Transcript
1
Minimum Hardware Requirements
Intel®
Server System R1304BTSSFAN Quick Start User's Guide
To avoid integration difficulties and possible damage to your system, make sure you have components from each category below. ■ Heat Sink: • 1U passive heat sink. ■ Memory: • Memory Type: Minimum of one 1 GB, 240-pin DDR3 1066/1333 MHz ECC UDIMM. ■ Hard Disk Drives: • SATA ■ Power: • Minimum of 250W with 2A of standby current, which meets the SSI EPS 12V specification.
Thank you for buying an Intel® Server System. The following information will help you assemble your Intel® Server System R1304BTSSFAN and install components.
Tools Required
Phillips* screwdriver
3
Read all cautions and warnings first before starting your server system integration.
Remove Top Cover A B
Observe normal ESD (Electrostatic Discharge) procedures.
Remove the four security screws. Slide cover back and lift upward.
B
Place your Intel® Server Chassis on a flat anti-static surface to perform the following integration procedures. Always touch the chassis frame first, before reaching inside to make server board connections or to install components.
Fastener Identification Guide
This guide and other supporting documents are located on the web at http://www.intel.com/support/motherboards/server If you are not familiar with ESD (Electrostatic Discharge) procedures used during system integration, please see the Intel® Server System R1304BTSSFAN Service Guide, available on the Intel® Server Deployment Toolkit CD or at http://www.intel.com/support/motherboards/server
2
Preparing the Chassis
A B
Anti-static wrist strap
Remove Air Duct
Removing air duct by lifting straight up.
4
Remove Add-in Card Riser Assembly
IMPORTANT! Before proceeding further, do the following:
Grasp riser with both hands and pull straight up to release riser card connector from server board socket. Riser Card Connector
Check your Intel® Server System for disconnected or loose cables and components that may have occurred during shipping.
CAUTION: Place the riser assembly upsidedown to avoid damage to the riser card connector.
Warning Read all caution and safety statements in this document before performing any of the instructions. Also see the Intel® Server Board and Server Chassis Safety Information document at: http://www.intel.com/support/ motherboards/server/sb/cs-010770 .htm for complete safety information.
5
Install the Processor
A. Open the Socket Lever A
Cautions:
Push the lever handle down and away from the socket to release it.
When unpacking a processor, hold by the edges only to avoid touching the gold contact wires.
A
Warning
B. Open the Load Plate Open the load plate as shown.
Carefully lower the load plate over the processor.
CAUTION: The underside of the processor has components that may damage the socket wires if installed improperly. Components
A
Orient the processor with the socket so that the processor cutouts match the two socket pins.
B
Note location of gold key at corner of processor.
C. Unpack the Processor
Rotate the lever open all the way.
Carefully remove protective cover as shown. Save the protective cover.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright © 2011, Intel Corporation. All rights reserved.
6
Install Heat Sink A
Get heat sink from the shipping position.
B
Remove the protective film on the TIM if present.
C
Align heat sink fins to the front and back of the chassis for correct airflow. Airflow goes from front-to-back of chassis.
The heat sink has four captive fasteners and should be tightened using the following procedure:
D
Using a #2 Phillips* screwdriver, finger-tighten each fastener diagonally, according to the numbers shown.
E
Securely re-tighten each fastener again in the same order as performed in Step E.
A
B
A
7 D E
Install DIMM Memory Modules
B
Close the load plate locking lever.
A
W FLO
AIR
B
Slide the tip of the lever under the notch in the load plate. Make sure the lever is securely latched.
This server board supports up to 4 DDR3 1066/1333 ECC UDIMM.
1
2
Shoulder Screw
Memory Configurations and Population Order:
B
B
To Install DIMMs: CAUTION: Avoid touching contacts when handling or installing DIMMs.
DIMM A2 DIMM A1 DIMM B2 DIMM B1
4
TIM
Save the protective cover.
A
CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures to avoid possible damage to system components.
3
Carefully lift the cover straight up as shown.
Push down on the locking lever. CAUTION: DO NOT damage the server board with the tip of the locking lever.
B
DDR3 DIMM Memory Identification:
C
as
CAUTION: The heat sink has thermal interface material (TIM) on the underside of it. Use caution so that you do not damage the thermal interface material. Use gloves to avoid sharp edges.
CAUTION: Do not over-tighten fasteners.
Ch
G20493-003
Make sure the front edge of the load plate slides under the shoulder screw as the lever is lowered.
Load Plate Front Edge
Pr o So ces ck so et r
Low Power Unit, Please Check Power Budget Tool For Supported Configuration.
A
H. Remove the Cover
A
Caution
Caution
G. Latch the Locking Lever
DO NOT DROP processor into socket!
Installation and service of this product should only be performed by qualified service personnel to avoid risk of injury from electrical shock or energy hazard.
Observe normal ESD [Electrostatic Discharge] procedures during system integration to avoid possible damage to server board and/or other components.
F. Engage the Load Plate
Processor must align correctly with the socket opening before installation. DO NOT DROP processor into socket!
1
B
E. Close the Load Plate
D. Install the Processor
DIMM notch and socket bump must align as shown.
A B C D E
Open both DIMM socket levers. Note location of alignment notch. Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot. Push down firmly on the DIMM until it snaps into place and both levers close. IMPORTANT! Visually check that each latch is fully closed and correctly engaged with each DIMM edge slot.
Memory Type: Minimum of one 1 GB, DDR3 1066/1333 MHz ECC UDIMM. Note: For additional memory configurations, see the Intel® Server Board S1200BT Techinical Product Specification at: http://www.intel.com/support/motherboards/server
sis
DDR3
t
on
Fr
Other Memory
Memory sizing and configuration is supported only for qualified DIMMs approved by Intel®. For a list of supported memory, see the tested memory list at http://serverconfigurator.intel.com/default.aspx
C
E
D A
B
