Transcript
4-455-814-13 (1)
Notes SRG-120DH HD Camera Unit 3)
HD Visual Communication System PCS-XG100/XG77/XG100S/XG77S
to HDMI
Installation Guide
to VISCA IN
ˎˎ Be sure to turn off all the equipment before making any connections. ˎˎ Do not connect/disconnect the camera cable, interface cable, or pen tablet with the power on. Doing so may damage the camera unit, Communication System, or ISDN unit. ˎˎ For safety, do not connect the 1000BASE-T connector to a network that will apply excess voltage to this connector. ˎˎ When used with an ISDN unit for the first time, the Communication System may automatically upgrade the software of the connected equipment. Follow the instructions on the monitor screen to upgrade the software. Do not turn off the Communication System or disconnect the cable during upgrade. Doing so may cause a malfunction of the system. ˎˎ ISDN support is planned for version 2.0.
to DC 12V
Camera cable 1)
Connections
VCR, etc.
Supplied Supplied (two PCS-A1 microphones are supplied with the PCS-XG100/XG100S, and one is supplied with the PCS-XG77/XG77S) 3) Supplied with the PCS-XG100/XG77 4) Supplied (Japan only) 5) Not supplied 6) Output to HDMI monitors under default settings. When outputting to a non-HDMI monitor, refer to the “To change the ‘Monitor Output’ setting” section on the reverse side.
Computer
1) 2)
to CAMERA
Front
HDMI cable 5)
DVI cable 5)
to HDMI IN
to DVI-I 2 (PC) IN
Rear
PCS-A1 microphone 2) Connecting two microphones allows pickup of stereo sound. to MIC (A1) 1 (R) / 4 (L)
1080 60P CAMERA LAN1-ALERT-LAN2
DVI-I 1
MIC(A1)
DVI-I 2(PC)
HDMI
I N
ONLINE
1(R)
2(R)
3(R)
4(L)
5(L)
6(L) R
L
AUDIO 1 IN O U T
ˎˎ The PCS-XG77/XG77S is not equipped with the following connectors and indicators: HDMI IN, HDMI-2 OUT, and 2 connectors, and LAN 2 ALERT indicator ˎˎ On the PCS-XG77/XG77S, the 1 connector is named the connector, and the LAN 1 ALERT indicator is named the LAN ALERT indicator. ˎˎ Normally, connect the UTP cable to the 1 connector (indicated in green). If the UTP cable is connected to the 2 connector, some of the functions of the system may be restricted. For details, refer to the Operating Instructions supplied with the system. ˎˎ The REC OUT jack is used to make an audio recording of a communication, for example. It is not used during regular communication. ˎˎ We recommend using Sony’s HDMI cable.
© 2013 Sony Corporation
Printed in China
(USB) port
2
DVI-I OUT
HDMI-2
to HDMI-1 OUT
to
L
R
L
R
L
REC OUT
AUDIO OUT
1 HDMI-1
Notes
R
AUDIO 2 IN
to DVI-I OUT DVI cable 5)
Pen tablet 5) (Wacom) TV monitor 5) 6)
to
ISDN UNIT
1
AUX CONTROL
to ISDN UNIT Interface cable (supplied with ISDN unit)
to TERMINAL
MAINTENANCE
to DC 19.5 V
Power cord 4)
AC adaptor 1) to power outlet PCSA-B384S 5) to ISDN 1 to 3 or PCSA-B768S 5) to ISDN 1 to 6
Projector, etc.
to HDMI IN
HDMI cable 1)
ISDN unit 5)
UTP cable (category 6, straight) 5)
ISDN modular cable
LAN
5)
ISDN line Continued on reverse side
Changing the “Monitor Output” and “Frequency” Settings with the Remote Commander If the “Monitor Output” and “Frequency” settings in the Video setup menu are configured incorrectly, pictures will not be displayed on the monitor. In such cases, use the (power) switch on the Communication System and the buttons on the Remote Commander to configure the correct settings.
To change the “Monitor Output” setting After verifying that the (power) switch indicator on the system is lit, perform the following.
Press the (power) switch on the Communication System. Within five seconds after you pressed the switch, press the buttons on the Remote Commander as follows, based on the desired “Monitor Output.” Desired “Monitor Output”
On the Remote Commander, press:
HDMI 1
VIDEO INPUT button (once) Number button 3 (three times)
DVI-I OUT
VIDEO INPUT button (once) Number button 4 (three times)
The “Monitor Output” setting is changed, and the picture appears on the monitor connected to the system.
To change the “Frequency” setting After rebooting the system and verifying that the (power) switch indicator changes from blinking to remaining steadily lit, perform the following.
Press the (power) switch on the Communication System. Within five seconds after you pressed the switch, press the buttons on the Remote Commander as follows, based on the desired “Frequency.” Desired “Frequency”
On the Remote Commander, press:
60 Hz
VIDEO INPUT button (once) Number button 1 (three times)
50 Hz
VIDEO INPUT button (once) Number button 2 (three times)
The “Frequency” setting is changed, and the system reboots. Note The Remote Commander cannot be paired with cameras.
“IPELA” and
are trademarks of Sony Corporation.
