Transcript
EX29351
MODULAR JACK REQUIREMENTS You need an RJ11 type modular phone jack, which is the most common type of phone jack. If you don’t have a modular jack, call your local phone company to find out how to get one installed.
Telephone User s Guide
INSTALLING THE PHONE DESKTOP INSTALLATION 2
1
1. Telephone Memory Label 2. M1,M2,M3 button, one touch memory dialing buttons. 3. In use indicator 4. Message indicator 5. Store button 6. Dial button 7. Mute button 8. Pause button 9. Redial button 10. Speakerphone button 11. Flash button 13. P/T Switch 14. Flash Switch 15. Ring Volume Switch
SET UP 1. Plug the coiled cord into the corded handset and the base. 2. Plug the telephone line cord into the modular jack and into the TEL. LINE jack on the back of the base. 3.Lift up the handset and then put down the handset on the cradle. NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse (rotary) dialing, see "Tone/Pulse Dialing". If you don't know which type of service you have, check with the phone company.
FUNCTION KEY AND SWITCH
INTRODUCTION
FLASH TIME SETTING
5
2
6
3
7
4
8
1
2
BEFORE YOU BEGIN
M2
3 4
M3
2
ABC
3
DEF
5
JKL
6
MNO
GHI
4
8
6 MUTE
7
PQRS
8
TUV
9
*
TONE
0
OPER
#
7
WXYZ
There are total 3 speaker volume levels. (HI/MID/LO) you can adjust the volume of the speaker by using the Speaker Volume Control at the side of the base unit.
PAUSE
8
(Default at HI)
REDIAL
FLASH
7
5 DAIL
4
Make sure your package includes the items:
6
SPEAKER VOLUME CONTROL
STORE
1
PARTS CHECKLIST 3
There are total 3 ring levels. (HI/MID/LO) Move ring volume switch in the back of the base to set Ringer level.(Default at HI)
IN USE
MESSAGE
2
NOTE: The phone is shipped in Tone Dialing Mode from the manufacturer.
RINGER LEVEL SETTING 1
M1
5
Move T/P switch in the bottom to set dialing mode. (T: tone or P: pulse.) Under pulse dialing mode, press “*” button to get tone dialing mode temporarily.
Move FLASH switch in the bottom to set FLASH timing. (100ms/300ms/600ms.)(Default at 600ms)
Your Telephone is designed to give you flexibility in use, and high quality performance, To get the most from you new telephone, we suggest that you take a few minutes right now to read through this instruction manual. If you have any questions or problems, consult the Troubleshooting Guide for the solution.
1
TONE/PULSE DIALING SELECTION
PHONE BASICS
SPEAKER
IN U S E
M1
M2
M3 M ES SAG E S TO R E
1
2
ABC
3
DEF
D AIL
4
GHI
5
JKL
7
PQRS
8
TUV
*
TONE
0
OPER
6
MNO
9
WXYZ
11
M UTE
10
9
IN USE INDICATOR
PAUS E
#
The “IN USE” indicator will light up when the phone is on the line.
REDIA L
F L ASH
SP EAK ER
Base
Corded Handset
SPEAKER INDICATOR The SPEAKER indicator will light up when the speaker is activated. P T
Telephone Line Cord
Handset Coiled Cord
12
100 300 600 FLASH
13
LO MID HI RINGER
14
TEL.LINE
15
RECEIVING A CALL 1. Press the “SPEAKER” button or pick up the handset to answer the phone. 2. Press the “SPEAKER” button again or put the handset on cradle to hang up.
MAKING A CALL To make a call, press the “SPEAKER” button or pick up the handset before you dial and press “SPEAKER” button again or put the handset on cradle to hang up.
REDIAL To repeat a call to the last number you dialled(up to 32 digit) 1. Press "SPEAKER" button or pick up the handset to get a dialling tone. 2. Press "REDIAL" button to dial the last number redial.
PAUSE Press the “PAUSE” button when you dial the telephone number, duing the phone dialing the phone shall pause for 2-4 second.
Warning: If the phone is disconnected from the telephone line, any stored numbers while be lost within 1.5 hour. If you want to change a number stored in a memory, simply store another one over it. please ignore any tones or recorded messages you may hear from the network will you are storing number.
STORING A NUMBER IN MEMORY DIRECT MEMORIES To store a number in M1-M3. 1. Pick up the handset, press “STORE” button. 2. Use the number keypad to enter the telephone number you want to store (up to 16 digits). 3. Press “STORE” button again. 4. Press a ONE-TOUCH MEMORY button(M1-M3). 5. Put back handset on cradle.
MUTE To prevent the person you are speaking from hearing you while on a call. Press and hold “MUTE” button.
VISUAL MESSAGE WAITING INDICATOR When you connect the phone to an Alcatel PABX, the VMWI will blink if there has a message in the centralized voice mail system. You need to contact your services provider for more details.
MEMORY The phone has three one-touch memories,M1 to M3 and ten two-touch memories, 0 to 9.Each memory location can have up to 16 digits. You can store part of a number (e.g. the dialling code) in memory, then use a combination of memory and manual dialling, in any order,to make a call.
To keep your telephone working and looking good, follow these guidelines: DO NOT expose to direct sunlight or moisture. Avoid dropping and other rough treatment to the phone. Clean with a soft cloth. Never use a strong cleaning agent or abrasive powder because this will damage the finish. Retain the original packaging in case you need to ship the phone at a later date.
TELEPHONE Problem No dial tone
To dial a number stored in M1-M3. 1. Press “SPEAKER” button or pick up the handset. 2. Press a ONE-TOUCH MEMORY button(M1-M3)
FLASH Use the “FLASH” button to activate custom calling services such as call transfer, which are available through your local telephone company. Don’t use “SPEAKER” button to activate custom calling services, or you’ll hang up the phone.
GENERAL PRODUCT CARE
TWO TOUCH MEMORIES To store a number in a Two-touch memory(0-9) 1. Pick up the handset and press the STORE button; 2. Key in the telephone number to be stored. 3. Press the “STORE” button; 4. Using the dialing keypad, press any button between 09 to enter the memory location. 5. Put back handset on cradle. To dial a number stored in Two-touch memory (0-9) 1. Pick up the handset or press “speakerphone” button; 2. Press the “DIAL”button. 3. Key in the memory location number(0-9); 4. The number will be dialed.
CHANGING A STORED NUMBER Use the same procedure to change a stored number as you store a number the you’re just replacing the phone number with a different one. The new number replaces the old number at the memory location.
Dial tone is OK, but can't dial out Does not ring
Solution Check installation: Is the telephone line cord connected to the base unit and the wall jack? Disconnect the base from the wall jack and connect another phone to the same jack. If there is no dial tone in the second phone, the problem might be your wiring or local service. Make sure the tone/pulse setting is correct. Try to set the Ringer to a higher level. You may have too many extension phones on your line. Try unplugging some phones. See solutions for No dial tone.
MEMORY DIALING Did you program the memory location keys correctly? Did you follow proper dialing sequence? Make sure the tone/pulse setting is correct.
Used equipment must be disposed of in compliance with current environmental protection regulations. You should return it to your reseller or dispose of it in an approved recycling centre.
Model: EX29351 00009112(Rev.0 E) 06-10 Printed in China
