Transcript
Installation Manual WPS-MNT-L-DOM Dome Camera L Mount
Introduction Wirepath™ Surveillance Camera Mount Plates have been designed to simplify installation and overcome the complexity of concealing connections when installing Wirepath™ Surveillance cameras. Each mount fits a variety of interior and exterior junction box sizes providing flexibility during installation. • Single • Double • 4” Square
Installation Guidelines Mounting
When mounting to a junction box, we recommend the use of metal junction boxes, doing so will provide the most secure installation.
Weatherproofing
While grommets and gaskets are provided to help block out moisture, we recommend adding a bead of silicone around the edges of the mount for outdoor installations. This will help ensure that moisture will not enter the wall.
Parts Included
Exploded View A. (1) Camera Mount B. (1) L Mount
Exploded View
D
C. (1) L Mount Gasket D. (1) Wall Plate Adapter Note: Make note of this diagram and letters as they are used later in this document.
Not Shown
C B A
E. (2) M5x12L Round Head Philips F. (2) M5x8L - Hex Thumb Screw G. (2) #6-32x3/4”L - Flat Head Philips H. (2) #8-32x3/4”L - Flat Head Philips I. (4) M3x4 Pan Philips Head J. (4) M6x20L Round Philips Head K. (4) M6x20L Tab Fastner L. (3) M4x10L - Round Head Philips with Rubber Washers M. (1) Manual
© 2012 Wirepath™ Surveillance
pg. 1
WPS-MNT-L-DOM Installation Manual
Installation Important Note: To avoid damaging the dome surface during installation, keep the dome surface away from walls and other objects. Do not remove the protective coating from the dome until after the camera is mounted and the dome installed. Microfiber or similar cloths can be abrasive, only use a dry eyeglasses cloth when cleaning the lens to avoid damage that can blur the cameras image.
1. Install the Camera Wires into the Mount and Arm A. Remove the Camera Mount Plate (A) from the L Bracket (B). Set the L Mount to the side.
Figure 1
B. Insert the wires from the camera through the wire hole in the Camera Mount Plate (A) and through the hole in the L Mount (B) pulling out of the rear of the L Mount. Tip: Placing the BNC Video Out in first makes the process quick
C. Secure the Camera Mount Plate (A) to the L Mount (B) using the 4 M3x4 Pan Head screws (I); ensure that it is fully tightened. 2. Attach the Camera to the Mount A. Remove the dome from the Camera Base using the 3mm Allan key supplied with the camera. Avoid contact of the dome with surfaces in order to avoid scratching the dome material.
Figure 2
Align Holes*
B. Place the Camera Base on the Camera Mount Plate (A) orientated as shown in Figure 2. Tip: Inserting a mounting screw into the Camera Base and then into the Camera Mount speeds up the alignment process.
C. Secure the Camera Base to the Camera Mount Plate using all 3 provided M4x10L Round Head Philips (L) screws with rubber washers.
Camera Base
Camera Conduit Connection
Camera Mount (bottom) *Note orientation of Camera Base and Camera Mounting Plate. Identified holes must line up.
Note: To avoid moisture from entering the camera; ensure that the rubber grommets are on the screws during installation
D. Loosely attach the dome onto the Camera. Note that you need to remove this later to setup the camera once it is fully mounted. The assembly is now ready to be mounted to the wall.
pg. 2
www.snapav.com Support: 866.838.5052
WPS-MNT-L-DOM Installation Manual
3. Attach the Wall Plate Adapter to the Wall Plate Mounting Holes The Wall Plate Adapter included with the mount is designed to fit a variety of junction box sizes. • Single • Double • 4” Square The diagram below identifies which holes to use when mounting to the various plates.
C
B
A
B
D
E
E
A. Single Gang B. Double Gang C. 4” Square D. 4” Square (If 4” Square Box is rotated) E. L Mount Alignment Posts F. L Mount Lower Screws
F D
F B
A
B
C
A. Pull the wires from the wall through the center hole in the Wall Plate Adapter. B. Align the Wall Plate Adapter mounting holes with the holes on the Junction Box and secure the Wall Plate Adapter.
Figure 3
Note: While a Single Gang box is shown, the plate contains mounting holes for various types of
Single Gang Junction Box
Junction Boxes or Masonry wall.
C. Secure the Wall Plate Adapter to the Wall Plate Adapter. Note that the screws are different depending on the junction box.
© 2012 Wirepath™ Surveillance
Wall Plate
pg. 3
WPS-MNT-L-DOM Installation Manual
4. Attach the L Mount / Camera Assembly to the Wall A. Place the L Mount Gasket on the rear of the L Mount with the groove towards the mount and the tab lined up with the slot on the mount. B. Place the L Mount (B) assembly onto the Wall Plate Adapter (D) aligning the Alignment Post (Figure 4) with the upper right mount screw location on the L Mount (B). C. Loosely insert the one of the M5x8L Hex Thumb Screws (F), this will allow for the assembly to swing down and be supported while the connections are made. (Figure 5)
Figure 4
Figure 5
Alignment Post M5x8L Hex Thumb Screw (F) D. Connect the wires from the wall to the Cameras wires at the end of the L Mount assembly and tuck the wires into the junction box or wall. E. Swing the assembly clockwise (Figure 5), aligning the upper left hand screw with the alignment post on the Wall Plate Adapter. Insert the remaining M5x8L Hex Thumb Screw (F), tighten, and insert the M5x12L Round Head Philips (E) into the lower mounting holes. F. Tighten all screws. 5. Finalize the Installation (outdoor cameras) For outdoor installations, we recommend adding a bead of silicone around the edges of the mount. This will help ensure that moisture will not enter the wall. 6. Setup the Camera Now that the camera is mounted, it can be setup for angle, zoom, and focus. Follow the instructions in the manual for the Wirepath™ Surveillance camera that has been installed.
Contacting Technical Support Phone: (866) 838-5052 Email:
[email protected]
© 2012 Wirepath™ Surveillance 120829-1455
