Transcript
Installation Guide Body Jets
Thank You For Choosing Valley Acrylic All the information in this guide is based upon the latest product information available at the time of publication. We reserve the right to make changes in product characteristics, packaging, or availability at any time without notice. Please take a few minutes to review this guide. If you encounter any installation or performance problems, please call 1-877-398-tubs (8827) from within the USA and Canada.
www.valleyacrylic.com
GENERAL REQUIREMENTS IMPORTANT: For easy installation, please read all of the instructions completely before beginning. YOU MAY NEED:
H10 Wrench
H2 Wrench
Screwdriver
Sealant Tape
• To avoid the impact of poor water quality on the usage of the procut we recommend that you install an aerator in the water supply pipe. • The main body is in its best situation before leaving the factory Please do not disconnect the faucet body by yourself. MAINTENANCE 1. Replacement parts may be available at the store where you purchased your product. CLEANING INSTRUCTIONS 1. To keep the product clean you should clean frequently. 2. Clean the product with water then dry with soft cotton cloths. 3. Do not use any abrasive cleansers, cloths, or paper towel. 4. Do not use any acidic or abrasive detergent.
INSTALLATION PROCEDURES
1
2 4
3
5
6
7 1. Pipe 2. Plastic Box 3. Decorative Plate 4. Connector 5. Body 6. M4X20 Bolt 7. Outlet face 8. M4X12 Bolt 9. Decorative plate
8 9
See the dimension drawing below:
120
102
Connect to side spray
112 Water supply fitting
Wall
130
1. Preparation Before installation you should pay attention to the following three points: 1.1 C heck the new product for damge, if the product is damage, please contact us. 1.2 Check to see if all accessories are included in packaging. 1.2 Flush the water supply fittings Connect to side spray
Water supply fitting
Wall
2. Installation 2.1 The new product is assembled before leaving the manufacturer, please disassemble the product before installation as per the instructions.
Step 1
Push this hole Remove the decorative plate Out of the body
Push this hole
Remove the decorative plate
Step 2
Remove the M4X12 scre and the outlet face Remove the M4X20 scre and the connector body
2.2 Please see installation instructions below
INSTALLATION PROCEDURES
103-110
Step 1
113-120
Size
65mm Notice: The distance between the water supply
Unit: mm
system and the finished wall shall be at least 65mm
Step 2
41- 48
• Screw the pipe to the water supply fittings • The distance betwee end point of the pipe and finished wall shall be 41 mm to 48mm. cut off the longest part • Then take off the pipe, screw the sealant tape to the pipe, screw to water supply fittings again. • Turn on the water supply system to flush the pipe • Close the water supply system Unit: mm
Step 3
• Push the plastic box into the wall • Make sure the side with the “UP FACE” mark is in the top position
Step 4
• Install the decorative plate assembly into the plastic box • M ake sure the position is correct
Step 5
• Screw the connector into the with with H10 wrench • Be careful of the decorative plate assembly
Step 6
Make sure the body connection to the connecter is complete
• Install the body assembly to the connector • When finished installation please check connection
Step 7
• Screw the M4X20 bolt into the body • Make sure the body and the connector are tightened • Make sure the decorative plate is not moved
Step 8
Fixtures Fixtures Make sure the one side bulge is in the top position
• Install the outlet face assembly to the body • Makse sure the connecto of body and outlet face assembly is complete • Screw the M4X12 bolt through the outlet face into the body. don’t use excess forece or else the outlet face will be damaged.
Step 9
Make sure the hole and the bulge are in the correct position.
Step 10
Install decorative plate
This side is in the bottom position when pushing the decorative plate into the body first
• Screw the outlet face at a slight angle • Make the decorative plate has a slight angle too when pushing it into the body • Adjust the outlet face when pushing the decorative plate in order to put it out of the decorative plate
1. 0.5 bar is the products minimal supply pressure, for the best shower effect it is best to use above 1.0 bare supply pressure. 3. Flow rate illustration
Maintenance and Cleaning The product will have debris inside of the body when you use it daily. Clean as follows:
Protect the decorative plate coating when removing it. Use screwdrive to remove
• Remove the decorative plate at a slight angle • Use screwdriver to remove the decorative plate
