Transcript
8
6
7
5
4
2
3
1
INSTALLATION INSTRUCTIONS:
1. PLACE THE DCPR.90 ON THE INDICATED SURFACE OF THE DOCKING STATION AND LINE UP THE HOLES WITH THE SLOTS ON THE SUPPLY, AS SHOWN.
DS.CFU1 DOCK (NOT INCLUDED)
D
2. INSTALL THE 4X #6-32 X 1-1/4" BUTTON HEAD CAP SCREW (BHCS) AND FLAT WASHERS THROUGH THE SLOTS OF THE POWER SUPPLY INTO THE HOLES ON THE DOCKING STATION, AS SHOWN.
POWER SUPPLY
D
3. AFTER ALL SCREWS HAVE MADE CONTACT WITH POWER SUPPLY, TORQUE SCREWS TO 8 10% IN-LBS. 4. ROUTE CABLES WITH ADEQUATE SERVICE LOOP TO ALLOW FREE MOTION OF THE DOCK AND SECURELY STRAIN RELIEVE CABLES MAKING SURE THEY ARE CLEAR OF ALL MOTION DEVICES AND PINCH POINTS.
4X #6 FLAT WASHER
C
5. INSERT POWER SUPPLY OUTPUT CABLE CONNECTOR INTO DOCKING STATION POWER RECEPTACLE AND SECURE TO OTHE UNDERSIDE OF DOCK USING THE ZIP TIES INCLUDED WITH THE DS.CFU1. SEE DS.CFU1 INSTALLATION SHEET FOR TIE WRAP AND WIRE ROUTING DIRECTIONS. 6. FULLY INSERT INPUT CABLE 12VDC POWER PLUG INTO VEHICLE CIGARETTE LIGHTER SOCKET. SEE POWER SUPPLY INSTALLATION INSTRUCTIONS FOR MORE DETAILS.
4X #6-32 X 1-1/4" BHCS INPUT CABLE
OUTPUT POWER CABLE
B
C
ADDITIONAL OUTPUT POWER CABLE (NOT SHOWN) INCLUDED WITH DCPR.90 FOR USE WITH DS.CF19 AND DS.CFX DOCKS
12VDC POWER PLUG
7. INPUT CABLE MAY BE HARD-WIRED TO THE VEHICLE'S ELECTRICAL SYSTEM BY CUTTING OFF THE SUPPLIED INPUT CABLE CIGARETTE LIGHTER 12VDC POWER PLUG AND CONNECTING THE BLACK WIRE TO VEHICLE GROUND AND THE RED (OR WHITE) WIRE TO 12VDC. SEE POWER SUPPLY INSTALLATION INSTRUCTIONS FOR MORE DETAILS.
B
HARDWARE KIT CONTENTS:
A
ITEM #6-32 X 1-1/4" BHCS #6-32 X 1-1/4" SMS #6 FLAT WASHER 9/64" ID, 3/8" OD
DS.CFU1 INPUT POWER RECEPTACLE
WARNING: ALL LEDCO PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER, IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING LEDCO MOUNTING AND DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IN INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE OPERATING VEHICLE.
DRAWING NUMBER: MI-0019-IS-B SHEET 1 8
7
6
5
4
QTY 4 4 8
DATE
PRODUCT I.D.
DCPR.90.U
11-12-08
PRODUCT NAME
DS.CFU1/UT.X POWER SUPPLY PRODUCT DESCRIPTION
WEIGHT: (LBS)
DC TO DC POWER SUPPLY WITH MOUNTING TABS AND CIGARETTE LIGHTER INPUT PLUG MOUNTED TO THE DS.CFU1 DOCKING STATION 3
1.58
877-88-LEDCO REV. DATE www.ledco.net 04-28-09 2
1
A
8
7
6
5
4
2
3
1
INSTALLATION INSTRUCTIONS: D
1. PLACE 4X FLAT WASHERS UNDERNEATH THE DCPR.90 ON THE BOTTOM SURFACE OF THE UNIVERSAL TRAY AND LINE UP THE HOLES WITH THE SLOTS ON THE SUPPLY, AS SHOWN. THE DCPR.90 MAY BE INSTALLED ON EITHER SIDE OF TRAY, SO LINE THE SLOTS WITH THE DESIRED MOUNTING HOLES.
OUTPUT POWER CABLE
UNIVERSAL TRAY (UT.X) (NOT INCLUDED)
ADDITIONAL OUTPUT POWER CABLE (NOT SHOWN) INCLUDED WITH DCPR.90 FOR USE WITH DS.CF19 AND DS.CFX DOCKS
D
2. INSTALL THE 4X #6-32 X 1-1/4" SHEET METAL SCREWS AND FLAT WASHERS THROUGH THE SLOTS OF THE POWER SUPPLY INTO THE HOLES ON THE BOTTOM OF THE DOCKING STATION, AS SHOWN.
ALTERNATE MOUNTING HOLES
3. INSTALL SCREWS UNTIL HEAD OF EACH SCREW MAKES CONTACT WITH POWER SUPPLY. AFTER ALL SCREWS HAVE MADE CONTACT, TORQUE TO 8 10% INLBS. C
POWER SUPPLY
12VDC POWER PLUG
B
4. ROUTE CABLES WITH ADEQUATE SERVICE LOOP TO ALLOW FREE MOTION OF THE DOCK AND SECURELY STRAIN RELIEVE CABLES MAKING SURE THEY ARE CLEAR OF ALL MOTION DEVICES AND PINCH POINTS. SEE UT.X INSTALLATION SHEET FOR TIE WRAP AND WIRE ROUTING DIRECTIONS. 5. INSERT POWER SUPPLY OUTPUT CABLE CONNECTOR INTO LAPTOP POWER RECEPTACLE AND SECURE USING ZIP TIES INCLUDED WITH THE UT.X. 6. FULLY INSERT INPUT CABLE 12VDC POWER PLUG INTO VEHICLE CIGARETTE LIGHTER SOCKET. SEE POWER SUPPLY INSTALLATION INSTRUCTIONS FOR MORE DETAILS.
4X #6-32 X 1-1/4" SHEET METAL SCREW INPUT CABLE
8X #6 FLAT WASHER
7. INPUT CABLE MAY BE HARD-WIRED TO THE VEHICLE'S ELECTRICAL SYSTEM BY CUTTING OFF THE SUPPLIED INPUT CABLE CIGARETTE LIGHTER 12VDC POWER PLUG AND CONNECTING THE BLACK WIRE TO VEHICLE GROUND AND THE RED (OR WHITE) WIRE TO 12VDC. SEE POWER SUPPLY INSTALLATION INSTRUCTIONS FOR MORE DETAILS.
A
WARNING: ALL LEDCO PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER, IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING LEDCO MOUNTING AND DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IN INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE OPERATING VEHICLE.
DRAWING NUMBER: MI-0019-IS-B SHEET 2 7
6
5
B
HARDWARE KIT CONTENTS:
ITEM #6-32 X 1-1/4" BHCS #6-32 X 1-1/4" SMS #6 FLAT WASHER 9/64" ID, 3/8" OD
8
C
4
DATE
PRODUCT I.D.
QTY 4 4 8
DCPR.90.U
11-12-08
PRODUCT NAME
DS.CFU1/UT.X POWER SUPPLY
PRODUCT DESCRIPTION
WEIGHT: (LBS)
DC TO DC POWER SUPPLY WITH MOUNTING TABS AND CIGARETTE LIGHTER INPUT PLUG MOUNTED TO THE UT.X LAPTOP MOUNT 3
1.58
877-88-LEDCO REV. DATE www.ledco.net 04-28-09 2
1
A
