Transcript
INSTALLATION INSTRUCTIONS PARTS LIST
Accessory
Application
SECURITY SYSTEM (LX)
2010 ODYSSEY
Publications No.
AII 41835 Issue Date
JUNE 2009
Fuse (2 A)
Security System Attachment: P/N 08E55-SHJ-100 Control unit bracket
Fuse label
Accessory User's Information Manual Security harness
Unit kit (sold separately): P/N 08E51-SHJ-100 Control unit Flange bolt, 6 x 16 mm
Flange nuts, 6 mm
Security label
6 Wire ties Microphone
2 Wire ties with clip
Ground bolt
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 41835 (0906)
08E55-SHJ-1000-91
1 of 8
3.
TOOL AND SUPPLIES REQUIRED Phillips screwdriver
Remove the right side lower cover (one clip, one retaining clip, and one stud).
Flat-tip screwdriver Felt-tip pen Tape measure 10 mm Combination wrench
STUD
10 mm Socket Ratchet Eye protection (face shield, safety goggles, etc.) 3 mm and 8 mm Drill bit Drill
RIGHT SIDE LOWER COVER
Illustration of the Security System Installed on the Vehicle
4603010B
CLIP
4.
CLIP
Remove the left side lower cover (one clip, one retaining clip, and one stud).
STUD
SECURITY HARNESS UNIT
MICROPHONE CLIP
4319030B
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1.
Make sure you have the anti-theft code for the radio, and write down the radio station presets.
2.
Disconnect the negative cable from the battery.
2 of 8
CLIP
AII 41835 (0906)
LEFT SIDE LOWER COVER
4603021B
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
5.
Pull out the cup holder. Remove the four selftapping screws, and disengage the two retaining clips, then pull out the center lower cover toward you. Remove the clip from the vehicle’s harness, disconnect the two vehicle harness connectors, and remove the center lower cover.
CUP HOLDER
VEHICLE CONNECTORS
7.
Remove the left front door sill trim (three clips). LEFT FRONT DOOR SILL TRIM 3 CLIPS
VEHICLE HARNESS CLIP
4 SELFTAPPING SCREWS
4301210B
8.
CENTER LOWER COVER
Pull out the door opening trim at the left kick panel. Remove the left kick panel (three clips).
4603030B
2 CLIPS
6.
3 CLIPS DOOR OPENING TRIM
Remove the lower cover at the driver’s side (one self-tapping screw, seven clips, and three retaining tabs). VEHICLE HOSE VEHICLE CONNECTOR
LEFT KICK PANEL
4301221B
3 RETAINING TABS
DRIVER’S LOWER COVER 4319041B
7 CLIPS
SELF-TAPPING SCREW
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 41835 (0906)
3 of 8
Routing the Security Harness 9.
10. Secure the security harness to the vehicle harness with one wire tie.
Plug the security harness 6-pin connector into the fuse box 6-pin connector.
VEHICLE HARNESS WIRE TIE
SECURITY HARNESS
SECURITY HARNESS
SECURITY HARNESS 6-PIN CONNECTOR
4319070B
11. Route the ground terminal from the security harness down below the fuse box.
FUSE BOX 4319050B
NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the other accessory harness and plug the security harness into that connector.
SECURITY HARNESS
FUSE BOX OTHER ACCESSORY HARNESS 6-PIN CONNECTOR
GROUND BOLT
DUMMY CONNECTOR BOLT (Discard.) SECURITY HARNESS 6-PIN CONNECTOR
4 of 8
HOOD OPENER 4319060B
SECURITY HARNESS GROUND TERMINAL
4319080B
12. Remove and discard the upper hood opener bolt. Get the ground bolt from the kit, and install the ground bolt with the security harness ground terminal to secure the upper hood opener.
AII 41835 (0906)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
13. Secure the ground terminal from the security harness to the vehicle harness with two wire ties.
15. Continue routing the security harness along the vehicle frame, and secure it with one wire tie. Wrap one wire tie with clip around the security harness and attach the wire tie with clip to the hole in the vehicle frame.
SECURITY HARNESS
WIRE TIE
WIRE TIE WITH CLIP HOLE IN VEHICLE FRAME
VEHICLE HARNESS
VEHICLE FRAME
SECURITY HARNESS
SECURITY HARNESS GROUND TERMINAL
WIRE TIES 4319090B
14. Route the security harness up along the vehicle harness, and secure it to the vehicle harness with one wire tie.
4319110B
Installing the Control Unit 16. Install the control unit bracket to the hole in the vehicle frame using the 6 x 16 mm flange bolt and flange nut.
VEHICLE HARNESS WIRE TIE
SECURITY HARNESS
HOLE IN VEHICLE FRAME
6 mm FLANGE NUT
CONTROL UNIT BRACKET
6 x 16 mm FLANGE BOLT 4319120B
4319100B
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
AII 41835 (0906)
5 of 8
17. Install the control unit to the control unit bracket.
21. Route the microphone cable through the hole in the driver’s lower cover, and seat the microphone flush in the cover.
CONTROL UNIT BRACKET
DRIVER’S LOWER COVER MICROPHONE
MICROPHONE JACK
CONTROL UNIT SECURITY HARNESS 18-PIN CONNECTOR
4319130B
DRIVER’S LOWER COVER MICROPHONE
18. Plug the security harness 18-pin connector into the control unit. Installing the Microphone 19. On the back of the driver’s lower cover, measure and mark the cover using a felt-tip pen at the measurements shown.
22. Attach a wire tie clip the microphone cable at the indicated position.
DRILL (First drill with a 3 mm drill bit, and finish with an 8 mm drill bit.)
FELT-TIP PEN DRIVER’S LOWER COVER
4319151B
30 mm WIRE TIE WITH CLIP
200 mm
MICROPHONE JACK
13 mm DRIVER’S LOWER COVER
26 mm
4319161B
MARK DRIVER’S LOWER COVER 4319141B
20. While wearing eye protection, drill an 8 mm hole through the marked location. First drill with a 3 mm drill bit, then finish with an 8 mm drill bit. Remove any burrs.
6 of 8
AII 41835 (0906)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
23. While holding the driver’s lower cover near the dashboard, attach the wire tie with clip into the vehicle bracket.
26. Install the 2 A fuse in the fuse box in the location shown. FUSE BOX
MICROPHONE JACK
CONTROL UNIT 2 A FUSE
WIRE TIE WITH CLIP
DRIVER’S LOWER COVER
2219080T 4319171B
27. Attach the 2 A fuse label to the No. 33 slot on the fuse box cover.
24. Plug the microphone jack into the control unit. 25. Bundle the excess microphone cable, and secure the excess cable to the security harness with one wire tie. MICROPHONE CABLE (Bundle the excess length.)
SECURITY HARNESS
FUSE LABEL (OPTION FUSE 2 A)
FUSE BOX
WIRE TIE
No. 33
2219090T
DRIVER’S LOWER COVER
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
4319181B
AII 41835 (0906)
7 of 8
28. Check that all wire harnesses are routed properly and all connectors are plugged in. 29. Reinstall all removed parts. 30. Reconnect the negative cable to the battery. 31. Enter the customer’s radio anti-theft code, and reset the radio station presets. 32. Reset the clock. 33. Check operation of the security system according to the security system owner’s manual provided. NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled. 34. Start the engine. Push down on the driver’s window switch until the window is fully open, then hold the switch for 2 seconds or more. 35. Pull up on the driver’s window switch to close the window completely, then hold the switch for 2 seconds or more. 36. Test the AUTO window function.
8 of 8
AII 41835 (0906)
© 2009 American Honda Motor Co., Inc. - All Rights Reserved.
