Transcript
Wireless Alarm Upgrade Kit 754RFKIT With Programmable Alert Tones
®
Installation Instructions Please leave these instructions at the installation site.
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
Contents 1.0
Introduction .............................................................................................. 3
2.0
Installation Procedure ............................................................................. 4 2.1 Install the RF Transmitter Module..................................................... 4 2.2 Select a Location for the Chime Receiver ........................................ 4 2.3 Install the Chime Receiver Batteries ............................................... 4
3.0
Operation and Testing ............................................................................. 5 3.1 Power On Demonstration .................................................................. 5 3.2 Linking the Transmitter & Receiver ................................................... 5 3.3 Changing the Sound Selection ......................................................... 6 3.4 Sound Volume Adjustment................................................................ 6 3.5 Low Battery Indication ...................................................................... 6 3.6 Snooze Function ............................................................................... 6 3.7 Resetting / Erasing Programmed Parameters.................................. 7 3.8 Linking Multiple Transmitter Units to a Single Chime Receiver Unit ..... 7 3.9 Linking Multiple Chime Receiver Units ............................................. 7
4.0
Troubleshooting ....................................................................................... 8
5.0
Technical Specifications ......................................................................... 8
6.0
Warranty ................................................................................................. 9
7.0
Technical Support .................................................................................... 9
9.0
Product Range ....................................................................................... 12
2 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
1.0 Introduction Thankyou for purchasing the 754RFKIT Wireless / RF Upgrade Kit. RF Chime Receiver Unit
The upgrade kit is intended to be used in conjunction with the Clipsal 754 Series Infrascan Outdoor Motion Sensor product range only. The unit is a wireless alarm that is designed to emit an audible alert in response to movement detected by the motion sensor. The unit is battery powered and retrofittable – no extra wiring is required. Simply plug in the RF Transmitter, and the portable Chime Receiver Unit will automatically alert you to any external activation of the 754 Series Motion Sensor.
RF Transmitter Module
Features: •
Wireless / RF Accessory Kit
•
Retrofittable Upgrade to suit 754 Series Motion Sensors
•
Six User Selectable Alert Tones when PIR Detects Motion (Including various Chimes, Knock-Knock, Sonar, Barking Dog)
•
Snooze Function Incorporated
•
100metre Wireless Transmission Range, 433MHz
•
Battery Operated (3xAA Cell, not included)
•
Indoor Use Only
Note: The upgrade kit is intended to be used in conjunction with the Clipsal 754 Series Infrascan Outdoor Motion Sensor product range only. Please refer to the back page of this instruction booklet for an overview of models available.
© Clipsal Australia Pty Ltd
3 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
2.0 Installation Procedure 2.1 Install the RF Transmitter Module 1. Isolate power from your 754 Series Outdoor Motion Sensor. 2. Remove the rubber bung from the underside of the detector. 3. Insert the RF Transmitter Module into the connection socket. 4. Turn the mains power back on to the sensor. 5. The unit will then go through the warm-up sequence and the Transmitter will automatically begin to transmit a signal.
RF Transmitter Installation
2.2 Select a Location for the Chime Receiver 1. Position the Chime Receiver Unit in the desired location up to 100 metres away from the RF Transmitter. Take into account the path between the Transmitter and Receiver – line of sight is not required, however it is important to note that objects in between may reduce the maximum transmission distance achievable. Metallic objects shield RF signals and should be avoided. 2. The Chime Receiver can be placed anywhere within the home. It can be used purely as a free-standing mobile sounder, or it can be fixed in a permanent position by using the wall mounting bracket supplied.
2.3 Install the Chime Receiver Batteries 1. Unclip the battery compartment on the bottom of the Chime Receiver Unit. 2. Insert 3 x AA batteries (not supplied). 3. Replace the battery compartment cover. 4. Installation is complete!
4 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.0 Operation and Testing 3.1 Power on Demonstration 1. When the batteries are first inserted the Chime Alert Unit will cycle through the available sounds. Sounds Options: Ding Dong ➔ Sonar Sound ➔ Knock Knock ➔ Barking Dog ➔ Alarm / Siren 2. You can press one of the buttons at any time to stop the demonstration.
3.2 Linking the Transmitter and Receiver 1. Ensure that the power to the Motion Sensor unit that has the Transmitter fitted to it is switched ON. 2. Activate the Motion Sensor so that the Transmitter will broadcast a signal. 3. The Chime Receiver should respond with the Ding Dong sound, and the red LED will blink quickly as indication that the Motion Sensor is communicating with it. 4. Activate the Motion Sensor a few more times to ensure that the Chime Receiver is responding reliably, and has good RF reception with the Transmitter. 5. You can choose to leave this sound selection (Ding Dong), or change it to a desired sound by pressing the “NOTE” button to scroll through the available sound options. 6. At the required sound, press the “TOOL” button for more than 1 second to select that sound, and exit from Programming Mode. A single “bi” tone will be heard indicating that the programmed tone has been successfully changed. The unit is now in Normal Mode and is ready for use.
RF Chime Receiver Unit
© Clipsal Australia Pty Ltd
5 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.3 Changing the Sound Selection 1. Enter Programming Mode by pressing the “TOOL” button for more than one second. A triple “bi” tone will be heard to indicate that the Chime Receiver is ready for programming. 2. To alter the selected sound, first activate the RF Transmitter programmed to the sound you wish to change. 3. When the Chime Alert sounds, press the “NOTE” button to scroll through the available sound options. 4. At the required sound, press the “TOOL” button for more than 1 second to select that sound, and exit from Programming Mode. A single “bi” tone will be heard indicating that the programmed tone has been successfully changed. The unit is now in Normal Mode and is ready for use.
3.4 Sound Volume Adjustment 1. While in Normal Mode, you can adjust the volume by pressing the “NOTE” button. 2. The Chime Alert will play the currently selected sound, and scroll through 4 volume levels plus one “No Sound” option. The No Sound option is indicated by the red LED blinking upon activation.
3.5 Low Battery Indication 1. While in Normal Mode, you can adjust the volume by pressing the “NOTE” button. 2. The Chime Alert will play the currently selected sound, and scroll through 4 volume levels plus one “No Sound” option. The No Sound option is indicated by the red LED blinking upon activation.
3.6 Snooze Function 1. The Chime Alert incorporates a “Snooze” Mode, which is designed to mute the unit for a period of one hour. 2. Press and hold the “NOTE” button for more than one second and a “snooze” sound will be heard. 3. Within this one hour period, the Chime Alert will not respond to the RF Transmitter, and will not make any sounds. 4. Press any button on the Chime Alert to cancel Snooze Mode and resume Normal operation.
6 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
3.7 Resetting / Erasing Programmed Parameters To reset the Chime Receiver and erase all memorized RF Transmitters, just press and hold the “TOOL” button for more than 5 seconds until the Ding Dong sound and further sounds are played. Once all tones have played, all Transmitter links to that Receiver have been erased.
3.8 Linking Multiple Transmitter Units to a Single Chime Receiver Unit Each Chime Receiver is capable of responding to multiple Transmitter Modules. This is useful if you have a number of Motion Sensors throughout the installation, and require a single Chime Unit to alert the occupant of movement. For example, you can have a Motion Sensor at the front door and another at the back door, both of which communicate with a single Chime Receiver. The Chime Receiver has a default sequence for additional Transmitters linked to it: Transmitters Linked 1st
Ding Dong
2nd
Sonar Sound
3rd
Knock Knock
4th
Barking Dog
5th
Barking Dog
6th
Barking Dog
A maximum of SIX RF Transmitters can be linked to each Chime Receiver. To link additional RF Transmitter units to the Chime Receiver, follow the procedure described in Section 3.2, and repeat for each additional Transmitter. Be sure to activate only ONE Transmitter at a time. If necessary, switch power to other 754 Series Motion Sensors OFF whilst programming.
3.9 Linking Multiple Chime Receiver Units Multiple Chime Receiver units can be programmed to respond to each Transmitter. This might be useful in a larger house, where you may not be able to hear the Receiver tone from the other end of the house. To link another Chime Receiver, repeat the steps described in Sections 3.2 and 3.8 until all Transmitters and Receivers have been link as required.
© Clipsal Australia Pty Ltd
7 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
4.0 Troubleshooting PROBLEM
SOLUTION
Chime does not activate
Ensure the batteries are fitted correctly.
Cannot program chime
Check that the transmitter unit has power and the sensor has been activated. Ensure the RF transmitter is correctly and securely fitted in the light unit. Following the instructions in Section Four, reset the Chime Alert by deleting all programing and follow the steps through again.
PIR sensor did not operate at all
Refer to the Troubleshooting Guide provided with your Clipsal 754 Series Motion Sensor.
5.0 Technical Specifications RF Transmitter Power Supply
3.3V d.c. Transmitter
Module Mode
AM O.O.K (ON.OFF.KEY)
Maximum Switchable Load
N/A
Transmission Frequency
433.92 MHz
Tramsmitter Max Power
2dBm
Transmission Range
Up to 100m (varies with surrounding structures)
RF Chime Unit Power Supply
4.5V d.c. (3 x ‘AA’ Batteries)
Reciever Frequency
433.92 MHz Specifications Typical 25°C No User Servicable Parts Inside
This Product is Recommended for INDOOR USE ONLY
8 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
6.0 Warranty 1. The benefits conferred herein are in addition to, and in no way shall be deemed to derogate; either expressly or by implication, any or all other rights and remedies in respect to the Clipsal Product, which the consumer has under the Commonwealth Trade Practices Act or any other similar State or Territory Laws. 2. The warrantor is Clipsal Australia Pty Ltd of 12 Park Terrace Bowden, South Australia 5007. Telephone (08) 8269 0511. With registered offices in all Australian States. 3. This Clipsal Product is guaranteed against faulty workmanship and materials for a period of two (2) years from the date of installation. Warranty excludes any user replaceable parts. 4. Clipsal Australia Pty Ltd reserves the right, at its discretion, to either repair free of parts and labour charges, replace or offer refund in respect to any article found to be faulty due to materials, parts or workmanship. 5. This warranty is expressly subject to the Clipsal Product being installed, wired, tested, operated and used in accordance with the manufacturer’s instructions. 6. All costs of a claim shall be met by Clipsal Australia Pty Ltd, however should the product that is the subject of the claim be found to be in good working order all such costs shall be met by the claimant. 7. When making a claim the consumer shall forward the Clipsal Product to the nearest office of Clipsal Australia Pty Ltd with adequate particulars of the defect within 28 days of the fault occurring. The product should be returned securely packed, complete with details of the date and place of purchase, description of load, and circumstances of malfunction.
7.0 Technical Support For all technical enquiries and assistance please contact our
National Customer Service Enquiries Hotline Tel 1300 2025 25 Fax 1300 2025 56 (Call cost 25c, number valid within Australia only)
© Clipsal Australia Pty Ltd
9 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
8.0 Notes ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ 10 of 12
© Clipsal Australia Pty Ltd
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
8.0 Notes ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ © Clipsal Australia Pty Ltd
11 of 12
754RFKIT
Wireless Alarm Upgrade Kit Installation Instructions
9.0 Product Range The following products are also available in the 754 Series:
754HL1/140/150
150W Security Floodlight 140° Passive Infrared Outdoor Motion Detector Complete with 150W R7s Linear Halogen Floodlight
754HS1/140/60
60W Security Spotlight 140° Passive Infrared Outdoor Motion Detector Complete with Single 60W G9 High Efficiency Halogen Spotlight
754HS2/140/60
60W Security Twinspot 140° Passive Infrared Outdoor Motion Detector Complete with Twin 60W G9 High Efficiency Halogen Spotlights
754HF1/180/150
150W Security Floodlight 180° Passive Infrared Outdoor Motion Detector Complete with 150W R7s Linear Halogen Floodlight
754HF1/180/300
300W Security Floodlight 180° Passive Infrared Outdoor Motion Detector Complete with 300W R7s Linear Halogen Floodlight
754HB1/180/60
60W Security Spotlight 180° Passive Infrared Outdoor Motion Detector Complete with Single 60W G9 High Efficiency Halogen Spotlight
754HB2/180/60
60W Security Twinspot 180° Passive Infrared Outdoor Motion Detector Complete with Twin 60W G9 High Efficiency Halogen Spotlights
Product of Clipsal Australia Pty Ltd A member of Schneider Electric
clipsal.com
Telephone (08) 8269 0511 Facsimile (08) 8340 1724 Contact us clipsal.com/feedback National Customer Service Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
Clipsal Australia Pty Ltd reserves the right to change specifications, modify designs and discontinue items without incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be liable for any error therein. © Clipsal Australia Pty Ltd.The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted. F2109/01
CLIPCOM 15883 May 2008
