Transcript
Aventura Technologies 180 Adams Avenue Hauppauge, NY 11788 (877) 707‐9600 www.aventuratechnologies.com
Instruction Manual SFP Based, 10/100 Ethernet Media Converter / Transceiver
Model Numbers: FBR-1FE1FX-SFP – SFP Based, 10/100 Mbps Ethernet Transceiver
© Copyright 2008, Aventura Technologies, Inc.
INSTALLATION AND OPERATION INSTRUCTIONS FUNCTIONAL DESCRIPTION The FBR-1FE1FX-SFP operates as one half of a transceiver pair for the transmission of bi-directional Ethernet data, over one or two multimode or single-mode fiber/s. The unit uses industry standard Small Form-Factor, Pluggable (SFP) modules for connecting to the fiber media. A proper Aventura Technologies approved SFP module is selected by the customer to accommodate the type and number of fibers, as well as the transmission distance. The FBR-1FE1FX-SFP converts a single 10/100base-T/TX Ethernet input to an optical fiber output. The FBR-1FE1FX-SFP also converts an optical fiber input, returning over the same or different fiber, depending on SFP module selection, into a single 10/100base-T/TX Ethernet output. The FBR-1FE1FX-SFP is configured to auto-negotiate the data rate on the UTP Ethernet port to either 10 or 100 Mbps and operating mode to either full or half-duplex. Additionally, the unit is configured to perform the MDI/MDIX sensing and switching automatically. This feature allows for the use of standard, straight through patch cords, without regard to the configuration (MDI or MDIX) of the device the FBR-1FE1FX-SFP unit is connected to. The data rate on the optical port of the FBR-1FE1FX-SFP is always 100Mbps, full-duplex. This unit is contained in a compact and rugged steel housing with internal dc voltage regulation. The detachable terminal block and LED indicators provide for easy installation and monitoring of Ethernet, optical link, and dc power status. The unit operates as either a surface mounted, modular, stand-alone device, or within a rack mounted card cage. INSTALLATION THE INSTALLATION OF THIS UNIT SHOULD BE MADE BY A QUALIFIED SERVICE PERSON(S) AND MUST CONFORM TO ALL LOCAL CODES. The physical outline and front/rear panel configuration of the unit is detailed in Figure 2. Mount the unit to a secure surface using #8 (3mm) hardware in two places. See Figure 3 for a full size mounting template. Be sure to allow sufficient room for the required minimum bend radius of the fiber cable used. POWER SOURCE The unit requires a +12VDC power source for proper operation. The DC input is diode protected against reverse polarity connection. In the USA and in Canada, for standalone surface mounted installation, an Aventura Technologies FBRPSUS12DC1A is supplied with this unit. Contact Aventura Technologies for ordering power supply units for use in countries other than the USA and Canada. When installed in a rack mounted card cage, the power for the unit is supplied from the card cage’s power supply.
© Copyright 2008, Aventura Technologies, Inc.
2
POWER CONNECTION Power is supplied to the unit via a two-pin terminal block connector. Follow the labeling on the unit for proper connections of the +12 volt dc and ground leads. ETHERNET CONNECTION The UTP Ethernet connection is made via an RJ-45 connector on the front of the unit. For proper operation, the use of a patch cord and/or cable rated Category-5 or better is required. FIBER CONNECTION The fiber optic connections vary, depending on the selection of SFP module. Refer to the instructions supplied with the SFP module for the proper procedure of installing the SFP module in the FBR1FE1FX-SFP unit, as well as for the proper procedure for connecting the fiber to the SFP module. STATUS INDICATORS Each unit provides the following LED status indicators to aid in installation and troubleshooting: POWER INDICATOR A bi-color LED indicator monitors the voltage at the unit’s input connector and the operating internal voltage of the module. The power status associated with this indicator is summarized below. Power Indicator Green Red Off
Power Status Proper Input Voltage Present – Proper Internal Operating Voltage Present Proper Input Voltage Present – Internal Operating Voltage Faulty No Input Voltage Detected
OPTICAL LINK INDICATOR A bi-color LED indicator monitors the power of, and proper synchronization with the optical input signal that is being received at the FBR-1FE1FX-SFP. The optical link status associated with this indicator is summarized below. Optical Link Indicator Green Red Off
Optical Status Proper Optical Input Present Optical Input Not Detected Check Power Supply
ETHERNET INDICATORS Two LED indicators on the RJ-45 connector of the FBR-1FE1FX-SFP unit monitor the status and operating mode of the UTP Ethernet link. The Ethernet status associated with these indicators is summarized below. Ethernet Indicators Speed (GREEN) Link/Activity (GREEN)
Ethernet Status Lit: Link operating at 100Mbps Unlit: link operating at 10Mbps or no link Lit: Good link on the port Blinking: The port is receiving/transmitting data Unlit: No link
© Copyright 2008, Aventura Technologies, Inc.
3
Device FBR-1FE1FX-SFP
Compatible With FBR-1FE1FX-SFP-MINI FBR-1FE1FX-SFP FBR-2X1FE1FX-SFP FBR-1FE2FX-SFP
Figure 1 – List of Compatible Devices
Figure 2 – Physical Outline And Front/Rear Panel Configuration Of Units
© Copyright 2008, Aventura Technologies, Inc.
4
Figure 3 – Surface Mounting Template (1:1)
© Copyright 2008, Aventura Technologies, Inc.
5
LIMITED LIFETIME WARRANTY INFORMATION This limited lifetime warranty applies only to the original end user customer of the product for so long as the original end user customer owns the product. This limited warranty is non-transferable. Damage due to shipping the products to you is covered under this limited warranty. Otherwise, this limited warranty does not cover damage due to external causes, including accident, abuse, misuse, problems with electrical power, servicing not authorized by Aventura Technologies, Inc., usage not in accordance with product instructions, failure to perform required preventive maintenance, and problems caused by use of parts and components not supplied by Aventura Technologies, Inc. During the warranty period beginning on the invoice date, Aventura Technologies, Inc. will repair or replace products covered under this limited warranty that are returned to Aventura Technologies, Inc.'s facility. To request limited warranty service, you must contact Aventura Technologies, Inc.'s Customer Technical Support within the limited warranty period. Refer below to find the appropriate contact information for obtaining customer assistance. If limited warranty service is required, Aventura Technologies, Inc. will issue a Return Material Authorization Number. You must ship the products back to Aventura Technologies, Inc. in their original or equivalent packaging, prepay shipping charges, and insure the shipment or accept the risk of loss or damage during shipment. Aventura Technologies, Inc. will ship the repaired or replacement products to you freight prepaid if you use an address in the continental United States, where applicable. Shipments to other locations will be made freight collect.
To view the full terms of the warranty, please go to: www.ati247.com SERVICE INFORMATION There are no user serviceable parts inside the unit. In the event that service is required to this unit, please direct all inquiries to: Aventura Technologies, Inc. 180 Adams Avenue Hauppauge, NY 11788
Phone: (631) 300-4000 FAX (631) 434-7000 E-mail:
[email protected]
© Copyright 2008, Aventura Technologies, Inc.
6
