International Point Of Sale: Cornerstore Pos

Transcript

International Point of Sale: CornerStore POS POSX TP4 All-In-One Guide The POS-X TP4 All-In-One comes with everything you would need, and EVO Printer, Evo Cash Drawer, TP4 Rear Display and a Mag Swipe. 1 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Installing the PoSX Customer Display The PoSX Pole Display has 2 different Variations. - A Rear Customer Display A Customer Pole Display. Rear Display 2 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS How to attach the VFD Rear Display Step 1: First you must disassemble the computer from the stand (if you have not done so already) Step 1a: Loosen the Thumb Screw [1] and slide the stand towards the panel on the bottom. To attach the stand back, reverse the steps mentioned. 3 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 2: Attach the VFD to the stand by fastening the screws [2], as shown below Step 3: Run the cable through the slot shown above. Step 4: Connect the cable onto the COM 4 slot (Mark with 12V in red color) on the panel under the monitor. Step 5: Put the Monitor back onto the stand. 4 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Installing the Drivers for the VFD Step 1: Download the file: http://cornerstorepos.com/downloads/hardware/EVO-RD4-VFD%20Config.zip Step 2: Open the application P07303II_AIO Step 3: Click on Scan Device. 5 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 4: Make sure the device is plugged into the computer before proceeding. Click on Auto-Scan. It should produce a message at the top of the screen when done looking similar to this. Take note of the COM number. 6 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 5: Click on Change Settings. Step 6: Change Baud Rate to 9600, Data Bits to 8 and Command Type to 7=CD5220. Click Set to Device. 7 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 6: Open up Corner Store and go to Setup -> Hardware Setup -> Pole Display. Step 7: Select General and select the COM port that was noted earlier. Click Save & Exit. You have now set up the POSX Rear Display with CornerStore. 8 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Magnetic Swipe Reader (MSR) – The MSR is a “plug-and-play” hardware, you do not need any drivers. How to attach the MSR onto the monitor Step 1: Remove the screws [2] from the Dummy Cover on either side (your choice) Step 2: Connect the cable from the MSR into the connected on the side (as shown below) Step 3: Insert the reader in place and fasten the screws [2] to keep it secure (as shown above) 9 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Installing the PoSX Printer First install the drivers from the website: http://cornerstorepos.com/downloads/hardware/POSX_EVO_RP1_OPOSDriver.exe 10 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 1: Open the file, click Run. Step 2: Click Next >. 11 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step3: Click Next >. Step 4: Click Next>. 12 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 5: Click Finish. Step 6: Go to My Computer then click on C: drive -> Program Files -> OPOS -> StdOPOS2.8t then open up SetupPOS. 13 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 7: Click on POSPrinter, then click Add New Device. Step 8: For Device Name select Thermal, For Device Type select Thermal U, Click OK. Step 9: Select Add New LDN and enter in a name for your printer. Click OK. 14 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 10: Click on Cash Drawer then click Add New Device. For Device name select Standard, For Device Type select StandardU. Click OK. Step 11: Click on the Cash Drawer and select Add New LDN, enter in a name for the cash drawer and click OK.. Step 12: Click on the Thermal Printer, then click Device Details. Click Printer Test And Setting. 15 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 13: Click Printer Test, a test page should come out of the printer. Click Close, then OK. Step 14: Click on the Cash Drawer and click Device Details. Then click on Printer Test And Setting. 16 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 15: Put Open Level to High, and Pin No to 5 only if you are using a POSX cash drawer. If you are using any other cash drawer do nothing. Click on Printer test, the cash drawer should open. Click close then OK. 17 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 15: Open up CornerStore and go to Setup -> Hardware Maintenance. On the Printers tab, select the ThermalU. Go to the Cash Drawers Tab. \ 18 1-866-468-5767 or 201-928-0222 International Point of Sale International Point of Sale: CornerStore POS Step 16: Select the StandardU. Press Save& Exit. 19 1-866-468-5767 or 201-928-0222 International Point of Sale