Ism Sc Output Board Installation Notes

Transcript

ISM SC Output Board Installation Notes SCAN CONVERTER The Extron ISM SC is a scan converter output board for the ISM 824 with four BNC connectors and a local audio output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. For full operating details of the ISM refer to the ISM 824 User’s Manual, online at www.extron.com. L R 8 Align output board with top and bottom plastic guides. Y 5 B/ Y B- R/ Y R- UT H/ HV TP OU 3 Y G/ H/ HV B/ Y B- H/ HV Y G/ VID V B/ Y B- Y G/ 1 Y R/ Y R- TS 2 PU OUT Y V SS PA RU TH -01 547 70- V B/C Y B- Y G/ VID 4 R/ Y R- G/ UT R/R- board in place. Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board. 8 TP OU 7 6 C UT TP OU R/R- TS 5 R/ R-Y Integration Scaling Matrix Switcher 2. At the rear, select an open slot, or take out the blank plate from the desired output port by removing the two retaining screws (top and bottom), and lifting the blank away. INPU Y Extron ISM 824 1. Turn off the ISM 824, and remove the power cord. Repeat for all connected devices. N Re-use the screws to secure the new output G/Y B/ B-Y VID To install an output board in the ISM 824 base unit, UT TP OU B/C Y B- H/HV H/HV V IV. UN ER AL SC -01 544 70- 7 R/ Y R- 3 2 RU 1 SS PA V ACT LINK T SE LAN RE - 240 1.2A G/ B/ Y B- 1 H/ HV 8 7 INPU RS232/RS422 60 50/ X. MA Y EO VID ER AL SC -01 545 70- 2 V 6 TS REMOTE 100 TH 5 Example Output Board Installation 4 3 2 Hz AN SCNV. CO -01 546 70- 1 3. Remove the board from its outer box and anti-ESD bag, holding the board by the rear frame. 4. With the board upright, align the front (non-connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it into place firmly, and secure it with the retained screws. 5. If applicable, repeat steps 2 through 4 for any other output boards. 6. Power on the ISM 824. The new output board(s) is autodetected, and New ScanConverte takes approximately 30 seconds to initialize. The 16 character LCD Slot #2 14 display indicates the new board type, slot used, and counts down the initialization time. See inset for example display for a new ISM SC board installed in slot #2, with 14 seconds left. C 7. Following the image at right, connect output device cables to the BNC connectors to output RGsB, component, S-video or composite video signals. The output can be configured from the front panel or by SIS™ commands. The composite video output (the bottom BNC connector) is always active. R/R-Y G/Y R Right Balanced Stereo Output Tip NO GROUND HERE. Sleeve(s) Tip NO GROUND HERE. Left R Left L L Tip Ring Sleeve(s) Tip Ring Right Unbalanced Stereo Output G/Y Y Y B/ B-Y B/ B-Y VID 8. Insert a 5-pole captive screw connector into the local audio output connector for balanced or unbalanced stereo audio output. Wire the connector as shown below. C R/R-Y RGsB or Component Video VID S-Video C R/R-Y G/Y Y B/ B-Y VID Composite Video . CAUTION For unbalanced audio, connect the sleeve(s) to the center contact ground. DO NOT connect the sleeve(s) to the negative (-) contacts. 1 ISM SC Output Board Installation Notes, cont’d ISM SC configuration menu Using the front panel menu buttons (Menu and Next), the ISM SC board configuration menu can be accessed. From the Output Configuration screen, press Next until reaching the #x ScanConverter menu (see the image below). Press Menu and Next to navigate through the menus and use the front panel adjustment knobs ({ [), to change the settings as desired. For full menu details see the ISM 824 User’s Manual, online at www.extron.com. MENU NEXT From the default cycle press Menu repeatedly to reach the Output Configuration menu. Press Next (enters Select Output menu) and rotate either adjust knob to select the Scan Converter menu. Follow the figure below to enter each menu and use the Adjust knobs to change value as desired. ADJUST Select Output #x ScanConverter Menu Next Menu #x ScanConverter Input Setup Next Aspect Ratio 4:3 Rotate either encoder to select (4:3 or 16:9) Start Next #x ScanConverter User Presets Auto Image Input #x Off Rotate either encoder to select format Rotate either encoder to select a preset to save current settings Rotate encoder to select input and encoder to turn On or Off Rotate either encoder to select standard Next Next Next Erase Preset 1 2 3 Rotate either encoder to select a preset to erase Next Flicker Filter x Rotate either encoder to set a value Next Encoder Filter x Next V xxxx Next Next Save Preset 1 2 3 Phase xxxx Active #x ScanConverter Advanced Config Next Rotate to adjust Total Pix value and encoder to adjust Phase value H xxxx Menu Output Type YUV Output Standard NTSC V xxx Rotate encoder to adjust H start and to adjust V start Total Pix xxxx Menu Next Next H xxx #x ScanConverter Output Config Next Rotate to adjust H active value and encoder to adjust V active value Input Setup The Input Setup submenu allows configuration of aspect ratios. horizontal and vertical start points, total pixels and phase value, and the active horizontal and vertical area. Rotate one or both Adjust knobs as required to change values. Output Type The Output Type submenu displays and allows changing the format of the scan converted output. Use the Adjust knobs to select RGsB, low resolution component video (YUV), or S-video. Rotate either encoder to set a value Next Test Pattern None Rotate either encoder to select a test pattern Next Auto Memories Off Rotate either encoder to turn auto memories On or Off Next Next Full Screen Input #x Rotate to select input # and to turn full screen on or off Output Standard The Output Standard submenu displays and allows changes to the output standard. Use the Adjust knobs to select between NTSC, NTSC 0 IRE, and PAL. Flicker Filter The Flicker Filter reduces the flicker in the connected output display. When this submenu is active, rotate either Adjust knob to set the flicker filter value (0-3). 2 Encoder Filter The Encoder Filter maintains the sharpness of the connected output display. When this submenu is active, rotate either Adjust knob to set the encoder filter value (0-3). Test pattern The test pattern submenu offers the following test patterns to choose from: NTSC/PAL Color Bars Safe Area Crop 32x24 Crosshatch 4x4 Crosshatch Grayscale Ramp 1.33 Crop 1.78 Crop 1.85 Crop 2.35 Crop Full Screen The Full Screen submenu allows per-input setting of the displayed image on the output screen. When set to Off (default) the aspect ratio follows input resolution and the output image retains the input setting. When set to On, the aspect ratio follows the output resolution, and the displayed image always fills the screen. Board-specific SIS commands table Alternatively, the ISM SC board can be configured with specific SIS commands. The table below lists some of the ISM SC board-specific commands. For a full list of SIS commands refer to the ISM 824 User’s Manual, online at www.extron.com. Command ASCII command (host to switcher) Response (switcher to host) Additional description Video and audio Example X!*X@! OutX@•InX!•All] 4*2! Out2•In4•All] Video X!*X@& Example 5*2& OutX@•InX!•RGB] Out2•In5•RGB] Select video and audio input X! to output X@. Input 4 video and audio selected to output 2. Select video input X! to output X@. Audio X!*X@$ Example 5*2$ Input selection OutX@•InX!•Aud] Out7•In3•Aud] Input 5 video only selected to output 2. Select audio input X! to output X@. Input 3 audio only selected to output 7. Video output type Set video output type to X\ 36*X@*X\# X@TpoX\] Select video output format to X\ Where X\ = 0 = S-video, 1 = YUV, 2 = RGsB. View 36*X@# X\] View the video output format. SIS command table continues on page 4. N X! = Input number, 0-8 X@ = Output number, 0-8 3 ISM SC Output Board Installation Notes, cont’d Command ASCII command (host to switcher) Response (switcher to host) Additional description 37*X@*X\# X@Std X\] 37*X@# X\] Set video output standard to X\ Where X\ is: 0 = NTSC, 1 = NTSC 0 IRE, 2 = PAL. View the video output standard. Video output standard Set video output standard to X\ View Flicker filter N Command is case sensitive Set flicker filter level Increment value Decrement value View X@*X4$d X@DvzX4$] X@+d X@DvzX4$] Specify the flicker filter level to X4$. Increase the flicker filter level. X@-d X@DvzX4$] Decrease the flicker filter level. X@d X4$] View the flicker filter level. Set encoder filter level 24*X@*X4$# X@EncX4$] Set encoder filter level to X4$. Increment value Decrement value View 24*X@+# X@EncX4$] Increase the flicker filter level. 24*X@-# X@EncX4$] Decrease the flicker filter level. 24*X@# X4$] View the encoder filter level. On X@*X2) J TstX@*X2)] Select test pattern. View X@ J X2)] View the test pattern selection. Enable 99*X@*X!*1# X@FulX!*1] Disable 99*X@*X!*0# X@FulX!*0] Output full screen for selected input. Turn full screen off. View 99*X@*X!# X2(] View the current on/off status. Encoder filter Test pattern Full screen N X! = Input number, 0-8 X@ = Output number, 1-8 X2) = Test pattern, 00 = off, 01 = color bars, 02 = 32x24 crosshatch, 03 = 4x4 crosshatch, 04 = gray scale, 05 = ramp, 06 = safe area, 07 = crop, 08 = 1.33 crop, 09 = 1.78 crop, 10 = 1.85 crop, 11 = 2.35 crop X2( = Mode status, 1 = on, 0 = off X4$ = Filter value, 0-3 Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX 4 Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.4664 FAX Inside USA / Canada Only Inside Europe Only Inside Asia Only © 2009 Extron Electronics. All rights reserved. Inside China Only +86.21.3760.1568 +86.21.3760.1566 FAX 68-1123-61 Rev A 04 09