Preview only show first 10 pages with watermark. For full document please download

Iomirror E3210_ds

   EMBED


Share

Transcript

Total Solutions for Industrial Device Networking E3210 Ethernet Peer-to-Peer I/O with 8 digital inputs and 8 digital outputs ››Direct input-to-output signal communication over IP ››High speed Peer-to-Peer I/O within 20 ms ››One physical alarm port for connectivity status ››Quick and easy utility and web-based settings ››Local alarm and remote alarm message ››Supports Modbus/TCP for remote monitoring ››Optional LCD module for simple setting Peer-to-Peer I/O Introduction Split sensor signals to sixteen different locations The ioMirror E3000 Ethernet I/O is designed as a cable-replacement solution that connects remote digital input signals to output signals over an IP network. The ioMirror E3210 provides 8 digital input channels, 8 digital output channels, and a 10/100M Ethernet interface. Up to 8 pairs of digital input and output signals can be exchanged over Ethernet with another ioMirror E3210 as well as to a local PLC or DCS controller. Over a local area network, the ioMirror achieves low signal latency, which is typically 20 ms. With ioMirror, remote sensors can now be connected to local controllers or display panels over copper, fiber, or wireless Ethernet infrastructures. Signals can be transmitted over virtually unlimited distances, without noise problems. The ioMirror E3000 can split one input signal to two digital output channels at two different IP addresses. Eight tank level signals can be monitored at sixteen different display panels, all at the same time. ioMirror E3210 Direct input-to-output communication over IP Local alarm with remote alarm messages for monitoring connectivity The ioMirror E3210 has a 24 VDC alarm output channel that can activate an attached buzzer or LED display when the connection fails. In addition, both ioMirror modules can send messages to the ioEventLog software. This ensures that at least one of the warning messages will reach the ioEventLog software. Specifications Digital Input Output Current Rating: Max. 200 mA per channel Channels: 8, source type Optical Isolation: 2K Vrms or 3K VDC I/O Mode: Digital Input Protection: Over-voltage Protection: 45 VDC Over-current Limit: 600 mA (typical) Over-temperature Shutdown: 160°C (min.) Dry Contact: Logic 0: close to GND, Logic 1: open Wet Contact: Logic 0: 0 to 3 VDC, Logic 1: 10 to 30 VDC Isolation: 2K Vrms Common Type: 8 points per COM Digital Output Channels: 8, sink type Alarm Port Output Channels: 1, sink type On-status Voltage: 24 VDC (typical) Output Current Rating: Max. 200 mA per channel Optical Isolation: 2K Vrms or 3K VDC I/O Mode: Digital output On-status Voltage: 24 VDC (typical) email: [email protected] w w w. m o x a . c o m 2-5 Peer-to-Peer I/O I/O Pin Assignment DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI.GND 12 13 14 15 16 17 18 19 20 21 22 23 24 DO.GND DI0 11 DO7 10 DO6 9 DO5 8 DO4 7 DO3 6 DO2 5 DO1 4 DO0 3 DO.PWR 2 Alarm 1 DI.COM I/O (left to right) Wiring Example Digital Input (Wet Contact with NPN Sensor) DO.GND DO7 DO6 DO5 DO4 DO3 DO2 DO1 Alarm Port ALARM + - NPN Sensors 12 to 24 V NPN output 0V 12~24 V Ordering Information • ioMirror E3210: Ethernet Peer-to-Peer I/O with 8 digital inputs and 8 digital outputs • LDP1602: LCD module with 16 x 2 text display and 5 buttons www. m ox a. com em a i l : i n f o @ m o x a . c o m + - Brown Black GND DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI.COM DI0 Pin1 DI.COM Peer-to-Peer I/O ioMirror E3210 + Blue 2-6 DO0 DI.GND DO.PWR Digital Output DI6 DI5 DI4 DI3 DI2 DI0 DI.COM Digital Input (Dry Contact)