Transcript
Instruction Manual
w ww.u l t i m a t e p e rsonalshaver.com Distributed by B.M.S. Enterprises
Congratulations on your purchase! Get ready to experience the closest, most intimate shave you’ve ever had. To get the most out of your Ultimate Personal Shaver, please take a moment to read ALL the following instructions. Once you become familiar with the proper trimming/shaving techniques and maintenance of your shaver, you’ll never go back to conventional shaving ever again. TIP: To achieve the smoothest shave possible, remember to ensure skin is completely dry before shaving. Use plenty of talc powder to prevent nicks and burning.
Included in the Ultimate Personal Shaving System: 1) Ultimate Personal Trimming Shaver 2) Ultimate Personal Finishing Shaver 3) Brush for applying Talc
Lets Get Shaving!
A Smooth Finish
Your Ultimate Personal Trimmer is used for cutting longer hairs right down to stubble. The trimmer does most of the work: this is the most important step in the shaving process, as the Finishing Shaver will not work properly if this step has not been completed. 1. Be sure your skin is dry. 2. Use the large Talc Brush to apply the enclosed Shaving Talc or baby powder. 3. Pull skin tight (for a closer shave). 4. Hold the Ultimate Personal Trimmer at a 45-degree angle to the skin. 5. Reapply powder as needed. 6. Once the longer hairs have been trimmed, reapply powder and move onto A Smooth Finish TIP: Skin absorbs water so always shower or bathe after shaving.
Your Ultimate Personal Finishing Shaver is used to remove stubble and leave nothing but silky-soft smooth skin. 1. Reapply powder. 2. Pull skin tight (for a closer shave). 3. Rotate the Ultimate Finishing Shaver over the desired area (the area that has already been trimmed with the Trimmer). Rotate in a circular motion and up & down. The Ultimate Finishing Shaver will shave all hairs regardless of the direction of growth. 4. Reapply powder as needed. TIP: As you become more proficient with using your Ultimate Personal Shaver, you will find yourself using the Trimmer to get the job done right.
Shaving With Stencils
4) Brush for cleaning shavers 5) Ultimate Shaving Talc 6) Sexy Shaving Stencils
Enclosed you will find a sample of stencils. Use only on dry hair! To use, hair must be ¼ of an inch or longer.
Caring for your Ultimate Finishing Shaver ALWAYS clean the unit with the enclosed mini brush. DO NOT press hard against the Outer Foil of the Ultimate Personal Finishing Shaver as this may break the foil, causing injury to your skin. Before using the shaver, check that the Outer Foil and Inner Blade are not damaged or deformed, as this may damage the skin. DO NOT use the Ultimate Personal Finishing Shaver for any other purpose than shaving the skin. DO NOT to tamper with the shaver as it may malfunction or cause injuries. NEVER wash the shaver in water or use it in a place where it is exposed to any splashes of water. DO NOT place or store shaver in an area with high humidity. A short circuit may occur and will damage the shaver. ALWAYS REMOVE BATTERIES WHEN NOT IN USE!
Caring for your Ultimate Personal Trimmer To clean the trimmer, first remove the battery. Then insert a flat screwdriver into the functional end of the unit and gently twist until the unit separates in half. Use the enclosed mini brush to gently remove any loose particles. Simply snap the halves back together when finished.
Batteries
The Ultimate Trimming Shaver: 1 “AA” Battery. The Ultimate Finishing Shaver: 3 “AAA” Batteries. Always ensure correct polarization (+/-) when inserting batteries. Incorrect polarization will result in reverse blade action and will not cut. When inserting the battery pack into the shaver, make sure that the tracks are aligned. The average battery life is approximately three weeks.
1. Check the size of the stencil. If the stencil is too large, it may need to be cut to size. 2. Pick a stencil and peel it off of the paper. Place the sticky side down over the area you want stenciled. 3. Use the Large Brush to apply Talc or baby powder. Use the Trimmer to trim hair around the outside of the stencil. 4. Apply more Talc or baby powder. Use the Finishing Shaver around the stencil. 5. Remove the stencil when finished.
Part Replacement 1. Before cleaning the Shaver, ALWAYS turn the power switch off (down) and remove the batteries. 2. Remove the Outer Foil by turning it to the right, then gently remove the Inner Blade. 3. Clean the Outer Foil, Innder Blade, and Body Case with the small brush. NEVER tap the driving shaft when cleaning your Shaver. If hair is sticking, use a pressurized air duster (found at local hardware stores). 4. After cleaning your Shaver, replace the Inner Blade and Outer Foil. Make sure to replace the cap to protect your Shaver. If you will not be using your Shaver for some time, apply a few drops of the shaver lubricating oil (which may be purchased online at www.ultimatepersonalshaver.com). Do not use WD-40 or similar products as they will cause serious skin irritation or allergic reaction.
www.ultimatep e r s o n a ls h a v e r. c o m
The Inner Blades and the Outer Foil Should be replaced at the same time every 2-3 years.
Cap (lift up) Outer Foil Inner Blade Driving Shaft On / Off Switch Body Case The Inner Blade and Outer Foil replacements and shaver oil may be purchased online at www.ultimatepersonalshaver.com
Imported by:
