Preview only show first 10 pages with watermark. For full document please download

Instruction Manual Www.vax.co.uk Vax Careline: 0870 6061248

   EMBED


Share

Transcript

V-040_Ultrixx.qxd 11/4/06 13:22 Page 2 Vax Careline: 0870 6061248 www.vax.co.uk UPRIGHT VACUUM CLEANER Vax Model Number: V-040 Instruction Manual Please read carefully before using the vacuum cleaner. Always fully extend the mains cable before use. V-040_Ultrixx.qxd 11/4/06 13:22 Page 3 Parts Overview 1. Diagram FRONT BACK 1 2 17 3 18 4 19 5 16 6 26 20 7 8 15 21 9 10 25 22 11 12 13 14 24 23 23 Fig.1/1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2 Handle Grip Handle TurboTool caddy TurboTool Hose Dust Container Release Button Carry Handle Dust Container Filter Dust Container Quick Release Dust Container Headlight Carpet Height Adjust Dial Brushbar Furniture Protector 15 16 17 18 19 20 21 22 23 24 25 26 Extension Tube Crevice Tool (inside extension tube) Cord Guide Hose Caddy Cord Wrap With Quick Cord Release Long Power Cord Hose Extension Tube Lower Cord Wrap Castors Handle Release Pedal On/Off Pedal Dusting Brush V-040_Ultrixx.qxd 11/4/06 13:22 Page 4 Accessories Accessories 1 2 Fig.1/3 1 Dusting brush 2 TurboTool 3 V-040_Ultrixx.qxd 11/4/06 13:22 Page 5 Safety Information 2. Safety Information 17.Keep vacuuming area well lit. FOR HOUSEHOLD USE ONLY. When using the vacuum cleaner, basic safety precautions should always be observed, including the following: 18.Store the vacuum cleaner indoors in a cool, dry area. 1. Only use the vacuum cleaner indoors on dry surfaces. 2. Turn off the vacuum cleaner controls before connecting to or disconnecting from the mains supply. 3. Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose. 4. Close attention is necessary when used by or near children. Do not allow children to use as a toy. 5. Use only as described in this manual. Use only the manufacturer’s recommended attachments. 6. Do not use the vacuum cleaner if it has been dropped, damaged, left outdoors or dropped into water. Do not use the vacuum cleaner with a damaged cord or plug. If the supply cord or plug is damaged, return the vacuum cleaner to a Vax Authorised Service Agent or suitably qualified person for examination, repair or adjustment. 7. Do not pull or carry by the cord. Do not use the cord as a handle, close a door on the cord or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces. 8. Do not handle the plug or vacuum cleaner with wet hands. Do not use outdoors or on wet surfaces. 9. Do not put any objects into openings. Do not use with any openings blocked and do not restrict air flow. Keep all openings free of dust, lint, hair or anything that may reduce airflow. 10.Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts. 11.Do not pick up hot coals, cigarette butts, matches or any hot, smoking or burning objects. 12.Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc) or use in the presence of explosive liquids or vapours. 13.Do not vacuum up harmful or toxic material (chlorine bleach, ammonia, drain cleaner, etc). 14.Do not vacuum up hard or sharp objects such as glass, nails, screws, coins, etc. 15.Do not use without the filters in place. 4 16.Take extra care when vacuuming on stairs. 19.Turn off the switch before unplugging. 20.Use only CE-approved 13 amp extension cords. Non-approved extension cords may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over. WARNING: Always switch off and unplug the vacuum cleaner from the electrical outlet before assembling, opening or emptying the dust bag, or before connecting/disconnecting the attachments. CAUTION: The vacuum cleaner is a very powerful unit. Before plugging the cord into the outlet make sure the switch is in the ‘off’ position. Hold the vacuum cleaner firmly when starting and in use. IMPORTANT: If the inlet or hose is blocked, switch off the vacuum cleaner and remove the blockage(s) before re-starting the vacuum cleaner. IMPORTANT: Changing the dust bag and filters regularly improves vacuum performance. This vacuum cleaner is intended for household use only and not for commercial or industrial use. PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE. Motor Thermostat IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason, the vacuum cleaner should over-heat, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum vacuum cleaner from the electrical outlet and turn off the switch. Remove the dirt container and empty. Clean the filters. Allow the vacuum cleaner to cool for approximately one (1) hour. To re-start, plug into an electrical outlet and switch back on. V-040_Ultrixx.qxd 11/4/06 13:22 Page 6 How to Assemble/How to Operate 3. How to Assemble 1. Slide the back panel onto base. To secure, insert two screws into the back of the back panel. (Fig 3/1) Phillips screwdriver required 4. Wrap the hose around the back of hose caddy (Fig 3/3). Push the hose tube down into the right hand side of the vacuum cleaner (Fig 3/3). Set aligning tab on button of dust container into rectangular slot on vacuum cleaner (Fig 3/3). Rotate dust container into vacuum cleaner and push to fit into place (Fig 3/3a). Fig.3/4 A C B Fig.3/1 2. Handle (back) and TurboTool caddy (front) assembly. Place upper handle onto top of vacuum cleaner (Fig 3/2). Push TurboTool caddy onto the front of vacuum cleaner. Insert the two screws into the back of the handle and tighten, making sure the handle is secure. Fig.3/2 5. To attach the accessories, slide the dusting brush (A) into the hole on the tool caddy with bristles facing out (Fig 3/4). Slide the extension tube (B) and crevice tool (C) (stored inside the extension tube) through the ring on the front right side of the tool caddy. Clip the TurboTool (D) onto the TurboTool caddy (Fig 3/4) 4. How to operate 3. Secure back hose, wrap hose around back of hose caddy (Fig 3/3). Push hose wand down into the right side of vacuum cleaner (Fig 3/3). Set aligning tab on bottom of dust container into rectangular slot on vacuum cleaner (Fig 3/3). Rotate dust container into vacuum cleaner and push to fit into place (Fig 3/3a). WARNING: FULLY ASSEMBLE BEFORE OPERATING. 1. Turn the Quick Cord Release for easy cord removal (Fig 4/1). 2. Turn the carpet height adjust dial to match the surface being cleaned (Fig 4/1). IMPORTANT: FOR EASIEST ADJUSTMENT, PLACE VACUUM CLEANER IN THE FULL UPRIGHT POSITION. Fig.4/1 Fig.3/3 A TAB SLOT Fig.3/3a 3. Plug the cord into electrical outlet. Turn vacuum cleaner on by depressing foot pedal located on the back left side of the vacuum cleaner. To release handle, push the handle release pedal located on the lower left side of the vacuum cleaner. Move the handle and adjust it to the desired position for (a) operating the vacuum cleaner, and (b) lowering handle to clean under furniture. NOTE: Rotating brush could cause area rug fringe to become tangled within vacuum cleaner. Use caution when vacuuming throw rugs with fringe. 5 V-040_Ultrixx.qxd 11/4/06 13:22 Page 7 How to Operate/Dust Container & Filter: Removal & Replacement 4. The vacuum cleaner must be in its upright position to raise brushbar. Remove the hose from the tool caddy. Choose any of the accessories or use the hose alone. Simply push the attachment firmly onto the end of the tube or hose handle. To remove the tool, twist and pull apart gently (Fig 4/2). Fig.5/1 Fig.4/2 Remove the foam filter from the dust container. Hold filter under running water to wash. Ring excess water and allow to dry for at least 24 hours before replacing and using the vacuum cleaner (Fig 5/2). 5. If additional length is needed, use the extension tube and crevice tool. Pull crevice tool out of extension tube and fit on to the end of the extension tube. Use extension tube and crevice tool together or separately (Fig 4/3). 6. Use the carry handle on the dust container to move the vacuum cleaner from room to room (Fig 4/3). NOTE: Ensure dust container is secured in place before lifting the vacuum cleaner. Fig.4/3 5. Dust Container & Filters: Removal & Replacement WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING. NOTE: Unplug vacuum cleaner before changing filter. NOTE: Rinse foam filter once every month. If vacuum is used frequently, the filter may require more frequent cleaning. NOTE: For best performance, replace pleated filter yearly. 1. Press dust container release button on front of vacuum cleaner to remove the dust container. Hold dust container over dustbin and press the quick release button to empty. Snap dust container bottom back into place after emptying (Fig 5/1). 2. Twist and lift to remove dust container (Fig 5/1). Tap the lid on the inside of a dustbin to remove excess dust from the filter. IMPORTANT: Do not rinse the filter with water. 6 Fig.5/2 3. To replace foam filter return filter to dust container by placing on top of screen inside dust container. IMPORTANT: DO NOT RETURN FILTER TO THE DUST CONTAINER BEFORE IT HAS COMPLETELY DRIED. Hold the dust container lid and grasp the filter tab. Pull away from lid. 4. Return the filter to the dust container lid. Push filter into place until it snaps to prevent leakage. Align tabs on lid with the openings on the dust container and twist to close and secure lid. Return dust container to vacuum cleaner. Align slot on bottom of dust container with tab on vacuum cleaner. Push to snap into place (Fig 5/3). Fig.5/3 V-040_Ultrixx.qxd 11/4/06 13:22 Page 8 Belt or Brush Removal and Replacement/Light Bulb Replacement/TurboTool: Clearing Blockages 6. Belt or Brush Removal and Replacement 8. TurboTool: Clearing Blockages 1. Lay vacuum cleaner flat and turn over to expose nozzle base. Base should lay flat and face up. To remove nozzle guard, use Phillips screwdriver to remove the three screws. Arrows show location of screws. Rotate/pivot the nozzle guard and pull off. Lift and remove brushbar. Dispose of old belt (Fig 6/1). Rotate locking ring 180˚ and turn TurboTool over. Pivot lower housing and remove clog. To reassemble, be sure tabs are engaged. Pivot the lower housing closed. (Fig 8/1). Fig.8/1 Fig.6/1 2. To replace belt or brushbar, slide belt onto motorshaft. Place new belt in area of brushbar without bristles (Fig 6/2). Fig.6/2 Slide belt onto motorshaft. 3. With new belt in place, pull and slide brushbar into nozzle making sure that the brushbar caps are in the correct orientation (Fig 6/3a). Rotate brushbar manually to make sure belt is properly aligned. Secure by aligning the four tabs in the base slots. To re-attach nozzle guard, rotate/pivot back into position. Replace all three screws to secure nozzle guard. Fig.6/3 TABS Fig.6/3a 7 V-040_Ultrixx.qxd 11/4/06 13:22 Page 9 Troubleshooting 9. Troubleshooting WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG VACUUM CLEANER BEFORE SERVICING PROBLEM: Vacuum cleaner won’t run Cause: Not properly plugged into outlet. Solution: Plug unit in firmly. Cause: Blown fuse/tripped breaker. Solution: Reset circuit breaker or replace fuse. Cause: Needs service. Solution: Take to service centre. To find nearest location, visit our website at www.vax.co.uk or call 0870 6061248 PROBLEM: Vacuum cleaner won't pick up/loss of suction Cause: Dust container not installed correctly. Solution: Review dust bag removal and replacement. Cause: Dust container full or blocked. Solution: Empty dust container. Cause: Brushbar worn. Solution: Replace brushbar. Cause: Broken or worn belt. Solution: Replace belt. Cause: Clogged filter. Solution: Remove filter and clean. Cause: Nozzle/dust passage hose clogged. Solution: Check lower hose for obstruction and remove obstruction. Cause: Carpet height setting is incorrect. Solution: Set carpet height adjust dial to appropriate setting for carpet being cleaned. PROBLEM: Dust escaping from the vacuum cleaner Cause: Dust container full. Solution: Empty dust container. Cause: Dust container not installed correctly. Solution: Review dust container removal. Cause: Dust container full. Solution: Empty dust container. Cause: Clogged filter. Solution: Remove filter and clean. PROBLEM: Accessories won't pick up Cause: Hosed clogged. Solution: Remove hose and tools; remove blockage. Cause: Dust container full. Solution: Empty dust container. Cause: Clogged filter. Solution: Remove filter and clean. 8 V-040_Ultrixx.qxd 11/4/06 13:22 Page 10 10. UK Service & Help Vax Care 0870 6061248 Monday-Friday. 9.00am to 5.00pm. An answerphone will be available out of these hours. Any queries or concerns about using your Vax, call the Vax Careline. Calls are charged at the UK national rate. Please make a note of the model number and serial number of your Vax before calling. There are over 400 approved Vax Service Agents in the UK. For the nearest Vax Service Agent, please call the Vax Careline or visit www.vax.co.uk 11. Technical Specification Voltage: Wattage: Capacity: Filters: 220 ~ 240V 50Hz 1450W Nom. 1650W Max 2.4 litres Fibre pre-motor filter Pleated paper post-motor filter Cord length: 9.25m Weight: 8.4kg Subject to technical change without notice. 9 V-040_Ultrixx.qxd 11/4/06 13:22 Page 1 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declares that the product V-040 Ultrixx upright is manufactured in compliance with the following Directives: Safety: 72/23/EEC and 93/68/EEC Low Voltage Directive EMC: 89/336/EEC Electromagnetic Compatibility Directive Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK email: [email protected] - website: www.vax.co.uk 10