Ir To Bluetooth Signal Converter

Transcript

BlueBeam Quick Start Guide IR to Bluetooth Signal Converter Model C-1071A Download complete manual: www.audioauthority.com/product_details/c-1071a 1. CONFIGURING THE IR REMOTE CONTROL Following the instructions for your model of universal remote, add the codes for the C-1071A or BlueBeam to the remote from your remote manufacturer’s database. If the above is not possible, use the PS2 codes (custom macro commands will be deleted) or download the codes in raw hex or .ccf format from www.audioauthority.com/page/software. 2. PAIRING THE BLUEBEAM WITH THE PS3 • Turn off the BlueBeam by removing the batteries and disconnecting the power supply and/or USB cable. • Turn PS3 on and use the PS3 controller to select the following option: SETTINGS > ACCESSORY SETTINGS > REGISTER BD REMOTE. • Set the BlueBeam within 30 feet of the PS3 and power on the BlueBeam (insert batteries, connect power supply, or USB connection to power). The BlueBeam automatically pairs with the PS3 at this point. Manual pairing instructions are in the complete BlueBeam manual download (see above). 3. CHOOSING THE BEST POWER SOURCE The BlueBeam can simply be powered from the PlayStation 3 USB port, but the PS3 does not supply power to its USB port when it is powered off. Therefore you will not be able to turn on the PS3 from your IR remote control if it does not have an additional power source. If you do not wish to use an external AC adapter, use two AA batteries to power the BlueBeam when the PS3 is off. The BlueBeam will automatically draw power from the USB port when the PS3 is on. This way you can control the PS3 as normal and you do not need an external AC adapter. Also battery life will be increased since power is supplied by the USB port whenever the PS3 is turned on. Using “IR Repeater Mode” or using an external IR receiver both require the BlueBeam to be connected to USB power or an external power supply. An AC adapter (Model 571-013) can be ordered from Audio Authority. BlueBeam Quick Start Guide MACROS TAB The macros tab allows the user to define 10 custom macros, which will execute a sequence of commands by activating only one IR command. IR to Bluetooth Signal Converter Model C-1071A The power-off macro is a predefined macro, which will execute a power-off Download complete manual: www.audioauthority.com/product_details/c-1071a sequence which will power off the PS3 by pressing only one button on the IR remote. 1. CONFIGURING THE IR REMOTE CONTROL Select macro Selects which of the 10 macros to edit Following the instructions for your model of universal remote, add the codes Command Selects which command execute for the C-1071A or BlueBeam to theIRremote fromtoyour remote manufacturer’s Duration Specifies the time use in milliseconds to activate current database. If the above is not possible, the PS2 codes (customthe macro command commands will be deleted) or download the codes in raw hex or .ccf format fromPause www.audioauthority.com/page/software. Specifies the time in milliseconds to pause until the next command should be sent Default default button resets the PS3 currently selected macro to 2. PAIRING THEThe BLUEBEAM WITH THE its default values • Turn off the BlueBeam by removing the batteries and disconnecting the power supply and/or USB cable. IR DEVICE CODE TAB • Turn PS3 on and use the PS3 controller to select the following option: By default the BlueBeam responds to IR codes from the device code Sony SETTINGS > ACCESSORY SETTINGS > REGISTER BD REMOTE. DVD1a, but this can be changed to any Sony device code. For ease, it is • Set the BlueBeam 30 commonly feet of the PS3 power on the BlueBeam possible to select within the most usedand device codes directly from the (insert batteries, connect supply, or USB connection power). selection box. Make surepower that you are using a remote that to is able to transmit selected automatically codes, or the pairs BlueBeam willPS3 not respond. Thethe BlueBeam with the at this point. Manual pairing instructions are in the complete BlueBeam manual download (see above). If you have an existing Sony DVD player that conflicts with the default device code, change the device code from “DVD1a” to “DVD2a” 3. BlueBeam CHOOSING THE BEST POWER SOURCE the selection and be press “Save”. In the Remote add TheinBlueBeam canbox simply powered from the Harmony PlayStation 3 USBsoftware, port, new device model name “BlueBeam to powered allow control butathe PS3 doeswith not the supply power to its USB portDVD2a” when it is off. of a BlueBeam the be IR able device DVD2a. Therefore youwith will not to code turn on the PS3 from your IR remote control if it does not have an additional power source. If you do not wish to use an A custom IR device code entered selecting the “Custom” entry external AC adapter, use twocan AA be batteries to by power the BlueBeam when the from the box, and entering the code manually. PS3 is selection off. The BlueBeam will automatically draw power from the USB port when the PS3 is on. This way you can control the PS3 as normal and you do INSTALL not need anMODULE external ACTAB adapter. Also battery life will be increased since Allows for future be downloaded a firmware power is supplied byfeatures the USBtoport whenever theasPS3 is turnedupgrade. on. Using “IR Repeater Mode” or using an external IR receiver both require the BlueBeam to be connected to USB power or an external power supply. An AC adapter REGULATORY COMPLIANCE (Model 571-013) can be has ordered from Audio Authority. The C-1071A BlueBeam been tested for compliance with CE and FCC rules and regulations. The optional power adapter/supply has been tested for compliance with UL, CUL, CE, PSE, and GS regulations and guidelines. This product and its power supply are INSTALLING RoHS compliant. OR CHANGING BATTERIES 4. INSTALLING OR CHANGING BATTERIES 4. 5. USING AN EXTERNAL INFRARED RECEIVER • This product should be installed by qualified personnel. • Do not expose this unit to excessive heat. 5. • USING EXTERNAL INFRARED RECEIVER Install onlyAN in dry, indoor locations. Connect of or any standard IR receiver connecting block to • Cleanthe the emitter unit only output with a dry slightly dampened soft cloth. To change or remove the batteries, remove the two o-rings, lift the top cover and lift the batteries from the battery-holder. Replace them with two AA alkaline batteries, or use USB or AC power as described above. Connect the emitter output of any standard IR receiver connecting block to the IR input on the rear of the BlueBeam using a mono 3.5mm cable. By default the BlueBeam is configured to auto-sense the type of IR receiver connected. Use configuration software to manually select IR receiver type. 6. USING THE BLUEBEAM IN IR REPEATER MODE In Repeater Mode, the BlueBeam repeats IR commands with IR carrier frequencies between 36 and 40 kHz. In this mode, the BlueBeam must be powered by USB or AC adapter, not batteries alone. Using the configuration software, set the IR receiver type to repeater mode. Connect the IR port on the rear of the BlueBeam to an IR emitter or the IR input of an IR distribution block. Non-PS3 commands will be passed to the IR output of the BlueBeam. To change or remove the batteries, remove the two o-rings, lift the top cover andWARNINGS lift the batteries from the battery-holder. Replace them with two AA • Readbatteries, these instructions installing or using this product.above. alkaline or use before USB or AC power as described the IR input on the rear of the BlueBeam using a mono 3.5mm cable. By LIABILITY STATEMENT default the BlueBeam is configured to auto-sense the type of IR receiver Every effort hasconfiguration been made to ensure thatto this product isselect free of IR defects. Audio Authority connected. Use software manually receiver type. cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user of the hardware to check it is suitable his/her requirements andREPEATER that it is installed correctly. All rights are 6. that USING THEforBLUEBEAM IN IR MODE reserved. No parts the of this manual may be reproduced or transmitted by any form or means In Repeater Mode, BlueBeam repeats IR commands with IR carrier electronic or mechanical, including photocopying, recording by any information frequencies between 36 and 40 kHz. In this mode, the or BlueBeam must bestorage or retrieval system without the written consent of the publisher. Audio Authority reserves powered by USB or AC adapter, not batteries alone. Using the configuration the right to revise any of its hardware and software following its policy to modify and/or software, the IR receiver type to or repeater mode. Connect the IR port on improveset its products where necessary desirable. the rear of the BlueBeam to an IR emitter or the IR input of an IR distribution TRADEMARKS block. Non-PS3 commands will be passed to the IR output of the BlueBeam. • If changes are made, you must click SAVE to write them to the device. “Audio Authority” and the double-A symbol are registered trademarks of Audio Authority Corp. Copyright February, 2009. 7. “BlueBeam” USING BLUEBEAM is a trademark of SOFTWARE Audio Authority “Bluetooth” is a trademark of Bluetooth SIG, Inc.cable (requires mini-USB). • Connect BlueBeam to PC using USB 2.0 “PLAYSTATION” is a registered trademark of Sony Computer Entertainment Inc. • Uses existing Windows drivers – does not require additional drivers. “Sony” is a registered trademark of Sony Corporation. other trademarks are you the property of their respective owners. • IfAll changes are made, must click SAVE to write them to the device. • To erase custom settings (and all macros) select the menu option OPTIONS > RESTORE DEFAULT SETTINGS. • To erase custom settings (and all macros) select the menu option LIMITED WARRANTY OPTIONS > RESTORE DEFAULT SETTINGS. If any consumer product from Audio Authority fails due to defects in materials or SETTINGS TAB Authority guarantees SETTINGS TAB that we will replace the defective product at no cost. 7. USING BLUEBEAM SOFTWARE • Connect BlueBeam to PC using USB 2.0 cable (requires mini-USB). • Uses existing Windows drivers – does not require additional drivers. Enable status LED on IR activity Selects if the LED should light up when receiving valid IR commands from an IR remote Flash status LED on low battery level Selects if the LED should flash briefly to indicate low battery level IR receiver • Auto-sense • External, Modulated • External, Demodulated • Repeater Mode Selects if IR should be received through the internal IR receiver, OR through an externally connected IR receiver (both cannot be active at once). If an external IR receiver is used BlueBeam must be powered by USB or DC adapter, not batteries. Power Tracking Bluetooth Pairing Mode workmanship within one year from the date of the original sale to the end-user, Audio Freight charges for the replacement unit will be paid by Audio Authority (ground service only). A copy of the invoice showing dateLED of purchase must be Enable status LED the on item number Selectsand if the should (proof-of-purchase) light up when to constitute valid in-warrantyfrom claim.an Units IRsubmitted activity with the defective unit receiving validaIR commands IR that fail after the warranty period has expired may be returned to the factory for repair at a nominal remote charge, if not damaged beyond the point of repair. All freight charges for out-of-warranty Flash status LEDare the responsibility Selects of if the LED should flash briefly returns for repair the customer. Units returned for to repair must Return Authorization Number by thelevel factory. This is a limited warranty and onhave lowabattery level indicateassigned low battery is not applicable for products which, in our opinion, have been damaged, altered, abused, IRmisused, receiveror improperly installed. Selects IR should be received through either the AudioifAuthority makes no other warranties • Auto-sense internal IRwarranties receiver, as OR an externally expressed or implied, including limitation to through merchantability or fitness for a particular purpose. Additionally, there are no or credits available for service • External, Modulated connected IR allowances receiver (both cannot be active work or installation performedat in once). the fieldIfbyan theexternal end user.IR receiver is used • External, Demodulated • Repeater Mode BlueBeam must be powered by USB or DC adapter, not batteries. The BlueBeam can keep track of the PS3 power state internally, or actively via USB. Power Tracking The BlueBeam can keep track of the PS3 power state internally, or actively via USB. Default is auto. Use manual mode when necessary. 2048 Mercer Road, Lexington, Kentucky 40511-1071 Bluetooth Pairing Mode Default is auto. Use manual mode when Phone: 859-233-4599 • Fax: 859-233-4510 necessary. Customer Toll-Free USA & Canada: 800-322-8346 www.audioauthority.com 752-600 2/10 MACRO The mac execute a The powe sequence remote. Select m Comma Duration Pause Default IR DEV By defau DVD1a, b possible selection the selec If you hav BlueBeam in the sel a new de BlueBeam A custom the selec INSTAL Allows fo REGULAT The C-107 regulations CUL, CE, P RoHS com WARNING • Read the • This prod • Do not ex • Install on • Clean the LIABILITY Every effor cannot be damages a that it is su reserved. N electronic or retrieval the right to improve its TRADEMA “Audio Aut Corp. Cop “BlueBeam “Bluetooth “PLAYSTA “Sony” is a All other tr LIMITED W If any cons workmans Authority g for the rep the invoice submitted the warran charge, if n returns for have a Re is not appl misused, o expressed particular p work or ins 2048 Me Phone: 8 Custome www.aud