Transcript
IntelliSound
Table of Contents Controls:.......................................................................................................................... 3 The following is a list of items required for installation:.................................................... 4 Tools Required: ............................................................................................................... 4 Hardware (hardware included): ....................................................................................... 4 Hardware Assembly: ....................................................................................................... 7 Connections: ................................................................................................................... 8 IntelliSound Connections: ............................................................................................ 8 Electrical: ................................................................................................................... 10 Parameters:................................................................................................................... 12 Intellitan® / T-MAX® .................................................................................................... 12 Disabling Audio Source(s):............................................................................................ 12 Unit Software:................................................................................................................ 12 User Interface: ........................................................................................................... 13 To Change Parameters ............................................................................................. 13 Room Controller: ........................................................................................................... 14 Security Levels: ......................................................................................................... 14 Computer Control Level ......................................................................................... 14 Level -1 - Employee Level...................................................................................... 14 Level - 2 - Supervisor's Level ................................................................................. 14 Level 3 - Manager's Level ...................................................................................... 14 CCS IV Displays ........................................................................................................ 14 Compulsory Registration / Liability to Charge (Sound Reproduction): .......................... 17 Warranty:....................................................................................................................... 17
Introduction: The IntelliSound Audio System compliments the Ergoline Ambition and SOLTRON XS Series tanning systems manufactured by JK Products and Services Inc. The IntelliSound provides salon owners the ability to offer a variety of audio listening options to their customers. The IntelliSound system supports the following audio solutions: o
Single Studio Channel Source (i.e. Audio Sources similar to CD players, Audio Cassette Players, etc.)
o o o
MP3 Input FM Radio Station (Four Presets that can be defined by the Salon Owner) Four Digital Music Inputs (i.e. DMX®)
Controls: The controls for the IntelliSound are available on the user interface key-pad.
SOURCE
VOLUME
During idle mode (tanning bed off), the audio being played by the “Studio Channel” source may be heard at a preset volume in the tanning room. This feature can be turned off by the salon owner if desired. The audio will be heard at the pre-set volume set by the Salon owner and cannot be adjusted by the tanning customer. By using buttons on the User Interface Control panel, customers can select the available audio options and control the volume levels. During the session the “RESET” button is used to switch between the available audio options and the “TIME” up/down buttons are used to adjust (increase/decrease) the volume. The audio sources may be selected and the volume adjusted only during a tanning session. The source and volume controls are not available when the tanning system is in session delay or idle. The first available audio option to the tanner is the “Studio Channel”, followed by “MP3”, four preset “FM” stations and finally four “DMX”® channels. If any of these mentioned options are not available in the salon (i.e. Studio Channel or DMX®) the feature may be disabled by setting a parameter on the Intellitan timer (see parameter list on page 11).
The following is a list of items required for installation:
Tools Required:
Phillips screw driver (+) Standard and Stubby
10MM deep well socket and ratchet combination
Cordless Drill
1/4” Drill Bit
Hardware (hardware included): FASTENER ILLUSTRATIONS
Phillips Screw #6 X 3/8
Flat Washer
M8 x 65
Speaker Housing Assembly: The IntelliSound Audio System connects to the tanning system at the head end of the bed. The following instructions and illustrations show the procedure for attaching the IntelliSound Audio Solution to the tanning system: 1. Remove Lower acrylic following the procedure outlined in the illustration below.
Store acrylic in a place so that it is not damaged during the IntelliSound installation process.
Remove the body lamps from the lower section of the tanning system following the procedure outlined below:
Store lamps in a place so that they are not damaged during the IntelliSound installation process.
2. Use the template provided with the IntelliSound components, working from the inside out. Drill out the mounting holes using the ¼” drill bit (Figure A) and use the hardware provided to attach the IntelliSound speaker assembly to the tanning system (FIGURE B and FIGURE C). FIGURE A
FIGURE B
FIGURE C
Hardware Assembly: 3. You may leave the IntelliSound power supply on the floor if desired or mount it to the tanning systems leg using the hole locations with the hardware provided..
Connections: IntelliSound Connections:
The cover of the IntelliSound power supply must be removed to complete its installation. The following procedure should be followed to complete the installation (all cables must be placed through the holes provided): • • • • • • •
Remove the display cable from the Intellitan power board Connect the cable installed in position “B” to the Intellitan power board Connect the cable disconnected from the Intellitan power board to the available location at position “B” in above illustration. Connect the cable from the IntelliSound assembly to the connector available in position “A” in the illustration above. Re-install the cover on the IntelliSound power supply Attach speaker wires to connector “E” in the connections illustration Audio wires from the IntelliSound system should be connected to position “D”
Audio Connections:
C D
A
B D
E
A - Antenna Connection FM B - Right & Left (External Music Source) Studio Channel C - DMX Connection D - Auxilary Audio In (Left & Right) MP3 E - Right & Left Speaker Connection
Electrical:
To avoid personal injury and damage to the electronic components inside the IntelliSound, the power to the tanning system must be turned off before any service is performed. To make the electrical connections for the IntelliSound Audio system to the tanning system, the front façade (lower décor panel) of the tanning system must be removed. The procedure to remove the façade is shown in the illustrations below.
FIGURE A
FIGURE B
The IntelliSound Audio System requires 230V to operate. There are two power leads coming from the IntelliSound audio system. Typically, these power leads will be red or black in color. The power wires for the IntelliSound Audio System should be passed through the opening shown in illustration A (above). One lead should me connected to an available spade receptacle in positions one through six (see illustration below), the second lead should be connected to an available spade receptacle in positions 7 through twelve (positions 5 and 11 are recommended). To avoid operational issues with the tanning system and the IntelliSound system, assure that the connections are secure and the spade connectors are properly positioned over the spade receptacle (see FIGURE B & C). FIGURE C
Parameters: The CCS and T-Max network control systems may be used to set available user definable parameters of the IntelliSound system. These control systems need to be the CCS II, T-Max Manager or newer controllers. Older systems are not compatible. Below is a table of parameters for use with the IntelliSound Audio System: Intellitan® / T-MAX® INTELLITAN® / T-MAX® VALUES Parameter No. Function DEFAULT MIN 7 Salon Stereo 1 0 8 Customer Input (MP3) 1 0 10 **FM1 955 873 11 **FM2 955 873 12 **FM3 955 873 13 **FM4 955 873 14 DMX 4 0 16 Idle Volume 2 0 17 * Idle Source 0 0 * (0 - Salon Stereo, 1 = Customer Input, 2 = FM1, 3 = DMX)
MAX 1 1 1079 1079 1079 1079 8 9 3
** the frequencies for Radio Stations have to be entered without decimal points (i.e. 98.1 should be entered as 981)
Disabling Audio Source(s): To limit the number of options available audio options available to the tanner, set the value of the appropriate parameter to its minimum value.
Unit Software: The software on the tanning system needs to be version 51 or higher. Software versions below 51 do not support the parameters of the IntelliSound System.
Setting Parameters: User Interface: To Change Parameters To enter the System's data bank, monitor operations and verify the vital functions concerning your unit, use the following step-by-step instructions. These instructions are for level 51 and above of the Intellitan Plus timer. Some new parameters now require that the power be cycled off and back on before the parameter or option will take effect. Note: Use the on the TIME function only.
located
Enter Password Clearance
1.
2. 3.
Press (at the same time) then release buttons located on the TIME button; the display will change from 00:00 to 0000. If you cannot get the display to change to 0000, assure that you have disconnected the network cable(s) from the timer. If power to the tanning unit is not cycled on/off after disconnecting the network cable, you must wait for thirty seconds for the timer to award access to the above mentioned buttons.
Press the
button once so that 0000 begins to flash.
Use the button to enter the appropriate password to perform the desired function. Level one password 0010 (ten) must be entered to view parameters, and level two password 0102 (one hundred and two) to edit parameters. After entering the password press the button. The display will stop flashing and 0001 (level one) or 0002 (level two) will appear in the display.
4. 5.
Press the button once to enter parameter mode and then the TIME the desired parameter. If you are using the second level password, press the the
6.
button to edit the parameter (once
button is pressed the display will begin to flash). Use either the
to set the appropriate value for the parameter, then press
Press the button to reach the next parameter. parameter mode.
button to reach
or
button
to exit the parameter.
Press the button
Note: Parameter mode can only be exited when the display is not flashing.
to exit the edit
Room Controller: Security Levels: There are 4 security levels on the CCS IV. When the CALL / MENU button is pressed, the display will prompt you for a security number. Default security You must enter security level 4 to change the Security Level Numbers. See the attached sheet for the factory default security levels. The description of these levels are as follow: Computer Control Level Sessions can be monitored, but not started manually. Parameters such as Lamp Hours, Session Counts, etc. cannot be checked or changed. Level -1 - Employee Level Session operation only. No parameters such as session counts, lamp hours, etc. can be observed or changed. One asterisk will appear in the display *. Level - 2 - Supervisor's Level Parameters values can be observed but not changed, and the tanning units can be controlled. Two asterisks will appear in the display **. Level 3 - Manager's Level Parameters can be observed and changed, and the tanning units can be controlled. Security numbers cannot be changed. Three asterisks will appear in the display ***
Note: The password should be greater than 128 for each of the three security levels. CCS IV Displays The CCS IV has a 32 characters display (two rows which can display sixteen characters each), which is the users interface to the tanning network. The display along with the key-pad allow the operator to perform all of the Intellitan network functions. Examples:
A.
Bed# 1 00:00 N/A
Tanning unit 1 is not available for address one.
B.
Bed# 1 00:00 READY
Tanning unit has been identified by the CCS IV.
C.
SECURITY #
D.
Bed# 1 00:00 *** READY
Tanning unit is ready for use.
E.
Bed# 1 XX:XX *** DELAY
Prep or session delay counting down xx:xx is the time counting down. The tanning unit will automatically start when the timer reaches zero.
F.
Bed# 1 XX:XX *** ON
Tanning unit 1 is running. The customer tanning has XX:XX time remaining on the session.
G.
Bed# 1 XX:XX *** PAUSE
The tanning session has been paused by the tanner. The xx:xx represent the time remaining on the timer.
H.
. Bed# 2 XX:XX *** COOL
Display which appears when the CALL/MENU button is pressed. You are required to enter a password to operate a tanning unit. (Note: the asterisks displayed represent the security level).
The tanning session on tanning unit one has expired and the fan delay post session cooling is on. The xx:xx represent the time remaining on the fan delay.
I.
Bed# 2 00:00 *** DIRTY
The clean room feature of the Intellitan timer is enabled and the status of the bed is being displayed after the session time has elapsed.
J.
GET PARAMS?
(GET PARAMETERS) First of three Menu’. Can only be accessed with security level two or higher. Allows the user to view the various parameters of the Intellitan timer. Press ENTER to observe the value of a parameter, or CLEAR to return to the bed status display. If you entered this menu using security level three password, you can press the NEXT button to access the other available menus.
WHICH PARAMETER?
First display of the GET PARAMETER menu. Enter the number of the parameter to be viewed and press the ENTER button.
Bed# 002 P#15 Data = BUSY Bed# 002 P#15 Data = 00001
CCS IV is getting the value of parameter fifteen (P15) for bed number two. The value of parameter fifteen (P15) for for bed number two is one(1). To view the value of P15 for other beds you can press the NEXT and PREV (previous) buttons accordingly or press CLEAR to return to the bed status display.
K.
(SEND PARAMETERS) Second of three menus. Can only be accessed with security level three. Allows the user to edit user accessible parameters. Press ENTER to change the value of a parameter, NEXT to access MGR PARAMS? menu or press CLEAR to return to the bed status display.
SEND PARAMS?
WHICH PARAMETER? Bed#: 002
You can press the NEXT or PREV (previous) button to position to another unit if desired or type the number of the parameter to be changed and press the ENTER button.
SEND WHAT DATA?
Type the new value for the parameter and press ENTER or press the CLEAR button to return to the bed status display.
SEND PARAMS?
The CCS IV returns to SEND PARAMS? after updating a parameter. You can press ENTER to edit another parameter or press CLEAR to return to the bed status display.
L.
MGR PARAMS?
(MANAGER PARAMETERS) Can only be accessed with level three security. Allows the user to edit CCS IV parameters. The maximum bed value, manager number, manager re-scan time, and maximum slave values can be entered through this menu.
M.
MGR MAX BED
Press the key(s) for the value of the highest station address on the tanning network and press ENTER. You can press NEXT to proceed to another menu or CLEAR to return to the bed status display.
N.
MANAGER NUM
Applicable only when more than one CCS IV is being used. The valid values are from zero(0) thru seven(7). Each CCS IV on the network has to have a unique manager number. Press the appropriate numeric key to assign the manager number and press ENTER, NEXT or PREV to move to another menu or press CLEAR to return to the bed status display.
O.
MGR RE-SCAN TIME
A value from zero(0) to one hundred(100) minutes may be entered. The CCS IV will scan the entire tanning network at the interval specified here. Key the desired RE-SCAN time and press ENTER.
P.
MAX SLAVE
The value entered here references the number of CCS IVs that have been configured as slaves. Press the appropriate numeric key for the number of CCS IVs designated as slaves, then press ENTER. Press PREV to move to another menu or CLEAR to return to the bed status display.
Compulsory Registration / Liability to Charge (Sound Reproduction): Salon owner is responsible for reporting and paying all fees associated with music being played in the salon.
Warranty: JK Products, Inc. warrants this product to be free from defects in materials and workmanship under intended normal use as described in the unit operation for a period of one year from the date of purchase. The limited warranty applies only to the original purchaser of this equipment through JK Products, Inc. or its authorized dealer or distributor and is not transferable.
