Instruction Manual

Transcript

GRANDVIEW REPRODUCING GENUINE COLORS Instruction Manual Recessed-Ceiling Motorized Projector Lift Applicable Model GPCK-MB Please read being installation: Thank you for purchasing this product. Please read the instruction manual carefully to ensure this projector lift is suitable for your installation environment. Notice Warnings This product should only be installed by a qualified technician. Please review the manual carefully to ensure it is properly installation and to avoid injury. The ceiling used must have a minimum load bearing of 20KG. Grandview Crystal Screen Canada Ltd. Guangzhou Grandview Crystal Screen Co., Ltd. #11- 3751 North Fraser Way, Marine Way Business Centre, Burnaby, BC, Canada V5J 5G4 Tel: 1-604-412-9777 Fax: 1-604-412-9796 Website: www.grandviewscreen.ca P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road, Shiqiao, Panyu District, Guangzhou, Guangdong, China Tel: +8620-8489-9499 Fax: +8620-8480-3343 Website: www.grandviewscreen.com Caution For projector lift assembly only Do not take apart Please do not take apart the accessories of mounting bracket Cautions for Location Please keep away from hot objects, dirty environments, high temperatures and high humidity. Do not use in environments with heavy wind. Warning: Avoid wet areas to avoid electric or fire hazards. 1. Please read carefully with this instructions before installation to avoid damage to product causing by inappropriate installation or operation. 2. Please keep the projector lift away from hot sources, such as radiator, heating machine, fireplace, loudspeaker or other relative device. 3. Only connect with ground wire. 4. Only authorized accessories can be used. 5. Unplug the power wire in adverse conditions or if it will not be used for long periods of time. 6. Repairs should only be done by authorized technicians. 7. The lift should not come in contact with water. 8. As soon as the plug of the screen is connected to the power source, the screen is connecting with electricity. 9. Please use the approved power line (three-core power line)/ device interface/power plug. 10. Please use the rating (voltage, amps) power line (three-core power line) / device interface/power plug. If have any questions about power line/ device interface/power plug, please contact the professional people. 11. After installation, please locate a power device in order to disconnect power or connect the power plug to electrical socket. This electrical socket should be installed to a convenient position. If the accident occurs during operation, please disconnect power or take out the power plug. 12. The ceiling or wall used for fixture installation must be secure enough; load-bearing requirement must be 4 times of the projector lift to prevent the projector lift from falling. 13. Do not put any other objects on the lift. Tips Cautions for Repairing Do not take apart or remove the screws. If this products needs maintenance or repairs please contact a qualified technician or dealer. Do not take apart Questions & Answers Grandview products are designed to last and most problems are commonly easy to fix. If a problem occurs, please refer to thelist below for some common solutions. If problems persist,please contact an authorized Grandview dealer or call the service number: (8620) 84899499 Reason Pr oj ec tor Li ft res po nd s no thi ng to an y op er at ion Solution Battery mis-installed or powerless Please check the batteries Power line disconnection Please connect the power line with refering instruction manual. Three Years Warranty Grandview provides a three years warranty. Covered under warranty is thereplacement of spare parts if problems occur To prevent injuries caused by electric shock, do not remove any parts. Users should not checkany internal parts. Please contact an authorized technician for any problems. during proper operation of the unit. Not included is damage incurred due to improper operation of the unit or improper installation. Contact Grandview or your local authorized dealer for more information. instruction Cleaning Please clean the projector and projector lift at the same time. 1 18 Accessories Caution Please comply the following contents for installation and use M4 Hexagonal Adjuster (1pc) Hanging Piece (4pcs) Fixed Piece (2pcs) Cautions Please do not shake the projector lift Please do not lift up the projector lift M10X100 Screw (4pcs) NO M6X16 Screw and Nut (12pcs) Fixed-Frame (1pc) NO Controller (1pc) Battery (1set) Warranty Card Instruction Manual Maintenence The lift can be cleaned using light neutral detergents only Optional Accessories Wall-Switch(1pc) Ornaments Board (1pc) Multi-Media Box(1pc) Side-Frame Fixed Piece(4pcs) Use lubricant to keep the turning screw clean M10 Threaded Rod (4pcs) M10 Nut、Washer (16pcs/each) Driving Screw M3X5 Screw (8pcs) 17 Ornament Side-Frame (4pcs) 2 Hanger(4pcs) Construction for Projector Lift Kindly Reminder: Do not change the factory pre-settings for any urgency,pls operate according to the following instructions if necessary 2) Remote Setting Fixed-Frame Motor a. When the projector lift is at the loading position, you can adjust the lower and upper limitation via the remote control. b. Press the reset hole with a pin or equivalent at the back of the remote control for 3 seconds and release. Then press the UP button and stop at the desired position. The projector lift is now set at its retract limit. Frame UP Linkage Red LED DOWN Sling wires localizer Figure 23 Projector Lift Figure 24 c.To press the localier hole at the back of the remote controller with one small pin or equivalence for about 3 seconds and release, then press DOWN button for strap to the desired position and stop, the projector lift is already reset for its retract limit. Projector Fixer Front View Side View Figure 25 Hanger M10 Nut M10 Threaded Rod Figure 26 Kindly tip: For ensuring the security of positioning function, the effective setting period of electric positioning should be 60 seconds, after 60 seconds will return to normal situation. If the setting fails within 60 seconds, please repeat as following step; to press the setting button; then LED light will turn off; press the setting button again, then LED light will turn on. In this movement, the resetting function will begin. Motor Positioning Figure for Installation Bracket Top View Do not operate continuously for over 4 minutes at a given time to avoid overheating. If the motor overheats, do not use for at least 30 minutes. No lubrication is used on the motor and the drop and retract limit of the screen has already been propositioned at an optimal Upper Limitation setting before delivery. Inorder to avoid motor damage, please contact a qualified technician for consultation if a new position setting is needed. Use the M4 allen-key for adjusting the upper and lower limitation of projector lift, but the distance can not be over than the value D in specification table. Lower Limitation 3 16 Projector Lift Positioning Function Specifications There are 2 methods to position the projector lift - set by the upper and lower limitations on the remote. 1) Upper/Lower Limitation Adjustment for Sling Wires The upper and lower limitations are preset at the factory. The upper limitation is slightly higher than the ceiling and the lower limitation is shown in value D on the specifications table. Please note the upper and lower limitations for the sling wire installation must be done by an qualified technicianto prevent any injury or damage. Figure 20 Product Specifications Size (unit:mm) Model GPCK-MB1800 510 510 110 360~1800 520 520 225 Larger than 470mm GPCK-MB1000 510 510 110 360~1000 520 520 225 Larger than 470mm Figure 21 The following steps must be done by an qualified technician. a) For upper limitation adjustment, take off the knob and use the provided allen key to adjust. A clockwise adjustment will retract the projector lift (the distance of the installation position of the casing will decrease) and a counterclockwise adjustment will extend the projector lift position (the distance of the installation position of the casing will increase). b) For lower limitation adjustment, take off the knob and use the provided allen key to adjust. A clockwise adjustment will retract the projector lift (the distance of the installation position of the casing will increase) and a counterclockwise adjustment will retract the projector lift position (the distance of the installation position of the casing will decrease). Upper Limitation Lower Limitation Figure 22 15 Limitation of Ceiling Height 4 Connect the power for projector lift A, and send out directive oxFF ox10 ox11 ox12 oxAA. At the same time, the address of projector lift A is ox10 ox11 ox12. Entering the operating address of projector lift A can control this projector lift. Installation This lift needs to be installed recessed into the ceiling. The instruction below shows us the grille-ceiling as an example so please install the screen based on your installation requirements. The lift needs to recessed at the proper level to ensure correction operation. Take out all parts and accessories and follow the guideline to ensure you have all the needed parts. Directive for retracting: OxC9 Directive for stopping: Directive for extending: * For your safety and to ensure proper installation, please read this manual carefully and choose a installation needed for your environment. Figure A shows an extended installation with screws while figure B is a direct installation. OxE9 Completed the studying in projector lift A, and then disconnect the power for projector lift A. Please operate the projector lift B in the same way and change the address to oxAA oxAA oxAA. Entering the operating address of projector B can control this projector lift. Concrete Concrete Directive for retracting: OxC9 Directive for stopping: Directive for extending: Screw H-400 Hanger OxE9 This studying is one address bit for a long time untril next address bit change to update. H After studying address bit, the common directive is still effectivr, so the address bit can not be oxEE oxEE oxEE. H Attachment 1 Grille-Ceiling Compare 16 hexadecimal system and 10 hexadecimal system Grille-Ceiling Projector Lift Projector Lift 16 hexadecimal system 10 hexadecimal system Screw Screw 4. Remote Control Instructions In order for the control to work with the projector lift, it first needs to be programmed before it can be used. Figure A Figure B Grille-Ceiling Mount 1. Choose a position according to the required space, and then take apart the ceiling (figure 1). Please measure the distance H between roof and ceiling surface correctly (figure 2) 1) The projector lift needs to be set on load. 5 seconds after connecting the power, press the UP button and STOP button simultaneously for 5 seconds before releasing. 2) Press the DOWN button to ensure the programming works. 3) If it did not program, please repeats steps 2 and 3. Concreted-Ceiling Roof Surface H Take apart the ceiling Grille-Ceiling Ceiling Surface Figure 18 Figure 1 Figure 19 Figure 2 5 14 Grandview Projector Lift RS485 Setting Address 1、RS-485, RS-232 input A continuous data sends two times，each time interval of 200ms 3 bytes of studying address directive are custom setting address directive 2. The bracket is a part of the projector lift combined with the hanger, screw (M10), and nut (M10) to be following mechanism. Cut the length of the screw (M10) for H-C+60mm, where H is the distance of the concrete ceiling and the ceiling surface (measured in the last step). C is the height of the frame as shown in the specifications table. Central Control Format Agreement Cotter Pin Hanger 1)Communication Agreement Setting Data Bits: 8 bits Start Bits: 1 bit M10 Nut Baud Ratio: 2400 Common directives are in chip of projector lift and can not be changed 2) Directive for retracting： OxC9 3) Directive for stopping： 4) Directive for extending： probably 60mm H-400mm Stop Bits: 1 bit 114m m M10 Threaded Rod M10 Locknut OxE9 5) Studying address directive: Figure 3 2. Directive Composing Instruction: oxFF is only bit; ox stands for hexadecimal system; FF is effective bit; a directive is composed by 5 bits. Studying directive oxFF oxXX oxXX oxXX oxAA oxFF and oxAA can not be changed, but oxXX oxXX oxXX can be changed to any 16 hex data, which stand for address bit 3. Ensure the distance M and N is according to figure 4 and the model of the table below. Install the brackets to the ceiling via screws as shown in figure 5. (Note: due to product updates, sizes and specifications are subject to change at any time) The changed working directive 1) Directive for retracting: M OxC9 2) Directive for stopping: 3) Directive for extending: 4) Studying address directive: N Example: The studying directive is oxFF ox10 ox11 ox12 oxAA which can be changed to: 5) Directive for retracting: Size(unit:mm) Model M N GPCK-MB1800 560 440 GPCK-MB1000 560 440 OxE9 OxC9 6) Directive for stopping: 7) Directive for extending: OxE9 H-C+ 60 8) Studying address directive: H 3. Learning Directives and Operation After the power is connected, the learning status will stay for the first 10 seconds. The learning directive is oxFF oxXX oxXX oxAA. The lift can be used after the learning process is completed, but it cannot be used properly N M Figure 4 after the address bit is changed. Tis is because one port can used to control many projector lifts. Example: If there is a projector lift A and B with RS-485 ports, in order to control these two lifts simultaneously the directive oxFF oxEE oxEE oxEE oxDD will be sent out from the port. In order to control these two lifts in different movements, for example lift A goes down while left B goes up, a common directive cannot be used and must be separated by an address bit at this time Figure 5 12 6 4. Figure 6 - Install the projector lift and fasten/secure. The low frame of the projector must align to the ceiling. Central Control Instruction Emitter Function Common Line Switch for Retracting Stop RS232 Input B Switch for Extending RS232 Input A Central Control Format Agreement 1) Communications Agreement Setting： data bits: 8 bits、start bits：1 bit、stop bit: 1bit、baud ratio: 2400 2) Directive for retracting： Crystal Socket OxC9 3) Directive for stopping： Figure 6 4) Directive for extending： OxE9 232 setting: 2400, n, 8, 1 a continuous data sends two times，each time interval of 200ms. Stop Down Up 5. Figure 7 - Check the balance of the projector lift. Install the two fixed pieces as shown in the figure below. Multi-Function Control Diagram Nut Projector Lift Stop Projector Lift Down Projector Lift Up Fixed Piece Figure 7 7 10 Common 6. To install the lift, please follow the directions as shown in figure 8 and 9 in reference to button A and B. Follow the sequence of figures 10-13 and push button B into button A, then fasten the screws as shown in figure 14. Instruction 1.Remote controller instruction Button A UP STO P DOWN Button instruction for controller 1. Press "UP" ,projector goes up 2. Press "STOP" ,projector stops 3. Press "DOWN" ,projector goes down Button B Front view Button B Remote controller guideline: 1. Work temperature: -20°to 70° 2. Batteries: 1.5V x 2pcs, model: AAA. 3. Take out the batteries if the controller will not be used for a extended period of time. 4. Please change the batteries when signal is weak. Red LED Sling wires localizer Button A Figure 8 Figure 9 Installation for controller batteries Please replace the batteries when the signal of controller is weak 1. Push out the battery cover on the back of controller 2. Install the batteries as guide arrow 3. Reinstall the battery cover Caution Install the batteries correctly Figure 10 Back view Figure 11 Figure 12 Wall-Switch Function Please follow the signs and symbols on the wall-switch Wall-Switch (6p6c) CENTRAL CONTROL Cable(8PIN) POWER HDMI Screw UP STO P DOWN Screw VIDEO VGA Figure 13 11 Figure 14 8 7. Cut the ceiling board (Step 1) to a suitable size which can accommodate the gap after the projector lift is retracted. 7. Figure 15，connect the power cord and signal cord（Circuit wiring diagram 16） Figure 15 Figure 17 Brown line Circuit Board Brown line Black Line Black Line Yellow and Green Line 8. Please read the "Remote Electric Positioning" section for controlling the projector lift. After the adjustment, ensure the height of the projector lift is set to your needed specifications. Ensure the bottom of the projector lift is aligned with the ceiling after it's retracted. Note: the operation of this lift must be operated by a qualified professional. Blue line Brown line Yellow and Green Line Blue Line Socket Figure 16 9 10