Transcript
IMPORTANT MANUAL
Do Not Throw Away
PART'S MANUAL MODEL NUMBER:
PR18530ES
SNOW THROWER
WARNING:
Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury.
Always Wear Eye Protection During Operation Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
585 23 06-27
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) AUGER HOUSING / IMPELLER ASSEMBLY
1
KEY NO. 1 2 3 4
PART NO. 532 44 47-62 532 40 76-45 872 27 05-05 532 15 53-77
DESCRIPTION AUGER HOUSING SCRAPPER BAR CARRIAGE BOLT 5/16−18 X .625 NUT 5/16−18
KEY NO. 1 2
PART NO. 532 42 11-24 532 42 11-25
DESCRIPTION AUGER ASSEMBLY 30 LH AUGER ASSEMBLY 30 RH
3 (5x) 4 (5x) 2
01.07.003-A
2
1
01.07.019-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) AUGER HOUSING / IMPELLER ASSEMBLY 5
11 11
6
7 13
11 12 4
11
3
8
12
14
10
1 34
9 2 9 30 31
9 34
29 27
28 28
17
23
26
33
24 25
20
19
18
22 32
15
18 16
19
20
21 2 (EXPLODED)
01.07.032-A NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 22
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) AUGER HOUSING / IMPELLER ASSEMBLY
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
PART NO. 532 18 41-05 584 64 83-01 532 18 89-09 585 09 32-01 532 44 24-38 532 18 40-95 532 19 21-99 532 40 54-00 873 80 04-00 874 78 04-26 532 42 79-42 532 16 31-83 532 18 03-55 532 19 41-89 532 40 77-60 532 42 73-02 532 42 73-45 532 40 77-70 532 40 77-62 532 17 46-97 580 36 41-01 532 40 77-64 532 18 92-82 532 40 77-58 532 17 46-83 584 64 84-01 532 18 42-05 532 17 46-81 532 17 46-84 532 40 77-69 532 40 77-68 532 40 77-67 532 42 73-17 532 19 20-90
DESCRIPTION IMPELLER GEARBOX ASSEMBLY BEARING IMPELLER PULLEY DISCHARGE BASE CORNER BRACKET CLEAN OUT TOOL TOOL CLIP NUT 1/4-20 SCREW 1/4-20 X .625 NUT 5/16-18 SCREW 5/16-18 X .625 CARRIAGE BOLT SCREW 13-16 X .625 PLUG GEARBOX COVER RH GASKET SEAL BEARING THRUST WASHER 1.00 WORM GEAR AUGER SHAFT SQUARE KEY BEARING THRUST WASHER IMPELLER SHAFT ROLL PIN THRUST WASHER THRUST BEARING BEARING O-RING SCREW 5/16-18 X .750 GEARBOX COVER LH SHEAR BOLT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) AUGER HOUSING / IMPELLER ASSEMBLY
2
3
1
1
2
3
KEY NO. 1 2 3
01.07.024-B
PART NO. 532 42 04-78 532 41 19-39 532 17 95-82
DESCRIPTION AUGER BEARING BEARING PLUG SCREW 5/16−18 X 1.00
2
1 3
3 KEY NO. 1 2
PART NO. 532 43 59-51 532 42 65-89
3
872 11 05-10
DESCRIPTION PLATE SKID PLASTIC HDPE NUT 5/16-18 LARGE HEX FLANGE BLK CARRIAGE BOLT 5/16-18 X 1.25
1 2
01.11.003-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 24
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) CONTROL PANEL / DISCHARGE CHUTE 5
7 15
3 16
*14
*11
2 6
4 KEY NO. 1 2 3 4 5 6 7 8 9 *10 *11 *12 *13 *14 15 16
PART NO. 532 44 42-39 532 43 88-32 585 27 17-01 532 42 03-25 532 41 42-80 532 12 84-15 817 54 10-08 532 43 03-24 532 42 17-28 532 17 98-29 532 19 17-30 872 25 05-05 532 75 11-53 532 18 45-05 532 42 06-79 585 27 16-01
6 DESCRIPTION CHUTE WELDMENT DEFLECTOR WELDMENT 1 DEFLECTOR CONTROL ASSEMBLY DEFLECTOR SEAL KNOB BLACK POP RIVET SCREW 10-24 X .625 6 CHUTE SNOW SHIELD SHIELD RETAINER STRAP SHOULDER BOLT 1/4-20 X .375 01.09.015-D NUT 1/4-20 CARRIAGE BOLT 3/8-16 X .625 NUT 5/16-18 DEFLECTOR SPRING (SERVICE PART) DEFLECTOR CONTROL (SERVICE PART) DEFLECTOR CABLE BLACK
*10
*13 *12
8
9
NOTE: 1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT. 2. ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) CONTROL PANEL / DISCHARGE CHUTE 2 2 1 *3
*7
*6
*4
*5 01.09.010-C
KEY NO. 1 2 *3 *4 *5 *6 *7
PART NO. 532 42 82-72 817 54 10-08 532 42 06-78 532 40 59-32 532 42 06-75 532 42 82-73 532 42 83-10
DESCRIPTION LEVER/CABLE ROTATOR ASSEMBLY SCREW 10-24 X .625 ROTATOR HEAD ROTATOR PIVOT BRACKET PULLEY PIVOT CABLE ASSEMBLY ADJUSTABLE CABLE ASSEMBLY HEAT SHIELD
NOTES: 1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
2
KEY NO. 1 2
1
PART NO. 532 43 86-29 874 04 10-24
DESCRIPTION STEER CABLE SCREW 10−24 X 1.50
01.15.017-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26
REPAIR PARTS HANDLES
SNOW THROWER - MODEL PR18530ES (96198004905)
3
3 4
4 4 5 3
1
3
4
KEY NO. 1 2 3 4 5
PART NO. 532 42 11-20 532 42 11-21 874 78 05-24 532 75 11-53 532 05 56-11
KEY NO.
PART NO.
DESCRIPTION
1 2 3 4 5
585 23 81-02 532 44 36-17 817 00 05-10 817 00 06-16 817 00 06-12
LOWER HANDLE PIVOT SUPPORT WELDMENT SCREW 5/16−18 X .750 SCREW 3/8−16 X 1.00 SCREW 3/8-16 X .750
DESCRIPTION LOOP HANDLE LH LOOP HANDLE RH SCREW 5/16−18 X 1.50 NUT 5/16−18 WASHER FLAT
2
01.08.004-C
1
2 4 3 5 4 5 3
01.05.013-E
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27
REPAIR PARTS HANDLES
SNOW THROWER - MODEL PR18530ES (96198004905)
2
KEY NO. 1 2 3 4 5 6 7 8 9 10
3
1
8 9 4
PART NO. 584 80 87-01 584 80 88-01 532 18 04-45 532 18 77-16 532 18 04-47 580 79 62-01 580 80 21-01 872 27 05-05 532 15 53-77 532 16 96-75
DESCRIPTION ROD IMPELLER CONTROL ROD TRACTION CONTROL SHIFTER ROD TOP SHIFTER ROD BOTTOM SPRING SLEEVE SPRING CONTROL ROD SPRING TRACTION ROD CARRIAGE BOLT 5/16-18 X .75 NUT 5/16-18 RETAINER HAIRPIN
NOTE: HOOK TRACTION ROD SPRING IN HOLE 7 HOOK IMPELLER ROD SPRING IN HOLE 4
5
7
10 5
6 01.12.013-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28
REPAIR PARTS HANDLES
SNOW THROWER - MODEL PR18530ES (96198004905)
2
10
9
8
7
5 6
4
11 12 1
3 14 11 12
11
11 12
13
12
13
13 13
01.08.021-A
KEY NO.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14
585 19 88-02 581 77 98-01 581 77 97-01 584 80 90-01 585 00 47-03 874 78 04-10 532 42 16-13 532 08 83-49 532 41 42-81 532 41 42-80 532 17 88-99 819 13 13-16 872 12 06-18 532 16 96-75
CONTROL PANEL LH CONTROL LEVER RH CONTROL LEVER INTERLOCK CONTROL ROD INTERLOCK BRACKET 1/4-20 X .625 HEX HEAD SCREW SPACER 1/4-20 FLANGE NUT (TOP LOCK) KNOB RED KNOB BLACK HANDLE KNOB 3/8 WASHER CARRIAGE BOLT 3/8-16 X 2.25 RETAINER
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29
REPAIR PARTS HANDLES
SNOW THROWER - MODEL PR18530ES (96198004905)
4
3 2
5
1
PART NO. 532 41 62-88 532 44 52-91 532 44 32-15 532 16 96-75 817 06 04-10 532 42 18-14
KEY NO. 1 2 3 4
PART NO. 532 18 29-06 532 17 86-68 532 18 09-27 532 18 44-71
5 6 7
532 17 52-62 532 44 50-29 532 18 37-84
DESCRIPTION INTERLOCK SPRING INTERLOCK CAM TORSION SPRING RETAINER SCREW 1/4−20 X .625 INTERLOCK STOP
01.08.007-D
6
7
4 5
3 2
6
KEY NO. 1 2 3 4 5 6
4
5
1
DESCRIPTION CONSOLE PANEL HEADLIGHT BEZEL FLOOD HEADLIGHT SHOULDER SCREW 10−24 X .625 SCREW 10−24 X 1.25 WIRE HARNESS BULB
01.10.007-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 30
REPAIR PARTS DRIVE
SNOW THROWER - MODEL PR18530ES (96198004905)
6 9
7
8 9 1b
7
1b
4 3
1a
2 3
5 6
4
01.03.002-C
KEY NO. 1 1a 1b 2 3 4 5 6 7 8 9
PART NO. 532 40 49-23 532 40 43-07 532 18 42-06 532 40 26-91 532 44 49-49 532 17 98-30 532 14 63-15 817 49 05-08 532 17 12-71 532 18 92-82 532 12 47-88
DESCRIPTION AXLE ASSEMBLY (ASSY OF 1A,1B) AXLE SHAFT ROLL PIN 3/16 X 1.50 SPROCKET THRUST WASHER BEARING SCREW 5/16−18 X .625 SCREW 5/16−18 X .500 CLEVIS PIN 1/4 X 1−3/4 SQUARE KEY RETAINER
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31
REPAIR PARTS DRIVE
SNOW THROWER - MODEL PR18530ES (96198004905)
2
ITEM 42 EXPLODED 1
11 9 10
9 45
8
6
16
12 9 11 45 13 11
15 14 15
20
22
24
45
4 23
34 21
5
26
33
23
27
26
28
29
30
31 32
24
33
38 35 45 36
4 23
18
19
7
45 3
24
17
37 25 24
46
42 43
39
44
41 40 39
01.02.013-H
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 32
REPAIR PARTS DRIVE KEY NO. 1
PART NO. 532 19 88-75
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
817 54 10-08 532 43 88-37 817 49 05-08 532 05 70-79 532 40 54-85 532 19 85-80 532 41 54-50 532 40 28-81 532 41 54-33 532 19 17-30 532 41 54-35 532 41 68-64 532 18 71-01 532 70 02-79 532 42 75-42 532 40 25-68 532 16 96-75 532 41 54-29 532 40 23-10 812 00 00-36 532 40 28-78 532 75 11-53
SNOW THROWER - MODEL PR18530ES (96198004905)
DESCRIPTION SPEED SELECTOR ASSEMBLY SCREW 10-24 X .625 END PLATE SCREW 5/16-18 X .50 WASHER CONTROL ARM CLEVIS PIN SHIFTER PLATE SHOULDER BOLT SHIFTER BRACKET NUT 1/4-20 CLUTCH PLATE CLUTCH BRACKET SHIFTER LINK RETAINER CONTROL SHAFT CLUTCH ROD RETAINER SHIFTER YOKE PIVOT ROD RETAINER RETURN SPRING NUT 5/16-18
KEY NO. 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
PART NO. 532 40 89-81 873 93 05-00 532 19 95-09 585 02 10-01 532 17 53-44 532 17 86-13 874 76 05-14 812 00 00-12 532 40 21-87 532 40 16-19 532 43 73-03 581 42 25-01 532 18 01-35 532 40 26-52 532 42 82-88 532 18 44-71 532 41 08-77 532 41 66-82 585 11 12-01 532 41 45-57 532 17 88-28 532 42 88-67 817 00 05-10
DESCRIPTION BEARING NUT 5/16-18 RUBBER WHEEL PLATE RUBBER RING BEARING WHEEL HUB SCREW 5/16-18-.875 RETAINER RING SPROCKET SHAFT CHAIN SPROCKET WELDMENT SHIFTER BRACKET SPRING PLATE PIVOT ROD E-RING .375 SHOULDER SCREW BOTTOM PAN SPRING BRACKET DRIVE PLATE ASSEMBLY IDLER SPRING IDLER SPRING SCREW 5/16-18 X .750 SCREW
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 33
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) CHASSIS / ENGINE / PULLEYS 2 3
2
3
1
01.00.034-A
KEY NO.
PART NO.
--
580 42 67-01
1 2 3
532 43 88-40 532 15 04-06 532 42 88-67
LCT COMPLETE ENGINE PW2HK1911507-81D FRAME BOLT 3/8-16 SCREW 5/16-18 X .750
KEY NO. 1
PART NO. 532 43 88-42
DESCRIPTION ENGINE MOUNTING PLATE
KEY NO. 1
PART NO. 532 42 86-85
DESCRIPTION COVER ASSEMBLY
DESCRIPTION
1
01.01.004-A
1
01.21.014-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 34
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) CHASSIS / ENGINE / PULLEYS 23 19
13 21
11
20
18
20 18 17 16 22
15 14 12
7 9
5
10
4
3
6 2
1
8
01.21.020-J
KEY NO. 1 2 3 4 5 6 7 8 9 10 11
PART NO. 532 43 07-84 532 42 73-04 584 23 24-02 532 18 05-23 585 28 49-01 532 42 65-89 874 78 05-24 532 42 42-97 532 75 11-53 817 00 05-10 585 23 84-01
DESCRIPTION IMPELLER BELT TRACTION BELT IDLER ARM BRACKET IDLER PULLEY IDLER BRACKET NUT 5/16-18 SCREW 5/16-18 X 1.50 SHOULDER BOLT 5/16-18 X .50 NUT 5/16-18 LOCK SCREW 5/16-18 HEX TRACTION IDLER BRACKET ASM
KEY NO. 12 13 14 15 16 17 18 19 20 21 22 23
PART NO. 532 85 10-84 532 05 92-89 819 13 20-05 585 20 02-01 585 02 93-01 874 61 05-16 810 04 05-00 585 54 05-01 532 15 54-15 532 17 53-31 874 61 05-20 874 76 06-08
DESCRIPTION SCREW 3/8-24 X 1.375 WASHER WASHER PULLEY ENG IMPELLER PULLEY ENG TRACTION SCREW 5/16-24 X 1.00 LOCKWASHER 5/16 BELT GUIDE WASHER 5/16 IDLER BUSHING SCREW 5/16-24 X 1.25 SCREW 3/8-16 X .500
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 35
REPAIR PARTS WHEELS
SNOW THROWER - MODEL PR18530ES (96198004905) 2
2
18
17 16 20 19
15 24
16
11
23 22
21
21
7
2 3 1 2
4
8
9
10 11
23
17 19 22
20
12
13 14
13
14
9 8 10
7
6
5
4
3
1
12
5 6
01.15.021-B
KEY NO.
PART NO.
DESCRIPTION
KEY NO.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12
532 40 51-61 532 18 44-71 812 00 00-45 581 64 50-01 532 18 24-66 532 18 76-22 581 64 49-01 532 17 91-39 532 18 92-82 581 64 51-01 532 44 49-49 532 44 52-66
COVER SHOULDER SCREW RETAINER SPRING WHEEL DRIVER RETAINING RING WHEEL LOBE CLUTCH SLIDE SPRING SQUARE KEY AXLE LOBE THRUST WASHER STEERING YOKE
13 14 15 16 17 18 19 20 21 22 23 24
532 18 41-97 817 49 05-08 532 19 95-11 532 19 95-18 532 18 18-47 817 60 04-06 532 40 50-77 532 70 02-79 532 08 51-79 532 19 38-85 532 18 20-15 532 19 95-12
STEERING BRACKET SCREW 5/16-18 X .50 PIVOT BRACKET BELLCRANK BELLCRANK PIN SCREW 1/4-20 X .375 STEERING LINK RETAINER RETAINER SPRING LEVER PIN PIVOT BRACKET
KEY NO. 1 2 3 4 5
PART NO. 532 43 84-46 532 43 84-47 817 49 04-08 817 60 04-06 819 13 13-12
DESCRIPTION CABLE BRACKET LH CABLE BRACKET RH SCREW 1/4 -20 X .500 SCREW 1/4 -20 X .375 WASHER 13/32 X 13/16 X 12 GA
5
4 2
1
3
01.15.015-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 36
REPAIR PARTS WHEELS
SNOW THROWER - MODEL PR18530ES (96198004905)
KEY NO. 1 2
1
2
PART NO. 532 44 47-60 532 44 47-61
DESCRIPTION WHEEL ASSEMBLY LH WHEEL ASSEMBLY RH
01.06.014-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 37
REPAIR PARTS BAG OF PARTS
SNOW THROWER - MODEL PR18530ES (96198004905)
4 6
5
8
7 3
9
10
2 12
1
11
01.14.003-B
1
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12
PART NO. 532 19 85-63 532 16 96-75 532 42 91-12 532 18 45-05 532 17 98-29 532 19 17-30 872 25 05-05 532 75 11-53 873 80 06-00 819 13 13-16 532 19 20-90 873 80 04-00
DESCRIPTION POWER CORD RETAINER PIN WRENCH REMOTE SPRING SHOULDER BOLT 1/4-20 LOCKNUT 1/4-20 CARRIAGE BOLT 5/16-18 X 5/8 LOCKNUT 5/16-18 LOCKNUT 3/8-16 WASHER 3/8 SHEAR BOLT 1/4-20 X 1-13/16 LOCKNUT 1/4-20
KEY NO. 1
PART NO. 532 44 30-59
DESCRIPTION SAFETY IGNITION KEY KIT
01.14.009-B
1
3
2
4
1
4 2 01.14.012-B
KEY NO. 1 2 3 4
PART NO. 532 18 04-45 532 18 77-16 872 27 05-05 532 15 53-77
DESCRIPTION SHIFTER ROD TOP SHIFTER ROD BOTTOM CARRIAGE BOLT 5/16-18 X .75 NUT 5/16-18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38
REPAIR PARTS DECALS
SNOW THROWER - MODEL PR18530ES (96198004905)
1 4
5 2 6
3 1
KEY NO. 1 2 3 4 5
PART NO. 532 18 10-37 532 18 10-33 532 18 10-35 532 18 10-42 581 43 01-01
6
581 43 01-02
---
585 23 06-27 585 23 08-31
DESCRIPTION DECAL, DANGER DECAL, CONSOLE INSTRUCTION E/F DECAL, DANGER, DEFLECTOR DECAL, DANGER DECAL, CONSOLE RT SPEED LEVER POWERSTEERING DECAL, CONSOLE LT DEFLECTOR LEVER POWERSTEERING OWNER’S MANUAL, ENGLISH OWNER’S MANUAL, FRENCH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 39
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) COMPLETE ENGINE-580426701
16 36
14
27
58
26
47 23 31
37
35
10
34
40
18
7
32
22
33 *
8
25
64 5
38*
19 15
27
1
20
61 60
22
60
*Included with part #1
24 43 65
49 39
42
3
4
55
51
59
57
2
9
17
77
21 53
54
62
48
56 50 52
29
13 Carburetor Repair Kit
30
70
28 ILLUSTRATION FOR REFERENCE PURPOSES ONLY
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 40
REPAIR PARTS SNOW THROWER - MODEL PR18530ES (96198004905) COMPLETE ENGINE-580426701
KEY PART NO. NO.
DESCRIPTION
1
532 42 96-05
2
532 42 96-06
3 4 5 7 8
532 42 93-03 532 42 96-07 532 42 93-15 532 42 93-13 532 44 39-00
9 10
532 42 93-06 532 44 66-44
13 14 15 16
532 42 92-08 532 42 92-09 532 42 92-34 532 42 92-11
17 18
532 42 92-95 532 44 39-44
20 21 22
532 42 92-55 532 42 92-23 532 42 92-32
23 24 25 26
532 43 21-46 532 42 92-86 532 42 93-12 532 42 93-10
27
532 42 93-11
28 29 30
532 42 92-99 532 42 93-00 532 42 93-02
31
580 98 41-01
32
532 42 93-16
HEAD ASSY KIT (45 DEGREE NON-GENERATOR) PUSH ROD KIT (414CC)(INCL. VALVE COVER GSKT) VALVE COVER CYLINDER ASSEMBLY-SNOW PISTON & ROD ASSEMBLY CAMSHAFT SYSTEM ASSEMBLY FLYWHEEL(ELECTRIC START) (60-WATT) 414CC COOLING FAN- FLYWHEEL CRANKSHAFT (#19 SNOW) (414CC) MUFFLER ASSEMBLY-SNOW FUEL TANK ASSEMBLY-SNOW FUEL PETCOCK-SNOW FUEL TANK CAP(OVERSIZED) CLICK STYLE-SNOW CARBURETOR ASSEMBLY-SNOW IGNITION COIL (CDI) (291-414CC) (STD) SPARK PLUG ON/OFF SWITCH-SNOW SHIELD-UNDER FLYWHEEL CHARGING SYSTEM-SNOW FUEL HOSE KIT TOP SHIELD GOVERNOR GEAR ASSEMBLY GOVERNOR ARM ASSY (414CC) (INCL. LINK & SPRINGS) GOVERNOR ARM SHAFT ASSEMBLY RECOIL STARTER ASSY-SNOW STARTER CUP SMALL-SNOW BLOWER HSG ASSY-ELECTRIC START-SNOW CRANKCASE COVER ASSEMBLY (HIGH OIL FILL) OIL SEAL KIT (414CC)
KEY PART NO. NO. 33
532 42 92-90
34 35 36 37 38 39 40 42 43 47 48 49 50 51 52
532 43 69-66 532 42 92-97 532 42 96-09 532 43 55-34 532 42 96-12 532 42 92-24 532 42 92-42 532 42 92-57 580 35 38-01 532 42 92-37 532 42 92-84 532 43 54-94 532 42 92-94 532 42 92-31 532 42 92-18
53 54 55 56 57
532 42 92-21 532 44 30-59 532 43 26-87 532 42 92-13 532 43 74-66
58
532 42 92-98
59 60
532 42 93-18 532 44 38-96
61 62
532 43 27-52 532 42 93-01
64 65 70
532 42 96-08 581 37 29-01 580 35 36-01
77
532 43 26-88
DESCRIPTION ELECTRIC STARTER BRACKETSNOW SPARK PLUG BOOT-SNOW ELECTRIC STARTER ASSY-SNOW ENGINE GASKET KIT BLACK OIL DIPSTICK ROCKER ARM KIT CHOKE KNOB-SNOW NON-REMOVABLE OIL PLUG CDI BOX BRACKET-SNOW BREATHER TUBE (291/414CC) HIGH OIL FILL ASSY KIT-SNOW WIRE HARNESS-SNOW OIL DRAIN PLUG KIT HEATER BOX ASSEMBLY-SNOW SHIELD- CYLINDER PRIMER BULB ASSY WITH HOSE-SNOW KEY SWITCH ASSEMBLY-SNOW KEY SET (RED) SNOW OIL DRAIN TUBE-SNOW 291/414CC VAPOR SHIELD-SNOW CE COMPLIANT MUFFLER SHIELD GOVERNOR LINKAGE SHIELD PLATE-SNOW FUEL TANK SKIRT-SNOW 60 WATT ALTERNATOR (291-414CC) FUEL KNOB-SNOW STARTER GRIP-SNOW-LQA (WILL GO TO SKSN0603.1) COUNTER WEIGHT KIT TAPPET KIT (291/414CC)(SET OF 2) CARBURETOR REPAIR KIT (291/414CC) RECOIL BOLT KIT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 41
SERVICE NOTES
42
SERVICE NOTES
43
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions. 1.
This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.
2.
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by the manufacturer.
3.
Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must be maintained in accordance with the instructions furnished.
4.
The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original purchase.
5.
This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6.
Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard hardware and normal maintenance.
7.
In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact: HOP Outdoor Products Customer Service Dept. 9335 Harris Corners Parkway Charlotte, NC 28269 USA
In Canada contact: HOP 5855 Terry Fox Way Mississauga, Ontario L5V 3E4
giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased. THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from locale to locale. This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
10.14.13 TH
Printed in the U.S.A.
