Issue 1 Touring Caravan Owners Handbook

Transcript

Touring Caravan OWNERS HANDBOOK Issue 1 CONTENTS WELCOME AND INTRODUCTION ... 1-1 Model Year .............................................................. 1-1 Elddis Group Technical Approvals ...................... 1-1 GENERAL SAFETY ................................ 2-1 Please read before using your new caravan. .. 2-1 Ventilation .............................................................. 2-2 High-Level Ventilation .......................................... 2-2 Low-Level Ventilation ........................................... 2-2 Ventilation in Separate Bedrooms ..................... 2-2 Gas Dispersal Holes ............................................ 2-2 Petrol/Diesel Fumes .............................................. 2-2 Fire Safety ............................................................... 2-2 Fire Extinguishers .................................................. 2-2 In Case Of Fire ...................................................... 2-2 Fire Retardant Foams .......................................... 2-2 PREPARING FOR THE ROAD .............. 3-1 Caravan Towing Vehicle Weight Ratio ............... 3-1 Nose Weight Indicator Jockey Wheel .............. 3-1 Loading .................................................................... 3-1 Internal Loading & Checks ................................. 3-1 External Loading & Checks ................................ 3-1 Pre-Tow Checklist & Hitch-Up ......................... 3-2 Winterhoff Stabiliser - Hitch Head Operation3-2 Activating the stabiliser ....................................... 3-2 Checking the stabiliser ........................................ 3-2 Uncoupling ............................................................. 3-3 Use of Your Caravans Breakaway Cable ......... 3-3 Correct Procedure For Use .............................. 3-3 Where a Designated Attachment Point Is Provided On The Tow Bar .......................... 3-3 Where No Designated Attachment Point Is Provided On The Tow Bar .......................... 3-4 Other Means of Attachment .............................. 3-4 When The Breakaway Cable Is Attached Check To Ensure ........................................... 3-4 Before Setting Off .................................................. 3-4 Handbrake .............................................................. 3-5 Cables ...................................................................... 3-5 TOWING AND DRIVING ..................... 4-1 Reversing ................................................................ 4-1 Speed Limits ........................................................... 4-1 Setting Off .............................................................. 4-1 Caravan Handling ................................................... 4-1 ARRIVING ON SITE .............................. 5-1 Check Site Regulations ........................................ 5-1 Selecting a Pitch .................................................... 5-1 Side-To-Side Levelling .......................................... 5-1 Leveller Jack ........................................................... 5-1 Ramp ........................................................................ 5-1 Front & Back Levelling ......................................... 5-1 Parking on a Reverse-Sloping Site or Steep Hill .................................................................... 5-1 GETTING STARTED ............................. 6-1 Electricity ................................................................ 6-1 Power Supply Charger ........................................ 6-1 12v Systems: .......................................................... 6-1 Generator/Charger ............................................... 6-1 Electricity Mains Supply ....................................... 6-1 Connecting To Mains Supply On Arrival at Site ................................................................... 6-1 Disconnecting Mains Supply When Leaving Site ................................................................... 6-2 Overseas Electrical Connection ......................... 6-2 Gas Supply .............................................................. 6-3 Connection ............................................................ 6-3 Changing a Gas Cylinder .................................... 6-3 Gas Regulator ........................................................ 6-3 High Pressure Gas Hoses ................................... 6-3 Water System ........................................................ 6-4 How to Use Your Aquasource ........................... 6-4 Connection to your water inlet ......................... 6-4 Draining Down Your Water System ................. 6-4 GAS SAFETY ADVICE ........................... 7-1 Facts about LPG .................................................... 7-1 Awning Spaces, LPG and Appliance Exhaust ... 7-1 LPG Gas System ................................................... 7-1 Gas Barbecue Point ............................................... 7-1 ELECTRICAL SYSTEM .......................... 8-1 12v Power Supply .................................................. 8-1 Battery Installation ................................................ 8-1 Battery Maintenance ............................................ 8-1 Generators / Charger ......................................... 8-1 230v Power Supply ................................................ 8-1 Mains Unit .............................................................. 8-1 Resetting the RCD ................................................ 8-1 Automatic Charging System ............................... 8-2 Maximum Bulb Ratings for Internal Lights ...... 8-2 Connecting a Solar Panel and/or Satellite Dish .................................... 8-2 Solar Panel Connection ...................................... 8-2 Satellite TC Connection ...................................... 8-2 12V Fuses - All Models ........................................ 8-3 HOW TO USE YOUR CARAVAN’S EQUIPMENT .................................... 9-1 Electrical Control Panel ...................................... 9-1 Cooking equipment .............................................. 9-2 Gas Hob ................................................................. 9-2 Gas Grill ................................................................. 9-2 Gas Oven ............................................................... 9-3 Refrigerator Model Thetford N112 LCD ....... 9-4 CONTENTS-1 CONTENTS Operating instructions ........................................ 9-4 Smart Energy Selection (SES) ............................ 9-4 Powering with electricity .................................... 9-5 Selecting electrical power manually ................. 9-5 Powering with gas .................................................. 9-5 Switching off the refrigerator ............................ 9-6 Securing products for driving ............................ 9-6 Door locking mechanism .................................... 9-6 Troubleshooting .................................................... 9-7 Maintenance ........................................................... 9-8 Water heater operation ..................................... 9-9 Gas operation ........................................................ 9-9 230V Operation .................................................... 9-9 Space Heater Operation ..................................... 9-9 Gas Operation ...................................................... 9-9 230V Operation .................................................... 9-9 Fan Operation ..................................................... 9-10 Microwave ............................................................ 9-10 Battery Charger .................................................. 9-11 Smoke Detector ................................................. 9-11 Thetford Cassette C-200 CWE Toilet ........... 9-12 Introduction ......................................................... 9-12 Features: ............................................................... 9-12 Preparing for use ................................................ 9-12 Emptying the waste holding tank .................... 9-12 Winterising/Storage ........................................... 9-15 Cold weather use ............................................... 9-15 High Altitude and hot weather use ................ 9-15 Cleaning and maintenance ................................ 9-15 Rooflights ............................................................. 9-16 The Omivent (12v) Rooflight ........................... 9-16 Toilet unit malfunctions ..................................... 9-16 The Heki 2 Rooflight ......................................... 9-16 Mini Heki Rooflight ............................................ 9-17 Seitz Window Opening ..................................... 9-17 Windows .............................................................. 9-17 Polyplastic Window Opening ........................... 9-17 Blinds & Flyscreens ............................................. 9-18 Flyscreens ............................................................. 9-18 Door Flyscreen ................................................... 9-18 Taps ........................................................................ 9-18 Exterior Door Retainers .................................. 9-19 Gas Locker Door ............................................... 9-19 Internal Doors .................................................... 9-19 Magnetic Catches ............................................... 9-20 Bed Make-up ........................................................ 9-20 L-Shape Lounge Double Bed ........................... 9-21 Bunk Beds ............................................................ 9-21 Removable Drawer Locker .............................. 9-22 TV Aerial ............................................................... 9-22 VHF Television Reception (Overseas only) ... 9-22 Entertainment System ....................................... 9-22 Radio/DVD ........................................................... 9-22 LCD TV ................................................................. 9-22 BPW Nose Weight Indicator Jockey Wheel . 9-23 Explorer Protect - Autowatch Alarm System 9-23 BPW Intelligent Drive Control (iDc) System 9-24 SECURITY ............................................. 10-1 Caravan Theft ...................................................... 10-1 Anti-Wind Corner Steadies ............................. 10-1 CRIS - The Caravan Registration and Identification Scheme - VIN ...................... 10-1 Window Etching & Chassis Marking .............. 10-2 Electronic Tagging ............................................... 10-2 CARE OF YOUR CARAVAN ............... 11-1 Exterior Cleaning ............................................... 11-1 Glass Fibre Reinforced Plastic (GRP) ............. 11-1 Acrylic Windows ................................................ 11-1 Care Instructions for Seitz Windows ............ 11-1 Care Instructions for Seitz Rooflights ........... 11-1 Window Blinds & Flyscreens ........................... 11-1 Winterisation/Storage ....................................... 11-1 ABS - A Frame Cover, Wheel Spats & Panels 11-1 Interior Walls ....................................................... 11-2 Furniture ............................................................... 11-2 Cooking Equipment ........................................... 11-2 Carpets, Upholstery and Curtains .................. 11-2 Shower Trays, Shower Room and Wash Basin Fittings ................................................ 11-2 Cleaning of all Taps ............................................. 11-2 Water Containers .............................................. 11-2 Water Systems - Sterilization .......................... 11-3 Truma Space Heater .......................................... 11-3 Thetford Toilet ..................................................... 11-3 Chassis Mounted Spare Wheel Carrier ......... 11-4 Tyres ...................................................................... 11-4 Pressures .............................................................. 11-4 Tyre Wear and Damage ..................................... 11-4 Changing a Wheel ............................................... 11-4 Jacking ................................................................... 11-5 Lubrication ........................................................... 11-5 Maintenance of your BPW Chassis ................ 11-6 Procurement of Spare Parts ............................. 11-6 STORAGE .............................................. 12-1 Long Term & Winter Storage ........................... 12-1 Caravan Covers .................................................. 12-1 Power Drain ........................................................ 12-1 WARRANTY ......................................... 13-1 3-Year Manufacturer’s Warranty ..................... 13-1 Parts Covered By This Warranty for Years 1 - 3 ............................................................... 13-1 CONTENTS-2 CONTENTS Specific Exclusions for Years 2 & 3 ................. 13-1 Conditions Attached to the Warranty: .......... 13-1 CODE OF PRACTICE - WATER INGRESS ......................................... 14-1 The Code ............................................................. 14-1 Conditions Attached To the Code .................. 14-1 Customer Obligation - Servicing .................... 14-1 Mains Electrics ..................................................... 14-1 Spare Parts ........................................................... 14-1 Remedial Work ................................................... 14-2 CARAVAN CONSTRUCTION MAIN COMPONENTS .................. 15-1 BPW Chassis ....................................................... 15-1 Braking System .................................................... 15-1 Body Shell ............................................................. 15-1 Windows .............................................................. 15-1 Insulation .............................................................. 15-1 Front Panel and Gas Bottle Locker Lid ......... 15-1 Awning Channel .................................................. 15-1 Additional Fixings to Your Caravan Shell ....... 15-1 Odyssey ................................................................ 16-1 ELECTRICAL DRAWINGS ................. 17-1 13 Pin Plug Wiring Diagram ............................. 17-1 Wiring Diagram - Odyssey ............................... 17-2 Road Lights - Odyssey ....................................... 17-3 TECHNICAL SPECIFICATIONS ........ 18-1 Elddis Odyssey .................................................... 18-1 GENERAL QUESTIONS ..................... 19-1 GLOSSARY ........................................... 20-1 SERVICE DOCUMENTS ..................... 21-1 INDEX ................................................... 22-1 CONTENTS-3 CONTENTS CONTENTS-4 INTRODUCTION Approved Retailers or Service Centres will be able to supply any replacement parts for your caravan, should the need arise, and in most cases any accessories you may require. WELCOME AND INTRODUCTION Congratulations on choosing an Elddis Touring Caravan. Please note: It is not possible to purchase replacement parts direct from Elddis. This Owner’s Handbook has been prepared for your guidance to help you derive the greatest amount of pleasure from the use of your caravan and your leisure time. We strongly recommend that you read this guide thoroughly so that you are fully aware of all the caravan’s features, equipment and systems. Changing market and supply situations may prevent us from maintaining the exact specification details in this guide and we therefore reserve the right to alter specifications as materials and conditions demand. Enjoy your new caravan Additional information and detailed appliance instruction manuals are also contained in your Owner’s Information Pack. Model Year All Touring caravans manufactured by the Elddis are designated by their model year. The 2009 model year runs from 1st September 2008 to 31st August 2009. Your new Elddis caravan has been designed as a recreational vehicle and is intended for recreational use only. It is not intended for business use or for permanent habitation. Elddis accepts no liability if the caravan is used for any purpose other than recreational/holiday use. Elddis Group Technical Approvals In order to ensure your new Caravan is safe to use Elddis are members of and have been inspected by the following bodies. Your caravan has been designed for towing behind a normal motor car. Additional care should be exercised when towing with a 4x4 because of the ‘off-road’ nature of the suspension. Owners should not tow their touring caravans with commercial vehicles (including light and heavy goods vehicles). When selecting a towing vehicle it is recommended that you consult the Caravan Towing Code, which is also included in your Owner’s Information Pack. National Caravan Council (NCC) who operated a certification scheme to ensure compliance with the European safety standards for caravans. National Inspection Council for Electrical Installation and Contracting (NICEIC) who carry out an annual inspection of Elddis electrical installations within caravans. Confederation of Gas Installers (CORGI) who carries out annual inspection to ensure that the gas installation installed by Elddis fully comply with all relevant regulations and standards. By following the instructions provided in this handbook and maintaining your caravan in a first class roadworthy condition, you are sure to have many years of carefree use. Elddis has also obtained ISO9001:2000 accreditation and this is audited by SGS UK Limited To ensure the very best quality and reliability all touring caravan designs and new developments are rigorously tested. Therefore Elddis will accept no liability or uphold the warranty if the caravan is altered or modified in such a way that would adversely affect the reliability. Please Note: It is a condition of your warranty that the caravan must have an “annual service” done by an Approved Retailer or Service Centre, and a record is kept. Pages are provided in the back of this guide, for your assistance. 1-1 INTRODUCTION 1-2 GENERAL SAFETY GENERAL SAFETY (ix) Never exceed your caravans Maximum Technical Permissible Laden Mass. (see Caravan Towing Vehicle Weight Ratio) (x) The laden nose weight for your caravan should not exceed the lower of the following: Please read before using your new caravan. In order for you to get the most out of your new Elddis caravan it is necessary for you to be aware of the following: (i) Do not obstruct ventilators and clean them regularly, it is advisable to clean and check all the ventilators annually for blockages and where necessary rectify any blockages found. (ii) Inspect the high pressure flexible gas hose (available from your retailer) regularly for deterioration and renew as necessary, with approved type, in any case no later than the expiry date stated on the hose. (iii) Turn off all gas appliances and turn off the gas supply before towing your caravan. (iv) Your caravan is fitted with a gas barbecue point which is not designed to allow gas flow into your caravan and should never be used for this purpose. (v) Never use portable cooking or heating equipment inside your caravan. Do not use your fitted cooking equipment as heating at any time. (vi) Never allow modification to your gas or electrical system unless qualified persons carry them out. All modification to the gas system should be carried out by a CORGI registered gas fitter. Any modifications carried out on the electrical system should be carried out by an electrician on the roll of the NICEIC or be a member of the ECA. (vii) (viii) • Towing vehicles maximum nose weight • Tow bar maximum nose weight • The caravan’s maximum nose weight which is 100kgs In the interest of safety, replacement parts for an appliance shall conform to the appliance manufacturer’s specifications and should be fitted by him or his authorised agent. (xi) Ensure heavy and large items are secured before towing your new caravan to reduce the risk of damage being caused while the caravan is in motion. (xii) When your caravan is connected to your towing vehicle it should be level or slightly nose down. An excessive nose down attitude or a nose up attitude could lead to instability when towing. (xiii) When your caravan is loaded to its MTPLM and the weight distributed in accordance with the towing code, your caravan is designed to be towed at a maximum speed of 130kmh/80mph. However, your attention is drawn to the fact that in the UK the maximum speed allowed for towing a caravan is 100kmh/ 60mph. (xiv) It is illegal to tow your caravan whilst it is occupied. (xv) If your caravan is fitted with a lift up bunk it is designed for a maximum weight of 11 stone and is not suitable for children under 3 years old without supervision. (xvi) Do not leave children under 14 years of age unattended in your caravan. IMPORTANT Your attention is drawn to the notice affixed in the caravan’s wardrobe advising on fire prevention, ventilation and what to do in case of fire. It is recommended that you provide a dry powder fire extinguisher complying with ISO 7165 of at least 1KG capacity by the exit door and a fire blanket next to the cooker. Ensure you read the ‘advice to occupier label’ fitted to your caravan usually found on the inside of the wardrobe door. 2-1 GENERAL SAFETY VENTILATION FIRE SAFETY All caravans manufactured by Elddis are ventilated at both high and low level in accordance with BSEN 721 Safety Ventilation. The fixed ventilation points fitted in your caravan must not be blocked under any circumstances as your safety may depend upon them. It is advisable that the fixed ventilation points are checked and cleaned (where necessary) on a regular basis. Fire Extinguishers High-Level Ventilation (i) Get everyone out of the caravan as quickly as possible using whichever exit is quickest including windows. Do not stop to collect any personal items. It is recommended that a 1 kg minimum capacity dry powder fire extinguisher be carried inside your caravan at all times. A fat pan fire must not have an extinguisher aimed at it, but must be smothered with a fire blanket. In Case Of Fire This is always provided by fixed ventilation within the fitted roof skylight. All roof skylights fitted by Elddis provide fixed free area ventilation. These roof skylights should be cleaned annually by use of a small brush to remove any dust that may have accumulated around the mesh fitted. On some roof skylights the mesh can be easily removed to aid cleaning. On fan-assisted roof skylights it is essential that the fan is switched off prior to cleaning. (ii) Raise the alarm. Call the fire brigade. (iii) Turn off gas container valve if safe to do so. Fire Retardant Foams Under the requirements of the Consumer Protection Act 1987, the manufacturer has a responsibility to ensure that their product is as safe as possible. With this in mind all caravans are equipped with either Combustion Modified High Resilient (C.M.H.R.) foam cushions or sprung mattresses. These foams are very much safer from a fire point of view than those previously used. In addition all upholstery is made of fire retardant fabric. Low-Level Ventilation Low-level ventilation is provided under the front chest of drawers, except in an L shape layout, where it can be found either in the nearside or offside bed box. The exact position can be identified via the white or black plastic cover used to prevent the ventilation from being obstructed. In order to clean the ventilator, remove the cover by undoing the two screws and clean using a small brush. It is essential that the cover is replaced once cleaning is complete. Ventilation in Separate Bedrooms In caravans with separated sleeping areas, separate ventilation is required and is provided via a roof skylight at high level and a ventilator at low level within a bed box. Gas Dispersal Holes All appliances and gas unions have a gas dispersal hole nearby. It is essential that these are not blocked or made ineffective. Petrol/Diesel Fumes The fitting of a tail pipe to your exhaust will reduce the possibility of fumes entering your caravan through the front fixed ventilation points. 2-2 PREPARING FOR THE ROAD Please note that this should only be used as a guide. For information on how to use the nose weight indicator please go to the section on ‘How To Use Your Caravan’s Equipment’. PREPARING FOR THE ROAD Before venturing out on to the road with your touring caravan, it is important that you prepare correctly. LOADING CARAVAN TOWING VEHICLE WEIGHT RATIO This ratio has a major influence on stability. It is recommended that: (i) The laden nose weight for your caravan should not exceed the lower of the following: * Towing vehicles maximum nose weight, * Tow bar maximum nose weight * The caravan’s maximum nose weight, which is 100kgs (ii) The actual laden weight of the caravan should always be kept as light as possible. The lighter it is whilst being towed on a road, the safer the outfit combination will be. (iii) The Caravan Club recommends a maximum caravan/towing vehicle weight ratio of 85% of the towing vehicle’s kerb weight providing both are properly maintained, fully serviceable and the other recommendations in this Handbook are followed. (iv) Whilst you can legally tow at a higher weight ratio than 85% (subject to manufacturers’ towing limits and driving license restrictions) towing a heavier caravan will increase the risk of instability, especially at higher speeds. (v) The greater the actual laden weight of the caravan in relation to the kerb weight of the towing vehicle the more careful and experienced the driver needs to be and the lower the speed at which instability could occur. Always lower and secure the jockey wheel and the four corner steadies (with the brace provided) before entering the caravan. This will ensure that the caravan does not tip up when you are inside. Please Note: Corner steadies should not be used as a jacking device. Internal Loading & Checks When loading your caravan it is advisable to: (i) Distribute items evenly over the axle and as low as possible to optimize road holding and achieve the best possible braking effect. (ii) Do not overload on one side as this will cause the caravan to lean and affect the road holding and stability. (iii) Do not stow tins, bottles or heavy items in overhead lockers when towing. (iv) Loose articles should be stowed securely to avoid movement and possible damage. (v) Ensure that all lockers and cupboard doors are closed and secured. (vi) Secure all bunks (if appropriate). (vii) Store the main dining table in its transit position. (viii) Set the refrigerator for 12V operation if any fresh food is stored in it and ensure the door is locked. (ix) Fully close and lock all windows and rooflights. Never tow with windows on night setting. WARNING: It is strongly recommended the loaded weight of the caravan does not exceed the kerb weight of the towing vehicle. (x) Leave all curtains and blinds open to prevent damage in transit. If your caravan has a rear window this may aid visibility. External Loading & Checks NOSE WEIGHT INDICATOR JOCKEY WHEEL The Jockey wheel nose weight indicator is fitted to all Elddis caravans. This can be used to give guidance on the actual nose weight your caravan is applying to your car’s tow ball. 3-1 (i) Gas cylinders should only be stored, correctly positioned, and secured in the gas bottle locker. The gas should be turned off. (ii) The leisure battery is stored and secured in the battery locker box, set into the tray provided and secured. PREPARING FOR THE ROAD (iii) Any external connections (battery chargers, connecting cables etc), should be disconnected and stowed. (iv) Check that all exterior locker doors are secure and locked. (v) Secure and lock the main caravan entrance door. PRE-TOW CHECKLIST & HITCH-UP Having loaded the touring caravan and secured the lockers and main entrance door: (i) (ii) Check touring caravan wheel bolts are torque tightened to the required level (See Index - Changing a Wheel). Fig 3-1 Activating the stabiliser Check tyre pressures (Refer to the Technical Specification section) and tyre condition for roadworthiness. The operating handle will not operate until the automatic closing function has been engaged. The handle can now be fully pushed down. The hitch will remain coupled with the stabiliser deactivated to facilitate easier manoeuvring. (iii) Ensure the jockey wheel is down, in good contact with the ground, clamp tightly secured, and the caravan handbrake is fully on. Checking the stabiliser (iv) Wind up the corner steadies. (v) With the caravan coupled to your towing vehicle and the stabiliser activated, the condition of the friction linings can be checked. The wear indicator (as shown in Fig 3.2) is within the top of the operating handle. The bar graph is marked with (+) and (-) symbols with (+) indicating good condition of the pads and (-) indicating that the pads should be checked. Reverse the car close up to the caravan’s hitch. It is advisable to seek assistance to guide you so that the car tow ball aligns with the caravan’s hitch. (Use of the caravan handbrake is advised. Extreme caution should be taken if manoeuvring the caravan down hill or on wet, slippery surfaces). (vi) Make sure the jockey wheel height is sufficient for the hitch head to clear the towing vehicles tow ball. (v) Manoeuvre the hitch head over the tow ball and lower the jockey wheel using the winding handle, until the hitch head opening sits comfortably over the tow bar ball. WINTERHOFF STABILISER - HITCH HEAD OPERATION Coupling The opened ball coupling is placed over the tow ball of the towing vehicle. As the coupling load is applied to the tow ball the coupling will automatically close, this is indicated when the security lugs become parallel on the side of the housing. (Fig 3.1) Fig 3-2 Disengaging the stabiliser Lift up the operating handle with care to release the sprung loaded stabiliser function. 3-2 PREPARING FOR THE ROAD Uncoupling the caravan’s brakes if it becomes separated from its towing vehicle. The cable assembly is designed to part, allowing the caravan to come to a halt away from the towing vehicle. Construction - Usually a thin steel cable, possibly plastic coated, and fitted with a means of attachment to connect to the towing vehicle. Operation - The cable should be able to pull tight to engage the caravan’s brakes without any hindrance to its action, if the main coupling of the caravan separates from the towing vehicle. It should never become taut during normal use. Correct Procedure For Use Fig 3-3 Before uncoupling disconnect the electrical connections and breakaway cable. Also check that it is safe to uncouple your caravan taking into account any gradients. With the stabiliser function disengaged, simultaneously pull back and lift the operating handle, this swings the securing lugs out of the locked position allowing the operating handle to be lifted into the fully open position. Before operating the jockey wheel, which will lift the caravan free of the tow ball, check that both caravan and towing vehicle handbrakes are applied! (i) Check cable assembly for damage. If in doubt contact your Retailer or Service Centre. (ii) Make sure the cable runs as straight as possible, and goes through a cable guide underneath the caravan coupling. (iii) Determine whether or not you have a designated attachment point (a feature of the tow bar which has been identified by the tow bar supplier as being for the attachment of a breakaway cable). Where a Designated Attachment Point Is Provided On The Tow Bar If the caravan is not to be used for any lengthy period of time we recommend the ball coupling is kept in the closed position. This can be done easily by pressing the safety ball into the ball space and slowly closing the operating lever. (i) Pass the cable through attachment point and clip it back on itself (Fig 3-4, Step 1); STEP 1 Please note: The WS3000 ball coupling can be locked in both the coupled and uncoupled condition with the ROBSTOP WS3000 hitch lock, however it is recommended that the Robstop is removed for towing. USE OF YOUR CARAVANS BREAKAWAY CABLE UK LAW requires that all caravans with brakes (e.g. caravans, horse boxes, car transporters etc), built on or after 1st October 1982, are fitted with a safety device to provide protection in the unlikely event of the separation of the main coupling while in motion. It’s also a legal requirement to use the breakaway cable whenever it’s provided. Fig 3-4 or The purpose of the breakaway cable is to apply 3-3 PREPARING FOR THE ROAD (ii) Attach the clip directly to the attachment point (Fig 3-5, Step 2). accessories e.g. a stabiliser, bumper shield, cycle carrier etc. (ii) STEP 2 That there must be sufficient slack in the cable to allow the towing vehicle and caravan to fully articulate without the cable ever becoming taut and applying the brakes. (iii) That it is not so slack that it can drag on the ground. Leave it too loose, and the cable may scrape along the ground, and be weakened so that it fails before doing its job! BEFORE SETTING OFF Fig 3-5 Note: this must be specifically permitted by the caravan manufacturer’s guidance, as the clip may not be sufficiently strong. Connect the 13 pin plug on the caravan Aframe to the towing vehicle. (ii) Check that all tail-lights, brake lights, road lights and indicators work correctly. (iii) Ensure that the correct vehicle license / registration plate is attached to the rear of the touring caravan. Where No Designated Attachment Point Is Provided On The Tow Bar (i) (i) Fixed Ball - Loop the cable around the neck of the tow ball. If you fit the cable like this use a single loop only (Fig 3-6, Step 3). (iv) Using the jockey wheel lift the tow ball slightly to check hitch is locked onto the ball (v) STEP 3 Wind up the jockey wheel until the wheel supports locate into the cut out sections at the base of the winding section. (vi) Raise and secure the jockey wheel using the clamp. The jockey wheel should be parallel to the direction of travel at all times. (vii) Check condition of and secure the breakaway cable to the tow vehicle. Fig 3-6 (ii) Detachable Ball - You must contact the tow bar supplier for advice. Other Means of Attachment Alternatively, it may be possible to attach the cable assembly to a permanent part of the tow bar structure with the approval of the tow bar supplier, or to an accessory sold for the purposes of breakaway cable attachment. When The Breakaway Cable Is Attached Check To Ensure (i) That the cable cannot snag in use on the caravan hitch, jockey wheel or any 3-4 PREPARING FOR THE ROAD HANDBRAKE Your caravan is fitted with BPW running gear and handbrake. It is essential that prior to towing you ensure that your handbrake is in the fully off position. This can be confirmed by ensuring that the handbrake arm is resting on the blue stop fitted to the side of the A frame as shown in Fig 3-7 below. Fig 3-7 CABLES For peace of mind, you may wish to check the ability of the cables to be able to cope with towing the vehicle at extreme angles before setting off. To do so position the vehicle at alternate extreme angles and check that the cables do not pull too tight, are liable to stretch or become unplugged. No cables should be allowed to touch the ground as they will wear and become damaged and ineffective. Please Note: If having followed this advice, you feel you cannot achieve a satisfactory cable arrangement, consult your caravan or tow bar supplier or service agent. 3-5 PREPARING FOR THE ROAD 3-6 TOWING AND DRIVING SPEED LIMITS TOWING AND DRIVING REVERSING It is advisable to have a second person available when reversing the caravan. • Normal road towing: 50mph • Motorways (including dual carriageways): 60mph SETTING OFF Start practising by choosing a left-hand bend for ease. Reverse slowly; turning the wheel, initially the opposite way to the direction you want the caravan to go. Now the front of the caravan is nudged out and is moving the rear in the intended direction. Take care not to hit the van with the car! Midways through the manoeuvre, when the caravan is correctly angled, reduce speed to a crawl and gradually apply opposite lock. Make the car follow the caravan round then finally straighten up. (i) Let the clutch in smoothly on the towing vehicle. Allow more engine speed to produce the power to move the additional weight of the caravan. (ii) Avoid wear and tear on the clutch and transmission by taking extra care not to ‘ride’ the clutch. (iii) Change gears smoothly. Try not to jerk the clutch. CARAVAN HANDLING Please Note: Proficiency at reversing can only be achieved with practice. (i) Allow for the caravan being wider than the car. Ensure you have a clear view to the rear. This may require the fitting of extended mirrors for towing your caravan. (ii) Do not bump the kerb with the caravan wheels. (iii) When passing other vehicles, allow more than the normal clearance for driving solo. (iv) Allow longer to obtain a fast enough speed to pass other vehicles. (v) Allow for the vehicle being twice its normal length. Do not suddenly swing out. (vi) Carry out all manoeuvres as smoothly as possible. (vii) Use the nearside wing mirror to check the caravan has clearly passed other road users when overtaking and changing lanes. (viii) Adverse weather conditions may affect the steering and braking characteristics of your caravan. Fig 4-1 4-1 TOWING AND DRIVING 4-2 ARRIVING ON SITE (ii) ARRIVING ON SITE CHECK SITE REGULATIONS Lower the jockey wheel to ground level before unhitching. (See index uncoupling) You should then park your car, usually next to the caravan furthest away from the door side. On arrival at a site, you should always check the site regulations. This will help avoid any unnecessary conflict with site management and other site users. Please Note: On upward facing pitches when the hydraulically damped drawbar of the hitch becomes fully extended, it will be necessary to compress the drawbar slightly in order to achieve a clean’ unhitching.With the caravan brake on, reverse the towing vehicle about 2.54cm (1") to release hitch lock tension and using the jockey wheel adjustment, unhitch the caravan as previously described. WARNING: Care has to be taken to prevent fouling when traversing ramps or other ground obstacles. SELECTING A PITCH Carefully select where you wish to place your caravan. The site should be as level as possible, preferably not under or near trees, well drained and away from possible boggy areas. Consider how you will move the caravan when it is time to leave the site. On sloping ground it is better to pitch facing downhill, especially during wet weather. FRONT & BACK LEVELLING This should be done only when the lateral levelling is complete. (i) Place the spirit level pointing front to back just inside the caravan door or on the A frame. (ii) Then raise or lower the jockey wheel until the caravan is horizontally level. Please Note: If there is a significant front to back slope, you may need to place a block under the jockey wheel. (iii) Next, wind down the corner steadies onto load spreaders (blocks of wood a minimum of 15.25cm (6") square or ‘Big Foot’ steady attachments) until they are firmly set against the ground. Please Note: It is possible on very uneven sites that when fully extended blocks may be required under the corner steadies to achieve this. It is important that the caravan is correctly levelled to ensure the correct working of the refrigerator, cooker etc. (iv) Now that your caravan is level, place the caravan step in front of the door ensuring that it is stable and safe to use. SIDE-TO-SIDE LEVELLING A quick glance at your pitch should tell you if you are likely to need side to side levelling i.e. levelling across the axle. On uneven ground lateral levelling is accomplished by the use of a leveller jack or ramp and a spirit level placed ‘across’ the caravan floor (not supplied). Leveller Jack Place the leveller jack, folded flat, in front of the wheel needed to be raised to level the axle. Tow the caravan onto the leveller jack and adjust the height until the spirit level shows that the caravan is laterally level. Ramp (i) Reverse onto your pitch about 30cm (12") further back than you wish to end up. (ii) Then place the levelling ramp in front of the wheel that needs to be raised. (iii) Place a spirit level parallel to the axle on the A-frame or just inside the caravan door. It helps to have two people at this point. One should drive the car very slowly forward moving the caravan wheel up the ramp, and the other should indicate when the spirit level bubble is in the middle. Whichever method you use, and once level: (i) Apply the caravan handbrake and chock the caravan wheel if necessary. PARKING ON A REVERSE-SLOPING SITE OR STEEP HILL For successful parking on a reverse slope or steep hill, the operator need only apply the handbrake with one hand while gently but purposely inching the caravan a small distance backwards with the other. CAUTION Never enter the caravan without first lowering the four corner steadies with the 5-1 ARRIVING ON SITE brace provided. Corner steadies should not be used as a jack.Take care not to lift the caravan wheels. 5-2 GETTING STARTED AC or DC and whether it is at the correct voltage and frequency. GETTING STARTED You have arrived at your destination and now want to start to enjoy your new Elddis caravan. The following is a step by step guide to connecting your services and getting everything in your caravan working. (ii) Your caravan is properly earthed. Never accept a supply from a socket outlet or plug having only two pins, or from a lighting outlet. (iii) Any residual current device (earth leakage circuit breaker) in the mains supply to the caravan has been tested within the last month. In case of doubt, consult the site owner or their agent. ELECTRICITY Power Supply Charger Your caravan is fitted with a power supply/ charger. This will charge the caravan battery when fitted and also power the 12V systems in your caravan. (iv) Make sure that the switch at the site supply point is off and that all electrical equipment in the caravan is switched off by ensuring your caravan mains isolating switch on the MCB is in the ‘OFF’ position. It is recommended that you always carry a leisure battery. The Charger is fully automatic and will not overcharge the leisure battery. ELECTRICAL WARNING Attention: Always disconnect the electrical connector between the towing vehicle and the caravan before connecting a mains electric supply to the caravan and before charging the caravan battery by any other means. 12v Systems: Your caravan is fitted with an automatic system for selection of power. When connected to the 230V site supply the automatic Power Supply/Charger will charge the leisure battery and the 12V systems. Once the above checks have been made: When connected to the car (always disconnect 230V supply), the system automatically switches to the car supply. (v) When the ignition is switched on the 12V system in the caravan is automatically switched off, car power is supplied to the refrigerator and battery charging is in operation. Remove any cover to the electricity inlet provided on the caravan, and insert the female connector of the flexible orange supply cable as shown. GENERATOR/CHARGER When connecting to a generator, always switch off the RCD, start the generator and allow running for a few minutes to stabilize. When this has happened, switch the RCD to the ON position. ELECTRICITY MAINS SUPPLY Your caravan’s main electrical installation is designed to run on 230V at 50 hertz AC supply. (vi) Locate the site supply and remove any cover from the socket outlet provided at the supply point. Insert the male plug at the other end of the flexible orange supply cable. Switch on the main switch at the site supply point (if appropriate). CONNECTING TO MAINS SUPPLY ON ARRIVAL AT SITE Before connecting the caravan installation to the mains supply, check that: (i) The mains supply is suitable for your installation and appliances, i.e. whether it is 6-1 GETTING STARTED WIRING OF CONNECTING CABLE AND CARAVAN MAINS INLET WARNING: It is essential that connections are made exactly as shown. If terminal markings are not in accordance with the above diagram they must be ignored. OVERSEAS ELECTRICAL CONNECTION (vii) Place any surplus cable under the caravan. Ensure that the surplus cable is not coiled up as it could overheat. (viii) The MCB main electricity supply switch should be put in the ‘ON’ position. (ix) Check the RCD is working by pressing the test button. Once pressed all electrical lights and appliances should cease to operate. Reset, and then check the electrical system is operational. (x) Finally in order to get your 12V system operational, ensure the master 12V switch is in the ‘ON’ position. Refer to index for further details on the control panel fitted. Please Note: Connection to a mains voltage supply OVERSEAS requires particular attention. Care must be taken when connecting supplies abroad since the supplies can be of REVERSE POLARITY. The significance of REVERSE POLARITY is that when equipment is switched off, it may not be electrically isolated. The only certain way of making equipment safe is to unplug it. A means of checking the polarity of the mains supply when overseas is recommended. There are available several proprietary makes of equipment for the purpose. DISCONNECTING MAINS SUPPLY WHEN LEAVING SITE (i) Switch ‘OFF’ at the caravan mains isolating switch. (ii) Remove the male plug from the site supply. (iii) Disconnect the female plug from the caravan and store the cable in an appropriate locker. If it can be achieved, it is preferable to connect live to live, and neutral to neutral to maintain full electrical protection. CHECK all caravan equipment is set-up to accept the site supply before actually switching on. 6-2 GETTING STARTED Gas Regulator GAS SUPPLY Your caravan is designed to operate using either propane or butane liquefied petroleum gas at 30M/bar. Gas can be obtained from your caravan dealer. Your caravan is designed to accept a maximum 2 x 6kg Truma gas bottles. Connection Make sure that heating and cooking appliances and gas cylinders are switched off. Each gas appliance is connected to its own gas isolation tap under the cooker. These are identified on the tap via a label. Below is a key to identify each label. To operate the tap the arrow on the tap shows the direction of flow for the gas. The arrow should be pointing towards the appliance for the appliance to operate. There will be a small label next to the bank of taps under the cooker, which is also reproduced below: Your new Elddis caravan has been fitted with a fully approved gas regulator designed to operate at a gas pressure of 30Mbar.Your regulator is fitted with a test point, which is accessed via the inlet at the side of the regulator. This access point is only for carrying out gas pressure tests and should not be used for any other purpose. CAUTION It is strongly recommended that only CORGI approved gas fitters carry out any work on your caravan gas installation. High Pressure Gas Hoses Water Heater Cooking Appliance Space Heater Hob Refrigerator Gas On/Off You should only connect to this regulator using a length of approved high-pressure hose not exceeding 450mm from the gas cylinder to the regulator. These approved high-pressure hoses are available from your Elddis Retailer. These hoses are connected using screw thread fittings, which will make a seal if connected and tightened using a spanner. Once the hose is securely connected turn on the gas tap above the regulator, then turn on the gas bottle to allow gas to flow into the caravan. In order to make all your caravan gas appliances operational it is necessary to open each appliance gas tap as detailed in previous column. All your gas appliances should now be operational. Instructions on how to use each appliance are detailed later in your handbook. Changing a Gas Cylinder Before commencing to change a gas cylinder ensure that the valve on the cylinder is turned fully off. Turn off all gas operated appliances. Remove the gas hose from gas cylinder. WARNING: Aerosols and highly flammable liquids must not be stored in the compartment behind, or adjacent to, any gas appliance. Some industrial LPG appliances operate at high pressure and require a ‘high pressure’ regulator.This often has an adjusting handle on it. NEVER use such a regulator on a caravan. Before refitting a gas cylinder, ensure that all gas operated appliances are turned off - particularly after winterisation. Ensure all connections are secure. WARNING: If cylinders other than those recommended are used, ensure that the cylinders are adequately supported, do not block ventilation openings and cannot cause damage to fixtures and fittings located in the compartment. Ventilation holes must be clear at all times. 6-3 GETTING STARTED WATER SYSTEM How to Use Your Aquasource Your new Elddis Caravan is fitted with the Whale Aquasmart water system incorporating the Smartflo pressure pump to provide a reliable, high rate for superior showering. To achieve the best performance from the Smartflo pump please follow the priming instructions below. CAUTION Do not under any circumstances connect your caravan to the mains water supply without the pressure reducer fitted. Damage will occur to the caravan’s water system! Max. working inlet pressure: 7 bar. Static pressure: approx. 0.8 - 1 bar When the system is first used or if air is sucked into the system when emptying your water container: • Insert plug into wall socket and close lid to lock plug in place. • Place carbon filter which is fitted to the hose into the water container. • Switch on the 12V supply to pump. • Open the farthest away hot water tap from the pump. • When the water is flowing smoothly close hot tap and open the cold tap to expel the remaining air. • Repeat points 4 and 5 for the second farthest away tap from the pump, until the closest tap if finally purged of air. Connection to your water inlet (i) Uncoil the hose and screw tap adaptor to the drinking water stand pipe and plug in the hose adaptor. (ii) Raise the lid; clean both the water socket and the Aquasource plug. Push the plug into the socket. Turn on the mains water supply and check for leaks. Open one of the taps and purge any air that may be trapped in the water system. To remove, pull the lower trigger and pull out the hose plug. Draining Down Your Water System Note: Following these instructions will maximise the performance of your pump. Ensure all your taps are in the off position and the pump is turned off, and then connect your external water container to the water inlet using the connection hose supplied. Switch the pump switch on the control panel to on and the red light should illuminate. The pump will run until the correct pressure has built up in the system. Once the pump switches off your water system is ready to use. Please note, it will take at least 30 minutes for your water heater to heat the water in its holding tank to the expected temperature. When you open a tap the pump light should illuminate and the pump run while the tap is open, the pump may run for a short time after the tap is closed in order to build up the correct working pressure again. (i) It is essential that you drain down your caravan water system when it is not in use. This is most important during winter months to protect against frost damage. (ii) Disconnect the water pump and switch off power supply. (iii) Remove the water heater fuse from the switch spur and store in a safe place. (iv) Open the safety drain valve on the water heater located next to the water heater. (v) Open all taps and remove all plugs from sinks and showers. Lever operated taps should have the lever put into the up and central position. (vi) Open the drain outlets on the outside of your caravan. (vii) Adjust the level of the caravan to ensure that the drain outlet is at the lowest point of the caravan. This will aid the flow of water to ensure all water is drained off. (viii) After 30 minutes level the caravan and prepare it for storage if necessary. 6-4 GAS SAFETY ADVICE will get hot when in use.You are advised not to use any additional gas appliances outside your caravan unless it is a Gas Barbecue connected via the Barbecue point supplied with your caravan. GAS SAFETY ADVICE In the event of a suspected gas leak the gas must be turned off using the isolation valve on the gas bottle. A competent gas fitter should then check the system before it is used/reused. Please ensure that you have read the operating instructions for each gas appliance contained in your Owners Information Pack. Please ensure that any gas hose left unconnected is protected from dirt or other foreign bodies entering the hose. Regularly check flexible gas hose, joints and connections for tightness. Finally, make sure that each gas appliance is working efficiently to the recommendations of the appliance manufacturers. GAS BARBECUE POINT See Index - Ventilation Your caravan is fitted with a gas barbecue point. The gas barbecue point, when fitted, is situated on the nearside towards the front. This point is for use with a gas barbecue only. Simply lift up the flap, unplug the red plastic end cap and connect the appliance in accordance with the gas barbecue manufacturer’s instructions. FACTS ABOUT LPG • LPG is not poisonous. • Bi-products are harmless. • LPG is dangerous if all air and oxygen is excluded. • LPG has been given a smell by the manufacturers in order to identify leaks. • The gas is heavier than air and therefore sinks to the lowest point. CAUTION: Do not use a gas barbecue inside the awning. ALWAYS use the appliance in the open air. There will be an isolation valve fitted next to the Barbecue point. This is an automatic valve, which cannot be operated unless a connection has been made to the Barbecue point. Do not apply any force to this value. AWNING SPACES, LPG AND APPLIANCE EXHAUST There is no danger of pollution of an enclosed awning space from the LPG exhaust from a refrigerator venting into it. Space heaters may produce sufficient exhaust to pollute the awning space, if it is totally enclosed, from a general comfort, smell and hygiene point of view. In extreme cases there could be a build up of carbon dioxide to a dangerous level. Caravan owners are advised to allow some fresh air circulation in the awning space when such appliances are in use. WARNINGS • Fresh air circulation should be allowed below the caravan when appliances are in use and when flues terminate below the floor to allow free evacuation of the products of combustion. At least three sides of the underfloor space should always be kept open and unobstructed especially by snow. Do not make any additional openings in the floor. • Outlet sockets located within the caravan should only be used with a dedicated appliance and not an independent unit. • No appliance shall be used outside when connected to an internal outlet. • Maintain adequate spacing of combustible materials from sources of heat. • Do not use additional independent gas appliances inside the caravan. Please Note: Ventilation holes must be clear at all times. LPG GAS SYSTEM Elddis does not recommend the use of any external cylinders. All cylinders in use should be within the gas locker provided. If you wish to utilise a larger cylinder and have this outside the gas locker then the connecting hose must not exceed 750mm. It is recommended that no flammable material is stored or placed within 300mm of any open flame.Your attention is also drawn to the fact that the surface of the Space Heater in your caravan 7-1 GAS SAFETY ADVICE 7-2 ELECTRICAL SYSTEM For normal operation all switches on the unit need to be in the ON position. The switches on the left of the unit are known as MCB’s (miniature circuit breakers). These take the place of the conventional fuse but are more convenient. In the event of a fault the MCB ‘trips’ i.e. automatically moves to the OFF position. After elimination of the fault the MCB can be re-set by switching to the ON position (against the spring pressure in an upwards direction). If an earth fault develops, or a person was to touch a live piece of equipment, the leakage of current to earth should immediately operate the RCD (residual current device) and ‘trip’ the main switch, to the OFF position. This switch can only be re-set after elimination of the fault. ELECTRICAL SYSTEM 12v POWER SUPPLY Battery Installation Your caravan will be fitted with a BCA Leisure charging and power distribution unit. If you wish to install a leisure battery please ensure that it is placed on the battery tray supplied with your caravan. Then place the tray in the battery locker fitted to the side of your caravan. Connect the battery to the clamp fittings connected to the connection leads within the battery box. Elddis recommends that you use sealed for life leisure batteries of a minimum rating off 40 ampere-hours at 20 hours discharge rate. Please Note: In case of difficulty, consult an approved electrical installation contractor (who may be the local electricity board). It is dangerous to attempt modifications and additions yourself. Lamp holder-plugs (bayonet- cap adaptors) should not be used under any circumstances. Battery Maintenance Your leisure battery should be maintained in accordance with the manufacturer’s instructions. For information on the automatic charging system in your caravan please refer to ‘Automatic Charging System’ in the index. Resetting the RCD Do not charge your leisure battery with any charger other than that supplied. Failure to comply may cause damage to your battery. If you remove your leisure battery, ensure that it is not placed on a cold surface as the battery will deteriorate more rapidly than if stored at a suitable temperature To re-set, operate the switch as for MCB’s. Periodically, the RCD should be checked by operating the test button marked ‘T’. The unit should immediately switch to the OFF position. If the unit does not switch off then a qualified electrician should be consulted. If the unit does switch off, the test is complete and the switch can be re-set restoring the supply back to normal. Generators / Charger Please Note: Simultaneous operation of all of the 230V mains electrical equipment may not be possible. A typical UK caravan site mains hook-up point provides a maximum output of 10 amps and on some continental sites the available output may be as low as 5 amps. If your loading exceeds the site supply it may trip the site circuit breaker. Please check the available mains output with your site operator. The following items need to be added together if used simultaneously. All electrical equipment fitted in your new caravan can be run from either a controlled generator or charger whose output is maintained between 11volts and 14volts. At least once every 3 years, the caravan electrical installation should be inspected and tested, and a report on its condition obtained, as prescribed in British Standard BS7671. 230v POWER SUPPLY 230V mains equipment typical consumption figures: • Refrigerator ............................................ 0.50 amps • Charger .................................................... 0.50 amps • Water heater ............................................ 3.9 amps • Blown air heaters .................................... 8.5 amps • Colour TV ............................................... 2.50 amps • Microwave ............................................... 4.00 amps Mains Unit The Mains Unit replaces the conventional fuse box. Similar, but larger ones are often fitted in new houses. The unit, normally located in the wardrobe, gives overloads and earth leakage protection for the 230V electrical supply in your caravan. 8-1 ELECTRICAL SYSTEM AUTOMATIC CHARGING SYSTEM The battery charger will operate automatically when the caravan is connected to the mains outlet on a caravan site. The 12V system, with the exception of the 12V refrigerator and battery charging, will not operate when the caravan is connected to the towing vehicle. CHECK all caravan equipment is set-up to accept the site supply before actually switching on. MAXIMUM BULB RATINGS FOR INTERNAL LIGHTS Type of Light Maximum Bulb Rating Compact Fluorescent ......................................... 9W Reading Lights .................................................... 10W Downlighters ...................................................... 10W Dinette soffet lights ........................................... 20W Bedroom lights ................................................... 10W Please Note: Ensure that you only replace a blown bulb with one of the same rating. Never replace a bulb with one with a higher rating.You should ensure that when fitted, no bulb is in contact with the surface of the lamp or shade. Connecting a Solar Panel and/or Satellite Dish If you ordered your caravan with the entertainment pack option fitted then your caravan will have both a solar panel connection point and a satellite TV connection point within the battery box. Solar Panel Connection To connect a solar panel insert the panel connection lead into the connection point within the battery box, please ensure that you have a regulator in line whenever a solar panel is connected. Satellite TC Connection To connect a Satellite TV receiver simply insert the satellite connection into the connection point within the battery box and this will feed the satellite signal to the TV outlets within your caravan. You will need to fit the satellite decoder between the aerial outlet and your TV. 8-2 ELECTRICAL SYSTEM 12V FUSES - ALL MODELS 8-3 ELECTRICAL SYSTEM MAINS UNIT 8-4 HOW TO USE YOUR CARAVAN’S EQUIPMENT Please Note: Before attempting to use any electrical appliance ensure that you have connected the mains connection cable to a mains hook up and that the mains isolation switch is in the ‘on’ position. HOW TO USE YOUR CARAVAN’S EQUIPMENT Congratulations on your purchase of a new Elddis caravan. Within this section of your caravan’s handbook we will give you brief details on how to operate all of the caravan’s equipment from the gas cooking equipment to the widow blinds. For further details on the major equipment within your caravan please read the individual appliance instructions contained with your user information pack. ELECTRICAL CONTROL PANEL Odyssey Your new Odyssey Caravan will be fitted with the control panel shown below Please Note: Before attempting to use any gas equipment please ensure that the gas bottle is connected securely to the caravan’s regulator via a high pressure gas hose and the bottle valve is in the ‘on’ position. Also ensure the appliance isolation valves are in the ‘on’ position as shown in the gas system section. Control panel for caravans without a fixed water tank. (i) To operate the 12V systems for your caravan depress the left rocker switch. (ii) (iii) (iv) (v) To operate the pump for your water system depress switch marked with a tap symbol. When the pump is running the neon light will illuminate. When the left hand button is depressed the available battery Voltage will be displayed. The right hand button has no function on this control panel. 9-1 HOW TO USE YOUR CARAVAN’S EQUIPMENT COOKING EQUIPMENT Gas Grill WARNINGS (i) Turn the grill control knob to the high flame position and with the knob depressed press the electronic ignitor button. If the grill does not light within 20 seconds then turn off the grill control knob for at least 30 seconds before trying again. (i) All pans should be mounted centrally over the burners, even when cooling, to protect adjacent walls. (ii) Do not lower the glass cover until hob has cooled down. (iii) Glass lids may shatter when heated. Turn off all burners and grill before shutting the lid.The glass cover should be raised when operating the grill. (iv) Accessible parts may be hot when the grill and oven are in use.Young children should be kept away. (v) Do not use grill or oven as a space heater. (vi) When you are cooking it is essential to provide additional ventilation, such as opening windows near grill, cooker and oven. (ii) Once the grill lights it will be necessary to keep the grill control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated enough to operate. Gas Hob (i) Turn the individual control knob for the burner you wish to light. (ii) If the hob is fitted with electronic ignition then depress the ignition button, which can be found on the front of the oven next to the oven control, while depressing the control knob. The depressing of the control knob overrides the flame failure device fitted to the burner. If the burner fails to light within 20 seconds then release the control knob and wait 30 seconds before trying again. (iii) Once the burner lights it will be necessary to keep the control knob depressed for about 5 to 10 seconds to ensure that the flame failure device is heated up enough to operate. Grill control knob Burner controls Ignitor button 9-2 HOW TO USE YOUR CARAVAN’S EQUIPMENT Gas Oven (i) Turn the gas oven control knob to maximum then depress the knob while pressing the electronic ignitor button. If the oven does not light within 20 seconds turn off the control knob and wait for 30 seconds before trying again. (ii) Once the oven is lit it will be necessary to keep the control knob depressed for 5 to 10 seconds to ensure the flame failure device is heated up enough to operate. Oven control knob 9-3 HOW TO USE YOUR CARAVAN’S EQUIPMENT REFRIGERATOR MODEL THETFORD N112 LCD A = Main switch (on/off) D = Function LED B = Mode selection switch E = LCD display C = Cooling level selection switch OPERATING INSTRUCTIONS If an energy source becomes available that has a higher priority than the source the refrigerator is currently using (e.g. if your vehicle engine is started), the system will stop using the current energy source and switch to the energy source with the higher priority. When the caravan is on tow, the refrigerator should only be operated electrically, i.e. from the 12V battery in the towing vehicle and not by means of the bottled gas. The refrigerator can be run on 230V or LP gas whilst stationary. If a fault occurs in one or more of the possible energy sources, the system will not generate an error message while an alternative energy source is still available. The SES system switches over automatically. CAUTION: Only use one source of energy at a time. WARNING: The refrigerator should not be operated on LP gas whilst being towed or when on a petrol station forecourt. Note: If none of the energy sources are available, the blue LED flashes every second and an error code is shown in the display. Switching on the refrigerator • Clean the inside of the refrigerator before you switch it on. Automatic models additionally allow you to select the desired energy source manually. • Let the refrigerator run for at least eight hours before you place food in it for the first time. Important: The memory of the SES system saves every change made to the setting. Consequently, the SES system will start up on each subsequent occasion in the last-selected setting. SMART ENERGY SELECTION (SES) When you start up the refrigerator (equipped with Smart Energy Selection (SES)) you should usually select the AUTO mode. The SES system will then automatically select the best of the three available energy sources. The system will apply the following priority: - mains voltage (230V) - direct current (12V) - liquid gas 9-4 1. Open the valve of the gas bottle. 2. Open the taps of the gas supply. 3. Press main switch (A). The function LED will turn blue and all symbols on the LCD display will light up. 4. Use the mode selection switch to select the "Auto" function or one of the power supplies that you want. The LCD display will show the option you have selected. 5. Set the desired refrigerating cooling level by HOW TO USE YOUR CARAVAN’S EQUIPMENT means of the cooling level selection switch (C). The LCD display will show the cooling level setting you have selected. Direct current (12V): The SES system will select 12V powering only if a mains voltage (230V) is unavailable, the vehicle engine is running and a voltage higher than 11V is available. If a fault occurs during electrical powering (230V or 12V), an error message will not be shown on the display as long as another energy source is available. The system will automatically switch to the available energy source that has the highest priority. A. Use the main switch to switch the refrigerator on and off. The function LED will turn blue. The display LCD shows the most recent settings. After 10 seconds the LCD display's backlight will go out. The function LED remains blue. B. Press the mode selector switch and the LCD display backlight will show the setting for 10 seconds. Pressing the mode selector switch successive times takes you through the menu in the following sequence: AUTO, manual DC (12V), manual gas, manual mains voltage (230V) and back to AUTO. Select either the AUTO option or one of the other power supplies that you want to use. The LCD display shows the option you have selected. If you select the AUTO option, the system will choose the most suitable power supply and the AUTO symbol and the symbol of the power supply chosen by the system will both be shown on the LCD display. Ten seconds after release of the mode selector switch, the system will switch off the LCD backlight. Selecting electrical power manually Mains voltage (230V): The LED warns you whenever insufficient voltage is available or if a fault occurs. If this happens, the LED will start flashing once per second and an error code is shown in the LCD display. When sufficient current is available again, or the fault has been resolved, the LED will emit a steady blue light again. Direct current (12V): The LED warns you whenever your vehicle's engine is not running, or if a fault occurs, or if sufficient voltage is available. If this happens, the LED will start flashing once per second and an error code is shown in the LCD display. Once the engine is running, or the fault has been resolved, or sufficient voltage is available again, the LED will again emit a steady blue light. C. Use the cooling level selector switch to control the temperature of the refrigerator. When you press the cooling level selector switch, the LCD backlight will light up and show the currently set temperature. Every time you press the cooling level selector switch again, you set the refrigerator one position cooler. On reaching the coldest temperature, the system will start again at the warmest temperature setting. Ten seconds after release of the cooling level selector switch, the system will switch off the LCD backlight. NB: If the refrigerator has been manually set to operate at 12V, it will not automatically switch to another energy source when your vehicle's engine is not running. In this case, the refrigerator will stop cooling. POWERING WITH GAS Powering with gas can be selected both by the Auto mode (only Automatic fridges) and manually. Auto mode POWERING WITH ELECTRICITY The system will select gas operation if mains voltage (230V) is unavailable; or the vehicle's engine is not running. Powering with electricity can be selected both by the Auto mode (only Automatic fridges) and manually. Once mains voltage (230V) is available again or the vehicle's engine is running, the system will switch to the available energy source that has the highest priority if the fridge is in Auto mode. Auto mode Mains voltage (230V): This energy source will be selected if the mains voltage is greater than 200V. This power supply requires a continuous current of 12V to operate the electronic control system. If the refrigerator switches from 12V DC to gas operation when it is in auto mode, the system will wait for about 15 minutes before igniting the 9-5 HOW TO USE YOUR CARAVAN’S EQUIPMENT gas. During this time, however, the gas indicator lamp will come on. The delay is built in to avoid it switching to gas operation whenever you stop to refuel your vehicle. You can cancel the delay by immediately switching the refrigerator off and then on again. system consists of a simple click-and-slide plastic strip. To secure products on the rack while driving, push the plastic strip as tightly as you can against the products on the rack. In the storage space on the inside of the refrigerator door, there is the unique Thetford flexible bottle slide. The slide prevents bottles from sliding around during driving. Push the slide against the products in the door or place the products between the bottle slide. If the system selects gas operation, the ignition will be activated automatically. The gas will flow to the burner and be lit by the electric ignition. If the flame goes out, the gas will immediately be lit again. Door locking mechanism Selecting gas operation manually The refrigerator door has an automatic locking If the flame cannot be lit within 30 seconds, the gas supply will stop and gas mode will be switched off. The LED will start flashing every second and an error code is shown in the LCD display. The gas mode can be reset only if the refrigerator is switched off. If you switch the refrigerator on again and the gas mode is still not working, the LED of the manual gas mode will flash to indicate that gas is unavailable and an error code is shown in the LCD display. Switching off the refrigerator Push the main switch (A). The blue LED will go out. The refrigerator is now completely switched off. mechanism. The door locks automatically when you press it shut firmly. The lock releases unnoticed when you open the refrigerator with your hand. This automatic locking mechanism also keeps the refrigerator door shut during driving. For some models an additional security device is fitted below the refrigerator. By pushing the locking bar over the pin when the door is closed, you can make doubly sure that the door does not come open during your journey. Use the special storage latch on the door locking mechanism to fixate the open door. This prevents unpleasant odours and mould in the refrigerator. Securing products for driving One of the racks in your refrigerator has a system for securing products during driving. The 9-6 HOW TO USE YOUR CARAVAN’S EQUIPMENT TROUBLESHOOTING Before calling the authorised Service Department please check whether: • The instructions in the section “Using the refrigerator” have been followed. • The refrigerator is not tilted excessively. • It is possible to operate the refrigerator with an available power source. Failure: The refrigerator does not work in gas operation mode. a) Gas bottle empty. a) Change gas bottle. b) Is the supply cut-out device open? b) Open the cut-out device. c) Air in the gas pipe? c) Switch device off and on again 3-4 times to remove air from the gas pipe. Failure: The refrigerator does not work on 12V. Possible cause Action you can take a) On-board fuse defective. a) Fit new fuse. b) On-board battery discharged. b) Check battery, charge it. c) Engine not running. c) Start engine. Failure: The refrigerator does not work on 230V. Possible cause Action you can take a) On-board fuse defective. a) Fit new fuse. b) No connection to supply voltage. b) Establish power connection. c) AES: gas operation despite connection to the supply voltage? c) Appliance switches to gas operation due to insufficient supply voltage (automatically switches back to 230V operation). Failure: The refrigerator does not cool sufficiently. Possible cause Action you can take a) Inadequate ventilation to the unit. a) Check that the ventilation grilles are not covered. b) The thermostat setting is too low. b) Turn the thermostat to a higher setting. c) There is too much ice on the condenser. c) Check that the refrigerator door seals when shut. d) Too much warm food put inside. d) Let food cool down first. e) Appliance running for a short time. e) Wait several hours, check again. 9-7 HOW TO USE YOUR CARAVAN’S EQUIPMENT MAINTENANCE • Works on gas components and electrical installation may only be carried out by authorised personnel. We recommend to contact your Dometic Service Centre. • EN 1949 stipulates that the appliance’s gas equipment and its associated fume system must be inspected after installation and a certificate issued. Afterwards a qualified technician must inspect according to EN 1949 every two years and a certificate issued. It is the user’s responsibility to arrange for inspections after purchase. • It is recommended that the gas burner be inspected and cleaned as necessary at least once a year. We recommend maintenance following an extended shutdown of the vehicle. 9-8 HOW TO USE YOUR CARAVAN’S EQUIPMENT WATER HEATER OPERATION SPACE HEATER OPERATION Gas operation Gas Operation Gas Control Ultrastore Control (i) Turn the gas control on top of the heater to the desired setting and depress the knob. (i) Ensure that the water heater has been filled with water and that the outside flue cover has been removed. (ii) Using the Ultrastore control knob, turn the dial to the desired temperature setting then turn the outer ring to the flame position. (ii) Keeping the control knob depressed look into the viewing window and see if the gas ignites. You should be able to hear it ticking until the pilot light ignites. (iii) Once the Ultrastore is switched on a green light is visible within the switch and the unit will now try and ignite. (iii) Once the pilot light is lit keep the control knob depressed for a further 20 seconds to allow the thermocouple to operate. (iv) If within approximately 10 seconds, the Ultrastore fails to ignite then a red failure light will also appear. If this happens wait 30 seconds before trying again. (iv) If the heater fails to ignite please wait 20 seconds before trying again. 230V Operation 230V Operation (i) Simply depress the Electrical switch fitted next to the gas control to the 230V position. This will turn on the water heaters electrical element. It is imperative that there is water in the heater whenever the Gas or Electric is switched on. Ultraheat Control (i) Simply depress the main switch on the Ultraheat control panel to the 230V position. (ii) Then set the power rating you require on the panel at either 500w 1000w or 2000w. 9-9 HOW TO USE YOUR CARAVAN’S EQUIPMENT Fan Operation MICROWAVE The blown air function of the space heater is controlled by the three position switch on top of the heater. Note: Your microwave is connected to your 230V electricity supply via a non customer useable plug. Fan Control (i) Position 0 is off (ii) Position A operates the fan in automatic mode. In this position the fan will only run when there is sufficient heat to require the air to be circulated. (iii) The third Position will operate the fan at all times. (iv) The speed of the fan is controlled by the number position set with 5 being the fastest speed and 1 being the lowest. Controls: • Time + Button increases the duration of operation. WARNING:The space heater surfaces become hot in use and the guard provided does not give full protection to the young or elderly. • Time - Button decreases the duration of operation. • Power button sets the power level for the microwave. • Stop button can be used to stop the microwave before the full time set has elapsed. • Start button sets the microwave working for the time set. 9-10 HOW TO USE YOUR CARAVAN’S EQUIPMENT BATTERY CHARGER The battery charger for the caravan battery will automatically switch on when the caravan is connected to a mains supply. The battery charger will also provide a 12V supply to the caravan when a battery is not connected. Please note that the battery charger fitted is designed to keep your battery charged and is not designed for charging up a flat battery. SMOKE DETECTOR The caravan smoke detector will become active once the 9V battery which should be supplied with the smoke detector is connected. The smoke detector fitted to your caravan has an alarm pause mode which will reduce the sensitivity of the alarm for a short period to allow for cooking within the caravan. The alarm pause mode is activated by pressing the button marked HUSH on the smoke detector. While the detector is in the pause mode the detector will beep once per minute to alert that the alarm pause mode is activated. 9-11 HOW TO USE YOUR CARAVAN’S EQUIPMENT THETFORD CASSETTE C-200 CWE TOILET Preparing for use Following is a brief illustrated step by step guide. For more detailed information please refer to manufacturers literature. Introduction The Thetford Cassette C-200 CWE is functional and incorporates modern styling with home like features. The unit is an integral part of the motorhome bathroom. CAUTION (step 4): Warmer weather or longer intervals between emptying the waste tank may require additional toilet fluid. Use only Thetford toilet fluid to achieve the best results. Never add toilet fluid directly into the toilet bowl. The Thetford Cassette C-200 CWE is constructed of high quality plastics for durability and has a high gloss finish that is easy to clean and maintain. The unit consists of two sections, a permanently installed toilet system and a slide out waste holding tank - the Cassette. CAUTION (step 14): Do not depress air release valve button until pour out spout is facing downwards. The toilet section includes a rotatable bowl, a removable seat, and a control unit with a flush button and a waste level warning device. The valve blade handle is located under the bowl. The cassette capacity is approx. 17 litres and the tank should be emptied when the waste-level warning device comes on. This will occur when the tank contains more than 15 litres of waste. The cassette is located underneath the toilet and is removed for emptying from the outside of the vehicle through an access door. A rotating pourout spout, automatic holding tank vent, air release valve, valve blade, carrying handles and hand grips are incorporated into the cassette. A sliding cover guarantees optimum hygiene. Note: After the warning device comes on, the capacity remaining is equal to approximately 5 uses. Emptying the waste holding tank CAUTION: Do not allow the waste cassette to become overfilled. See trouble shooting section for emergency emptying procedure. Note: Some vehicles are equipped with water pumps supplying high water pressure, which can result in having an over flushing problem. It is possible to use the flow restrictor supplied with the toilet (packed together with the instruction manual) by installing it in the water tube at the connection level. Features: • • • • • • • • • • • • • • Removable seat and cover. Rotatable bowl. Valve blade handle: opens and closes valve blade manually. Flush button: activates flush. Waste level indicator: indicates when cassette requires emptying. Rotating pour-out spout: makes emptying cassette easy and convenient. Automatic cassette vent: vents the cassette when inserted in the toilet. This prevents over pressure in the cassette. Upper-carrying handles: makes carrying and emptying easy. Sliding cover: opens and closes automatically when sliding the cassette in and out. Guarantees optimal hygiene. Valve blade and blade seal. Vent button: vents the cassette to avoid splashing while emptying. Handgrip. Valve blade opener. Access door. Locks from outside the motorhome. Rinse the holding tank with clean water. Prepare the cassette for use again by following steps 1 to 6. Replace the holding tank and lock the access door. 9-12 HOW TO USE YOUR CARAVAN’S EQUIPMENT 4 - Remove dosage cap and pour-out spout. Add toilet fluid in the dosage cup. Add approx. 2L of water through spout to cover tank bottom. Replace cap, return pour-out spout to original stored position. 1 - Open access door and pull retaining clips upward. 2 - Remove cassette by pulling straight out. When cassette hits stop, tilt downwards 5 - Slide the holding tank into position through access door. Never force insertion as this can cause damage to the toilet. 3 - Position tank vertically and swivel pour-out spout upwards. 6 - Make sure the retaining clip secures the holding tank. Close and lock the access door. 9-13 HOW TO USE YOUR CARAVAN’S EQUIPMENT 10 - After use, open the blade, by pushing the blade handle in an anticlockwise direction and press the flush button. 7 - Open water fill door and add 50ml. of Aqua Rinse.Then fill the tank with fresh water using a jerry can or hose. Tank capacity is 7 litres. 11 - After flushing, close the blade by pushing the blade handle clockwise.The toilet may also be used with the valve blade open, which allows the waste to pass directly into the holding tank. 8 - Turn the bowl into the most comfortable position, when necessary. 9 - Before using the toilet, we recommend to add some water to the bowl by pressing the flush button. Release button to stop. 12 - Open access door and remove holding tank.The holding tank can only be removed when valve blade is closed. 9-14 HOW TO USE YOUR CARAVAN’S EQUIPMENT Winterising/Storage The Thetford Cassette C-200 CWE is easily winterised for storage. If the toilet is connected to a separate water tank, drain the tank. When the motorhome water tank is empty, press the flush button until the water stops flowing. Empty the cassette. If the toilet is connected to a central water tank, open the electric valve by pushing the flush button while draining the water supply system of the motorhome. Empty the cassette. Leave the blade of the cassette open. Do not replace cap on spout, this helps to keep the cassette dry. 13 - Carry the holding tank to a normal household toilet or authorised disposal point. Place holding tank in vertical position and rotate pour-out spout upwards. Cold weather use The cassette can be used in cold weather when the motorhome is heated. When the vehicle is not heated for more than a day (or a night), winterise the cassette. High Altitude and hot weather use Changes in altitude during driving, and large temperature variations give no problems as long as the cassette is inserted into the toilet. The automatic cassette vent will depressurise that tank when there is over or under pressure. High temperatures may require additional Thetford toilet fluid. 14 - Remove measuring cap. Grasp unit by upper carrying handle nearest pourout spout. Place other hand on upper rear hand grip so that the vent button can be depressed with thumb while emptying.This ensures a smooth outflow of tank contents. Cleaning and maintenance To clean the seal and blade, the use of Thetford bathroom cleaner and rinse with water is recommended. Alternatively, use a luke warm solution of diluted washing up liquid. Do not use household cleaners as they may damage the seals and other toilet parts. Dry the seal and blade thoroughly and spray economically with silicone spray, alternatively use olive oil. Do not use Vaseline or other vegetable oil products. The toilet bowl, seat, cover and the exterior of the toilet unit and cassette can be cleaned with a mild detergent/water mixture. 15 - Once the pump has been cleared of water place appropriate size container under the drain plug. Empty any remaining water from the fresh water tank by taking out the drain plug. Clean the seals and lubricate them where appropriate after drying. 9-15 HOW TO USE YOUR CARAVAN’S EQUIPMENT Toilet unit malfunctions built-in fixed ventilation when closed. It operates as an extractor fan and air intake fan. Contact your dealer or a Thetford Service Centre. Please note: Do not change the direction of the fan unless it has been switched off ‘O’ position and the blades have stopped rotating. We advise draining the fresh water tank prior to travelling. Antifreeze should not be required if the motor home is heated. If you do wish to use antifreeze, brands containing the following properties may be used in the fresh water tank: • Ethylene glycol • Mono-Ethylene glycol • Propane-diol • Glycerol • Ethane-diol • Glycol The Heki 2 Rooflight To open to the tilted position: (i) Press the knob in the toggle catches on either side of the rooflight and turn through approx. 90°. (ii) Grasp the metal bar in the middle, snap it out of its holder, swivel down and press the rooflight upwards. (The rooflight is held by the two gas springs after approx. 150mm). (iii) Swivel the metal bar towards the rooflight and snap into its holder. Never use alcohol based antifreeze, i.e. Methanol, Ethanol, and Iso-propanol. ROOFLIGHTS (iv) To close the rooflight, proceed with steps (iiii) in reverse order. Your caravan is fitted with at least one type of the following roof lights. To open in the intermediate position: (i) Open the toggle catches on either side of the rooflight. The Omivent (12v) Rooflight (ii) Grasp the metal bar in the middle; snap it out of its holder, swivel down and press the rooflight outwards. (Rooflight is opened automatically after approx. 150mm by the two gas springs.) (iii) Open both fasteners and swivel the metal strap toward the intermediate position and pull the rooflight down until the metal strap is stopped by the fasteners. (iv) To close, proceed with steps (i-iii) in reverse order. To open in the ventilation position: (i) Open the toggle catches on either side of the rooflight. (ii) Using both hands on the two toggle catches, press the rooflight up about 2cm and fasten the toggle catches in the corresponding setting. (iii) To close, proceed with steps (i-ii) in reverse order. Closing the blinds: The Omivent is a double-glazed roof light constructed from a synthetic ultra-violet screened material. Its side-operating mechanism allows a completely free central opening with (i) Take hold of the end rod (without rocker) in the recessed grip and engage in the opposite end rod (with rocker). 9-16 HOW TO USE YOUR CARAVAN’S EQUIPMENT (ii) Select the required position (blackout/ flyscreen) by moving both joined end rods together. WINDOWS Your caravan will be fitted with either Polyplastic; Seitz framed windows, or a mixture of both. CAUTION: In extremely bright sunshine, the blackout blind must only be closed two-thirds, and the rooflight must be set in the continuous airing position. Polyplastic Window Opening (i) In order to open the Polyplastic window it is only necessary to move the catch upwards and release the catch from the backing plate. Opening the Blinds: (ii) The Polyplastic window should remain in the open position once opened, however if it does not then tighten the friction control on the window stays to increase the holding force. (i) Move blind (end rod with rocker) right to the outside. (ii) Hold the recessed grip with one hand; with the other hand, press the rocker and move the blind back (do not let it recoil). (iii) The Polyplastic window is also fitted with a night ventilation position where the catch is set to the centre position on the backing plate; in this position it may be possible for rain to enter the caravan in adverse conditions. CAUTION • Do not stand on the acrylic rooflight. • Close HEKI 2 completely before moving off. • Do not leave your caravan when HEKI 2 is open. • Please consult your supplying dealer if you have any problems or defects. • Remove any snow/ice or dirt before opening the roof. • Do not open when it rains or when there is a strong wind. Seitz Window Opening (i) In order to open the Seitz window you must depress the button on the catch before moving the catch. Failure to do so will lead to the catch breaking. (ii) Seitz windows will automatically stay open once open due to the built in ratchet within the stay. Mini Heki Rooflight (i) To open, push the large central button. (iii) In order to close the window it is necessary to open the window fully then close the window in one steady movement before closing the stays when the button should click into the locked position. (ii) Whilst depressed, slide the bar to the desired position and locate into the stops provided. The Mini Heki roof light will generally be fitted in washroom areas. Keep button pushed in, then turn handle 9-17 HOW TO USE YOUR CARAVAN’S EQUIPMENT BLINDS & FLYSCREENS TAPS Blinds All the taps are operated by lifting the lever and turning the lever right for cold and left for hot water. In order for the taps to work, the pump switch on the control panel needs to be in the ON position. For caravans with fixed water tanks the taps need to be in the TAPS position. (i) Pull blind down by its centre catch. Do not pull down by one side of the blind. This will inevitably lead to problems. (ii) Do not allow blinds to spring back freely. Always control them by hand. WARNING: The water temperature could be very high so do not lift the lever with the tap turned to the full left position. Flyscreens (i) To operate the flyscreen, either pull the screen fully down, fully up or across, dependant on type of window fitted, and clip into place on the blind/frame. (ii) To release, unclip from the blind/frame. If a cross bar is fitted, gently pull the crossbar downwards towards you and allow the tension of the spring to roll up the flyscreen. (iii) Where a crossbar is not fitted, disconnect from the blind catch and release gently. (iv) It is recommended that blinds are not in the closed position whilst the caravan is moving. Kitchen Tap Door Flyscreen The exterior door flyscreen can be opened or closed from inside or outside the caravan and does not restrict door openings. When opening or closing the door flyscreen use the finger grip provided. Bathroom Tap Shower Mixer Tap 9-18 HOW TO USE YOUR CARAVAN’S EQUIPMENT EXTERIOR DOOR RETAINERS INTERNAL DOORS The door retainer fitted to your Elddis caravan is operated by simply lightly pushing the door to the side of the caravan. The retainer should automatically engage and hold the door in place. To release the door simply pull the lever located on the side of the retainer towards the door and the retainer will release the door enabling it to be closed. Toilet/Shower Room Doors Toilet/shower room doors are fitted with a lever lock, which is operated by pushing the lever down. The lever is spring-loaded and will return to the closed position upon release. It is recommend that the lever is always used when closing the door. Toilet/Shower Room Doors OTHER INTERNAL DOORS Other internal doors such as the wardrobe and table storage locker are fitted with a 2-position button lock. Push the button to lock the door and the button should remain flush with the door. Push the button again to release and the button should then protrude from the door surface. GAS LOCKER DOOR All caravan models are fitted with a gas strut supported door which will remain in the open position without the need for a holding bracket. This door will remain open unless locked by the key. Please Note: It is important when raising your gas locker door that you do not push the door past the vertical position as this could damage the hinges. Also care should be taken when leaving the door in the open position to ensure that any wind cannot catch the door and push it open beyond the vertical position. Other Internal Doors 9-19 HOW TO USE YOUR CARAVAN’S EQUIPMENT MAGNETIC CATCHES BED MAKE-UP Magnetic catches work on contact with the metal plate on the rear of the door. Simply close the door until the magnet engages and holds the metal plate. Pulling the door towards you with a moderate force will be sufficient to disengage the magnetic catch and open the door. Parallel Lounge 1 SPRUNG HINGES 2 3 Overhead lockers will use sprung hinges. These are suitably strong enough when closed to securely retain the door and prevent it from opening in transit. Pulling the handle towards you with moderate force is sufficient to open the locker door and hold it in the open position. SLIDING DOORS 4 The room divider should be held in place during transit by the use of the strap with the stud fastening. When stationary, the room divider can be held shut by contact between a metal plate and magnet. 5 The two single beds can be easily converted into a double bed by pulling out the bed slats, stored beneath the chest of drawers or stored in the bed slat box at the front/end of the caravan. Arrange seat cushions appropriately. 9-20 HOW TO USE YOUR CARAVAN’S EQUIPMENT L-Shape Lounge Double Bed Bunk Beds 1 1 2 2 3 3 4 4 On L-shaped layout, the bed frame is pulled out from underneath the rear facing seat. Arrange the seat cushions appropriately. Removal of sofa back rest cushions will provide single beds. All high level beds will take a maximum weight of 75kgs / 11 stone. When in use, the high level beds must have the bunk safety boards in place as shown in the diagram. Touring caravans are manufactured with a lightweight construction and therefore the beds are not designed to be knelt, sat or stood upon without all the bed cushions in place. 9-21 HOW TO USE YOUR CARAVAN’S EQUIPMENT REMOVABLE DRAWER LOCKER (ii) Loosen the mast locking collar and wall bracket and raise the antenna. Turn the mast to direct the antenna towards the TV transmitter. The RED SPOT on the bottom of the mast indicates the front of the antenna. To remove from the caravan, first locate the two retaining straps at the bottom rear of the unit, the straps are released by pulling away and down this releases the thumb catches. The locker can now be removed for storage. (iii) When receiving vertically polarised signals. Rotate the winder anti-clockwise to cant the antenna through 90 degrees. Do not over tighten or use undue force on the winder. DO NOT cant for vertically polarised signals with the TELESCOPICS EXTENDED. (iv) Switch on the power pack and the red LED will illuminate. To secure the unit into the caravan, first place the locker into position, then feed the straps though the thumb locks, holding the strap taut push the thumb lock so that is closes on the strap. (v) Check the gain control switch is set to normal “NML” for use. (vi) Tune your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. TV AERIAL (vii) Secure by tightning the mast locking collar and wall bracket. VHF Television Reception (Overseas only) (i) Extend the two telescopic antennas. (ii) Tune your television into the strongest signal. You may need to adjust the direction of the mast to achieve the best picture quality. (iii) For fine tuning of VHF you may also need to adjust the length of the telescopic antennas. Please Note: VHF TV transmissions are only horizontally polarised. ENTERTAINMENT SYSTEM Radio/DVD If you ordered the entertainment option with your new caravan then details on how to set up and use the Radio/DVD will be contained in your document wallet. Status 530 Directional Antenna LCD TV Your new Elddis caravan will be fitted with a 530 Status TV aerial If you have ordered an LCD TV with your new caravan then details on how to set up your TV will be supplied with the TV. To operate your 530 Directional TV aerial follow the procedure outlined below: (i) Firstly determine the approximate location of the nearest transmitter and whether the signals are horizontally or vertically polarised. For assistance ask your park operator or check other antennas in the vicinity. 9-22 HOW TO USE YOUR CARAVAN’S EQUIPMENT BPW NOSE WEIGHT INDICATOR JOCKEY WHEEL EXPLORER PROTECT - AUTOWATCH ALARM SYSTEM The indicator, which is an integral part of the jockey wheel, will give an estimate of the noseweight of the caravan. The Explorer Protect system is fitted as standard on the Odyssey range. Manufactured by Autowatch, The Explorer Protect system is designed to give years of trouble free operation. Made with only the highest quality components and using state of the art technology you can be assured that your caravan has the best electronic protection available. The measured value, maximum 125 kg, corresponds approximately to the supporting load of the ball coupling. For a measurement please ensure that: (i) The caravan is standing on horizontal ground. Each caravan alarm is installed with a Passive Infrared Detector (PIR), a wireless sensor that detects movement in the caravan and transmits a radio signal to the alarm module. If the alarm is on the siren will sound. A leg sensor, fully sealed against dust and water, will detect if the corner stabilising leg is being raised or lowered and transmits a coded radio signal to the alarm. (ii) The caravan is standing horizontally, corresponding to a distance between the lower edge of the ball coupling and the ground of approx. 390 - 420 mm. (iii) The jockey wheel is only extended up to 70 mm. (iv) The wheel of the jockey wheel is showing to the rear of the caravan. Additional sensors can be purchased from your retailer to enhance security. See section below for operation or consult the manufacturers instructions provided in the Owners Information Pack. Basic Operation Arming the System (i) Briefly press (large) arm/disarm button. (ii) Single chirp. (iii) Awning light illuminates for 30 seconds. (iv) Settling time of 15 seconds before responding to triggers. (v) Single intermittent flash of status LED (every 2 seconds). (vi) All sensors triggered will result in siren sounding for 30 seconds, or until reset by pressing the arm/disarm button. Disarming the System (i) Briefly press the (large) arm/disarm button. (ii) Double chirp. (iii) Awning light illuminates briefly on and off and then on again for 30 seconds. (iv) LED off. Panic Alarm (i) Press and hold the small panic button on the transmitter for two seconds. (ii) The siren will sound for thirty seconds, unless reset by pressing any of the transmitter buttons. 9-23 HOW TO USE YOUR CARAVAN’S EQUIPMENT Emergency Disarm Arming the System in Test Or Buzz Mode Insert the touch-key briefly into the socket. The alarm will turn off. In the buzz mode the siren will sound a short tone when a sensor is triggered instead of sounding for 30 seconds. It is advisable to test all the sensors. Silent Arm and Disarm (i) Press the small button briefly followed by a press on the arm/disarm button. BPW INTELLIGENT DRIVE CONTROL (IDC) SYSTEM (ii) The alarm will arm/disarm without chirps. If you have ordered your caravan with the safety and security pack it will be fitted with the BPW iDC system and here are some simple instructions on how it operates. Sensors Each caravan alarm is installed with a Passive Infrared Detector (PIR) and a leg sensor. Additional sensors can be purchased from your dealer to enhance security. (i) The sensors of the iDC system continually measure the lateral accelerations of the caravans axle(s). Passive Infra Red Sensor (ii) The iDC system immediately detects any risk of snaking and automatically and gently applies the caravan brakes. The gentle braking pulls the caravan back on track. The wireless PIR sensor will detect movement in the caravan and transmit a radio signal to the alarm module, if the alarm is on the siren will sound. (iii) iDC makes caravan maintenance easier by detecting slack in the braking system. Leg Sensor The leg sensor will detect the corner stabilising leg being raised or lowered and transmit a radio signal to the alarm. The leg sensor is fully sealed against dust and water and has a battery life expectancy of three years. When the battery becomes exhausted, the sensor will need to be replaced. (iv) In the event of a power failure the iDC fails safe so that it automatically returns to the starting position and the service brake is released and remains fully functional. For full operating instructions please read the iDC document supplied within your document wallet. Enhanced Features Arming The System In “At Home” Mode In the ‘at home’ mode, any sensor that is programmed to be isolated, such as the PIR sensor will not trigger the alarm. Other sensors, such as the leg sensor, will trigger the siren. Arm as normal followed by a second press on the arm/disarm button within 2 seconds. Normal “on” tone followed by “at home” tone indicating isolation is active. Settling time of 15 seconds before responding to triggers. Armed in the isolation mode will be indicated by a double flash intermittently of the LED. The “at home” sensors will be isolated; other sensors will trigger the siren for 30 seconds. 9-24 SECURITY CRIS - THE CARAVAN REGISTRATION AND IDENTIFICATION SCHEME - VIN SECURITY Theft deterrent, prevention and security of your touring caravan is taken very seriously at Elddis. That is why we have provided a combination of standard features and optional extras designed to deter and prevent thieves from stealing your property. And in the unlikely event that they should succeed, aid the identification, speedy recovery of your property and assist in the prosecution of the thief. CriS is the national register of UK manufactured touring caravans and was established by the National Caravan Council (NCC) in conjunction with HPI Ltd. All Elddis caravans are recorded on the CriS database by their unique 17 digit Vehicle Identity Number (VIN). This VIN and the caravan description are recorded on the Touring Caravan Registration Document, which is sent by CriS to the caravan’s registered keeper. Caravan Theft The theft of a caravan can occur in the most unlikely circumstances; from a motorway service area, even from an owner’s driveway. Secure all windows and doors when your caravan is unoccupied, even if only for a short length of time. Make a separate note of the number to keep safe at home. CriS issues Touring Caravan Registration Documents which are the equivalent of the log books issued by the DVLA for cars - the Touring Caravan Registration Document confirms the name of the registered keeper, the VIN and full vehicle description. ANTI-WIND CORNER STEADIES Shortly after purchasing this caravan you should receive your Touring Caravan Registration Document. It will be sent by post to your home address. The rear corner steadies on all Elddis caravans have a special cowling that allows for the precise positioning of a security bolt. Once the corner steadies are down, the bolt is put in place and padlocked. This prevents the potential thief from being able to lift the corner steadies making it extremely difficult to tow the vehicle away. Owners are advised to purchase good quality, extended loop padlocks in order to secure them. 10-1 SECURITY WINDOW ETCHING & CHASSIS MARKING ADDITIONAL SECURITY Consider fitting any device which might deter or prevent intrusion by thieves. For example: A wheel lock will prevent towing of the caravan and removal of the wheel. FREE CRIME PREVENTION advice about securing your caravan, protecting your valuables, property marking, either at home or whilst on site, can be obtained from the Crime Prevention Officer through your local Police Station. The VIN number is stamped onto the chassis of the touring caravan and etched onto all of the windows acting as a further deterrent.Your Touring Caravan Registration Document will include a 17 character VIN (Vehicle Identification Number), shown in the top right -hand corner. This 17 character VIN will be die- stamped into the caravan drawbar and chemically etched on up to a maximum of 10 eye level windows. To protect yourself and your touring caravan, never leave the Registration Document in the caravan. For security reasons keep it in a safe place. If you sell the caravan please follow the instructions on the Touring Caravan Registration Document. Please Note: If you do not receive a Touring Caravan Registration Document, lose it, or any of the details recorded are incorrect, please contact: CRIS - Dolphin House, New Street, Salisbury, Wiltshire, SP1 2TB. Telephone: 01722 411430 Spare windows stencils can be found in your owners information pack for use if you ever need to order a replacement window. ELECTRONIC TAGGING In conjunction with the CriS registration scheme, all Elddis touring caravans are electronically tagged during manufacture for added security and ease vehicle identification. The security tag containing the individual identity of your caravan is concealed within the caravan body and can only be read by using a special decoder. Please Note: Your Local Police Can Obtain The Use Of A Decoder By Contacting C.R.I.S. on Telephone No. 01722 411430 10-2 CARE OF YOUR CARAVAN Please Note: Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the window again using only cold water and dry off with chamois leather. CARE OF YOUR CARAVAN This section of the guide is devoted to the care, cleaning and general preservation of your caravan in order to retain its showroom condition. EXTERIOR CLEANING Please Note: Should scratches appear on the acrylic windows these can often be removed with an acrylic polish, i.e. ICI Perspex polish. Gentle polishing with a liquid metal polish, i.e. Brasso may also have the desired effect - consult your retailer BEFORE attempting to remove any but the slightest scratch. Under no circumstances should an abrasive or harsh cleaner be used. Do not use a pressure wash as this can disturb mastic seals. Exterior painted body parts of the caravan (usually the side walls) are acrylic finished aluminium, which is extremely durable and easy to clean. It is recommended you first wash off any heavy dirt and mud with cold water then use a proprietary brand wash and wax shampoo and rinse with plenty of cold water. CARE INSTRUCTIONS FOR SEITZ WINDOWS Use soap suds and plenty of water or Seitz special cleaning agents to wash the acrylic window. Use talcum powder to care for the rubber seals. Only use water and mild soap suds to clean the blinds. Caution:The use of a pressure wash on your caravan is not recommended as it can lead to water entering the caravan via any of the external vents and could disturb the seals. Please Note: Do not keep the blinds closed for long periods of time, as this can result in material fatigue. GLASS FIBRE REINFORCED PLASTIC (GRP) GRP components need to be washed, waxed and taken care of like a car. Chemicals and dirt can collect during storage, and the gel coat can be stained or marked when chemicals combine with rain or dew. Most stains or marks can be removed with mild dishwashing detergent, but more stubborn marks may require a (fine grit) rubbing compound such as T-cut. CARE INSTRUCTIONS FOR SEITZ ROOFLIGHTS Clean the acrylic rooflight with soap suds and plenty of water, or use the Seitz special cleaner. Use talcum to care for the rubber seals. Only use water and mild soap suds to clean the blinds. To help keep your GRP components looking almost like new, it is wise to wash the parts monthly (or more frequently) using mild dishwashing detergent, but avoid using strong alkaline (e.g. trisodium phosphate) or acidic cleaners or abrasives. Waxing the components once or twice a year with a good grade paste wax will help to maintain the colour and finish. Please Note: The 12-month guarantee becomes null and void if these instructions are not followed. WINDOW BLINDS & FLYSCREENS To clean the blinds and flyscreens, moisten a soft cloth or sponge with a small amount of water and mild soap suds and gently wipe dirt off. Allow to dry before retracting, failure to due this could result in mildew forming. ACRYLIC WINDOWS Your caravan is fitted with shatter resistant acrylic windows. To preserve their clarity and unblemished transparency it is essential that the following cleaning instructions are strictly adhered to: Road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water do not use a sponge to clean off heavy dirt deposits. Any remaining dirt should be washed off using a soft cloth and warm water. Winterisation/Storage Please Note: The blind/flyscreen should not be left in the down position when the caravan is not in use or throughout the winter as the memory of the mechanism may be lost. ABS - A FRAME COVER, WHEEL SPATS & PANELS To preserve the appearance of all ABS panels and 11-1 CARE OF YOUR CARAVAN fittings road grit, dust, sand, flies, lime tree secretions, bird droppings etc., should be washed off using plenty of cold water. Any remaining dirt should be washed off using a soft cloth and warm water. Under NO circumstances should any abrasive cleaning agents, household detergents or proprietary cleaning fluids be used. Wash the ABS material again using only cold water and dry off WATER CONTAINERS (i) All water remaining in any water container should be disposed of so that the container is empty. (ii) The outside of external water containers should be thoroughly cleansed and washed down to remove any dirt, dust or other contaminant. Water at a suitably hot temperature containing an appropriate detergent is recommended for this purpose. Water should then be put into the container, swirled round, then emptied out. INTERIOR WALLS Your caravan interior walls will only require a wipe over with a damp cloth, using a mild detergent, to keep them in a ‘showroom’ condition. (iii) All containers should then be totally filled with water containing an appropriate disinfectant / sterilizing solution and allowed to stand for the recommended contact time (e.g. Milton for 15 minutes). FURNITURE Treat your caravan furniture as you would the furniture in your home. Polish wood surfaces sparingly with a good quality wax or spray polish. Use a damp cloth to clean melanate laminated surfaces. (iv) The solution should be emptied from the container. (v) COOKING EQUIPMENT Caustic pastes, abrasive cleaning powders, coarse wire wool and hard implements will damage the surface. The opening of any container should be cleaned thoroughly with an appropriate preprepared wipe impregnated with a disinfectant / sterilizing solution. (vi) External containers should be inverted whilst stored overnight (if possible). CARPETS, UPHOLSTERY AND CURTAINS (vii) Containers must be filled with mains water only and mains water only should be used for the above cleaning procedure. Vacuum clean carpets and upholstery to ensure a long life, marks on cushions can be removed using a mild upholstery shampoo with the minimum of water. Curtains should be dry cleaned only. (viii) On no account should garden hoses be used to fill water tanks. WARNING: Under no circumstances should alcohol, spirit or solvent-based liquids be used on GRP or ABS plastic panels as these substances may react with the material and cause visible damage. SHOWER TRAYS, SHOWER ROOM AND WASH BASIN FITTINGS Only clean your shower tray using soap and water. Do not use chemical based cleaning agents as this may attack the material of the tray. CLEANING OF ALL TAPS It is recommended that a non-abrasive damp cloth be used for cleaning the taps and showers. 11-2 CARE OF YOUR CARAVAN WATER SYSTEMS - STERILIZATION THETFORD TOILET Clean the water system at the start and end of the season with sterilizing fluid. When cleaning it is advisable to use a sterilizing fluid e.g. Chempro SDP or similar. WARNINGS • Cold Weather Use - to prevent freezing during cold weather use, add antifreeze to the toilet system fresh water tank. Use a non-toxic (propylene glycol) type of antifreeze. Refer to chart on container to obtain level of protection. • Warmer weather or longer intervals between emptying the waste tank may require additional toilet fluid. Use only Thetford toilet fluid to achieve the best results. Please Note: It is recommended that for this operation the filter is removed as the fluid reduces the effectiveness of a new filter. (i) Drain down the system. (Open all taps to allow air in, enabling the system to drain quickly.) See Index - Water System, Draining. (ii) Remove any water filters fitted, and replace with a short length of hose or empty filter cartridge (this will ensure the filter is not affected by the disinfectant / sterilizing solution). CAUTIONS (iii) Fill the system by using the pump with a disinfectant / sterilizing solution. (Check that the solution at full strength appears at all taps/showers). Allow to stand for the recommended period of time. (iv) Drain the system down completely. (v) Thoroughly clean the outside of all taps/ connectors with a cloth soaked in the disinfectant / sterilizing solution. (vi) Flush the system through with clean drinking water until no traces of disinfectant / sterilizing solution can be detected at any tap. (vii) After sterilizing the system at the start of the season it is recommended that a new Ultraflow filter cartridge should be fitted. Please Note: Suitable sterilizing chemicals are available from your Elddis Retailer, accessory shop, chemists, or home-brew shops. It is not, however, recommended to use bleach or sodium met bisulphide. TRUMA SPACE HEATER Please note: Your Truma Space Heater front is now attached using 2 screws. These screws must be removed prior to removal of the Space Heater front. These screws can be seen when looking into the fire through the air vents. 11-3 • Never add toilet fluid directly into toilet bowl. • Do not use strong household detergents or cleaners that contain chlorine, solvents or acid contents. • High Altitude and Hot Weather Use with large temperature differences and changing heights during towing, over pressure can start to build up in the waste holding tank, causing contents to splash upward upon opening the valve blade if opened too fast. CARE OF YOUR CARAVAN CHASSIS MOUNTED SPARE WHEEL CARRIER Tyre Wear and Damage The legal requirements for tread depth on motor vehicle tyres apply also to caravans. Similarly, it is not permitted to mix cross-ply and radial tyres on the same axle. A redundant tyre must be replaced by one of the same size and construction. Wheels should be balanced and changed round occasionally to equal wear and prolong the life of the tyres. A tyre should be renewed if a blister, rupture or cut exposing the casing is detected. If the tyre has suffered a violent impact e.g. against a kerb, it should be examined by a specialist as soon as possible. Each caravan chassis has a set of punched holes immediately behind the axle to enable fitting of a spare wheel carrier. To gain access to your spare wheel lift the spare wheel carrier up and lift up the locking mechanism. Then move the mechanism to the horizontal position and the spare wheel carrier will be free to move over the mechanism and allow the spare wheel to drop to the floor to be removed. To replace the spare wheel simply reverse the operation making sure that the quick release mechanism has been fully pushed down to create a positive lock. The carrier is of extra strong, lightweight construction and zinc plated for all weather protection. It is easy to fit and accepts all conventional wheel sizes. Please Note: It is customary for tyre manufacturers to mark tyres with load and inflation data. It is important to understand that this information relates only to the use of tyres on cars. CHANGING A WHEEL Whenever road wheels are removed and refitted, they must be tightened using a calibrated Torque Wrench set to 92 Nm for steel wheels and 115Nm for alloy wheels. Only use the wheel bolts supplied with your caravan. If you need to replace these bolts you should obtain bolts from an approved Elddis Retailer. The bolt fixings should be tightened in the sequence shown in the diagram below. Do NOT simply tighten clockwise or anti clockwise. Remember to over tighten is just as dangerous as to under-tighten, as this can distort the wheel rims. Avoid the use of power wrenches. Wheel bolts should NEVER be lubricated. TYRES Please refer to Section 18 Technical Specifications which is contained within this handbook for information regarding tyre pressures and axle loads. Pressures It is customary for manufacturers to mark tyres with load and inflation data. This information relates to the use of the tyre on cars. It is dangerous to drive with under inflated tyres. The pressures (cold) recommended by the manufacturers should be regarded as a minimum. Pressure checks, including those on the spare tyre, should be made with the tyres cold and using an accurate pressure gauge. The checks should be carried out before each journey and at regular intervals during storage. 11-4 CARE OF YOUR CARAVAN The corner steadies must not be used to jack up the caravan. They can be lowered to touch the ground only as a safety measure to stabilise the caravan. (i) Apply the handbrake fully as for parking. Do not forget to give the caravan a slight rearwards push to stop the reversing lever collapsing. (ii) Slacken off the wheel bolts on the wheel to be changed. (xi) Raise the corner steadies. (xii) Lower the caravan to the ground. (xiii) The wheel bolts should be tightened ensuring that the torque is applied evenly around the wheel. Using a suitable torque wrench, sequentially tighten the steel bolts to a torque of 92Nm for steel wheels and 115Nm for alloy wheels following the sequence stated above. IMPORTANT (iii) With a suitable jack, jack up the caravan under either the axle tube or the axle mounting plate. • The torque settings should be rechecked after 50 km (20 miles) and every 5000 km (3100 miles) thereafter. Please Note: Do Not Use The Chassis As A Jacking Point. If there is lack of ground clearance because of a flat tyre, gently move the caravan onto some ramping boards. • Do not loosen the wheel bolts to carry out this operation whilst the road wheel is supporting the weight of the caravan. (iv) Support the weight of the caravan with the jack and for added safety lower the front and rear corner steadies on the side of the flat tyre. Then remove the ramping boards. • Wheel bolts should NEVER be lubricated. • NB: If you upgrade from steel to alloy wheels you must ensure you use the correct bolts for the new wheel. (v) Remove the wheel bolts and remove the wheel. JACKING (vi) Before fitting the wheel, examine it for distortion or other damage. Ensure that all mating surfaces are clean and dry, including bolt/nut seats. Under no circumstances should the corner steadies be used to jack up the caravan. When it is necessary to jack up, use a bottle, screw, trolley or scissor type jack, one with an axle shaped head is recommended. Please Note: Always Use the Correct Bolts to Secure the Wheel - Check with the dealer if unsure. Place the jack plate under the axle tube as near as possible to the main longitudinal member. The maximum mass which the jockey wheel and its clamping mechanism are capable of withstanding is 150kgs. Please Note: A corner steady brace is not to be used for the next step. (vii) Insert the wheel locating pins (supplied within your Elddis kit box) into holes 4 and 5 and then slide the wheel onto the locating pins. LUBRICATION • Lubricate the Jockey Wheel (viii) Insert the wheels bolts into holes 1 then 2 and then 3. • Lightly oil the wheel axle and screw thread. • Lubricate the Brake Linkage (ix) Remove the wheel locating pins from holes 4 and 5 and insert the wheel bolts. • Lightly oil all moving parts. • Lubricate the Corner Steadies • Lightly oil the screw and pivot pins. (x) After the bolts have been screwed in as far as possible by hand, each bolt should be tightened gradually in sequence. Do not over tighten at this point as the final tightening should be done with a calibrated torque wrench. The wheels of the caravan will not rotate during tightening as they are held rigid by the wheel hub brake unit. 11-5 CARE OF YOUR CARAVAN MAINTENANCE OF YOUR BPW CHASSIS CATEGORY OF EXPOSURE & DURATION OF PROTECTION The BPW chassis is protected by a hot dip galvanising process in accordance to DIN EN ISO 1461. The duration of protection is according to a salt spray test to DIN 50021 standard. WARNING: Holes must not be made without approval of the chassis manufacturer. The following maintenance instructions relate to the BPW chassis fitted to your Elddis caravan. They are a constituent part of the warranty conditions. Adhere to the relevant operating instructions of the vehicle manufacturer or of the other vehicle component manufacturers. axles and suspensions without any risk to safety. This applies even if an accredited test authority has already tested such products. Completion of the maintenance work in accordance with the prescribed intervals is essential in order to maintain the operating safety and roadworthiness of the vehicle. Procurement of Spare Parts Our warranty becomes null and void if spare parts other than original BPW parts are used. The code and type numbers of the axle and chassis components enable us to quickly determine your exact spares requirements when ordering from our BPW agencies and service stations. It is therefore recommended that you enter the data shown on the type plate in the following table so that it is readily available when required. The type plate or the imprint is located on the axle tube or on the housing of the towing equipment and couplings. The correction of any defects found or the replacement of any worn parts should be carried out by a BPW after sales service workshop, unless the vehicle user has at his disposal appropriately skilled in company workers and the necessary technical facilities. Please Note: When installing spare parts, it is strongly recommended that only original BPW components are used. Parts approved by BPW for caravan axles and suspensions regularly undergo special test procedures and as a result BPW is able to guarantee their quality. However, BPW cannot assess for every single third party product whether it can be used for BPW caravan Please Note: For full maintenance details of the BPW chassis, undergear and Winterhoff coupling please refer to the individual manufacturer’s handbook supplied within your user information pack. 11-6 STORAGE CARAVAN COVERS STORAGE Caravan covers may be used to protect your new Elddis caravan provided that the cover used is of a breathable type. LONG TERM & WINTER STORAGE If the caravan is to be stored for any length of time, especially over the winter period, the following operations are recommended: (i) Remove all linens, blankets, cushions, clothes, mattresses, etc, that could be affected by damp conditions. (ii) Clean the caravan inside and out as detailed in the previous section. Ensure that the point of extending aerials or the status aerial (depending on model if fitted) are removed or retracted, and that the cover is well tied down to avoid the cover being punctured. Your caravan must be ventilated every 4 to 6 weeks if it is to be stored with a cover in place. POWER DRAIN (iii) Drain the water system (see Water system). In order to reduce any drain on your leisure battery while your caravan is being stored ensure that the main control switch on the refrigerator is set to the ‘0’ position (iv) For winter storage and to prevent frost damage all taps must be left in open position. For those caravans with lift up taps please ensure the taps are left in the central position. (v) Please Note: Do not work under the caravan unless the corner steadies are down and the axle is supported. Ensure all windows, roof lights and doors are correctly fastened. Check fixed ventilation apertures are not obstructed. Should the caravan be stored for a prolonged period of time it is strongly recommended that the caravan is fully serviced before the commencement of use. Your retailer will ensure that your caravan is safe, secure and ready for your enjoyment. (vi) Ensure that the refrigerator/freezer compartment doors are secured in the vent position using the door catch. (vii) Check that the site you have chosen to store the caravan is open, fairly high and dry and if possible not exposed to gales etc. If this proves impossible it is recommended that the caravan chassis is anchored to the ground. Please Note: Caravans stored for any length of time should not have the handbrake or brakes applied. The wheels should be chocked or wedged and the handbrake released. The hitch head should be checked to see that it is fully extended and that there is no load on the braking system. (viii) Jack up the caravan (use bottle or screw jack, do NOT use the corner steadies) so that the wheels are clear of the ground. (ix) Support the caravan axle with wooden blocks, axle stands or similar so that when the jacks are removed the wheels remain clear of the ground. Lower the corner steadies to ‘just’ site the caravan. Cover the tyres to prevent deterioration. Release the handbrake. (x) Security: Lowering and locking the corner steadies and removing the wheels will reduce the risk of caravan theft. 12-1 STORAGE 12-2 WARRANTY (ii) WARRANTY 3-YEAR MANUFACTURER’S WARRANTY Subject to the following conditions, your caravan is supplied with a manufacturer’s warranty for 3 years from the original date of purchase, at no additional cost to you the customer. We sincerely hope you will never have cause to complain about your caravan. However, if you do have a problem then please contact your Retailer so they can report this through our warranty system. We are confident they will do their utmost to resolve any problems to your complete satisfaction. The Retailer from whom the caravan is purchased is liable for warranty repairs. Any other approved Retailer or Service Centre may carry out work at his own convenience and/or discretion, but is not obliged to do so. (iii) That an “annual” service, damp and safety check has been carried out by an approved Retailer or Service Centre. The first and second services are due 60 days either side of the anniversary of the original date of purchase. The interval between services must not exceed 14 months. The third service must be on or before the anniversary date of the original purchase. (iv) That original VAT service invoices are retained as proof that annual service and inspections have been carried out. (v) PARTS COVERED BY THIS WARRANTY FOR YEARS 1 - 3 No work should be commenced under the terms of the warranty unless prior authorization is obtained from The Explorer Group. (vi) Explorer Group reserves the right to inspect the caravan before any work commences. Subject to the specific exclusions in years 2 and 3 set out below all original components of the caravan, including permanently fitted equipment, forming part of the manufacturer’s original specification. (vii) No liability will be accepted for damage caused by fair wear and tear, wilful damage, negligence, abnormal working conditions, intrusion of foreign or harmful matter, overheating, freezing, failure to follow The Explorer Group instructions, misuse or alteration or repair of the caravan without The Explorer Group prior approval. SPECIFIC EXCLUSIONS FOR YEARS 2&3 Microwave, tyres, batteries, plastic windows, glass, exterior paint work, bright work and all similar trim and finish, soft furnishings, carpets and floor coverings. Entertainment/communication systems and connected equipment. Adjustment of blinds, hinges, catches, stays and doors. Replacement bulbs, fluorescent tubes, fuses and electrical connections, locks; GRP, ABS and PVC products including A-frame covers, wheel spats and shower trays. Natural movement of internal doors and furniture. Normal wear and tear/ servicing items and other components subject to routine maintenance. (viii) Caravans covered by this warranty shall not be put out to hire, reward, or any other commercial use or used in any timed race. (ix) That the caravan shall be used only for its ordinary and intended purpose and shall not be subjected to any condition which could reasonably be foreseen to cause or result in damage or excessive wear and tear. (x) That only private cars or 4x4 type vehicles substituting as private cars, shall have towed the caravan. CONDITIONS ATTACHED TO THE WARRANTY: (xi) That no liability arises from this warranty for transport costs to and from the place of remedial work or consequential cost relating to transportation. No liability arises out of this warranty for any indirect, special or consequential loss or damage (whether for loss of profit, use, contract, goodwill, or Failure to comply with the following conditions may invalidate your Warranty. (i) That the original construction of the caravan has not been tampered with or repaired other than by Explorer Group or an approved Retailer or Service Centre. The duration of the warranty is 36 months from the original date of purchase. 13-1 WARRANTY otherwise), costs, expenses or other claims for compensation howsoever arising. (xii) No liability will be accepted for any accidental or fire damage or any loss incurred by accident or fire. (xiii) The unexpired period of the 3-year warranty or the 5 year water ingress is transferable to second and subsequent owners during the warranty period. The new owner should contact Explorer Group within 3 months of their purchase, with proof of ownership, service history and their payment of £30 to have their details recorded in our database. Please Note: This warranty does not affect the purchaser’s statutory rights. This warranty shall be governed and construed in accordance with the laws of England and the parties irrevocably submit to the exclusive jurisdiction of the courts of England. 13-2 CODE OF PRACTICE - WATER INGRESS CUSTOMER OBLIGATION - SERVICING CODE OF PRACTICE - WATER INGRESS It is a condition of your warranty that your caravan must have an “annual” service, damp and safety check and this should be carried out by an Explorer Group approved Retailer or Service Centre, in accordance with NCC guidelines. Proof of this will be required in the event of a warranty claim. At Explorer we want our customers to be sure that, in buying one of our caravans, you are buying the very best. We would like you to continue to believe this for a long time after you have made your purchase. We are confident that our new caravans, built with innovative manufacturing techniques and tested materials, make water ingress concerns unnecessary. We are so confident of our new caravans that we follow a ‘Code of Practice’ which gives certain guarantees to our customers, both consumers and Retailers, of financial reimbursement for remedial work costs should problems occur. Please Note: Failure to do so will invalidate your warranty. The first service is due 60 days either side of the anniversary of the original date of purchase. The interval from purchase date to the first service and the intervals between services must not exceed 14 months. Years 3 and 5 must be on or before the anniversary date of the original purchase. THE CODE The code applies to all new Explorer Group products manufactured after 1st September 1998. All owners with documentary proof of annual services by an approved Explorer Group Retailer or Service Centre will be paid in full for the costs of remedial work due to water ingress. This is valid for up to 5 years from the original date of purchase of a new product. Unless the caravan has a full service history, the owner will be required to contribute to the costs of remedial work for water ingress damage depending upon the age of the caravan and work required. Each case will be examined on its own merit. Explorer will decide the amount of contribution towards the remedial work costs. Owners exchanging their current Explorer Group model for a new Explorer Group model will not have the value of their part exchange reduced due to potential water ingress issues, providing that there is documentary evidence that the caravan has been annually serviced and that it is less than 5 years old. Your caravan requires servicing for safety, efficiency and to protect the investment you have made. Whether the caravan is used for short trips or continental long range touring, regular servicing is necessary and will ensure continued enjoyment of your caravan. Your Retailer or Service Centre will carry out your service using the latest techniques and equipment (a list of the items to be inspected, tested and adjusted appears on the Service Vouchers in this handbook), and should provide you with the service document as proof of regular maintenance. As with motor vehicle service documents, not only will the proof of regular servicing enhance your caravan resale value, but in the unlikely event of any defect appearing at some later date a properly serviced and documented caravan history will enable your Retailer to rapidly assess and where appropriate, carry out the necessary remedial work. CONDITIONS ATTACHED TO THE CODE MAINS ELECTRICS It is recommended that you have your Mains Electrics System inspected by an NICEIC approved contractor every 3 years. (i) Work may only be undertaken after approval by Explorer (depending upon individual circumstances). SPARE PARTS (ii) Explorer will pay the costs of remedial work, only after approved work has been carried out. Should you require any replacement parts for your caravan it is necessary that you contact the Retailer from whom you purchased the caravan or any Explorer Group approved Retailer and give the following information, which will help in (iii) The Code is not retrospective. Caravans traded-in prior to implementation of the Code are not covered. 14-1 CODE OF PRACTICE - WATER INGRESS identifying the required component: (i) Model and make of caravan (ii) VIN number (iii) Description of required part (iv) Photograph, size or diagram of required part Please Note: All parts must be ordered and supplied through an approved retailer. REMEDIAL WORK The Explorer Group together with its suppliers is continually undertaking extensive research into testing, remedial work procedures and materials such as sealants, adhesives, gaskets and tapes. Therefore, if for any reason your new caravan is damaged or requires remedial work then only an approved Explorer Group Retailer or Service Centre should undertake such work. All such work should be undertaken using only approved Explorer Group genuine parts, recommended sealant and following Explorer Group procedures. Explorer will also undertake to supply certain specialist repairers with the necessary spare parts. In this case, your selected repairer must contact the PARTS DEPARTMENT with all enquiries. 14-2 CARAVAN CONSTRUCTION CARAVAN CONSTRUCTION MAIN COMPONENTS FRONT PANEL AND GAS BOTTLE LOCKER LID The following is a brief description of the main components used in your caravan. More comprehensive descriptions can be found in the equipment manufacturers literature held in the Owner’s Information Pack. AWNING CHANNEL These are constructed from moulded GRP for strength and lightness. Each caravan is fitted, as standard, with an awning channel as an integral part of the near- and/or offside aluminium roof and body side moulding. If it is found necessary to fit additional attachments, care must be taken to ensure that any holes which are drilled in the outside of the body are correctly sealed. Awnings which employ rubber sucker attachments rather than screw fixings are recommended. BPW CHASSIS BPW are one of the largest producers of caravan chassis in Europe. The chassis is galvanized special steel fitted with neidhart axles and suspension system. Elddis utilizes the new BPW V-TEC Chassis System. BRAKING SYSTEM ADDITIONAL FIXINGS TO YOUR CARAVAN SHELL The Braking System comprises a rod operated overrunning device with expander mechanism and adjuster box. An automatic reversing system with a spring loaded reverse lever is attached to the adjuster box. The system also incorporates a link device, which gives added safety to the handbrake operation when parking on a reverse slope or steep hill. Brake adjustment instructions are given in the maintenance section of this guide. On NO account should screw threads longer than 5/8th inch (15mm) be permitted to enter the shell sandwich (from inside). Ensure that all screws are of the self tapping type. No screw or any other object should be permitted to enter the ceiling of your new caravan. Please Note: Holes must not be drilled into the chassis. When purchasing a stabilizer, consult your retailer who will advise on the correct type to fit. BODY SHELL Caravan bodies are constructed from the highest quality materials. The fully insulated floor is constructed from a timber frame with plywood and insulation laminated together for strength. The walls comprise an insulated foam sandwich having pre-coated aluminium exterior surface and vinyl coated plywood interior finish. Wooden framing is positioned within the sandwich to add strength. The very latest ‘state of the art’ presses are employed to produce the extremely well insulated, robust, yet lightweight sections. WINDOWS Windows are all of a double glazed acrylic construction and the door frames are extruded aluminium. INSULATION Elddis caravans are built to thermal insulation Grade 2. This states that an average temperature difference of at least 20K between inside and outside temperatures should be achieved when the outside temperature is 0ºC. 15-1 CARAVAN CONSTRUCTION 15-2 EQUIPMENT LIST EQUIPMENT LIST ODYSSEY REFRIGERATOR THETFORD N112 LCD HEATER TRUMA ULTRAHEAT AUTO INTERNAL BLOWN AIR TRUMA PUSH FIT RAPID INSTALLATION WATER HEATER TRUMA ULTRASTORE SINK AND DRAINER OVEN ARGENT STAINLESS STEEL SPINFLO MIDI PRIMA WITH ILLUMINATION & 2 SHELFS MICROWAVE BCA DIGITAL 700 W CW SURROUND HOB SPINFLO 3 BURNER HOB TAPS KITCHEN DIMATEC SINGLE LEVER MIXER SHOWER EQUIPMENT DIMATEC MIXER TAPS VANITY DIMATEC SINGLE LEVER MIXER WATER FILTER / PUMP WHALE COMPLETE SYSTEM LIGHTS 12V FLUORESCENT LUMO & CROWN ICE LIGHTS 12V DOWN LIGHTS ZOE EYEBALL HALOGEN LIGHTS 230V MAINS SARGENT LIGHTS 12V HALOGEN NOVA CONTROL PANELS CBE ELECTRICAL FITTINGS CBE TOILET THETFORD ROTATABLE WITH ELECTRONIC FLUSH CASSETTE BLINDS SEITZ SERIES 2000 16-1 EQUIPMENT LIST 16-2 ELECTRICAL DRAWINGS ELECTRICAL DRAWINGS 13 PIN PLUG WIRING DIAGRAM 17-1 ELECTRICAL DRAWINGS WIRING DIAGRAM - ODYSSEY 17-2 ELECTRICAL DRAWINGS ROAD LIGHTS - ODYSSEY 17-3 ELECTRICAL DRAWINGS 17-4 TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS ELDDIS ODYSSEY Model Number of Berths 482 524 2 4 Interior Length 4828mm (15’10”) 5344mm (17’6”) Exterior Body Length 5660mm (18’8”) 6176mm (20’3”) Shipping Length 6550mm (21’6”) 7066mm (23’2”) Overall Width 2286mm (7’6”) 2286mm (7’6”) Overall Height 2580mm (8’6”) 2580mm (8’6”) Maximum Headroom 1908mm (6’3”) 1908mm (6’3”) Interior Width 2150mm (7’1”) 2150mm (7’1”) Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi 5.5J x 14 5.5J x 14 175 R 14 99 185 R 14 102 60 61 200/50 250/40 9075mm (29’9”) 9590mm (31’5”) 2 x Single 1880mm x 720mm (6’2” x 2’4”) or 1 x Double 2074mm x 1480mm (6’10” x 4’10”) 2 x Single 1880mm x 720mm (6’2” x 2’4”) or 1 x Double 2074mm x 1480mm (6’10” x 4’10”) Side Dinette Not Applicable 1 x Single 1800mm x 635mm (5’11” x 2’ 1”) and 1 x Lift Up Bunk 1650mm x 570mm (5’5” x 1’101/2”) Rear Bed Sizes Not Applicable Not Applicable Brake Size Awning Sizes Ground to Ground Front Bed Sizes M.T.P.L.M. 1400kgs (27.5cwt) 1540kgs (30.25cwt) Mass in Running Order 1224kgs (24.04cwt) 1339kgs (26.30cwt) Essential Habitation Equipment 53kgs (1.04cwt) 53kgs (1.04cwt) Maximum User Payload 176kgs (3.46cwt) 201kgs (3.94cwt) Maximum Hitch Weight 100kgs (1.96cwt) 100kgs (1.96cwt) Optional Equipment Payload 16kgs (0.31cwt) 16kgs (0.31cwt) A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissible Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Note 4: The overall height has been measured with the aerial in the down position. 18-1 TECHNICAL SPECIFICATIONS ELDDIS ODYSSEY (continued) Model Number of Berths 544 550 4 4 Interior Length 5599mm (18’5”) 5599mm (18’5”) Exterior Body Length 6429mm (21’0”) 6429mm (21’0”) Shipping Length 7319mm (24’1”) 7319mm (24’1”) Overall Width 2286mm (7’6”) 2286mm (7’6”) Overall Height 2580mm (8’6”) 2580mm (8’6”) Maximum Headroom 1908mm (6’3”) 1908mm (6’3”) Interior Width 2150mm (7’1”) 2150mm (7’1”) Wheel Rim Tyre Size Tyre Pressure at MTPLM in psi Brake Size Awning Sizes Ground to Ground Front Bed Sizes Side Dinette 5.5J x 14 5.5J x 14 185 R 14 102 185 R 14 102 63 63 250/40 250/40 9950mm (32’6”) 9950mm (32’6”) 1 x Double 2074mm x 1200mm (6’10” x 3’11”) 1 x Single 1813mm x 720mm (6’0” x 2’4”) and 1 x Single 2113mm x 720mm (6’11” x 2’4”) Not Applicable Not Applicable Rear Bed Sizes Fixed Bed 1 x Double 1830mm x 1270mm (6’0” x 4’2”) Fixed Bed 1 x Double 1843mm x 1346mm (6’1” x 4’5”) M.T.P.L.M. 1575kgs (30.94cwt) 1550kgs (30.45cwt) Mass in Running Order 1371kgs (26.76cwt) 1346kgs (26.25cwt) Essential Habitation Equipment 53kgs (1.04cwt) 53kgs (1.04cwt) Maximum User Payload 204kgs (4.00cwt) 204kgs (4.00cwt) Maximum Hitch Weight 100kgs (1.96cwt) 100kgs (1.96cwt) Optional Equipment Payload 16kgs (0.31cwt) 16kgs (0.31cwt) A manufacturing tolerance has been added to Mass in Running Order before calculating the Maximum User Payload. Maximum User Payload includes Essential Habitation Equipment, Personal Effects and Optional Equipment. Note 1: Please take care to ensure that you have allowed for the masses of all items you intend to carry in the caravan. Note 2: Warning under no circumstances must the Technical Permissible Laden Mass of the caravan be exceeded. Note 3: All data is calculated using metric weights and measurements. The imperial figures quoted are conversions thereof. Note 4: The overall height has been measured with the aerial in the down position. 18-2 GENERAL QUESTIONS GENERAL QUESTIONS Q: Where Can I Obtain Your Latest Brochure? A: Our latest brochures are available from Approved Retailers or can be viewed and printed from the download section on our website www.explorer-group.co.uk. A request form can also be completed should you wish to receive a printed copy of our latest brochures. Q: Why Is the Handbook Not Specific To My Model? A: Many of the components used in the manufacture of our caravans are identical throughout our model ranges, so we produce a generic handbook, which covers all models manufactured for that season. If the literature supplied with your caravan does not answer your question then please contact your Retailer for further assistance. Q. I Require Technical Or Other Information, Who Can Help Me? A. The majority of information you require is available through your Elddis Retailer. Q - Can You Tell Me The Second Hand Price Of My Caravan? A - As a manufacturer we are not involved in the second hand market. You should contact a Retailer, The Camping and Caravanning Club and/or The Caravan Club. They should be able to give some indication of market value. Q: How Can I Avoid Excessive Caravan Snaking When I Tow And What Should I Do If It Starts? A: Elddis has extensively tested our caravans and we are confident of their stability. However, many other factors can influence your towing unit. When loading your caravan put heavy items low down and mainly over the axle(s). You should not stow tins, bottles or heavy items in overhead lockers, during towing. Everything else should be distributed evenly around your caravan, front and back, and each side of the centre line should snaking start, if at all possible don’t brake and don’t compensate by steering into the swings. Just ease up on the accelerator and allow your speed to gradually decrease until the snaking subsides. Q: What Is The Correct Awning Size For My Caravan? A: Ground to ground awning measurements for Elddis caravans can be found by looking in the latest model section, the Product Archive section on our website, or by referring to the relevant Technical Specification section of this handbook. However, we advise you verify this information by threading a piece of string through the awning channel from ground to ground, and then by measuring the string. Your awning manufacturer will then advise on the nearest size of awning appropriate for your measurement. Q: Can I Fit A Bicycle Rack/Top Box/Air Conditioning To My Caravan? A: It may be possible to fit accessories to your caravan but this will depend upon the internal construction of the roof/walls and whether they can support the weight of the accessory. If it is possible your Retailer will be able to advise you, (or alternatively they will obtain confirmation and a drawing where necessary, from Elddis). Please note that weight of any accessories will reduce your User Payload allowance. Q: My Interior Lights Are Not Working, What Do I Do? A: It is possible that all of the 230V mains electrical equipment may not be operated simultaneously. Check fuses, battery connections and power supply (master light switch). Refer to your Retailer for further assistance. PLEASE NOTE: The internal lights in your caravan will not operate whilst the caravan’s electrical hitch cables are connected to a towing vehicle with the engine running. 19-1 GENERAL QUESTIONS Q: Where Can I Get Spare Parts For My Caravan? A: Retailers will be able to source most parts you require. For details of your nearest Elddis Retailer please refer to our Find A Retailer section on our website, or call 01207 699 000 for assistance. Q. How Many Years Will Spare Parts Be Available For My Caravan? A. Elddis will endeavour to supply spare parts for a caravan, for at least 8 years from new. Q. What If The Parts Are No Longer Available? A. Where an original part is no longer available, whenever possible we will suggest a suitable alternative if it is available. Q. Who Can Carry Out Warranty Work On My Caravan? A:Your supplying Retailer is obliged to undertake your warranty work. However, any approved Elddis Retailer or Service Centre can undertake the work, but this is at their discretion. We will also accept services completed by a NCC Jones Vening approved company, but they will not be able to undertake warranty work if they are not approved by Elddis. Q. Why Don’t You Stock Parts At The Explorer Group Factory? A. Due to the volume of models we produce it is not possible for us to maintain stock levels of every individual component used in our manufacturing process. We do stock commonly requested items, but some items must be made to order. Q. I Am Having Trouble Booking My Caravan For Its Service, In Line With The Requirements. What Timescale Is Acceptable? A. We will allow a delay of 60 days after your service is due, but subsequent annual services should still be undertaken as close as possible to the anniversary of the original date of purchase. Except for 3rd and 5th services which must be on or before the anniversary of the original date of purchase. We would recommend that you plan these services in advance to ensure you can meet the above requirements. Q. I Have A Problem With My Caravan, Who Can Help Me? A. We would always recommend that you contact your supplying Retailer. Your local Elddis Retailer or Elddis Approved Service Centre may be able to assist. An inspection can then take place and the necessary course of action agreed. Q. I Am Unhappy With The Service I Have Received From My Retailer/Service Centre, Where Do I Go From Here? A. We would recommend that you write to your Retailer/Service Centre, detailing your problems and requirements, requesting a response explaining how they will resolve your complaint. A copy of your letter can also be forwarded to The Elddis Customer Services Department, quoting the serial number of your caravan and the name of the Retailer/Service Centre. Please be assured that we will assist your Retailer/Service Centre in resolving any problems. 19-2 GLOSSARY Bunk Bed GLOSSARY This is a sleeping place, usually higher up than a conventional bed. Often (but not always) this can be folded or removed to provide additional living space. 13 pin plug The plug used to connect the caravans electrical system to your towing vehicle to enable the road lights, refrigerator and battery charger to operate during towing. Butane This is the triangular part at the front of the caravan’s chassis which is between the main body and the hitch it is also called the drawbar. Is a form of Liquefied Petroleum Gas (LPG) which normally comes in blue cylinders. This type of gas is most commonly used in the UK, although a switch to propane is advised in severely cold weather conditions. ABS Calor This is an acronym for anti-lock braking system. This is the main supplier of propane (red) gas cylinders and significant seller of butane (blue) gas. A Frame Actual Laden Weight This is the total weight of the caravan when loaded ready for use by the end user. Campingaz This is the trade name of Butane gas. Aquaroll Cassette Blind Brand name used generically for a water container that rolls so you don’t need to lift it. This is a roller blind which is fitted as part of the window assembly, often along with a flyscreen, thus giving a neat installation. Awning This is a tent-like structure of fabric over a supporting framework, which can be attached to the side of caravan. Cassette Toilet A form of chemical toilet found in modern caravans, where the waste holding tank can be accessed and emptied from, outside. Battery Charger This is required to keep a leisure battery charged. All caravans include a charging facility which operates via the mains hook-up, and also has the ability to recharge from the tow car’s alternator while travelling. Chemical Toilet Most modern caravans have them, with more up market models having a fully plumbed-in flushing version. Berth(s) Control Panel Sleeping place - Refers to the number of people a caravan can accommodate for sleeping. Used as the description for the panel of electrical switches and gauges governing 12V and mains electricity systems. Blown Air Heating Corner Steadies A method of heating the living quarters of a caravan by use of a fan pushing air out through a number of outlets. The winding device built into each corner of a caravan chassis that is used to stabilise the body once set up on a pitch. Breakaway Cable A thin steel cable linking the caravan handbrake to the vehicles tow bar - In the event of the caravan becoming detached from the car, the cable will pull the caravan handbrake on before snapping. 20-1 GLOSSARY Coupling Head - See hitch. Gas Drop out Holes CRiS These are not part of the ventilation. LPG is heavier than air, so holes through the floor below gas-powered appliances allow any leakage of gas to exit the habitation area. This is the Caravan Registration and Identification Scheme. It is a voluntary scheme which registers caravans in a similar manner to how motor vehicles are registered. Allows you to check the legitimate right to ownership of the seller of a secondhand caravan, and helps in the recovery of stolen caravans. Grey Water This is the waste water from sink/shower. Gross Train Weight This is also known as Combined Weight. The maximum permitted weight of an outfit as specified by the tow car manufacturer. Dinette This is a popular style of seating arrangement where two seats or settees face each other across a table. Gross Vehicle Weight (GVW) This is the weight of the vehicle laden to its maximum, as defined by the manufacturer. See also MTPLM. Earth Leakage Circuit Breaker ELCB Earth leakage circuit breaker - see residual current device (RCD) GRP ELCB Earth Leakage Circuit Breaker. More normally termed RCD. Is Glass-reinforced plastic, but more commonly known as glass fibre (not fibre glass, which is a trade name). Essential Habitation Equipment Handbook Those items and fluids required for the safe and proper functioning of the equipment for habitation as defined by the manufacturer of the caravan. This includes items such as the leisure battery and gas cylinders, plus water contained in the water heater etc. This is a owners manual, a guide to the workings of your caravan. Flyscreens Hitch Mesh fittings for windows doors and roof vents, to keep out insects etc. This is the mechanism which allows a caravan to be attached to a tow ball. Free-Standing Table Hitch Lock This is a table which, because of its leg design, can be used inside or outside. A security device that prevents the caravan hitch being used. Full Service Pitch Hook-Up This is a pitch which has individual provision for fresh water supply and waste water disposal, in addition to mains electricity and in some cases TV aerial connection. This is a facility on a pitch for connection to mains electricity. Hardstanding This is a pitch which has a hard surface made of gravel, asphalt, concrete etc, instead of grass. Ingress Usually meaning water ingress, a possible problem where water seeps in at the joins, usually as a result of worn sealant. Gas Cylinder This is a portable, pressurized container for the storage of LPG. Gas Cylinder Locker Is the compartment on the caravan for the storage of gas cylinders. 20-2 GLOSSARY Jack Maximum User Payload This is a device for raising the vehicle so that a wheel can be changed, for instance. Not to be confused with corner steadies which although they are sometimes referred to as ‘corner jacks’ are steadying, not lifting devices. This is the maximum payload available for the user including essential habitational equipment. MIRO - Mass In Running Order Weight of the caravan equipped to the manufacturer’s standard specification. Therefore the condition in which it leaves the factory. Note that this does not include any part of the user payload, including the essential habitation equipment. Jockey Wheel The small front wheel attached to the caravan Aframe used to support the forward end of the caravan, when detached from the towing vehicle. Kerb Weight MTPLM - Maximum Technically Permissible Laden Mass This is the empty weight of a motor vehicle as defined by the manufacturer. The technical maximum permissible laden weight of the caravan, this must not be exceeded. Layout National Caravan Council This is the interior design and details where furniture units are placed in relation to each other. The only trade association representing manufacturers, retailers and suppliers within the caravan industry. Leisure Battery Nose weight This supplies the power for the caravan electrical systems and is sometimes called an auxiliary battery. The weight exerted on the tow bar. Special scales are available from accessory shops for measuring this weight. Levelling The process of ensuring that a caravan is level when sited on a pitch. It is important for comfort and also to ensure the correct functioning of the fridge and water systems. Number Plate LPG Optional Equipment Payload Liquid Petroleum Gas, i.e. butane or propane. The payload required for equipment to enable the caravan to be used for habitation purposes. Caravans must display a legal number plate showing the same registration mark as their towing vehicle. L-Shaped Outfit This is a term where the seating area of a caravan is indeed L-shaped. The caravan and its towing vehicle considered as a unit. Mains Hook-Up Owners’ Club This is a campsite facility where you can plug into a mains electricity supply. Maximum Hitch Height This is a group of people who usually own the same brand of caravan and enjoy meeting up for rallies. The maximum height at which the hitch should be connected to a towing vehicle Payload The amount you can put into a caravan. Specifically the difference between the Maximum Technical Permissible Laden Mass (MTPLM) and the Mass In Running Order (MIRO). Maximum Permissible Towing Weight This is the maximum weight that the towing vehicle is allowed to tow. 20-3 GLOSSARY PDI Speed Rating This is an inspection undertaken by the Retailer prior to handover to the customer. This is the maximum speed at which a tyre may be used, as marked on its sidewall. Pitch Stabiliser A designated area of a caravan site allocated for the use of one outfit. Most sites will be arranged with defined pitches. A safety device which helps to prevent instability, this is done by increasing the friction between the caravan hitch and the tow ball. Propane Steady Winder Gas used in colder conditions and is usually supplied in red cylinders. A handle for operating the corner steadies. RCD A form of spanner used to set nuts and bolts to a specified degree of tightness. It is recommended for adjustment of wheel fixings on caravans. Torque Wrench This is a residual current device and is part of the electrical system which will ‘trip’ if there is an electrical fault. Towing Limit Gas Regulator See manufacturer’s braked towing limit and manufacturer’s unbraked towing limit. Safety device fitted between the gas cylinder and the gas system of a caravan, which controls the pressure of gas being released from the cylinder. Towing Mirrors Additional rear vision mirrors added to a towing vehicle to provide a greater width of view to see past a caravan. Road Lights The external lights used while the vehicle is travelling. Train Weight Roof Lights - See Roof Vent. The maximum permissible combined weight of tow car and touring caravan. Roof Vent Is an opening unit in the ceiling which lets in ventilation and light, these vary in size, but the best ones will have integral blinds and flyscreens and are also called rooflights. Twin Axle Is a caravan with two pairs of wheels, on two axles which are located close together. These are usually the larger, heavier caravans, where the second axle helps carry the greater weight more easily, and also makes a longer caravan more stable to tow. See also single axle. Semi-Rigid Pipe work Is water pipes made of a semi rigid plastic and are infinitely preferable to cheaper convoluted piping which can act as a trap for germs and smells. User Payload Single Axle The weight of all items carried in the caravan. This is a caravan with a single pair of wheels on one axle. See also twin axle. U-Shaped Settee Usually a reference to seating that literally is ‘U’ shaped. Slats Sometimes used for beds and can improve ventilation to mattress cushions. Vehicle Kerb weight The weight of the tow car often indicated in the manufacturers specifications.. Space Heater This is a type of heating equipment for the living quarters. Modern units fitted offer gas and mainsoperation. 20-4 GLOSSARY VIN - Vehicle Identification Number This is a unique serial identification number for a vehicle. All Cars and motor caravans should carry a VIN. Caravans are not obliged to, but most of those sold in recent years in the UK do as a result of the CRiS voluntary registration scheme. Warranty Is the terms and conditions that spell out your rights with regard to servicing, repair or replacement of parts as provided by the manufacturer. Wild Camping Term used for staying overnight away from a campsite. Illegal in many countries, but permission may be granted by individual landowners. 20-5 GLOSSARY 20-6 SERVICE DOCUMENTS SERVICE DOCUMENTS TOURING CARAVANS - ANNUAL SERVICE RECORD In order to take full use of your warranty offered by The Explorer Group Limited it is essential that your caravan is serviced within the time scale laid down in the warranty terms and conditions. See Index Warranty Terms & Conditions. Whether you use your caravan for short journeys or for touring at home or abroad, regular servicing will help to ensure that you can enjoy it to the full. The Annual Service offered by your retailer will include the following work and it is our recommendation you have your caravan serviced to this standard annually, in accordance with the National Caravan Council recommendations. The retailer will complete the record in this guide to show the work has been carried out. SECTION (A) CHASSIS 5. Carpet 1. Brakes 6. Doors and drawers 2. Suspension 7. All hinges and catches 3. Axles and Hubs 8. Ventilators 4. Tyres and pressures 9. Water pumps 5. Wheeled nuts 10. Hoses and sink plugs 6. Towing hitch and reverse 11. Hot water system 7. Jockey wheel 12. Cold water system 8. Breakaway chain 13. Window hinges and stays 9. Corner steadies 14. Cassette toilet 10. Adjusted and lubricated 15. Shower 11. Fully operational 16. Shower tray SECTION (B) EXTERIOR 17. Central heating 1. Exterior panels 18. Damp test 2. Windows SECTION (D) ELECTRICAL 3, Rooflights 1. Reflectors 4. Entrance door/Door locks 2. All interior lights/Road lights 5. Wheel boxes 3. Water pump and switches 6. Mouldings 4. Refrigerator 7. Gas bottle and fairing 5. Distribution unit 8. Ventilators 6. Charging unit 9. Paintwork 7. Junction box/Strip 10. All seals, mouldings etc. 8. Wiring and supports 11. Damp test 9. Trailer connecting plug sockets 12. Striping etc. 10. Overall tests etc. SECTION (C) INTERIOR 11. Awning lights 1. Wall panels 12. Electronic ignition (hob) 2. Furniture 13. 230V system where applicable 3. Curtains/Blinds/Flyscreens 4. Mattresses (Continued) 21-1 SERVICE DOCUMENTS SECTION (E) GAS INSTALLATION SECTION (F) FINAL 1. Hotplate Road test 2. Refrigerator 3. Heater 4. Leak tested 5. Water heated 6. Fully operational CARE WARRANTY Your caravan is covered by the 3 year warranty, it is a condition of this warranty that a service and safety check is carried out by your caravan retailer at least once a year (12 months from the date of purchase) in accordance with the National Caravan Council recommendations. ANNUAL SERVICE RECORD CARAVAN MODEL ................................................................................................................................................. VEHICLE IDENTIFICATION NUMBER ...................................................................... YEAR ........................... 1st SERVICE 2nd SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 3rd SERVICE 4th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 21-2 SERVICE DOCUMENTS 5th SERVICE 6th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 7th SERVICE 8th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 9th SERVICE 10th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 11th SERVICE 12th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 21-3 SERVICE DOCUMENTS 13th SERVICE 14th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 15th SERVICE 16th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 17th SERVICE 18th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 19th SERVICE 20th SERVICE DATE: DATE: RETAILERS STAMP: RETAILERS STAMP: I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. I/We certify that an annual service has been carried out in accordance with the manufacturers’ and National Caravan Council recommendations. 21-4 INDEX INDEX Furniture ......................................... 11-2 Glass Fibre Reinforced Plastic (GRP) .......................................... 11-1 Interior Walls ................................. 11-2 Jacking .............................................. 11-5 Lubrication ...................................... 11-5 Seitz Windows ............................... 11-1 Shower Trays, Shower Room and Wash Basin Fittings .................. 11-2 Thetford Toilet ............................... 11-3 Truma Space Heater ..................... 11-3 Tyres ................................................. 11-4 Water Containers ......................... 11-2 Water Systems - Sterilization ..... 11-3 Window Blinds & Flyscreens ...... 11-1 Care of your caravan Changing a Wheel ......................... 11-4 Charging System ................................... 8-2 Code of Practice - Water Ingress .. 14-1 Conditions ...................................... 14-1 Customer Obligation ................... 14-1 Mains Electrics ............................... 14-1 Remedial Work .............................. 14-2 Spare Parts ...................................... 14-1 The Code ........................................ 14-1 Covers .................................................. 12-1 A Aerial .................................................... 9-22 Alarm .................................................... 9-23 Automatic Charging System ............... 8-2 B Battery Charger ................................. 9-11 Battery Installation ............................... 8-1 Battery Maintenance ............................ 8-1 Blinds .................................................... 9-18 BPW Intelligent Drive Control ...... 9-24 Breakaway Cable, use of ...................... 3-3 Bulb Ratings ........................................... 8-2 C Cables, checking .................................... 3-5 Caravan Construction - Main Components .............................. 15-1 Additional Fixings to Your Caravan Shell ............................. 15-1 Awning Channel ............................ 15-1 Body Shell ....................................... 15-1 BPW Chassis .................................. 15-1 Braking System .............................. 15-1 Front Panel and Gas Bottle Locker Lid .................................. 15-1 Windows ......................................... 15-1 Caravan Handling .................................. 4-1 Care of your Caravan ....................... 11-1 ABS Panels & Fittings ................... 11-1 Acrylic Windows ........................... 11-1 Carpets, Upholstery and Curtains ...................................... 11-2 Chassis Maintenance .................... 11-6 Chassis Mounted Spare Wheel Carrier ........................................ 11-4 Chassis Spare Parts ....................... 11-6 Cleaning of all Taps ........................ 11-2 Cooking Equipment ...................... 11-2 Exterior Cleaning .......................... 11-1 D Doors ................................................... 9-19 E Electrical Control Panels .................... 9-1 Electrical System ................................... 8-1 Electricity ................................................ 6-1 12v Systems ....................................... 6-1 Connecting To Mains Supply .......... 6-1 Disconnecting Mains Supply .......... 6-2 Generator/Charger ......................... 6-1 Mains Supply ...................................... 6-1 Overseas Electrical Connection ... 6-2 Power Supply Charger .................... 6-1 22-1 INDEX Entertainment System ...................... 9-22 Equipment List Odyssey ........................................... 16-1 Pitch, selecting ....................................... 5-1 Power Drain ....................................... 12-1 Pre-Tow Checklist ................................ 3-2 F R Fire Safety ............................................... 2-2 Fuses - all models ................................. 8-3 Radio/DVD .......................................... 9-22 Ramp ........................................................ 5-1 RCD ......................................................... 8-1 Refrigerator Thetford N112 LCD ....................... 9-4 Reversing ................................................ 4-1 Road Lights Odyssey ........................................... 17-3 Rooflights ............................................. 9-16 G Gas ........................................................... 6-3 Connection ........................................ 6-3 Hoses .................................................. 6-3 Regulator ............................................ 6-3 Gas Safety Advice ................................. 7-1 Generators / Charger .......................... 8-1 Glossary ............................................... 20-1 S Safety, general ........................................ 2-1 Security Additional Security ....................... 10-2 Anti-Wind Corner Steadies ....... 10-1 Caravan Theft ................................. 10-1 CRIS ................................................. 10-1 Electronic Tagging .......................... 10-2 Service Documents ........................... 21-1 Setting Off .............................................. 4-1 Site Regulations ..................................... 5-1 Smoke Detector ................................ 9-11 Space Heater Operation ..................... 9-9 230V Operation ............................... 9-9 Fan Operation ................................ 9-10 Gas ...................................................... 9-9 Gas Operation .................................. 9-9 Speed Limits ........................................... 4-1 Stabiliser - Hitch Head Operation .... 3-2 Storage Long Term & Winter ..................... 12-1 H Handbrake .............................................. 3-5 I Insulation ............................................. 15-1 Introduction ........................................... 1-1 L LCD TV ................................................ 9-22 Leveller Jack ........................................... 5-1 Levelling, front & back .......................... 5-1 Levelling, side to side ........................... 5-1 Loading .................................................... 3-1 M Mains Unit .............................................. 8-1 Microwave ........................................... 9-10 Model Year .............................................. 1-1 N T Nose Weight Indicator ........................ 3-1 Taps ....................................................... 9-18 Technical Specifications Elddis Odyssey ............................... 18-1 P Parking ..................................................... 5-1 22-2 INDEX Toilet Thetford C200 CWE ................... 9-12 Towing Weight Ratio ............................ 3-1 Tyres ..................................................... 11-4 U Uncoupling ............................................. 3-3 V Ventilation .............................................. 2-2 W Warranty ............................................. 13-1 3-Year Manufacturer’s Warranty 13-1 Conditions ...................................... 13-1 Years 1 - 3 ....................................... 13-1 Years 2 & 3 ..................................... 13-1 Water Heater Operation ................... 9-9 Gas Operation .................................. 9-9 Water System ........................................ 6-4 Connection ........................................ 6-4 Draining .............................................. 6-4 Wheel Changing ................................ 11-4 Windows ............................................. 9-17 Wiring Diagrams Odyssey ........................................... 17-2 22-3 INDEX © Designed and Printed by Preset Graphics. Tel: 01332 549278. (MY2009. Ref: 21059) 22-4 The Explorer Group Limited Delves Lane, Consett, Co. Durham DH8 7PE Telephone: 01207 699000 • Facsimile: 01207 699001 • www.explorer-group.co.uk All the illustrations and descriptive matter in this guide are intended to give a general idea of the caravan. Changing market and supply situations may prevent the manufacturer from maintaining the exact specifications and details in this handbook and we therefore reserve the right to alter specifications and materials as conditions demand. Retailers are independent of the manufacturer and have absolutely no authority to bind the manufacturer by any express or implied undertaking or representation.