Preview only show first 10 pages with watermark. For full document please download

Isa-bus-iso-da

   EMBED

Share

Transcript

ISO-AD32H/L Model No. Bus Analog Input Channels Strain Gauge Input Analog Input Resolution Bipolar Low gain ISA-Bus Analog Input Range (V) Bipolar High Gain Unipolar Low gain Unipolar HIgh gain Channels Resolution Analog Range Output (V) Range (mA) On-Board FIFO Speed AT 32 S.E. 16 DIF. - ISO-813 ISO-LDH/L ISO-DA8 ISO-DA16 AT AT AT 32 S.E. 1 - - - 1 - - 12 bits 12 bits 12 bits - - ±10,±5,±2.5 ±1.25 ±10,±5,±1 ±0.5,±0.1, ±0.05 0~10,0~5, 0~2.5 0~10,0~1, 0~0.1 - ±5,±2.5±1.25, ±0.625,±0.3125 - - - - - - - 0~10,0~5,0~2.5, 0~1.25,0~0.625 - 0~10,0~5, 0~2.5,0~1.25 0~10,0~1, 0~0.1,0.01 - - - - - 8 14 bits ±10,±5 0~5,0~10 16 14 bits ±10,±5 0~5,0~10 0~20,4~20 0~20,4~20 - - 16 TTL Input 16 TTL Output 16 TTL Input 16 TTL Output - 47 - 48 Digital I/O Channels Channel Scan Page AT - - - 1K bytes 200KHz 10KHz - - Yes 45 - 46 51 1K bytes 16KHz 8 isolated input 7 isolated O.C. output 8 TTL output 49 - 50 47 - 48 Isolated Digital I/O, Counter, Relay Output Board Selection Guide Model No. ISO-P32C32 ISO-C64 ISO-P64 ISO-730 P8R8DIO Bus Isolated Input Channels Input Range Isolated Output Channels AT AT AT AT AT AT 16 Driving Capacity Non-isolated D I/O Other Function Connectors Daughter board Page P16R16DIO 32 - 64 16 - 5-24V - 5-24V 5-24V - 5-24V 32 64 - 16 - 16 Open-collector Open-collector 100 mA sink 100 mA sink - - - - Built-in DC/DC 1 x 40-pin 1 x DB-37 On board Fuse, LED 1 x 40-pin 1 x DB-37 Built-in DC/DC 1 x 40-pin 1 x DB-37 DB-37,DN37,DB-8125 DB-37,DN37,DB-8125 DB-37,DN37,DB-8125 52 54 53 44 Open-collector 125V/0.3A 100 mA sink relay 200 mA max. 16 DI 16 DO 4 Form C relay 8 Form C relay Built-in 4 Form A relay 8 Form A relay DC/DC 1 x 40-pin 1 x 40-pin 1 x DB-37 1 x DB-37 1 x DB-37 4 x 20-pin DB-37,DNDB-37,DNDB-37,DN37,DB-8125, 37,DB-8125 37,DB-8125 DB-8025 57 55 56 ? ? ? ?? ? W2@@6Xg? /Xhf ?@f@?he ?W2@@6X?g @@fW2(?f ?W&(MI')X?f? N1hf J5?@e@?he W&(MI')Xg @@e?W&(Y?f W&(YeV')Xf? ?@e?O)Xg 7H?@e@?O)X?g &0Y??N@1g @@eW&(Yg 7@H?e?N@1f? @@@@@@@@@@@@@)g ?J@??@@@@@@@)?g @@g @@?W&(Y?g @@g@@f? @?f@?h ?7@?J(M?@?he?J@5g @@W&(Yh @@g@@f? 3Le?J5?h J@@?.Ye@?heW&(Yg @@@@he @@g@@f? N1e?7H?h .Y@?f@??O)Xg ?W&(Y?g @@V')Xh @@g@@f? ?3L?J5he @?@@@@@@@@@)g W&(Yh ?@@@@@f @@?V')X?g 3@L?e?J@5f? ?V/T.Yhe @?f@?he ?W&(Y?h @@eV')Xg V')XeW&(Yf? S@U?he @?f@?he W&(Yhe @@e?V')X?f ?V')KO&(Y?f? ?W.R/Xhe @?f@?he 7@Y?he @@fV')Xf V4@@0Yg? O.Y?V/K?h @?f@?he @@@@@@@@g @@f?V4)f ? O20Ye?V46K?g @?f@?he ? @@0Mg?I4@g @?f@?he ? ? ? ?? ? ? ? ? ? ? ? ? ?? ?? ?W&?e? ?W&?e? @@@@@@@@@?f ?75?e? ?W2@@?h @@@@@@@@@?f?75?e? W2@6X?g W2@6X?g W@5?f J@H?e? ?&@@@?h W@5?fJ@H?e? ?W.M?I/Xg 75f? 75f??W.M?I/Xg 7@H?f?J@Hf? ?@@?h 7@H?f ?7H?eN1g ?7H?eN1g ?J@Hf?J@f?@L?f ?J@5g ?@@?h ?J@5g J@f?@L?f ?75?f? ?7@Hg?75?f? ?7@Hg 7@f?@1?f J@H?f??@@?h J@H?f?7@f?@1?f J@5?g75g? ?@@?h J@5?g @@f?@@?f 75g?@@f?@@?f 7@H?g 7@H?g @@f?@@?f ?J@Hg??@@?h ?J@Hg?@@f?@@?f ?J@5h ?J@5h 3@f?@5?f ?75?g??@@?h ?75?g?3@f?@5?f ?7@Hh ?@@?h?7@Hh N@f?@H?f N@f?@H?f J@H?g??@@?h J@H?g??3L?eJ5g J@5?h ?3L?eJ5g 75h? 75h? 7@H?h ?@@?hJ@5?h 7@H?h ?V/K?O.Yg (Yh??@@?h (Yh??V/K?O.Yg @@he @@he V4@0Y?g ? ? V4@0Y?g ? ? ? ? ? ? ? ? ?? ?? ? ? ? ? W2@@@6X?g W2@@@6X?g ?W2@@?h &0M?I')Xg &0M?I')Xg ?&@@@?h ?N@1g ?N@1g?@@?h ?J@5g @@f O&(Yg @@f ?J@5g O&(Yg?@@?h ?@@?h @@@@h @@@@h?@@?h I')Xg I')Xg?@@?h ?N@1g ?N@1g?@@?h @@g @@g?@@?h ?J@5g ?J@5g?@@?h '6K?O&(Yg @@f '6K?O&(Yg ?@@?h V4@@@0Y?g @@f V4@@@0Y?g?@@?h ? ? ? ?? ? ?@@@@@6Xf? ?@6XgW2@?f ?O)Xg ?O)Xg W2@@@6X?g W2@?g ?@@??I')X?e? ?@@1g7@@?f @@@@@@@@@@@@@)g @@@@@@@@@@@@@)g &0M?I')Xg?W&@@?g ?@@?eN@1?e? ?@@@L?e?J@@@?f?W(Mhf?W([email protected]@@?g ?@@?e?@@?e? ?@@@1?e?7@@@?f @KO&Y??O)Xh ?@K?O&Y?eO)X?g ?W.Y?@@?g ?@@?eJ@5?e? ?@@?@LeJ@?@@?f @@@@@@@@@)h ?@@@@@@@@@@@)?g?J@5g O&(Yg W.Y??@@?g ?@@??O&(Y?e? ?@@?31e75?@@?f @?g@Hh ?@e@?e@??@H?g @@@@h ?W.Ye?@@?g ?@@@@@0Yf? ?@@?N@e@H?@@?f @@@@@@@@@?h ?@e@@@@@??@hI')Xg ?7Y?e?@@?g ?@@?h? ?@@??3@@5??@@?f @?g@?h ?@e@?e@??@h?N@1g ?@@@@@@@@@@?f ?@@?h? ?@@??N@@H??@@?f @@@@@@@@@?h ?@e@?e@??@h @@g ?@@?g ?@@?h? ?@@?e@@e?@@?f @?g@?h ?@e@@@@@??@h ?J@5g ?@@?g ?@@?h? ?@@?g?@@?f @@@@@@@@@?h ?@e@?e@??@h '6K?O&(Yg ?@@?g ?@@?h? ?@@?g?@@?f ?W(M?I'Xhe ?@e@?e@??@h V4@@@0Y?g ?@@?g ? ?O20Y?eV46Xh ?@@@@@@@@@@@h ? @0M?gI/h ?@M?gI@h ? ? ? ?? ? ? ISA-Bus ■ General Environment Pin Assignments Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% Dimensions: 173 mm x 122 mm AI 0 AI 1 AI 2 AI 3 AI 4 AI 5 AI 6 AI 7 AI 8 AI 9 AI10 AI 11 AI 12 AI 13 AI 14 AI 15 A. GND +5V N.C. Software ■ ISO-AD32 Development Toolkit for DOS ■ ISO-AD32 Development Toolkit for Win95 ■ ISO-AD32 Development Toolkit for WinNT Order Description ■ ISO-AD32H: 32 channel high gain isolated analog input ■ ISO-AD32L : 32 channel low gain isolated analog input Options 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 AI 16 AI 17 AI 18 AI 19 AI 20 AI 21 AI 22 AI 23 AI 24 AI 25 AI 26 AI 27 AI 28 AI 29 AI 30 AI 31 N.C. D. GND ■ DN-37: I/O connector block with DIN-rail mounting and 37-PIN D-SUB connector on it ■ DB-1825: Screw Terminal Board Note: AIn: Analog Input Channel A. GND: Analog Ground D. GND: Digital Ground +5V: On Board DC to DC Converter; +5V Output ■ ISO-AD32 LabVIEW Development Toolkit for Win95 ■ ISO-AD32 LabVIEW Development Toolkit for WinNT Distribué par : 2 rue René Laennec 51500 Taissy France Fax: 03 26 85 19 08, Tel : 03 26 82 49 29 46 Email : [email protected] Site web : www.hvssystem.com 4-20mA current sink to ground from each converter Double-buffered D/A latches Command set programming Software Calibration 16 channel DI, 16 channel DO iun vent86674 n I .0 .C. R.Otent No Pa Applications Programmable voltage source Programmable current sink Harsh environment operation Process control Specifications Functional Description The ISO-DA8/16 is an Bus-type isolated 14-bit D/A card for PC/AT compatible computers. The optical isolation of the ISO-DA8/16 can operate with up to 2500Vrms of common-mode voltage. The ISO-DA8/16 offers 8/16 channel double-buffered analog outputs. The output range may be configured in different ranges: ±10V, ±5V, 0~10V, 0~5V voltage output or 4 to 20mA / 0 to 20mA current loop sink. The innovative design improve several drawbacks of the conventional isolated D/A card. For example : 1). Jumperless, Trimless 2). The poweron value of analog output can be pre-defined by the user and stored in the on board EEPROM 3) The calibration is performed under software control, thus eliminating manual trimpot adjustments. The calibration data is stored in EEPROM. Easy recalibration ensures the accuracy of the board 4). Every channel can be selected as voltage or current output 5). High channel count output can be implemented in half size. Voltage Output Range : Unipolar: 0~5V or 0~10V Bipolar: +/-10Vor,+/- 5V Current drive: +/-5mA Absolute accuracy: 0.01% FSR typical Power on state: programmable Current Output Range : 0-20mA or 4-20mA Absolute Accuracy: 0.1% FSR typical Excitation voltage range: + 7 V to +40V Power On state: programmable Digital I/O Inputs: 16 channels/ TTL levels Outputs: 16 channels/ TTL levels Features AT bus 2500VDC photo-isolation protection 8/16 channel, 14-bit analog output Unipolar or bipolar outputs available from each converter Voltage/Current output from each converter Output type ( Unipolar or bipolar) and output range (0-5V,+/-5V,0-10V,+/-10V) can be software programmable Stability Offset temperature coefficient: +/- 50µV/°C Gain temperature coefficient: +/- 10ppm/°C 47 ISA-Bus Analog Outputs D/A converter: Quad 14-Bit MDAC Channels: 8/16 independent Resolution: 14 bits Type: double-buffered, multiplying Integral linearity: 0.006% FSR; typical Differential linearity: 0.006 % FSR; typical ISA-Bus Power Requirements ISO-DA8: +5VDC @800mA max. ISO-DA16: +5VDC @1400mA max. Pin Assignment V0 V1 V2 V3 AGND V4 V5 V6 V7 AGND V8 V9 V 10 V 11 AGND V 12 V 13 V 14 V 15 General Environment Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% Dimensions: 182 mm x 122 mm Software ISO-DA Development Toolkit for DOS ISO-DA Development Toolkit for Win95 ISO-DA Development Toolkit for WinNT Order Description ISO-DA8: 8 Channel 14 BIT Isolated Analog Output Board ISO-DA16: 16 Channel 14 BIT Isolated Analog Output Board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 I0 I1 I2 I3 AGND I4 I5 I6 I7 AGND I8 I9 I 10 I 11 I 12 I 13 I 14 I 15 Note: AOn: Analog Voltage Output Channel IOn: Current Loop Output Channel A.GND: Analog Ground Options DN-37: I/O connector Block with DIN- Rail mounting DB-37: 37-pin directly connect board ADP-20/PCI: 20-pin Extender ISO-DA LabVIEW Development Toolkit for Win95 ISO-DA LabVIEW Development Toolkit for WinNT 48 Second order low pass filter build-in Direct connection to strain gauge type loadcell 8-channel 12-24V isolated digital input 7-channel isolated open-collector digital output Programmable 8 bits LED indicator Command set programming n ntiu6674 e v n I . 08 .C. R.Otent No Pa Applications Strain gauge type loadcell measurement Dynamic force on line monitoring system Dynamic pressure measurement Specifications Functional Description The ISO-LD series is a Bus-type isolated loadcell input board. The isolation inputs can operate with up to 500Vrms of common-mode voltage. The ISO-LD series features a 12 bit analog-to-digital converters, on board 1 K bytes FIFO buffer, one loadcell signal input channel, one analog input channel, 8-channel 12-24V isolated digital inputs, 7channel isolated open-collector digital outputs, one programmable 8-bit LED indicator to indicate the magnitude of strain gauge input signal.The ISO-LD series board is suitable for static force measurement and dynamic force analysis. Because there are on board excitation voltage, high gain amplifier, user don't have to buy any excitation voltage and signal conditioning module. The board also have some special features, such as: 1). 12-bit programmable offset voltage. Therefore the user can cancel the DC bias and amplify the AC signal; 2). The isolated structure eliminate the ground loop noise and protect your computer; 3). On board FIFO buffer support gap-free A/D conversion under DOS environment; 4). Except the loadcell input channel, there are a lot digital I/O and one analog input channel. The user can implement a measurement and analysis system. ISO-LDH Input Range Analog input range: 0~10V, 0 ~1V, 0~0.1V, 0~0.01V Strain Gauge input range: 0 ~ 37.5mV Resolution Features Gain Input range(mV) 400 0~37.5 4,000 0~15 40,000 0~12.75 ISO-LDL Input Range Normal input range: 0~10V, 0~5V, 0~2.5V, 0~1.25V Loadcell input range: 0 to 37.5mV Loadcell offset voltage adjustment: 0 to -5V, 8-bit Resolution AT bus 500 VDC photo-isolation protection one strain gauge input channel One analog input channel Built-in 1K bytes FIFO Excitation voltage for loadcell: 12V, 50mA Maximum gain up to 40,000 Programmable 12-bit resolution, DC offset voltage (0~5V) 49 ISA-Bus Analog Input Specifications Channels: 1 loadcell input channel & 1 analog input channel Resolution: 12-bits Conversion rate: 16 KS/s max Nonlinearity: +/- 0.01 % Gain error: 0.005% of reading maximum Input Impedance: 10,000MΩ||6pF bias current: +/- 3 nA (maximum) Input offset current: +/- 2 nA (maximum) CMRR: 90 dB ( Minimum) Recommended warm-up time: 10 minutes On chip sample & hold ISA-Bus Gain Input range(mV) 400 0~37.5 800 0~25 16,00 0~18.75 3,200 0~15.625 S TYPE LOADCELL SENSORS There are a lot Strain Gauge type LOADCELL sensors available for the ISO-LD board. The user can find the S -50 Loadcell from options to match ISO-LD board to implement a loadcell measurement starter kit. Specifications Loadcell Offset Voltage Adjustment 0 to -5V, 12-bit resolution Digital I/O 8 photo-isolated 12~24V digital input 7 isolated open-collector digital output (100mA) 8 TTL/LED output Capacity: 60Kg Rated Output: 2 mV/V Total error: 0.05% Repeatability: 0.03% Creep: 0.05%/30 min Resolution: 1/10,000 Input Resistance: 410 +/- 15Ω Output Resistance: 350 +/- 5Ω Max. Excitation Voltage: 20V Compensated Temperature Range: -10°C ~ 50°C Safe Temperature Range: -20°C ~ 70°C Temp. Effect on Rate Output: 0.03% Load/10°C Zero Balance: ±5% R.O. Safe Overload Rating: 150% Cable Length: 2M Cable connection: Input:Red(EX+), Black(EX-) Output: Green(LS+), White(LS-) Software ISO-LD Development Toolkit for DOS Order Description ISO-LDH: High gain loadcell input and digital I/O board ISO-LDL: Low gain loadcell input and digital I/O board Options DN-25 I/O Connector block with DIN rail mounting S-50: S type loadcell Power Requirements: +5V @400mA(max) General Environment Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% Dimensions: 190 mm x 105 mm Free: Application notes - A002 Loadcell sensor: EX+ LS+ LS- EX+ : Excitation Voltage + EX- LS+ : Loadcell+ LS- : Loadcell- Input Wiring Examples Full-Bridge EX- : Excitation Voltage- 50 Specifications 0V 300lation Iso Analog Input Specifications Channels : 32 single-ended Resolution : 12 bits Conversion rate : 10KS/s max. Input impedance : 10 MΩ Overvoltage protection : +/-35V Accuracy : 0.01% of reading +/- 1 bit Linearity : +/- 1 bit On chip sample & hold Zero drift : +/-25ppm/°C of FS max. Power Requirements: +5V @850mA max. General Environmental Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% non-condensing Dimensions: 174 mm x 122 mm NAPDOS : Library and demo program for DOS Functional Description Software ISO-813 Development Toolkit for DOS ISO-813 Development Toolkit for Win95 ISO-813 Development Toolkit for WinNT Order Description ISO-813 32 channel isolated analog input board Options DB-8325: Daughter board with signal conditioning circuitry DB-37: Directly connect signals to the back of ISO-813 DN-37: I/O connector block with DIN-Rail mounting and 37-PIN D-SUB connector on it ISO-813 LabVIEW Development Toolkit for Win95 ISO-813 LabVIEW Development Toolkit for WinNT Features 32 single-ended analog input channels 12-bit A/D converter ( ADS 774 or equivalent) 3,000Vdc photo-isolation protection Analog input range Bipolar : +/- 5V, +/-2.5V, +/-1.25V, +/0.625V, +/-0.3125V Unipolar: 0-10V, 0-5V, 0-2.5V, 0-1.25V, 0-0.625V Programmable gain control 3000V DC/DC converter build in A/D trigger mode: Software Trigger A/D data transfer mode : polling Applications Data acquisition Harsh environment operation Signal isolation 51 ISA-Bus The ISO-813 is a bus-type isolated 12-bit A/D board for PC/AT compatible computers. It's isolation range is increased to 3000 V and extend the application field to real industry application. It is backward compatible to 813 families. Comparing to PCL-813 or ACL-8113, the ISO-813 add X 16 Programmable Gain Control range . FPGA on board can increase the stability of this board. It is the most cost effective isolated A/D board in the world. If the user need high sampling rate, differential input and FIFO onboard isolated A/D card, please refer to our ISOAD32. Applications Factory Automation Product Test Laboratory Automation Specification Isolated Input Type : Isolated current input Isolation Voltage : 3750V( Using External Power); 3000V ( Using internal Power) Input voltage : 3.5V to 30V Input impedance : 3K (DC 24V, 7.67mA) for each channel ) Response time: 10Khz Max Isolation Output Type : Isolated open-collector : 100mA per channel External voltage : 30V (Max.) Response time: 10Khz Max Power requirements : +5V, 600mA (typical) General Environmental Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% non-condensing Dimensions: 163 mm x 115 mm ISA-Bus Functional Description The ISO-P32C32 has 32 channels of optically isolated digital inputs and 32 channels of optically isolated digital outputs, arranged into four isolated banks. Each input channel use a photo-coupler input which allows either internal isolated power supply or external power selected by jumper. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated input channels 0-15 are designed into group A and channels 16-31 are designed into group B. Isolated output channels are designed into group C and Group D. The power supply of the input port may use the external power or the power from the PC side using DC/DC converter. The power supply of the output port should use the external power. This interface board is easily installed in any PC/AT/XT. The board interface to field logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The ISOP32C32 has one 37-pin D-Sub connector and one 40-pin male header. The 40-pin to DB-37 flat-cable is used to fixed with the case. The user can connect the digital signal through the second D-Sub connector . Each D-Sub connector contains 16 input channels and 16 output channels. Software ISO Development Toolkit for DOS ISO Development Toolkit for Win95 ISO Development Toolkit for WinNT Order Description ISO-P32C32 : 32-channel isolated Digital Input and 32 -channel isolated Open-Collector Output Board OPTIONS DB-37: Directly connect signals to the back of ISOP32C32 DN-37: I/O Connector Block with DIN-Rail Mounting and 37-PIN D-SUB Connector ISO LabVIEW Development Toolkit for Win95 ISO LabVIEW Development Toolkit for WinNT Pin Assignment GND_DO(-) 1 2 DI_0 3 DI_1 4 DI_2 5 DI_3 6 DI_4 7 DI_5 8 DI_6 9 DI_7 10 DI_8 11 DI_9 12 DI_10 13 DI_11 14 DI_12 15 DI_13 16 DI_14 17 DI_15 Power_A(+) 18 GND_DO(-) 19 Features 32-channel optically isolated digital input 32-channel optically isolated digital output /open -collector DC/DC converter build-in Four isolated bank. 3000V DC isolation voltage Interrupt level: 3,4,5,6,7,9,10,11,12,14,15 Interrup source : channel 0 and channel 15 52 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 GND_DO(-) DO_0 DO_1 DO_2 DO_3 DO_4 DO_5 DO_6 DO_7 DO_8 DO_9 DO_10 DO_11 DO_12 DO_13 DO_14 DO_15 Power_DO(+) Specifications Isolation Input Type : Isolated current input Isolation Voltage : 3750V( Using External Power); 3000V ( Using internal Power) Input voltage : 3.5V to 30V Input impedance : 3K (DC 24V, 7.67mA) for each channel ) Response time: 1Khz Max Power requirements : +5V 400mA (typical) General Environmental Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% non-condensing Dimensions: 163 mm x 115 mm Software ISO Development Toolkit for DOS ISO Development Toolkit for Win95 ISO Development Toolkit for WinNT Functional Description The ISO-P64 has 64 channels of optically isolated digital inputs, arranged into four banks. Each input channel use a photo-coupler input which allows either internal isolated power supply or external power selected by jumper. Isolated input channels 0-15 are designed into group A, channels 16-31 are designed into group B, channels 32-47 are designed into group C and channels 48-63 are designed into group D. The power supply of the input port may use the external power or the power from the PC side using DC/DC converter. The board interface to field logic signals, eliminating groundloop problems and isolating the host computer from damaging voltages. The ISO-P64 has one 37pin D-Sub Connector and one 40-pin male header. The 40-pin to DB-37 flat cable is used to fix with the case. The user can connect the digital signal through the second D-Sub connector. Each D-Sub connector contains 32 input channels. Order Description OPTIONS DB-37: Directly connect signals to the back of ISO-P64 DN-37: I/O Connector Block with DIN Rail Mounting and 37-PIN D-SUB Connector ISO LabVIEW Development Toolkit for Win95 ISO LabVIEW Development Toolkit for WinNT Pin Assignment GND1 DI_0 DI_1 DI_2 DI_3 DI_4 DI_5 DI_6 DI_7 DI_8 DI_9 DI_10 DI_11 DI_12 DI_13 DI_14 DI_15 PWR1 NC Features 64-channel optically isolated digital input DC/DC converter build-in Four isolated bank 3000V DC isolation voltage Applications Factory Automation Product Test Laboratory Automation 53 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 GND1 DI_16 DI_17 DI_18 DI_19 DI_20 DI_21 DI_22 DI_23 DI_24 DI_25 DI_26 DI_27 DI_28 DI_29 DI_30 DI_31 PWR2 ISA-Bus ISO-P64: 64 channel isolated Digital Input Board Specifications Isolation Output Type : Isolated open collector : 100mA per channel External voltage : 30V (Max.) Response time: 1Khz Typical Power requirements : +5V 800mA (typical) C64 General Environmental Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% non-condensing Dimensions: 163 mm x 115 mm P32C32 P64 Software ISO Development Toolkit for DOS ISO Development Toolkit for Win95 ISO Development Toolkit for WinNT ISA-Bus Functional Description The ISO-C64 has 64 channels of optically isolated digital outputs, arranged into four isolated banks. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated output channels are designed into group A,B,C,D. The power supply of the output port should use the external power. This interface board is easily installed in any PC/AT/XT. The board interface to field logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The ISO-C64 has one 37-pin DSub Connector and one 40-pin male header. The 40-pin to DB-37 flat cable is used to fixed with the case. The user can connect the digital signal through the second D-Sub connector . Each D-Sub connector contains 32 output channels. Order Description ISO-C64 : 64 -channel isolated Digital Output Board OPTIONS DB-37: Directly connect signals to the back of ISO-C64 DN-37: I/O Connector Block with DIN Rail Mounting and 37-PIN D-SUB Connector ISO LabVIEW Development Toolkit for Win95 ISO LabVIEW Development Toolkit for WinNT Pin Assignment GND_A(-) 1 2 DO_0 3 DO_1 4 DO_2 5 DO_3 6 DO_4 7 DO_5 8 DO_6 9 DO_7 10 DO_8 11 DO_9 DO_10 12 DO_11 13 DO_12 14 DO_13 15 DO_14 16 DO_15 17 Power_A(+) 18 19 N.C. Features 64-channel optically isolated digital output /open collector Four isolated bank. 3750V DC isolation voltage Applications Factory Automation Product Test Laboratory Automation 54 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 GND_B(-) DO_16 DO_17 DO_18 DO_19 DO_20 DO_21 DO_22 DO_23 DO_24 DO_25 DO_26 DO_27 DO_28 DO_29 DO_30 DO_31 Power_B(+) Specifications Functional Description The ISO-730 has 32 Isolated digital I/O channels (16 DI and 16 DO) and 32 TTL digital I/O channels. Each of the 16 isolated digital input channel accept voltage from 5V to 24V and has a resistance of 1.2KΩ. Every eight input channels use one external common ground. For example, channel 0-7 use EI.COM1 and channel 8-15 use EI-COM2. Each of the 16 isolated digital output channels equipped a darlington transistor. Every eight output channels use the common emitters. The power supply of the output port should use the external power. The channels 0-7 use EO-COM1 and channels 8-15 use EO-COM2. This interface board is easily installed in any PC/AT/XT. The board interface to field logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The ISO-730 has one 37-pin D-Sub Connector and four on-board 20-pin flat-cable connectors. It is fully compatible to PCL-730. Software ISO Development Toolkit for DOS ISO Development Toolkit for Win95 ISO Development Toolkit for WinNT Features 32 isolated DIO channels 32 TTL-level DIO channels ( Non-isolated) DC/DC converter build-in Two separate 20-pin connectors for isolated input and output channels. Two separate 20-pin connectors for non-isolated input and output channels. 2500Vdc isolation voltage Interrupt level: 2,3,4,5,6,7 Order Description ISO-730 : 32-channel isolated Digital I/O board Options DB-37 Directly connect signals to the back of ISO-730 DN-37 I/O Connector Block with DIN Rail Mounting and 37-PIN D-SUB Connector ADP-20: 20-pin Extender ISO LabVIEW Development Toolkit for Win95 ISO LabVIEW Development Toolkit for WinNT Applications Factory Automation Product Test Laboratory Automation 55 ISA-Bus Digital Input 16 Optical-isolated inputs Type : Isolated current input Isolation Voltage : 2500Vdc Input voltage : 5V to 24Vdc Input impedance : 1.2KΩ, 0.5W Response time: 10Khz Max. 16 TTL-level inputs Input voltage: High : 2.0V min. Low: 0.8V max. Input load: High: 0.05mA max. @2.7V Low: 0.4mA max. @0.5V Response time :30KHz typical Digital Output 16 optical-isolated outputs Output voltage: open collector 5 to 40Vdc Isolation voltage : 2,500Vdc Sink current: 200mA max. Response time : 10KHz max. 16 TTL-level Outputs Output voltage: High : Source 0.4mA at 2.4V min. Low: Sink 8 mA at 0.5V max. Interrupt Source: Channel 0 and 1 of Isolated DI port or channel 0 and 1 of TTL DI port General Environmental Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% non-condensing Dimensions: 172 mm x 124 mm Output channel 4-7 are Form A Operating time: 5 m Sec Release time: 10m Sec Expected life > 100, 000 times (at 30V/1 A) Inputs Channels: 8 Type: Non-polarized opto-isolated, (PC-814) Input Voltage: AC/DC 5-24V or VAC (50 -1 K Hz) Input Impedance: 1.2 KΩ Response Time: 20 µS (without filter) 2.2 mS (with filter) Isolation: 500 V channel-channel & channel-ground General Environment Operating temp: 0-50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% Dimensions: 145 mm x 105 mm ISA-Bus Functional Description The P8R8 DIO is an 8 Isolated input and 8 relay output interface board designed for control and sensing applications. This board is easily installed in any PC/AT/XT or compatible computer. The P8R8 DIO Provides 8 electromechanical relay outputs and 8 optically isolated inputs. The P8R8 DIO can be used in various applications including load switching, external switching, contact closure, and others. Software DIO Development Toolkit for DOS DIO Development Toolkit for Win95 DIO Development Toolkit for WinNT Order Description P8R8DIO: Isolated 8 Digital Input/8 Relay Output Board Options Features DB-37: Directly connect to the back of P8R8DIO DN-37: I/O Connector Block with DIN Rail Mounting and 37-PIN D-SUB Connector DIO LabVIEW Development Toolkit for Win95 DIO LabVIEW Development Toolkit for WinNT 8 Relay output Channel 8 optically isolated digital input channels DC signal Input with filter or without filter. AC signal input with filter Power Requirements: +5V @120mA(max.); +12V @ 180 mA (max.) Pin Assignment Applications Factory Automation Product Test Laboratory Automation Security Control Specifications Relays Relay output Channels: 8 Contact Rating: 0.3 A; 120V AC/DC / 1A; 30V DC Contact arrangement: Output channel 0-3 are Form C Note: NO: Normal Open NC: Normal Close Com: Common 56 DInH: Digital Input High DInL: Digital Input Low Operating time : 5m Sec Release time : 10m Sec Expected life > 100,000 times (at 30V/1A) Inputs Channels: 16 Type: Non-polarized OPTO-isolated , (PC-814) Input Voltage: AC/DC 5-24V or VAC Feq:50~1Khz Input Impedance: 1.2 KΩ Response Time: 20µS (without filter) 2.2mS (with filter) Isolation: 500V channel-channel & channel-ground General Environment Operating temp: 0 - 50°C Storage temp: -20°C to 70°C Humidity: 0 to 90% Dimensions: 175 mm x 121 mm Functional Description The P16R16 DIO is a 16 isolated digital input and 16 relay output interface board designed for control and sensing applications. This interface board is easily installed in any PC/AT/XT or compatible computer . The P16R16 DIO Provides 16 electromechanical relay outputs and 16 optically isolated inputs. The P16R16 DIO has two 37-pin D-Sub Connectors and the function is equal to two P8R8DIO. Software Order Description P16R16DIO: Isolated 16 Digital Input/16 Relay Output Board Features Relay output Channel Optically isolated digital input channels AC/DC signal Input; AC signal input with filter Power Requirements: +5V/200mA(max.); +12V/260 mA (max.) Options DB-37: Directly connect signals to the back of P16R16DIO DN-37: I/O Connector Block with DIN Rail Mounting and 37-PIN D-SUB Connector DIO LabVIEW Development Toolkit for Win95 DIO LabVIEW Development Toolkit for WinNT Applications Factory Automation Product Test Laboratory Automation Security Control The pin Assignment of P16R16DIO is the same as P8R8DIO Specifications Relays Relay output Channels:16 Contact Rating: 0.3 A;120V AC/DC /1A; 30V DC Contact arrangement: Output channel 0-3, 8-11 are Form C; Output channel 4-7, /12-15 are Form A 57 ISA-Bus DIO Development Toolkit for DOS DIO Development Toolkit for Win95 DIO Development Toolkit for WinNT