Transcript
Installation Instructions TIMES SQUARE™
T184.50X Series
PRESSURE BALANCING BATH AND SHOWER TRIM KITS
H
C FFO
H
C FF O
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1
M965471 Rev. 1.1
Recommended Tools Phillips Screwdriver Adjustable Wrench Plumbers' Putty or Caulking
Teflon Tape
Channel Locks
Flat Blade Screwdriver
ROUGHING-IN DIMENSIONS (For reference only) To assure proper positioning in relation to wall, note roughing-in dimensions.
65mm (2-1/2" Sq.)
102mm (4")
SWEAT INLETS
1-5/8" TO 3-1/4" (41 mm TO 83 mm)
305mm (12")
1/2" NPT
2" (51mm)
OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' (1651mm) AND 80'' (1880mm)
203mm SQ. (8")
4-1/16" (103mm)
TUB 1/2" NOM. COPPER SWEAT
SWEAT INLETS (STOPS)
7-1/2" REF. (191 mm)
FINISHED WALL 74" FOR HEAD CLEARANCE (188 cm)
INLETS 1/2" NOM. COPPER SWEAT
SHR. 1/2" NOM. COPPER SWEAT
65mm (2-1/2" Sq.)
4-1/2"REF. (114 mm)
1/2" NPT
INLETS 4-1/16" (103mm)
5-7/8" (149mm)
SHR. 1/2" NOM. COPPER SWEAT
4-1/16" (103mm)
TUB 1/2" NOM. COPPER SWEAT INLETS 1/2" NOM. COPPER SWEAT
"SEE ILLUSTRATION"
8-1/4" (210 mm) SHR
3-3/8" (98mm) OUTLETS 1/2" NPT
TUB
18" OPTIONAL (457mm) 4-3/4" REF. (121mm)
INLETS 1/2" NPT 3-3/8" (98mm)
1/2" COPPER 4" (102 mm) TOP OF TUB RIM BOTTOM OF TUB
1-3/4" MIN. (44 mm)
5-7/8" (149mm) INLETS 1/2" NPT
3-3/8" (98mm) OUTLETS 1/2" NPT
THREADED INLETS
THREADED INLETS (STOPS)
1
INSTALL VALVE TRIM Figure 1. Remove plaster guard from valve. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. Figure 2. Make sure O-RING (8) is secure within ESCUTCHEON HOLDER (3). Push ESCUTCHEON HOLDER (3) onto CAP (1) and attach with LONG SCREWS (4). Mount ESCUTCHEON SUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORT SCREWS (6).
PLSTER GUARD
1
2
Figure 1.
Figure 3. Install ESCUTCHEON (7) onto CAP (1) and push flush against finished wall. Escutcheon (7) will snap fit onto ESCUTCHEON SUPPORT (5).
1 3 8
7 5 5
Figure 2.
4
1
Figure 3.
6
2
INSTALL, TUB SPOUT, SHOWER HEAD, SHOWER ARM WITH FLANGE AND HANDLE
2 2
Remove pipe cap and plug from shower and tub rough piping.
3
SHR. ELBOW
HEX WRENCH
3
Install TUB SPOUT (1) onto tub nipple. CAUTION: Protect finish on TUB SPOUT when installing. Install SHOWER ESCUTCHEON (2) onto SHOWER ARM (3). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (3) and thread longer leg of SHOWER ARM (3) into shower elbow.
HEX WRENCH
PIPE PLUG
4
4
Thread SHOWER HEAD (4) onto SHOWER ARM (3). CAUTION: Protect finish on SHOWER HEAD and ARM when installing. Install HANDLE (5) onto CARTRIDGE STEM (6). Tighten SET SCREW (7) with HEX WRENCH (8) supplied.
5 7 8
PIPE CAP
6
TUB FILLER NIPPLE
1-3/4" MIN.
1 HEX WRENCH
M965471 Rev. 1.1
2 0
4
97531
By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1).
3 311
ADJUST HOT LIMIT STOP
5
15 1
1 3
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use aflat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise one number to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1) for indication.
2 1
3 1 5 1 1
9 7 5 3
TO GAIN ACCESS TO VALVE FOR SERVICING
1
4
HOTTER (Smaller Numbers) 0 1 3 5 7 9 11 13 15
5 Remove HANDLE (see step 2 and reverse).
1 3 1
1 9 7 5 3
4
1
Remove ESCUTCHEON and CARRIDGE CAP (see step 1 and reverse). Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve.
15
3
COLDER (Larger Numbers) 0 1 3 5 7 9 11 13 15
1
VALVE LEAKS WHEN SHUT OFF Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and pull out PRESSURE BALANCING (5) unit. Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8). Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws. Turn on water supply and see above for installing TRIM and HANDLE. UNABLE TO MAINTAIN CONSTANT TEMPERATURE Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly. Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair Part M952100-0070A if balancing unit is defective. Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting. Top flange should butt-up against top of casting. BACK TO BACK INSTALLATION Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the large outlet port faces down. Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should butt up against top of casting. Reassemble FIXATION RING (4) and CARTRIDGE (1).
4
ROTATE 180˚
1
8
5
LARGE OUTLET
5
7 6
5
3
INLETS
9
2
BACK TO BACK INSTALLATION
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M965471 Rev. 1.1
TIMES SQUARE™ PRESSURE BALANCING BATH AND SHOWER TRIM KITS
M907633-YYY0A SHOWER ARM FLANGE
MODEL NUMBER
T184.50X Series
M919631-YYY0A SHOWER ARM
M907633-YYY0A SHOWER ARM FLANGE A919542-YYY0A SHOWER ARM 1660688.YYY SHOWER HEAD
M953568-YYY0A SHOWER HEAD
M907698-YYY0A ESCUTCHEON M962642-0070A ESCUTCHEON HOLDER
M907053-YYY0A CAP
H
C OFF
M961818-YYY0A DEEP ROUGH KIT (NOT SHOWN) M962848-YYY0A HANDLE KIT
Replace the "YYY" with appropriate finish code CHROME SATIN NICKEL
002 295
M950329-YYY0A DIVERTER SPOUT (SLIP-ON) HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN MEXICO 01-800-839-1200 IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2013
M965471 Rev. 1.1
