Transcript
INSTALLATION GUIDELINES
Sample Installation:
INSTALLATION GUIDELINES
Paddle Switch, 2-Module | Catalog Number: ASPD1532
Frame
For more information and helpful how-to videos, visit www.adornemyhome.com/install.
2
If necessary, cut wires and strip insulation using stripping guide on back of switch.
1-POLE
Ground Wire
Paddle Switch
15A-120VAC
INSTALLATION INSTRUCTIONS Please read these instructions completely before you begin. adorne® switches are designed for installation in standard electrical boxes. However, some of the installation methods vary slightly from traditional methods. If you do not understand these instructions or are unsure of your abilities, seek the assistance of a qualified electrician.
STRIP GAGE #14-#12 AWG
3-WAY
Use only with Legrand adorne® system.
Wall Plate
3
1
WARNING Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.
Connect frame ground wire to bare ground wire in box. Fold ground wires into back of box. Mount frame to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT over-tighten.
TIPS • Pre-fold wires into wall box to make it easier to fit them in the box when switch is connected. • Use caution to avoid marring wall surface with the metal frame.
Common/Hot
Single Pole WARNING To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
74
When replacing existing switches, label wires before disconnecting. Disconnect old switch.
3-Way In a 3-Way circuit, identify the Common/Hot wire — connected to the terminal marked Common or the oddcolored terminal screw.
75
INSTALLATION GUIDELINES
Sample Installation:
4
Connect new switch as shown. Make sure the terminal holes are clear. Insert wires into terminals and tighten screws securely.
INSTALLATION GUIDELINES
Paddle Switch, 2-Module | Continued
NOTE - If you have purchased an adorne® Locator Light or Accent Nightlight, please refer to those instructions at this step.
5
NOTE - If you are installing multiple switches in the frame, wire all devices before snapping them into the frame.
Carefully fold wires into box. Snap switch into frame.
NOTE – If you need to remove switch after snapping into frame, first remove frame from wall box to access the three locking tabs on the back of the switch. Insert a flat screwdriver to depress tabs as you apply pressure to push switch out.
1
2
3
6
Snap wall plate to frame. There are three click-stops to adjust the fit of the wall plate to the switch and the wall.
Single Pole • Connect one wire to 1-POLE. • Connect other wire to HOT. • Do NOT use 3-WAY. 3-Way • Connect the wire identified as Common/Hot in Step 1 to HOT. • Connect one of the other wires to 1-POLE. • Connect remaining wire to 3-WAY.
NOTE – To remove wall plate, insert a small, flat screwdriver in notches on wall plate and twist gently to pry from frame.
Never apply cleaner directly to the switch or wall plate. Apply to a soft cloth and use cloth to remove any smudges from the product.
WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.
Same size.
76
Different size with pigtail.
Different size.
77
INSTALLATION GUIDELINES
Sample Installation:
INSTALLATION GUIDELINES
Paddle Dimmer | Catalog Number: ADPD703H
Frame
Spacers
Paddle Dimmer
TOP
Wall Plate
CAUTIONS To reduce the risk of overheating and possible damage to other equipment, do not install incandescent dimmer to control a receptacle, a fluorescent light or bulb, a motor-operated appliance, or a transformer-supplied appliance. Do NOT use dimmer with incandescent lamps whose power requirements exceeds maximum wattage of the dimmer. Do NOT connect dimmer to power source other than 120VAC, 60 Hz.
2
If necessary, cut wires and strip insulation using stripping guide on back of dimmer.
STRIP GAGE
Ground Wire For more information and helpful how-to videos, visit www.adornemyhome.com/install.
T THOU LLED E WI T US INSTA DO NO PLATE LL A WA
INSTALLATION INSTRUCTIONS Please read these instructions completely before you begin. adorne® dimmers are designed for installation in standard electrical boxes. However, some of the installation methods vary slightly from traditional methods. If you do not understand these instructions or are unsure of your abilities, seek the assistance of a qualified electrician.
Remove spacers from the frame. Since this dimmer fills the frame completely, you will not need the spacers. From the back of the frame, pinch the tabs on the spacer to release.
Use only with Legrand adorne® system.
1
WARNING To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
When replacing existing dimmers, label wires before disconnecting. Disconnect old dimmer.
3
WARNING Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.
Connect frame ground wire to bare ground wire in box. Fold ground wires into back of box. Mount frame to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT over-tighten. (to 10 in. lbs.)
3-Way In a 3-Way circuit, identify the Common/Hot wire — connected to the terminal marked Common or the odd-colored terminal screw.
TIPS • Pre-fold wires into wall box to make it easier to fit them in the box when dimmer is connected. • Use caution to avoid marring wall surface with the metal frame. Common/Hot
Single Pole
78
79
INSTALLATION GUIDELINES
Sample Installation:
5
INSTALLATION GUIDELINES
Paddle Dimmer | Continued
Connect new dimmer as shown. Make sure the terminal holes are clear. Insert wires into terminals and tighten screws securely. Do NOT over-tighten. (to 10 in. lbs.)
6
Carefully fold wires into box. Snap dimmer into frame. TOP
NOTE - No multi-gang derating required.
NOTE – If you need to remove dimmer after snapping into frame, first remove frame from wall box to access the four locking tabs on the back of the dimmer. Insert a flat screwdriver to depress tabs as you apply pressure to push dimmer out.
1
2
1-PO
LE
NOTE - If you have purchased an adorne Locator Light or Accent Nightlight, please refer to those instructions at this step.
1-POLE 11-P -POL O E
3
HOUT LED E WIT T US INSTAL DO NO PLATE LL A WA
STRIP
4
HO OTT STR IP GA GE
STRIP GAGE
HO T 3-W AY
HOT
3-WAY
7
Single Pole • Connect one wire to 1-POLE. • Connect other wire to HOT. • Do NOT use 3-WAY.
High end light level adjustment The dimmer is pre-set so its highest setting provides maximum brightness. To reduce maximum brightness and save energy, you can adjust the high end light level. Remove cover assembly by pressing bottom center snap and lifting cover.
TOP
TOP
HOUT LED E WIT T US INSTAL DO NO PLATE LL A WA
TOP
HOUT LED E WIT T US INSTAL DO NO PLATE LL A WA
HOUT LED E WIT T US INSTAL DO NO PLATE LL A WA
NOTE - In a 3-Way installation, use one dimmer and one switch. Do NOT use two dimmers. 1-POLE
1
2
3
11-P -PO OLE
Rotate wheel downward to reduce output voltage. Maximum adjustment reduces output by 10%.
STRIP GAGE STR IP GA GE
HO
T 3-W AY
HOT
3-WAY
3-Way • Connect the wire identified as Common/Hot in Step 1 to HOT. • Connect one of the other wires to 1-POLE. • Connect remaining wire to 3-WAY.
8
Snap wall plate to frame. There are three click-stops to adjust the fit of the wall plate to the dimmer and the wall.
Replace cover assembly. Hook at the top and rotate down to snap into place. Note: Sliders need to be in the same position during cover re-assembly.
NOTE – To remove wall plate, insert a small, flat screwdriver in notches on wall plate and twist gently to pry from frame.
WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.
Same size.
80
Different size with pigtail.
Different size.
Wipe the dimmer with a damp, clean cloth. DO NOT clean dimmer with chemicals or cleaning solutions.
81
INSTALLATION GUIDELINES
Sample Installation:
INSTALLATION GUIDELINES
Tamper-Resistant Outlet | Catalog Number: ARTR152
Frame Outlet
For more information and helpful how-to videos, visit www.adornemyhome.com/install.
2
If necessary,cut wires and strip insulation using stripping guide on back of outlet. HOT WHITE
INSTALLATION INSTRUCTIONS Please read these instructions completely before you begin. adorne® outlets are designed for installation in standard electrical boxes. However, some of the installation methods vary slightly from traditional methods. If you do not understand these instructions or are unsure of your abilities, seek the assistance of a qualified electrician.
Ground Wire
Wall Plate
Use only with Legrand adorne® system.
Split Circuit Tab
3 1
WARNING To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
Connect frame ground wire to bare ground wire in box. Fold ground wires into back of box. Mount frame to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT over-tighten.
TIPS • Pre-fold wires into wall box to make it easier to fit them in the box when outlet is connected. • Use caution to avoid marring wall surface with the metal frame.
WARNING Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.
When replacing existing outlets, label wires before disconnecting. Disconnect old outlet.
Neutral (White) Hot (Black) Ground (Bare)
82
83
INSTALLATION GUIDELINES
Sample Installation:
4
INSTALLATION GUIDELINES
Tamper-Resistant Outlet | Continued
5
Connect new outlet as shown. Make sure the terminal holes are clear. Insert wires into terminals and tighten screws securely.
Carefully fold wires into box. Snap outlet into frame.
NOTE – If you need to remove outlet after snapping into frame, first remove frame from wall box to access the three locking tabs on the back of the outlet. Insert a flat screwdriver to depress tabs as you apply pressure to push outlet out.
1
NOTE - If you are installing multiple outlets in the frame, wire all devices before snapping them into the frame.
2 3
If you have four wires plus a ground wire
If you have two wires plus a ground wire
6
NOTE – To remove wall plate, insert a small, flat screwdriver in notches on wall plate and twist gently to pry from frame.
HOT WHITE
#14-#12 AWG
HOT
STRIP GAGE
STRIP GAGE
HOT WHITE
#14-#12 AWG
HOT
Snap wall plate to frame. There are three click-stops to adjust the fit of the wall plate to the outlet and the wall.
WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.
Same size.
Different size with pigtail.
Different size.
Never apply cleaner directly to the outlet or wall plate. Apply to a soft cloth and use cloth to remove any smudges from the product.
84
85
