Transcript
INSTALLATION MANUAL
© 2006 Telesis A.Ş. V1.0
INSTALLATION MANUAL Thank You ...for purchasing the STILLINK 200 digital VOIP gateway/signaling converter. It is manufactured to the highest quality standards and tested vigorously to comply with requirements for its product specifications. In the following pages you will find basic information about quickly setting up your system. We hope that this simplified introduction will get you started and help you familiarize yourself with your new equipment. You can find more information about programming and advanced features in the help documentation supplied with your system. We hope that the STILLINK 200 will serve you well and provide you with all your telecommunication needs in the years to come.
Telesis A.Ş. Ankara/TURKEY TECHNICAL SUPPORT tel: +90 312 384 0394 email:
[email protected] web: www.stillink.com
2
INSTALLATION MANUAL SAFETY FINDING A SUITABLE SITE FOR INSTALLATION The installation site should be bright enough for ease of operation to the installation personnel. The 220V mains connection should be grounded, power should not be interrupted except for power outages. The ambient enviromental conditions should be within the range of: Temperature range: Humidity range:
0- 40°C 20-85%
Ensure that the installation site does not contain: • • • • •
High voltage lines, smoke, dust, gas or radiation (such as a generator, photocopier etc.) Radio equipment that generates or emits high frequency signals Sever, pipes or valves that could leak or cause condensation Vibration causing equipment Exposure to heat sources or direct sunlight
GROUNDING To ensure long operational life to your system and your safety, all electrical components should be suitably grounded. • • •
•
A protective, independent ground terminal should be connected The resistance of the ground and neutral terminals should not exceed 0.5 Ω The 220V outlet that connects to the the system`s power supply should provide phase-ground and phase-neutral voltage difference no more than 5V Any auxilliary equipment that is connected to STILLINK 200 (such as a printer or a maintenance PC terminal) should use the same ground as your system.
POWER 90 – 264VAC @ 47-63Hz 240VAC 0.25A @ 50Hz PHYSICAL DIMENSIONS 255 x 220 x 77 mm (wxdxh) 3.2 kgs
3
INSTALLATION MANUAL WARNINGS This product should be installed and serviced only by qualified personnel who have necessary training about electrical equipment, and who understands the hazards that can arise when working on this type of equipment. Equipment needs to be grounded with a suitable ground terminal before installation. The ground cable should be routed to ensure that it is as short as possible. Protective ground should not be connected to the ground terminal of any other equipment (i.e. Lightning or transformer ground). External lines or outside lines that could be exposed to enviromental conditions should be protected with secondary protective circuitry. To minimize the risk of electrostatic damage to the equipment, serviceman should discharge of electrostatic buildup by wearing a shielding bracelet or take necessary actions before handling electrostatic sensitive parts such as cards. This equipment is to be used in controlled environments where humidity and ambient temperature is maintained within working specifications (Temperature range: 0-40, Humidity range: %2085) and necessary precautions should be taken before leaving the equipment unattended). Disconnect all power sources from the equipment before servicing.
Do not plug or unplug the maintenance PC connection from the STILLINK 200's COM port while it is in operation.
Any auxilliary equipment that is to be connected to STILLINK 200 should be set up according to its installation procedure.
4
INSTALLATION MANUAL INTRODUCTION With a capacity of dual E1 interfaces that allow connections to the PSTN with SS No. 7, V5.2, DSS1 Euro ISDN, QSIG, R1, R2, CL1B, OCL-1B, TCL-1B, CL-1VF, OCL-1VF, TCL-1VF, SL/ZSL, SLM, and other CAS signaling and an ethernet interface for VoIP calls, the STILLINK 200 is the perfect and cost effective solution if you are looking into updating an existing telecommunications network, migrating to the VoIP technology or building a network that is ready for the future. The STILLINK 200 is capable of making signaling conversion among its E1 interfaces as well as routing TDM calls to VoIP calls and vice versa. The STILLINK 200 is a unique solution with its capabilities such as: • • • • •
Digital VoIP gateway with PSTN by-pass (both H.323 and SIP protocol support) Single E1 span signaling conversion Integrated and advanced TDM signaling analyzer Integrated H.323 gatekeeper Integrated SIP registrar
The all-protocol switching capability and advanced routing features contained in the STILLINK 200 represent a bridge to today’s heterogeneous networks. The STILLINK 200 is fully non-blocking and can handle high call volumes without congestion. Internal routing tables are configured via the user-friendly MML, XMan™, which provides flexible E1 signaling conversion management. It provides 15 or 30 simultaneous VoIP channels for IP to TDM call routing and vice versa. The STILLINK 200 with dual E1 interfaces provides solutions for: • • •
15 or 30 VoIP gateway channels as well as SS No.7 - ISDN (NT or TE configurable DSS1, QSIG) signaling conversion 15 or 30 VolP gateway channels as well as SS No.7 - CAS (R1, R2, CIS, E&M) signaling conversion 15 or 30 VoIP gateway channels as well as ISDN (NT or TE configurable DSS1, QSIG) - CAS (R1, R2, CIS, E&M) signaling conversion
The STILLINK 200 is ideal for customers who seek a cost effective solution for both signaling support for the PSTN connection and VoIP migration.
5
INSTALLATION MANUAL HARDWARE System Pins for the Status maleLED: D-SUB When COMthe portsystem (Aux) connector is operating arethe shown green in Figure LED status 4. blinks periodically. Reset For E1button: interfaces This RJ-45 button type is connector to start theissystem used. The with pins the default for the RJ-45 type connector parameters. When the aresystem shown in is Figure powered 5. up with this button pressed hold, the system starts with the default parameters instead of the user defined parameters. To upload the default 6 parameters to the system the reset button must be hold pressed until the system status LED starts blinking periodically. Reset LED: The red LED indicates that the reset button is pressed. COM port: This port is used in connecting to a maintenance PC running XMan™. A proprietary cable is used for the connection. 10/100 Ethernet port: This port is used for ethernet connectivity for VOIP applications and for maintenance purposes. E1 ports: E1 interface ports over a RJ-45 connector. Figure 1. STILLINK 200 front fascia
Com port
Reset button E1 ports
System status LED
Reset LED
10/100 Ethernet port
6
INSTALLATION MANUAL HARDWARE Your system is equipped with a universal power supply. For operation simply plugging in the power cord to an outlet is sufficient. Before connecting the system to a wall power outlet make sure the protective ground connection is attached first. Similarly, when disconnecting the system from its power source make sure the protecting ground stays attached as the last connection to be detached from your equipment.
Figure 2. STILLINK 200 rear fascia
Mains switch
Socket to wall power outlet
Protective ground connector knob
7
INSTALLATION MANUAL HARDWARE Pins for the male D-SUB COM port (Aux) connector are shown in Figure 3. For E1 interfaces RJ-45 type connector is used. The pins for the RJ-45 type connector are shown in Figure 4.
Figure 3. Pins for the male D-SUB COM port connector.
Figure 4. Pins for the RJ-45 connector.
Pins
Desc
1
Receive
2
Receive
4
Transmit
5
Transmit
The other pins are N/A
8
INSTALLATION MANUAL SOFTWARE The STILLINK 200 maintenance software XMan™ runs under the Microsoft Windows™ operating system and is the main interface for the retrieval of call records, programming, and diagnosis of the digital VOIP gateway/signaling converter. It has an intuitive operational logic and an extensive HELP documentation which comes with the supplied software CD. The minimum system requirements for XMan™ are: Figure 5. The XMan™ maintenance software
Figure 6. “User login” dialog box
• • • • • • • • •
A PC with Pentium™ 300 Mhz or better processor Minimum 32MB RAM Minimum 40MB free hard disk space One free serial COM port (RS-232) Internal or external modem for remote maintenance 10/100 Mbit Ethernet port for remote maintenance VGA screen with minimum 800x600 resolution Microsoft Windows™ 95/98/Me/NT/2000 or XP DAO (Data Access Objects) must be installed
Before installing XMan™, install the DAO (Data Access Objects) from the supplied software CD. Install the XMan™ software on the maintenance PC and run the program. In order to use the software, the user is required to enter a username and password. Go under the “Users” menu and click on “Login”. The default username and password are: Username: SYSTEM Password: SYSTEM
The maintenance PC and STILLINK 200 can be connected via the supplied RS-232 cable. This is a proprietary cable specific to XMan™ with special connections and is not substitutable.
Figure 7. “Connect To” dialog box. Connection with the COM port.
Once you login to the system, go under the “Remote” menu and click on “Connect...” to connect to STILLINK 200. You will need to specify the serial port used for the connection. Set the baud rate to 38400 or lower then click on the “Connect” button to get connected to your STILLINK 200.
9
INSTALLATION MANUAL SOFTWARE Once you get connected to your STILLINK 200 the connection window will be opened with the connection configuration as shown in Figure 8. To establish your next connection via ethernet follow the steps below: Figure 8. Successful connection.
• • • • • • •
Go into the “Ethernet properties” page by Remote->Ethernet in the menu. Figure 9. Enter your IP address and subnet mask Press on the “Send” button. In the menu goto Remote->Stored parameters and click on the “from operational data” to save the parameters to the non-volatile memory. Restart the system Now, under the “Remote” menu, click on the “Connect...” again. Select “IP Internet protocol” as the Line device and enter the IP address you had assigned for your system, and click on the “Connect” button. Figure 10.
Now that you have established your connection with your STILLINK 200 via the ethernet port. For the rest of your configuration settings please refer to the XMan™ Help file.
Figure 9. “Ethernet properties” dialog box.
Figure 10. “Connect To” dialog box. Connection with the ethernet port.
10
