Transcript
SPECIFICATION Model: Voltage: Current: Paper entry width: Shred size: Shred paper capacity: Shred speed: Waste bin Volume: Noise level: Duty cycle:
CC1610 220-240VAC,50Hz 1.5A 220mm 5mm x 32mm 10 A4 Sheets 70gsm/1 Credit Card 2.5 Mtrs/Min 16L 70.9db 2 Mins On/30 Mins Off
Net weight: Dimension:
3.6Kgs 355 x 170 x 395mm
Type designation:
Instruction manual CROSS CUT SHREDDER CC1610
BS60950-1:2006 EMC Directive 2004/108/EC Test Standards:EN55014-1:2006 EN55014-2:1997+A1:2001 EN61000-3-2:2006
EN61000-3-3:2008
Visit www.texet.com for details on other Texet products. UK: Waste Electrical products/batteries should not be disposed of with household waste. Separate disposal facilities exist, for your nearest facilities, see www.recycle-more.co.uk or in store for details.
Made in China Please Read the Following Instructions Carefully before Use, and Keep them for Future Use.
http://www.texet.com
GENERAL SAFETY Thank you for purchasing the TEXET Cross Cut Shredder, CC1610, with normal use and maintenance, your shredder will provide years of satisfactory performance. Please read the instruction manual carefully and retain for future reference.
When using electrical appliance, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons including the following; The Shredder is only intended for private/domestic and small office use. Any other uses not recommended by the manufacture, may result in the warranty being void. Do not use the shredder to shred film, OHP Pouches, adhesive stickers, cloths or any plastics, other that credit cards, as these may cause damage.
Power On Light
Remove the Shredder from its packaging and check to make sure it is in good condition before using. Keep the packaging for storage and transportation.
Overheat Light
Paper Feed Slot
Controls – REV
OFF AUTO
To protect this Shredder correctly and avoid any damage, please ensure you understand the following Icons:Please do not spray any flammable gas, water or oil onto this Shredder. Please keep children away from the Shredder, the sharp blades may harm them. Please keep cloths, ties and the like away from the paper entry slot. To prevent damage to the cutters remove paper clips, staples and other fasteners before shredding.
This Shredder is not intended for use by persons, including children, with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the Shredder by a person responsible for their safety. Extreme caution is necessary where children or persons with reduced physical, sensory or mental capabilities may come into contact with the Shredder when in use. Do not let children play with parts of the packaging, such as plastic bags. Ensure the power supply to the socket into which the Shredder is plugged, is in accordance with the rating label on the shredder and that the socket is earthed. Do not use the Shredder if the Power Cord is damaged. If the Power Cord is damaged it must be replaced by a recognized service agency or other qualified person. Always turn the Power off before unplugging the Shredder and make sure your hands are dry to prevent electric shock. Do not use outdoors.
Please keep your hands out of the paper entry slot and the sharp blades may cause injury. Please keep your hair away from the shredder/paper entry slot. The incorrect operation of this appliance may cause personal injury or damage the shredder. The Plug Socket outlet should be easily accessible. BS Plug Fuse – 3A Fitted
Always unplug the Shredder when not in use. Setup: 1. Remove the shredder from the outer carton. 2. Place the shredder head onto the bin. The shredder head is fitted with as a safety switch and this switch needs to sit on top of the Rib that is located on the inside of the Waste Bin, (left hand side at the back), as indicated by the Safety Interlock labels on the Shredder Head and Waste Bin. 3. The shredder needs to be placed on a flat stable surface.
Shredder Capacity: The CC1610 will shred 10 sheets of A4 70g paper at once or 1 Credit Card, and will accept paper width up to 220mm.When shredding smaller items like envelopes or credit card receipts/Credit Cards, insert them through the middle of the feed slot. The paper sensor is located in the centre of the main feed slot. When paper is inserted, the sensor starts the cutters. When the paper has gone through the shredder, the sensor will switch the cutters off.
If not move the switch alternately between REV and Auto 2-3 times, this should clear the paper jam. Put the switch back to Auto and carry on shredding. ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE AN ITEM FROM THE PAPER ENTRY. DO NOT, UNDER ANY CIRCUMSTANCES, INSERT METAL OBJECTS INTO THE ENTRY FEED SLOT OR THE BLADES, TO REMOVE THE JAMMED PAPER.
Maintenance Operating the Shredder: 1. Prepare the paper to be shredded by removing paper clips and any other objects that may jam in the feed slot. 2. Only feed 10 sheets of 70g A4 paper at any one time or 1 Credit Card. 3. Set the select switch on top of the shredder to AUTO, OFF or REV position for the desired operation
REV: Reverses the shredding direction and backs items out of the shredder in the event of a paper jam. OFF: This position is recommended when emptying the shredder bin or when the shredder is not in use for a prolonged period of time. AUTO: Activates the auto shred function, the shredder will start automatically when an item is inserted into the paper feed slot and will stop once the paper has been shredded. Paper Jams: The CC1610 is equipped with a motor overload protection device, the normal duty cycle for continuous shredding at maximum capacity, is 2 minutes on & 30 minutes off. The power may terminate automatically in case of the following situations: 1. Operating the shredder at maximum capacity continuously for a prolonged period of time, e.g. more than 2 minutes without stopping. 2. Exceeding the shredding capacity e.g. inserting more than 10 sheets at one time, or if the paper is not fed squarely into the feed slot. Both of these operations may result in the activation of the automatic motor overload protection, which terminates the power to the unit. If this occurs, you should: 1. Unplug the power cord from the AC outlet and wait at least 30 minutes for the overload protection to reset. 2. Plug the power cord back into the AC outlet and place the switch in REV. Pull the remaining paper out of the cutters. Place the switch back to the AUTO position if necessary. 3. With the switch in the AUTO position and the feed slot clear, you are now ready to resume normal shredding. If the shredder overheats, the red overheat light will come on and it will automatically shut down, it will restart again after 30 minutes, once the shredder has cooled down Clearing the Blades of Paper Jams If paper becomes jammed during shredding, move the switch to reverse and remove any excess paper from the feed slot. Move the switch back to auto and see if this clears the jam,
Warning: When you want to maintain the shredder, please make sure you have switched off the shredder and removed the plug from its socket. Use a dry soft cloth when you want to clean the shredder. The shredder cover and waste bin are made of plastic; therefore please do not use gasoline, benzene impregnate thinners to avoid fading or scratches. Do not allow water to enter the shredder head when cleaning. To maintain the quality of your shredder blades please use Texet LB12 lubricating sheets once a month. Waste Emptying: 1. When you empty the waste bin, please make sure the shredder is switched off and unplugged. 2. Place the shredder head back onto the bin correctly. Paper is easily wrapped around the shredder head if the waste bin is allowed to get too full, therefore please empty the waste bin after shredding 90 A4 Sheets. Disposal: Please dispose of this product responsibly at an approved disposal site or recycling facility. Do not dispose of this product in household waste.
TROUBLE SHOOTING Troubles Shredder does not work after paper is inserted.
Shredder does not stop after shredding has finished
Reason 1. The power cord may not be properly connected. 2. The motor has been over heated. 3. The paper feed may be jammed. 4. Shredder head is not placed properly on basket.
1. The mechanical sensor may be jammed by paper
Solution 1. Check the power cord is correctly plugged in both the plug socket and the shredder. 2. Wait for about 30 minutes and try the shredder again. 3. Reverse the paper feed and remove any jammed paper, then try again. 4. Place shredder head securely on basket, correctly front facing, ensuring contact with the basket is made. 1. Clean the paper entry and try again, ensuring you remove the plug from the socket first.
Shredder makes a high noise
1. The shredder may not be placed on a flat/stable surface.
1. Replace the shredder onto a flat/stable surface.
Shredder does not shred paper
1. Too much paper is inserted. 2. The paper size inserted may be larger than the paper entry. 3. The paper may be inclined when placed into the paper entry.
1. Check to see if you have exceeded the rated capacity of paper (10 sheets of 70 g). 2. Reverse the shredder and take out the paper, fold in half and try again. 3. Re-insert the paper vertically.
