Transcript
INSTRUCTIONS TWO HANDLE LAUNDRY FAUCET 06-4480
TROUBLE-SHOOTING A
B
C
D
E
If you’ve followed the instructions carefully and your faucet still does not work properly, take these corrective steps.
PROBLEM
PROBLEM
Leaks underneath handle.
Your new Taymor faucet will give you years of trouble-free performance. Thank you for choosing our product for your home. Please read all of these instructions carefully before installing your new faucet.
Faucet leaks around connect.
CAUSE
Connect incorrectly fitted.
ACTION
ACTION
1. Move the handle to the off position. Unscrew the handle screw (#1) and remove the handle (#2 or #16) (Figure A). 2. Tighten the bonnet (#4) by turning it clockwise (Figure B). Move the cartridge stem (#5) to the on position. The leak should stop draining out from around the cartridge stem. 3. If the leak does not stop, shut off the water supply. Remove the bonnet by turning it counter clockwise. Lift out the cartridge valve (Figure C). Inspect the smaller O-Ring (#6) on the cartridge stem and the valve seat (#7) on the cartridge stem. Remove any debris from the O-Ring and the valve stem. If the O-Ring is twisted, straighten it out. If the O-Ring or valve stem is damaged, replace it. 4. Postion the cartridge back to the faucet body. Tightly screw the bonnet onto the faucet body. 5. Re-install the handle.
TOOLS REQUIRED
1. Unscrew the adaptor (#15) by turning it counter clockwise (Figure D). Inspect the black rubber washer inside the adaptor. The rubber washer should be flat. 2. Screw the adaptor onto the spout end and tighten.
PROBLEM
Improper water pattern.
CAUSE
Adaptor dirty or small parts inside adaptor improperly installed.
ACTION
1. Remove the adaptor (#15) from the spout end by turning it counter clockwise. 2. Gently flush the small parts inside the metal screen to clear away any debris. 3. Re-install the small parts as shown in the exploded diagram (Figure E). Metal screen must be flat. 4. Screw the connect onto the spout end and tighten.
CUSTOMER SERVICE e as t 1-800-387-7064
w e s t 1-800-267-4774
Maintenance
Your new Laundry faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and void your warranty.
· Pipe wrench · Basin wrench · Crescent wrench · Teflon tape · Plumber putty · Screwdriver · Braided supply lines · Flashlight · Safety goggles
CAUSE
Bonnet has come loose or O-Ring on cartridge is dirty.
www.taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD. VANCOUVER, BC V3M 6K8 • TORONTO, ON M3J 2R1
INSTALL FAUCET
14 - spout 1
13 - ring
12 - O-RINGS
Shut off water supply. Remove old faucet, taking care not to damage existing water lines. Clean surface in preparation for new faucet. Always wrap metal threads with Teflon tape before connecting water lines.
15 - adaptor
11 - NUT 2
10 - screw cap
STEEL LAUNDRY SINK
2
Place the bracket (#18) in position on the sink. Install with screws and nuts (not included) onto the sink. Tighten the nuts with wrench.
9 - NUT
CEMENT LAUNDRY SINK Place the bracket (#18) and the support (#19) in position on the sink. Through the hole in the support install the screw (#20) into the bracket. Tighten nut (#9). Flip bracket for installation on thinner sinks.
16 - handle (blue) 8 - screw 17 - screw 7 - valve seat 6 - o-ring
3
5 - stem
19 - SUPPORT
4 - bonnet 18 - BRACKET
4
20 - screw
3 - BUSH
1 - SCREW
2 - handle (red) OR
Place the new faucet in position on the bracket. From under the faucet, install screw into bracket. Thread the nut (#9) onto the screw (#17) and tighten. Ensure bracket makes contact with bottom of faucet body (this helps stabilize the facuet).
Place the new faucet in position on the bracket. From under the faucet, install screw (#17) into bracket. Thread the nut (#9) onto the screw and tighten. Ensure bracket makes contact with bottom of faucet body (this helps stabilize the facuet).
3
A) Stainless Steel Braided Faucet Supply Tubes: This is the simplest of all installations. If you are using stainless steel braided faucet supply tubes, this faucet requires one end of the supply tube to have a 1/2” female IPS connection. The other end of this supply tube must match the thread on the water supply fittings or shut off valve under your sink. Once you have identified the required tube, carefully follow the manufacturer’s installation instructions for each tube. B) Ball Nose Flexible Supplies: If you are using ball-nose flexible supplies to connect the faucet to water supply lines, slip coupling nut (not included) behind ball-nose of flexible supply tube. Ball nose coupling will go partially into IPS shank or fitting. Tighten coupling nut (DO NOT OVER TIGHTEN). Install opposite end according to manufacturer’s instructions for both tubes.
5
Important: After installation is complete, remove adaptor (#15). Turn on water supply and allow both hot and cold water to run for at least one minute each. While water is running, check for leaks. Replace connect. Tighten connecting nuts slightly to stop minor leaks. If problems persist, refer to trouble-shooting chart.
