Transcript
Instruction manual Babyfix base
Base For babies weighing up to 13kg
Tested and approved according to
ECE R44 / 04
Introduction Thank you for choosing a child seat base from Axon Kids. The team developing Babyfix have more than 30 years of experience in child safety products between us, and we have done our outmost to make this product as safe as possible. This base has been developed to be used both with ISOFIX-system and with fastening manually by the belts. Babyfix base has a ”semi-universal group 0+” approval for a child who weighs up to 13 kg and approved ISO/R1 holders.
Babysfix base has an ISOFIX holding device and is approved according to ECE R44/04 regulations. Babyfix base could be used in all positions of the car that is approved for ISOFIX holding device. When the base is used together with the car belt make sure that the car is approved according to ECE 16 regulations. Do not attempt to dismantle, modify or add to any part of the child seat or change the way its harness or your car seat belts are made or used. The official approval is no longer valid if modifications are made. Keep these assembly instructions thru out the lifetime of the base. Do not attempt to assembly the base with the ISOFIX holding system without using the leading covers.
Read the instruction manual carefully before you assembly the base. Otherwise you risk to seriously harm your child.
The parts of the base
1. 2. 3. 4. 5. 6. 7. 8.
Backrest ISOFIX guiding arms Fixationhooks for the car belt Leading covers for ISOFIX Releasebutton for childseat Adjustment button for the supportleg Supportleg Belt lock-off
4
Assemble the base
1. Attach the belt lock-off to the backsupport. Insert the two legs of the back support and fixate to the base with the screws included in the box.
2. If ISOFIX holding system should be used you need to fold them out according to picture above.
Warning! Dont unfold the ISOFIX holders if you are not going to use them. This could create damages to your car interior, if they are not used fold them back according to pic 3.
5
Attaching base to the car seat You could use either the belts of the car or the ISOFIX holding system to fixate the base to the car seat, dependent of your car specifications. If you are uncertain of which system to use check your car manual for information.
1. Pull the car seatbelt under the hooks as shown in picture 1. Lock the belt, picture 2. Then press the base unit into the seat and pull the car seatbelt as far as it will go then attach the belt lock-off. The belt lock shall always be on the same side as the car buckle. 2. Extend the leg by pushing the release button and adjust the length so that it is fully supported by the car floor, pic 3. Ensure that the leg is standing firmly against the floor and that the base is not able to slip.
3. The base should look like in picture 4 when it is assembled correct.
6
Using the base with ISOFIX 1. Assemble the leading covers for the ISOFIX holding system to the car, pic 1. 2. Extent the two ISOFIX holders legs and assemble them into the leading covers which you assembled in first step, picture 2 and 3. You will know that they are assembled when you here a click sound. Check that the color marking on the restraint mechanism has changed to green, picture4, and that the base is firmly positioned. 3. Extend the leg by pushing the release button and adjust the length so that it is fully supported by the car floor (picture 5). 3. Ensure that the leg is standing firmly against the floor and that the base is not able to slip.
7
Attaching and removing baby seat
1. Press down the baby seat until you hear a click sound. Check if the baby seat has locked correctly by pulling the handle upwards, the seat should not detach from the base. 2. Then push down the handle to position B like in the picture to the right. 3. To detach the baby seat from the base push the release button and then lift the seat upwards. Warning! Always make sure that your child is seated firmly when you lift and carry your child and seat to avoid injuries.
8
Detach the base from the car seat
1 A. If the base is assembled with ISOFIX holders then release this by pressing down the red ISOFIX restraints mechanism button, picture 1, on both sides. 1 B. If the base is assembled with the car seatbelt, simply press the latch on the car belt to release the belt. 2. Fold the ISOFIX holders together into the base according to picture 3. 3. Press the release button in the leg and push the leg upwards to bundle it up together, picture 2. 4. Fold the leg together underneath the base and secure it according to picture 4.
Producer: Axonkids AB Box 188 53322 Götene www.axonkids.com
