Transcript
L1760 05 12_Layout 1 08/05/2012 13:45 Page 1
INSTRUCTION MANUAL True MistTM
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep for your reference. True Mist Instruction Manual
Congratulations on purchasing the True MistTM. This product has been specially designed to provide an efficient application of tanning solution products.
Take a minute to read and understand how to operate your new True MistTM and you will be able to provide the perfect flawless tan with every application. Your True MistTM is packaged with the following:
1. True MistTM turbo powered spray unit 2. True MistTM air hose 3. Helia Spray gun 4. Instruction manual 5. Three spare containers plus one on the gun
L1760 05 12_Layout 1 08/05/2012 13:45 Page 2
The True MistTM exploded diagram and parts list
1
2
3
4
5
6
7
8
9 13 A
B
10 11
No. 1. 2. 3. 4. 5. 6.
Description Air cap ring Air cap Air direction plate Fluid tip Fluid tip o-ring Fluid needle
Part No. V0270 V0273 V0269 V0244 V0005 V0245
No. 7. 8. 9. 10. 11. 12.
12
Description Flow adjuster Pot lid seal Flexible pick up tube 250ml container Hose Assembly Filter
Position the pick-up tube on the pick up port as shown
2
Part No. V0254 L1309 L0947 L0909 V0337 L0290
L1760 05 12_Layout 1 08/05/2012 13:45 Page 3
Safety Instructions
• Only use the tanning equipment as detailed in these instructions. • The tanning solution must not be inhaled. We recommend that your clients use nose plugs. • Advise your clients not to wear deodorant, perfume or make-up for the spray tanning session as these products could affect the performance and colour of the tan. • Advise your clients to remove any jewellery before the spray tanning session starts as this may become discoloured. • Advise your clients to shave or wax 24 to 48 hours before their spray tanning session is due. • Advise your clients to always cover their hair while their face is being spray tanned, especially if their hair is bleached as this can be stained by the tanning solution. • Make sure the area where you spray tan is adequately ventilated. • Do not apply tanning solution to open cuts, broken or damaged skin. Cosmetics may cause a mild reaction if your client has sensitive skin. • Advise your clients to avoid wearing light coloured clothing after spray tanning. • If tanning solution is sprayed into the eyes, flush them out with water and seek medical advice immediately. • Never immerse the motor unit in water. • Warning. Do not use your spray tan equipment near bathtubs, showers, basins, or other vessels containing water. • Always disconnect the motor unit from the mains supply when re-filling the spray gun container or when cleaning the tanning equipment. • If you use your spray tan system close to a hand basin, shower or a similar source of water, unplug it after use because the proximity of water presents a hazard even when the equipment is switched off.
3
L1760 05 12_Layout 1 08/05/2012 13:45 Page 4
Safety Instructions
• Do not spray into light switches or power sockets. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Never allow children to operate the tanning system. • Never spray or aim the spray gun at animals or livestock. • We recommend that you clean your spray equipment after every use. • Use only genuine manufacturer replacement parts. • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels containing water. IMPORTANT: Patch Test We recommend testing tanning solution and other cosmetics on a small area of your clients’ skin 24 hours before spraying a large area. If irritation occurs discontinue use.
4
L1760 05 12_Layout 1 08/05/2012 13:45 Page 5
Preparing your equipment for use
Your tanning equipment is supplied as 2 main components, the motor unit, which includes the hose, and the spray gun. Please refer to the exploded drawing on page 2 and follow the simple instructions below.
• • •
•
Unscrew the Container (10) from the spray gun and fill it with tanning solution. Do not overfill the Container. Normally 50ml of solution is enough for one application.
Make sure the Pick-up Tube (9) is pushed firmly into the lid of the spray gun. Carefully screw the Container back into the lid of the spray gun, ensuring there is an airtight seal. Connect the hose to the spray gun by pushing it firmly into the hose inlet at the back.
Uncoil the mains cable from the base of the motor unit and connect the mains plug to a suitable 230V supply socket. Switch on the motor unit. No tanning solution will be sprayed until you pull the spray gun trigger.
Setting up the Spray Gun
Before beginning a spray tan session, we recommend that you set the spray pattern and the amount of solution to be sprayed to your own preferred requirements. • Adjust the spray pattern by rotating the `Spray `Direction Plate as shown in Fig.1. We recommend that you use a horizontal spray pattern. • Adjust the volume of solution applied by adjusting the Flow Adjuster dial at the back of the spray gun (Fig.2). Scroll it down to reduce the amount of solution and up to increase it. • It is a good idea to practice spraying onto a piece of plain, white paper until you find the volume that is best for you.
NB – To deliver the best possible tanning results, we strongly recommend attending sienna X accredited training. Call 0333 600 1200 to find out more.
Fig.2
Increase solution
Fig.1
Round Pattern
Horizontal Pattern
Vertical Pattern
5
Decrease solution
L1760 05 12_Layout 1 08/05/2012 13:45 Page 6
Troubleshooting
“There is no tanning solution coming out of the spray gun” 1. Check there is enough solution in the spray gun Container (10). 2. Make sure the spray gun is not clogged up with old tanning solution. Follow Cleaning and Maintenance instructions.
“Tanning solution is too runny” 1. Spray volume maybe too high. It can be adjusted with the Flow Adjuster Dial. Scroll downwards to reduce the amount of solution (Fig.2). 2. When spraying, hold the spray gun further away from your client’s body or move the spray gun faster. 3. You may not be spraying evenly. Keep the spray gun moving and do not overlap those areas already spray tanned. “Tanning solution sprays irregularly” 1. The solution volume maybe too low and this can be adjusted with the Flow Adjuster dial by scrolling upwards until you get the desired volume (Fig.2).
“The tan is patchy” 1. Ensure your client has exfoliated before spray tanning. 2. Ensure you spray tan in a methodical way to cover all areas. It is easy to see which parts have been sprayed. Keep the spray gun moving and do not overlap those areas already spray tanned. 3. Ensure that you spray tan lightly and in layers rather than one thick layer.
Cleaning & Maintenance
Always wash out your spray gun at least at the end of each day. If the tanning solution dries inside the spray gun, cleaning will become more difficult and the spray gun may become inoperable. To wash out your Spray Gun
● ● ● ●
●
● ●
Switch off and disconnect the motor unit from mains supply. Unscrew the container from the main body of the spray gun. Pour any excess solution back into its orginal container for future use. Half fill the container with water and re-fit it to the spray gun main body, shake the spray gun lightly, re-connect the motor unit to the mains supply and spray the water through the gun. Repeat several times until the water is clear with no traces of tanning solution. Continue to spray the clean water until the container is empty. Run the spray gun for a further 2 minutes with just the air blowing through it. This will dry the inside of the spray gun preventing any contamination of the working parts. Clean any traces of tanning solution from the outside of the gun with a damp cloth. Wipe clean the Lid Seal (8) inside the lid of the spray gun.
6
L1760 05 12_Layout 1 08/05/2012 13:45 Page 7
Mains Connection
This unit is a Class II appliance which means it is double insulated for your protection, no earthing wire is necessary. If the supply cord is damaged, it must be replaced by the manufacturer or our appointed agents. Your unit has been supplied with a mains lead with a fitted plug. This is identified by the fuse holder in the base of the plug. Please read the following safety instructions before use. 1. If the fitted plug is cut off from the mains lead then the plug must be disposed of safely. NEVER under any circumstances insert such a plug into a 13 Amp socket. 2. NEVER under any circumstances use the appliance or mains lead without the fuse cover fitted. This is the little cover fixed into the base of the plug to hold the fuse in place. 3. If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline. 4. A replacement fuse must be rated at 5 Amp. These must be manufactured and approved to BS 1362. 5. IF IN ANY DOUBT CONTACT A QUALIFIED ELECTRICIAN. If you are using an extension lead it must be rated at a minimum of 6 Amps and fully unwound. Do not operate with a lead rated at less than 6 Amps as this will cause premature failure of the motor which is not covered by the guarantee.
INFORMATION ON THE DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT KNOWN AS WEEE Your attention is brought to new directives applicable to the disposal of this electrical equipment, where in accordance with the legislation this product must not be disposed of in your normal household waste. Instead it is your responsibility to dispose of this type of waste by handing it over to special designated collection points for recovery and recycling. This product is marked with a ‘Wheelie bin’ symbol with a cross on it to remind you of this action. The objective of this directive is to help conserve resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste please contact your local authority, take back facilities are free of charge.
The EC Declaration of Conformity
We declare that the unit: True Mist (TS50) conforms to LVD 2006/95/EC, EN 60335-2-23, EN 60335-1, EMF EN62233; EMC 2004/108/EC, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.
Tim Hopper Technical Director
Registered Design No: GB 3022947, EU 000608856, US D563,503S, ECD 001235139 Copyright & Design Right Reserved © 2012
Warranty There is a full 6 months warranty on your Professional Tanning System against faulty manufacture and materials, from date of purchase. This is offered over and above your normal consumer statutory rights. This warranty does not include damage to the product caused by incorrect use.
7
L1760 05 12_Layout 1 08/05/2012 13:45 Page 8
Sienna-X The Spray Tan Cubicle Co Ltd, Unit B Sherriff Street Commercial Complex, Sherriff Street Worcester, WR4 9AB Email:
[email protected] Tel: 0333 600 1200 and +44 (0) 1905 727 070 Fax: +44 (0) 1905 27080
© 2012
L1760 05/12
