Transcript
Installation and Setup of the 4281/5881 Wireless Receivers 1. Mount the receiver(s). Receivers must be mounted externally to the control and can detect signals from transmitters within a nominal range of 200 feet. Take this into consideration when determining mounting location. 2. Connect the receiver's wire harness to the control's keypad terminals (6, 7, 8, and 9). Plug the connector at the other end of the harness into the receiver (see Figure 15). 3.
Refer to the installation instructions provided with the receiver for further installation procedures regarding antenna mounting, etc.
ANTENNAS INSERT IN RIGHT-HAND TERMINALS YELLOW RED BLACK GREEN
@@@@@@@@e? @@@@@@@@e?@@@@@@@@e?@@@@@@@@?e@@@@@@@@e? @@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ @@@@@@@@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@
CIRCUIT BOARD MOUNTING HOLES
INTERFERENCE INDICATOR LED
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@ @@ @@ @@ @@ @@ @@ @@
@@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@@@@@@@ ?@@@@@@@@ @@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@
DIP SWITCH
PLUG & SOCKET
}
WIRING OPENING
TO CONTROL’S REMOTE KEYPAD CONNECTION POINTS. EACH RECEIVER MUST BE ON INDIVIDUAL HOME RUN.
KNOCKOUT AREA FOR SURFACE WIRING ON
OFF 5 4
DIPSWITCH POSITION #5 (PRESENT ONLY ON 5881EH) ON: SETS 5881EH FOR USE IN COMMERCIAL FIRE APPLICATIONS (SEE THE RECEIVER’S INSTRUCTIONS). OFF: USE IN NON-COMMERCIAL FIRE INSTALLATIONS.
3 2
NOTE: SWITCH POSITION 5 PRESENT ON 5881EH ONLY.
1
Figure 15: 5881 Wireless Receiver (cover removed) 4. Set the receiver's DIP switches for an address (01-07) which is not being used by another device (i.e., keypads, relay modules, etc.). Take note of the address you select for the wireless receiver as this address must be enabled in the system's Device Programming mode (described later in this section).
– 43 –
Installing the 5800TM Module Installation of this module is necessary only if you are using one or more 5827BD Wireless Bi-directional keypads. The 5800TM must be located between one and two feet from the 4281 or 5881 receiver's antennas. The 5800TM must not be installed within the control cabinet. Mount the unit using its accompanying mounting bracket. 5800TM Wiring Connections Connect the 5800TM to the control panel’s keypad connection terminals, using the supplied connector with flying leads, as follows: WIRE RED (+12VDC) BLACK (Ground) GREEN (Data to Control) YELLOW (Data from Control) BLUE: Not Used
TERMINAL ON CONTROL Terminal 6 Terminal 7 Terminal 8 Terminal 9
Cut the red jumper for address setting 28; cut the white jumper for address 29; cut both jumpers for address 30. This address must be enabled as an alpha keypad in the control's Device Programming mode and then assigned to a partition, as described later in this section. For additional information, refer to the 5800TM’s instructions. Programming The Wireless Receiver 1.
With at least one two-line alpha keypad (5137AD/6139) wired and set to a proper address, power up the system temprarily by plugging the AC transformer into a 120VAC outlet (previously wired to the control).
2.
Enter data field programming mode: Installer Code + 8 0 0 . a. If using a 4281: set data field 1*32 to 1 If using a 5881: set data field 1*32 to 2 b. Set data field 1*30 RF RCVR CHECK-IN INTERVAL (02-15 times 2 hrs.).
3.
From data field programming mode, press #93 to display the "ZONE PROG?" prompt. Press 0 (NO) repeatedly until the "DEVICE PROG?" prompt appears. Follow the instructions below. DEVICE PROG? 1=yes 0=no
Press 1 to enter DEVICE PROGRAMMING mode.
DEVICE ADDRESS? 01-31
Enter the 2-digit device address number as set by the receiver's DIP switches (01-07). Press * to continue.
DEVICE TYPE
Enter device type 03 = RF Expander. Press * to continue.
RF EXPANDER HOUSE ID XX
Enter the 2-digit house ID (00-31) as determined by sniffer mode (use an ID not displayed during sniffer mode, as explained later in this section). Applies only to 5700 series systems or if using a wireless keypad (5827/5827BD) with 5800 series systems. Press * to continue. The system will now prompt for the next device address to be programmed.
–44–
