Transcript
SPOTMOD® LINK
®
QUICK SPECS Input
12VDC Constant Voltage
Power
4W
Dimmable
Yes
Max Daisy-Chain
7 units
Environment
Damp / Indoor
Included Models
DI-12V-SPOT-LK-**
** Indicates CCT, CRI, finish.
IG062816-2.0
SAFETY / WARNINGS / ATTENTION! • Install in accordance with the NEC and local regulations. • This product is intended to be installed and serviced by a qualified, licensed electrician. • DO NOT Connect to 120VAC Power. • This product MUST be powered with a compatible Class 2 12VDC LED driver and has not been evaluated for use when connected to a power source that does not comply with Class 2 voltage and energy limited supplies. • CAUTION: To reduce the risk of fire, do not install in a compartment smaller than 2.5 in. x 2.5 in. x 0.27 in. • Suitable for recess mounting only inside a cabinet. • Suitable for Damp Locations. Do not install in wet locations or outdoors. • Attached wire leads, connectors and accessories are not rated for in-wall installation. • Attached wire leads are field-cuttable.
READ ALL INSTRUCTIONS PRIOR TO INSTALLATION
SURFACE MOUNTING (Fig. 1 & 2)
ACCESSORIES Item #
Color / Finish
DI-SPOT-LK-ADP (Not Included)
LINK DC Adapter Cable
DI-SPOT-5EXT (Not Included)
SPOTMOD 5ft. Extension Cable
1. Pop puck off mounting ring. 2. Route cords through ring and set in notches. 3. Mount ring to surface with 2x screws (included) and Phillips head screwdriver (not included). 4. Gently pull cord slack and pop puck into ring. If daisy cord isn’t needed, wrap around puck before mounting (Fig. 2).
For hard-wired installations, cut off unused connector and strip wire leads. This will not void product warranty or certification.
Fig. 1
Fig. 2
RECESSED MOUNTING (Fig. 3 & 4)
PLUG-IN ADAPTER INSTALL
SWITCHEX® DIMMER INSTALL
TROUBLESHOOTING
1. Drill a hole through cabinet or shelf with a 2 1/4 in. hole saw and drill (Fig. 3). 2. Pop puck off mounting ring. 3. Route cords through pre-drilled hole (Fig. 4). 4. Pop puck into hole and push firmly into place (Fig. 4).
1. Attach fixture(s) to inline accessories. 2. Attach system to 12VDC plug-in adapter. 3. Plug adapter into 120VAC electrical receptacle.
1. Turn power OFF at circuit breaker. 2. Cut off DC barrel of SPOTMOD DC Adapter Cable. Strip wires and hard-wire to SWITCHEX Dimmer. 3. Connect adapter cable to SPOTMOD. 4. Turn Power ON at circuit breaker. Refer to SWITCHEX install guide for more information.
• Fixture does not illuminate: Check that polarity at all connection points are secure and not reversed. • Fixture is flickering: Ensure a compatible system is installed. Refer to the power supply compatibility list when installing dimming controls. Ensure all connections are properly secured. • Fixture is overheating: Ensure fixture is installed in a wellventilated area. • Fixture turns ON/OFF continuously: Ensure driver is not overloaded.
Class 2 Low Voltage Plug-In Adapter AC Power 50/60Hz
SPOTMOD® LINK DC ADAPTER CABLE
SWITCHEX
(Dimmer + Driver)
120 VAC ~ 60Hz
V+
L (BLK) N (WHT)
SPOTMOD® LINK
SPOTMOD® LINK
12 VDC Ground (GRN) SPOTMOD® LINK
OMNIDRIVE , REIGN Dimmer, TOUCHDIAL™, and more installation diagrams are available at www.DiodeLED.com. ®
Fig. 3
Fig. 4
V−
SPOTMOD® LINK DC ADAPTER CABLE (w/ Cut off DC Barrel)
®
QUESTIONS? Toll Free 877.817.6028 ®
[email protected] www.DiodeLED.com
