Ism Mtp Ut 4da Output Board Installation Notes

Transcript

ISM MTP UT 4DA Output Board Installation Notes ISM MTP UT 4DA The Extron ISM MTP UT 4DA is a twisted pair transmitter board for the ISM 824 with four RJ-45 outputs, two RS-232 inserts, and local audio output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. For full operating details of the ISM refer to the 1 2 3 4 ISM 824 User’s Manual, online at www.extron.com. Tx Rx BUFFERED OUTPUTS INSERT 1/2 LOCAL AUDIO OUTPUT RS 232 L INSERT 3/4 R Tx Rx To install an output board in the ISM 824 base unit, 1. Turn off the ISM 824, and remove the power cord. Repeat for all connected devices. Extron ISM 824 2. At the rear, select an open slot, or take out the blank plate from the desired output port by removing the two retaining screws (top and bottom), and lifting the blank away. Integration Scaling Matrix Switcher UT TP OU 8 R/ Y R- Y G/ UT TP OU 5 3 H/ HV R/ Y R- TS 2 PU OUT 8 R/R- board in place. Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board. 7 6 4 V SS PA RU TH -01 547 70- V B/C Y B- Y G/ VID TS 5 INPU H/ HV H/ HV Y G/ VID V B/ Y B- Y B/ Y B- Y R/R- Y Y G/ G/ 1 N Re-use the screws to secure the new output Align output board with top and bottom plastic guides. B/ Y B- R/ Y R- UT TP OU UT TP OU B/C Y B- H/HV H/HV V IV. UN ER AL SC -01 544 70- 7 R/ Y R- 3 2 RU 1 ACT LINK T SE LAN RE TH PA V 2 Y EO VID ER AL SC -01 545 70- G/ B/ Y B- 1 H/ HV 8 7 V 6 TS INPU RS232/RS422 REMOTE SS 5 Example Output Board Installation 4 3 AN SCNV. CO -01 546 70- 2 3. Remove the board from its outer box and anti-ESD bag, holding the boards by the rear frame. 100 - 240 1.2A 60 50/ X. MA Hz 1 4. With the board upright, align the front (non connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it home firmly, and secure it with the retained screws. 5. If applicable, repeat steps 2 through 4 for any other output boards. 6. Power on the ISM 824. The new output board(s) is auto-detected, and takes approximately 30 seconds to initialize. The LCD display indicates the new board type, New ISM MTP UT 4DA slot used, and counts down the initialization time. See inset for example Slot #3 18 display for a new ISM MTP UT 4DA board installed in Slot #3. Pins: 12345678 7. Using suitable twisted pair cables connect any MTP receiver, DA, or switcher to the RJ-45 twisted pair outputs on the installed boards. See wiring details at right. N Use the same standard at both ends of the twisted pair cable. 8. Insert a 5-pole captive screw connector from an audio device into the local audio output connector for balanced or unbalanced stereo audio. Wire the connector as shown below. R Right Balanced Stereo Output Tip NO GROUND HERE. Sleeve(s) Tip NO GROUND HERE. RJ-45 Connector Left R Left Insert Twisted Pair Wires L L Tip Ring Sleeve(s) Tip Ring Pin Right Unbalanced Stereo Output CAUTION For unbalanced audio, connect the sleeve(s) to the center contact ground. DO NOT connect the sleeve(s) to the negative (-) contacts. T568A Wire color T568B Wire color 1 White-green White-orange 2 Green Orange 3 White-orange White-green 4 Blue Blue 5 White-blue White-blue 6 Orange Green 7 White-brown White-brown 8 Brown Brown NOTE If you are using Enhanced Skew-Free™ A/V cable, use the TIA/EIA T568A standard only. . (Continued on reverse side) ISM MTP UT 4DA Output Board Installation Notes, cont’d RS-232 Commands See below for board specific SIS™ commands. ISM MTP UT 4DA 9. Connect a control device to RS-232 insert 1/2 (for outputs 1 and 2), or insert 3/4 (for outputs 3 and 4). This allows bidirectional, pass-through control signals to and from the control device and the MTP devices on ports 1 and 3, and unidirectional pass-through signals from the control device on ports 2 and 4. Ports 1 and 2 always receive the same RS-232 command signal, but only port 1 allows for bidirectional communications. The same is true for ports 3 and 4, where port 3 allows for bidirectional communications (see right). Tx Rx BUFFERED OUTPUTS INSERT 1/2 LOCAL AUDIO OUTPUT RS 232 L R INSERT 3/4 Tx Rx 1 2 3 4 Unidirectional RS-232 Commands BUFFERED OUTPUTS 1 Transmit (Tx) Receive (Rx) Ground (Gnd, ) ISM MTP UT 4DA configuration menu Using the front panel menu buttons (Menu and Next), the ISM MTP UT 4DA board configuration menu can be accessed. From the Output Configuration screen, press Next until reaching the #x ISM MTP menu (see the image at right). Using the front panel adjustment knobs ({ [), change the settings as desired. 2 3 4 Bidirectional Output Card Configuration Power up input and output devices and create the desired ties. Select Ouptut #x ISM MTP UT 4DA Next Prepeaking #x On Next RS-232 Insert 1/2 On Next RS-232 Insert 3/4 On Next Board specific SIS commands table Alternatively, the ISM MTP UT 4DA board can be configured with specific SIS commands. Command ASCII command Response (switcher to host) Additional description (host to switcher) Local RS-232 ports Enable EX!*X@*1LRPT X!LrptX@*1] Enable RS-232 insert X@ to control output X!. Disable EX!*X@*0LRPT X!LrptX@*0] Disable RS-232 insert X@ controlling output X!. View EX!*X@LRPT X#] View the RS-232 status X# for output X!. Output Pre-peaking Turn on EX!*X$*1OPEK X!OpekX$*1] Turn pre-peaking on for output X! to MTP sub-output X$. Turn off EX!*X$*0OPEK X!OpekX$*0] Turn pre-peaking off for output X! to MTP sub-output X$. View status EX!*X$OPEK X#] View the pre-peaking status X# for output X!. N X! = ISM 824 output number, 3,5,7,8 (i.e. the slot/port occupied by the ISM MTP UT 4DA) X@ = RS-232 number 0 = insert 1/2, 1= insert 3/4 X# = Setting value 0 = off, 1= on X$ = Sub-output number (setting for each MTP output on each card) 1,2,3,4 Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.4664 FAX Inside USA / Canada Only Inside Europe Only Inside Asia Only © 2009 Extron Electronics. All rights reserved. Inside China Only +86.21.3760.1568 +86.21.3760.1566 FAX 68-1123-60 Rev A 02 09