Transcript
Integrated Positioning System Quick Manual
Model ZC-PT437 / ZC-PTW437
1. Safety Regulations The purpose of the Safety Regulations is to prevent the risk of damage to the property and user’s health. Not following the instruction may result in
Not following the instruction may result in injury
severe injury or death.
or property damage.
WARNING
CAUTION POWER
WARNING ◆Please check the external connection terminal first, when connecting the power. - Incorrectly connecting the power supply can cause fire, electric shock, or product failure. ◆Stop using the product, when there is smoke or strange smell from the product. - In this case, immediately disconnect the power and contact the service center. Continued use may cause fire or electric shock. ◆Disconnect the power plug when there is lightning and storm. - It may cause fire or product failure.
CAUTION ◆Securely fasten the power cord to power connection terminal before use. - Unstable connection may cause fire.
INSTALLATION
WARNING ◆Must use the adapter that is provided when you purchased our product. - Using other adapters may cause fire, electric shock, or product failure.
CAUTION ◆Please fasten the camera securely and firmly to the wall or ceiling. - Insecure installation may cause the camera to fall and result in serious injury. ◆Do not place conductive object (screwdriver, coins, metal objects, etc.) and water containers on top of the camera. - Fire, electric shock, or falling may cause bodily injury. ◆Do not connect multiple cameras to a single adapter. - Exceeding the adapter capacity may cause abnormal heat and fire.
NOTE ◆Do not install the product where there is a lot of moisture, dust or soot. - May cause fire or electric shock. ◆Do not drop any objects on the product or apply strong impact. - Keep away from excessive vibration or strong magnetic influence. ◆Avoid high temperature (50℃ or higher) and low temperature (-10℃(Indoor), -50℃(Outdoor) or below) or high humidity. - May cause fire or electric shock. ◆Keep away from heat vents or heating appliances. - May cause fire or electric shock. ◆If you want to relocate the installed product, be sure to turn off the power before moving and reinstalling. - May cause fire or electric shock. ◆Install at well-ventilated locations. - May cause fire or electric shock.
2. Precautions ■Do not disassemble the camera on your own. ■Always be cautious when handling the camera. ■Do not punch or shake the camera and be careful not to damage the camera with careless storage and misuse. ■Be cautious not to install the camera at rainy or humid locations and do not operate the camera on wet places. ■Gently wipe the surface with a dry cloth. Never use strong chemical substances or detergents.
3. Components
ZC-PT437/ZC-PTW437
Fuse (8A, 1EA)
L-type Wrench (4mm)
Mounts The following items are optional and sold separately.
Quick Manual
Product Configuration Appearance ❶Lens ❷Wiper : wipes the front glass of the housing. ❸Sun Shield ❹Main Body ❺Base Block ❻Housing ❼Communication/ ID Setup Switch Refer to the page 15 of User Manual for details about Switch settings. ❽Video Output Cable [CAP-370, CAP-371,CAP-VAC1]
4. Installation Connecting Lens & Camera
1
2 3 ❶Zoom Camera ❷Camera Control Board
4
❸Wiper Motor ❹Pan & Heater
Connecting Camera Communication Board(Interface Board) Refer to the picture below for the wiring of the product. (Coaxial communication does not require extra wiring.) 1
❶Alarm Output
4
2
❷Alarm Input (1ch ~ 4ch)
5
3
❸Alarm Input (5ch ~ 8ch) ❹Communication Connector
6 ❺Video Connector
7
❻Main Power ❼Illuminator Power
Diagram of Communication/Control Signal(Communication Cable Connected)
Connect to Communication connector as shown below.
·RS-485
·RS-422 Controller or DVR
Positioning
Positioning
Controller or DVR
For more precise text information, refer to the silk screen text of the board.
Connecting Power AC/DC Power does not have polarity. • •
Max. Voltage (30VDC/2A, 125VAC/0.5A, 250VAC/0.25A). A separate relay device is required if you are connecting a device that exceeds the capacity.
•
Connecting the power connector and GND incorrectly to the NC/NO may cause a short circuit and fire, damaging the product.
Communication & Protocol Coaxial communication automatically detects signals, therefore, does not require a separate communication setup process.
SW
Purpose
1
ID
2
Protocol, Communication type, Ack., etc.
Screws Name
Rubber
Camera ID DIP Switch Settings (S1:1~8) Assign a unique number for each camera.
The initial value of the switch is “0”, and all of the 8 switches are defaulted to OFF. Each switch has a unique value, and the ID is the sum of the values of the switches. S1-DIP
1
2
3
4
5
6
7
8
Value
1
2
4
8
16
32
64
128
Example of Camera ID Settings (On:
Off:
)
Ex) 1
Ex) 2
0+0 = 0 (ID = 1*)
2+4 = 6 (ID = 6)
� Use a unique ID for each camera. The summation value is “0”, it is recognized to ID as “1”.
Ex) 3
1+2+4+8+16+32+128 =191 (ID = 191)
Protocol (S2:1~4)
Select a communication Protocol for the camera. No
Protocol
S2-4
S2-3
S2-2
S2-1
0
Automatic
OFF
OFF
OFF
OFF
1
CyberScan-I
OFF
OFF
OFF
ON
2
Pelco-D,Pelco-P
OFF
OFF
ON
OFF
3
SAMSUNG-T
OFF
OFF
ON
ON
4
SAMSUNG-E
OFF
ON
OFF
OFF
5
Panasonic
OFF
ON
OFF
ON
6
Vicon
OFF
ON
ON
OFF
7
Honeywell
OFF
ON
ON
ON
8
AD
ON
OFF
OFF
OFF
9
GE
ON
OFF
OFF
ON
10
BOSCH
ON
OFF
ON
OFF
Convex Protocol & Pelco-C (Coaxitron) can be applied to every protocols.
Baud Rate Settings (S2: 5,6) Select a transfer speed of a selected protocol.
No
Baud Rate(BPS)
S2-5
S2-6
In order to use a third party controller with this
1
2,400
ON
ON
product, please contact our Sales Department.
2
4,800
ON
OFF
3
9,600 (Default)
OFF
OFF
4
19,200
OFF
ON
Communication Response Settings (S2:7) Select a communication response method for the camera and controller: ON or OFF
Communication Method Settings (S2:8) Select a communication method for the camera.
Assembly & Installation
- Initially the DIP Switch is set to OFF, and the default values are presented in the shadowed column.
Using POLE Mount 1. Fix 4 hex screws to secure the pole mount
2. Disassemble base block from the
3. Fix 4 hex screws to secure the base
main body.
on the base.
block on the pole mount. Connect cables and close the plug.
Pole Mount
M8 Screw
Connect Cable Plug Base Block M5 X 15 Reference- Wiring Diagram
4. Fix housing and main body set to the base block. The lower portion and the upper portion of the base block is designed
to
have
only
one
way
direction. The convex portion is the fastening point. (Blind Mating Design)
Pay attention to the direction.
4. Finish the Installation.
Using WALL Mount 1. Fix 4 hex screws to secure the wall
2. Disassemble base block from the
mount on the wall.
body.
main
3. Connect base block cable of the product to the Wall Mount and fix it using 4 hex screws
Washer, nut
M8 Screw
M5 X 15
M5 X 15
Base Block
WALL MOUNT 4. Connect the cables through the bottom
5. Fix housing and main body set to the base
of the wall mount and close the gasket &
block. The lower portion and the upper
plate of the Wall Mount.
portion of the base block is designed to have
6. Finish the Installation.
only one way direction. The convex portion is the fastening point. (Blind Mating Design)
Cover Gasket
Plug
● Do not connect the camera to a power outlet until the installation is complete. Supplying power in the middle of the installation may cause fire or damage the product. Ensure that the housing is closed completely before you turn on the product. Do not reset the system with the housing open. Otherwise, it may cause damage to the product.
Installing the LIGHT BRACKET 1. Cable connection Connect Light adapter to j2 on base block. * Refer to the first image on the right : IR Illuminator Power on Base Block The max. power voltage is 50V/6A. Be careful about polarity when using DC power
2. Fasten 4 hex screws to secure the Light Bracket at the bottom Bracket Fixing hole
side of the camera housing. (4x12, spring washer)
M4 x 12 bolt 3. To secure the light projector on the bracket, fasten 3 hex screws through the holes prepared on the boundary of the bracket, from the bottom side. Fix the center hex screw from the upper side of the bracket mount towards the light projector. *
Mounting
and
securing
the
light
projector
may
vary
depending on the light projector type.
4. Insert the projector cables through the rear hole of the camera. Without completely opening the cable gland, coil it twice, then remove the holder and connect the cable.
Cable Clamp
After connecting, use cable clamp to fix the cable.
Cable
Holder
Gland 5. Illuminator cable is to be connected to the power module on CXP housing board J2. * Refer to the image on the right. : Light power on a camera board of CAP-37x housing.
±(DC) Be aware of polarity Be careful about polarity (+, -) when using DC power
±
Power Supply This system turns on simply by connecting the power. The automatic pre-heating process could be started whenever the device is switched on and the air temperature is below 24℃. This process is used to ensure that the device works properly even at low temperature. The duration ranges between 60 to 180 minutes, depending on conditions. Before Connecting the Power Make sure that system and other components for installation are closed so that it is impossible to come into contact with live parts.
Make sure that all the parts are fastened down firmly and safety condition.
Initial Display When the power has connected to the product, information such as protocol, version and other information will be displayed.
HOMING
AUTOMATIC : 9600 (S)
MOTION : 111103 EXPAND : 110915 CAMERA : 100527
Displays for 2 seconds.
