Transcript
Installation/Wiring
DC Motor Control for Phantom and Orbiter by Draper Electrical Specifications—DC Motor Control
Caution
Input:
① Make sure electrical supply has been disconnected before attempting to connect Lift to electricity. ② Unit operates on 12V DC. ③ Lift must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code(NEC), NFPA 70. All operating switches should be “off” before power is connected. ④ Lift should be operated and checked prior to installing projector. ⑤ Unit must be installed by qualified personnel.
DC Voltage 11.5-36VDC
Output: Same voltage as input, 7.0 FLA Max. Signal output is Class 2. Make sure the total FLA of all motors connected together does not exceed the load carrying capacity of the this control. This device has not been evaluated for reliability to the Standard for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991 and therefore not considered suitable for entrapment protection.
DC Motor Control Wiring Diagram for Phantom (-) DC CONVERTER
BL
BL
OUTPUT: 24 VDC 2.1 Amp
(+) BN
BN
LINEAR ACTUATOR 24 VDC AUX PORT- For connecting multiple controls together (up to six totalconnect from AUX to Eye).
DC Motor Control Mounting Box (included)
Black wire with white type DC Motor Control EYE PORT- For IR EYE; RF Receiver or LED Switch. If more than one of these three is used with control, a splitter is required.
DASHED LINES INDICATE WIRES PROVIDED BY INSTALLER
DOWN - BLACK COM - WHITE UP - RED
STOP
25/8"
WALL SWITCH 3 BUTTON
DC Motor Control Wiring Diagram for Orbiter D2
LS2
D1
15/16"
LS1
BL
BL
BN
BN
(-) (+)
WH 24 VDC MOTOR
DC CONVERTER OUTPUT: 12 VDC 1.25-1.5 Amp
Black wire with white type
AUX PORT- For connecting multiple controls together (up to six totalconnect from AUX to Eye). DASHED LINES INDICATE WIRES PROVIDED BY INSTALLER
DC Motor Control EYE PORT- For IR EYE; RF Receiver or LED Switch. If more than one of these three is used with control, a splitter is required. DOWN - BLACK COM - WHITE UP - RED
STOP
WALL SWITCH 3 BUTTON
Spring-Loaded Terminals When running wires to the spring-loaded terminals, use the following steps: ➀ Strip outer wire sheathing back 1", then strip insulation of individual wires back 3/8". ➁ Place screwdriver into the top slot to open the spring-loaded terminal. ➂ Slide wire into terminal connection point. ➃ Remove screwdriver. Wire is now locked into place.
RS232 Note: Operating a Phantom or Orbiter via RS232 requires an R2D7. See separate R2D7 RS232 instructions for details.
Please Note: Cable used to connect to the Eye jack must be electrically straight 6-conductor modular cable (RJ25). This means colors do not cross over: blue leads to blue, green to green, etc. (see diagram below). PIN 6
CORRECT Tab facing away (down)
BLUE YELLOW GREEN RED BLACK WHITE
PIN 1 WHITE BLACK RED GREEN YELLOW BLUE
Tab facing away (down) PIN 6
PIN 1
INCORRECT R2D7 Tech
7 v2simple de R2D y ma
nolog
DC Motor Control Eye Port Prog Light
3½"
PIN 6
RS232 Adapter
SYS 4 SYS 53 RS-232 SYS 6 SYS 71 SYS 2 SYS SYS N MAI
To PC
2 7 vsimple R2gyDmade
nolo
h Tec
SYS 6 SYS 71 SYS 2 SYS MAIN
®
Copyright ©2012 Draper Inc. Form DCMotorControl_TechDataSheet12 Printer in U.S.A.
Tab facing away (down)
PIN 1 WHITE BLACK RED GREEN YELLOW BLUE
WHITE BLACK RED GREEN YELLOW BLUE
Tab facing away (down) PIN 6
PIN 1 COLOR WHITE BLA L CK RED GREEN YELLOW BLUE
PIN # 1 2 3 4 5 6
FUNCTION R CLOCK RQ COMMON +5VDC 5VDC R DA RQ D TA RP DA D TA +12VDC 12VDC
If you encounter any difficulties installing the DC Motor Control, call your dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.
