Transcript
Installation Instructions
TH-1040-CTS TH-1040-CTL TH-1040-CTSW TH-1040-CTLW
Ceiling Tilt Short Mount / Ceiling Tilt Long Mount Component Checklist Hardware False Ceiling Cover
Mounting Plate
Coach Screw (x4)
Nylon Anchor (x4)
Mounting Plate Cover
Tools Required: • • • • •
VESA Plate Power drill 7mm (¼”) drill bit 12mm (½”) masonry drill bit Phillips head screw driver 17mm (11/16”) Socket Wrench or Shifter
Pole Assembly
M4/5 Spacer (x4)
2.5/3/5mm Allen Key M4/5/10 Washer (x4 each)
M4x16/25mm (x4 each)
M5x16/25mm (x4 each)
M6x16/30mm (x4 each) M5/6 Spacer (x4)
(optional) Security Screw
Display Mounting Screws
Set Screw
IMPORTANT INFORMATION: ! ! ! !
IMPORTANT - Install Telehook 1040 Ceiling Tilt Mount (Short/Long) as per Installation Instructions. This product supports a maximum load of 25kg (55lbs). This product supports VESA mounting hole configurations 75x75mm, 100x100mm, 200x100mm, 200x200mm. The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components Check you have received all parts against the Component Checklist and Hardware above.
Step 3. Install Mounting Plate Cover
Step 2. Install Mounting Plate Masonry Ceiling
Nylon Anchor
Timber Ceiling
Mounting Plate
PUSH
OR
M10 Washer
Pole Assembly
Coach Screw
Using the Mounting Plate as a template, mark out and drill 4x Ø7mm (¼”) holes, Ø12mm (½”) for masonry ceilings, 70mm (2.75”) deep.
Mounting Plate Cover
Step 4. Attach Pole Assembly to Mounting Plate
TWIST
Step 5. Position Mounting Plate Cover
Set Screw Mounting Plate 3mm Allen Key
Pole Assembly
PUSH Mounting Plate Cover Pole Assembly
A. Screw Pole Assembly into Mounting Plate by twisting top half of the Pole Assembly only.
B. Insert Set Screw into the Mounting Plate to lock the Pole Assembly in position.
Step 6. Set Height of Pole C. Tighten the Socket Cap Screws (x2) to set the height.
A. Whilst supporting the lower half of Pole Assembly loosen the Socket Cap Screws (x2).
2.5mm Allen Key
ADJUST HEIGHT TIGHTEN FIRMLY
5mm Allen Key
Pole Joint Set Screw
Socket Cap Screw
B. Slide Pole Assembly to the desired height.
LOOSEN
Step 7. Attach VESA Plate to Display
D. If necessary, centralise the Pole Joint by tightening the Set Screws (x2) to suit.
Step 8. Attach Display to Pole Assembly
Mounting Screws
A. HOOK
TOP
Security Screw B. PUSH
VESA plate
Spacers
C. (optional) Once Display is attached, insert Security Screw using Phillips-head screwdriver
(optional, for recessed mounting holes)
Choose the appropriate mounting hardware to suit the Display.
Step 9. Cable Management
Step 10. Height Adjustment 5mm Allen Key
SLIDE
Cable Access Port Donut Socket Cap Screw
A. Feed cables down the Pole Assembly through the Cable Access Port.
B. Pull cables out from lower half of the Pole Assembly and connect to Display.
Step 11. Final Adjustment TILT
VESA Ball Mount Tension Plate at rear
A. Loosen Socket Cap Screws (x2) on the Donut.
Step 12. Install False Ceiling Cover CLICK
False Ceiling Cover PAN
PORTRAIT TO LANDSCAPE 3mm Allen Key
A. Pan, Tilt and Rotate the Display as required.
B. If necessary tighten the VESA Ball Mount by adjusting the Tension Plate. Using the 3mm Allen Key adjust screws evenly.
B. Slide the height of the Donut as required. Tighten Socket Cap Screws to lock.
PUSH
Lower Pole
If the Lower Pole hangs below a suspended ceiling, clip the False Ceiling Cover over the Lower Pole, and push up to the ceiling.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 29.09.11 ©
Installation Instructions
TH-1040-CT-DV
Additional Mount Accessory for TH-1040-CTS and TH-1040-CTL Component Checklist VESA Plate
Mount Head Accessory
Mount Head Rear
Hardware M6/8 Spacer (x4) Security Screw (optional) M4/5 Washer (x4)
NOTE: Phillips-head screwdriver not supplied
5mm/3mm Allen Keys (x1 each)
Display Mounting Screws
M5x16/25mm (x4 each)
M6x20 Socket M4x16/25mm M6x16/30mm (x4 each) Cap Screw (x2) M4/5 Spacer (x4) (x4 each)
IMPORTANT INFORMATION: ! ! !
IMPORTANT - Install Telehook 1040 Additional Mount Accessory as per Installation Instructions. This product is to be installed in conjunction with TH-1040-CTS and TH-1040-CTL Ceiling Mounts only. The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Install Mount Head Accessory on TH-1040-CTS or TH-1040-CTL Attach Mount Head Rear to Mount Head Accessory with Socket Cap Screws (x2).
5mm Allen Key Socket Cap Screw Mount Head Rear
Mount Head Accessory ATTACH Use the 5mm Allen Key supplied.
Socket Cap Screw
Refer to TH-1040-CTS/TH-1040-CTL Installation Instructions, Step 8. Attach VESA Plate to Display. Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 12.03.12 ©
