Transcript
„AP-‐01A“
IceAge II Professional Ice Maker
INSTRUCTION MANUAL
Thank you for purchasing the Ice Factory. Please read this instruction thoroughly before your first use of this product. Keep this manual carefully for future use.
Product Description 1. The BT-‐25BTS Ice Factory is a elegant, portable, well-‐designed ice maker. 2. It’s micro computerized system makes the whole process of ice cube making completely automatic. BT-‐25BTS is designed for using external water inlet pipe for water supply, and as well for manual water filling. 3. The advanced “ZEL” compressor and cooling system can product ice cubes in high speed and good quality. Daily ice cubes production is max. 20 Kg. 4. Three different size of solid ice cube are available for selection 5. Its Intelligent System keeps all ice cubes in consistent size by adjusting the duration of ice cube making process automatically according to room temperature. 6. This unit are equipped with self-‐defected detector and protective devices. 7. Its unique design and portability can complement you at Bar, Party Gathering, Yachts, Office or wherever you need.
Technical Specifications MODEL: VOLTAGE: FREQUENCY: POWER: CLIMATE: INSULATION FOAMING:
BT-‐25BTS DIELECTRIC PROTECTION CLASS: I 220-‐240V~ RATED CURRENT: 1.3A 50Hz REFRIGERANT/CHARGE: R134A/110g 200W ICE MAKING CAPACITY: max. 20kg/day. N.ST WATER INLET PRESSURE: 0.1MPa -‐ 0.3 Mpa POLYURETHANE
Parts Diagram
1: Water Tank 2: Ice Cube Tray 3: Ice Baffle 4: Ice Maker 5: Control Panel 6: Switch Panel 7: Water Inlet Valve 8: Tap Water Connector 9: Lip Cover 10: Compressor 11: Water Pump 12: Condenser 13: Evaporator 14: Thermo Sensor 15: Mini Water Level Sensor 16: Maximum Water Level Sensor
Control Panel Diagram 1
2
3
4 • • • •
Power On Indicator Ice Full Indicator Low Water Indicator Power ON/OFF Button
Enclosed Accessory Instruction Manual & Ice Shovel (3 sets)
How to use 1. Remove all packaging materials and labels. Keep the unit at up-‐right position while lifting up from the packaging to avoid causing damage to the compressor of the unit. The tilt angle can not greater than 45 Degree. 2. Place the Ice Station at up-‐right position. Keep the unit at least 20CM apart from the wall around for better ventilation and operation. 3. Wash the Water Tank; Cooling System, Ice Cube Tray; Ice Shovel of the Ice Station with washing detergent before each use. 4. Open the Lip Cover, fill the Water Tank with drinking water. When adding water, make sure the water level does not exceed the maximum water level of the Water Tank. If you use the external Water Pipe for adding water, make sure the Water Pipe is firmly connected with the In Coming Water Inlet, open the tap and check to ensure no water leaking in the conjunction part before use. 5. External Water Inlet Installation diagram Water Inlet Connector Water Pipe Valve 3 way water connector Caution: When using external water source, be sure to use a water pressure reducer! 6. Plug in the unit to the power outlet, the Power On Indicator will light, indicating that the machine is in standby status. 7. Control Panel Diagram Power On Indicator Ice Full Indicator Lack Water Indicator Power On/Off Button Select Button ( Ice Cube Size ) 8. Press the “Power On/Off” button in the Control Panel to “On” position to start the operation. During the operation, press the “Power On/Off” button to “Off” position to stop the unit from running. 9. After the unit running for few minutes, the temperature of the unit and water starts dropping, as the flowing water temperature reach zero degree, the water become frozen, the indicated size will blink. Ice cubes making are now in progress. 10. 36 pieces of ice cubes will fall into the Ice Cube Tray automatically for each cycle. Once all ice cubes are shoveled, the ice cube making cycle starts again. 11. When the Ice Cube Tray is full, the “Ice Full” Indicator will blink, the compressor and fan motor will stop running. Remove the ice cubes from the Ice Cube Tray. The same Ice cube making cycle will starts again.
Duration of ice cube making apprx. 12-‐18 minutes
Maintenance 1. Always keep the unit stand still at up-‐right position while moving to avoid causing damage to the compressor of the unit. 2. Plug the unit into a power outlet alone. Make sure your electricity supply is 187-‐242V~50Hz, the current is 10A. 3. To disconnect the power, grip the plug and pull it from the wall outlet. Never drag the cord. If the power cord is damaged, bring it to the service centre for replacement. 4. The unit should be placed vertically. Do not place the unit near flammable items or fire source. Keep at least 20cm distance from the surroundings for better ventilation and operation. 5. Initially when switching “On” the unit, it will takes sometimes before water is cooling down to zero degree. Duration of ice cube making will be prolonged if adding more water. 6. If the water level is lower than the minimum water level of the Water Tank, the “Lack Water” indicator will light, indicating manual water filling is required. If using external water inlet pipe for water supply, the “Lack Water” indicator will blink, indicating water filling starts automatically. 7. Use only drinking water to make the ice cube. Never use dirty water as it may damage your health. Clean the unit frequently after each usage. 8. Clean the water ejector if water is not flowing well. 9. Install the “Ice Cube Tray” in correct position to avoid touching the Ice Shovel 10. If no water is adding to the unit when the “Lack water” indicator light up, the unit will stops running automatically. 11. Always keep the sensors clean from rust for better performance. 12. Do not open the Lip Cover of the unit during running as it may affects the ice cubes making performance. 13. Unplug the unit from the power outlet and remove all ice cubes before cleaning. Use a dilute solution of water and vinegar to clean the interior of the ice maker, and then rinse it with drinking water thoroughly. Do not rinse internal components of this unit. Do not use gasoline to wash this unit. 14. Remove the Drain Plug from the unit to drain the remaining water from the water tank and let it clean and dry when the unit will not be used for a long period. 15. When using the external water pipe for water supply, the unit will stops running if there are no water supply coming from the pipe.
Trouble Shooting Before bringing to the service centre, please check the followings:
Problems The compressor makes some unusual noise when the “Power On Indicator” is “On”
Possible Reasons Incorrect power supply.
Solution Unplug the unit, and check to ensure correct power supply is used.
The “Power On Indicator” does not light
– No power supply – Bad contact with the power outlet
Check both the power cord, power plug and power outlet
The “Ice Full Indicator” keeps on blinking
Ice Baffle are blocked by ice cubes. It can not works properly
Remove the ice cubes, turn off the ice maker. And then turn on again
NOTE:
Please contact our service centre for replacement if problems are not caused by the above reasons.
The unit is in normal good condition if the following occurred • The fan is still running for few seconds after switching “Off” the unit and the compressor. • Noise caused by the running compressor and the flowing refrigerant inside the compressor.
BETEC · Herzogstr. 55 · D-‐63263 Neu-‐Isenburg Phone +49 (0) 61 02 / 310 67 · Fax +49 (0) 61 02 / 32 08 59 www.BETEC-‐Ideen.de · E-‐mail: info@BETEC-‐Ideen.de © BETEC Art.Nr./Part-‐No. 4046
