Standby (Backlight off/on)..... 28mA/45mA
Omni-LCD:
In alarm ................................ 130mA Standby (Backlight off/on)..... 35mA/81mA
TURNING THE SOUNDER ON/OFF NOTE: Chime will not operate if keypad sounder is disabled (off).
Omni-KP: Press the BYPASS and CODE keys at the same time and hold for two seconds until you hear a beep. Press any key to toggle sounder on and off. 0=Sounder off, 1=Sounder on Press [✱] to exit and save this setting.
REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
180 Michael Drive, Syosset, NY 11791 Copyright 2001 PITTWAY CORPORATION
¬. )%,,91l K3590-FBIIV1 6/01
