Transcript
TRANSWORLD AQUATIC ENTERPRISES INC.
WWW.JBJLIGHTING.COM
TABLE OF CONTENTS Important Safety Instructions
3—5
TRINITY™ - PARTS PAGE
6—7
Dimensions
8
Introduction
9
Getting Started
10-11
Lighting
12-15
Maintenance Log
16-17
Maintenance Notes
18-19
2
WARNING To guard against injury, basic safety precautions should be observed, including the following:
READ ALL SAFETY INSTRUCTIONS BEFORE USE. DANGER To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt to repair yourself: return the appliance to an authorized service facility for service or discard the appliance. A. If the appliance falls into water, DON’T reach for it! First unplug it and then retrieve it. If the electrical components of the appliance get wet, unplug the appliance immediately. B. Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet. C. Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or if it is dropped or damaged in any manner. D. To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium stand and tank to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug. A “drip loop”, shown in the Figure at the right should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The ”drip loop” is that part of the cord below the level of the receptacle or the connector if an extension cord is used, to prevent water travel along the cord and coming in contact with the receptacle. (Continued on pg 4)
3
D. (Continued from pg 3)
If the plug or the receptacle do get wet, DON’T unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the appliance. Then unplug and examine for the presence of water in the receptacle. E. Close supervision is necessary when any appliance is used by or near children. F. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and etc. G. Always unplug an appliance from the outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank the cord to pull plug from the outlet. Grasp the plug and pull to disconnect H. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition. I. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing. J. Make sure an appliance mounted on a tank is securely installed before operating it. K. Read and observe all the important notices on the appliance. L. This Appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature. M. This appliance is intended FOR HOUSEHOLD USE ONLY.
4
CLEANING It is important to keep this hood appliance clean. Always unplug the appliance before performing maintenance or cleaning of the exterior of this hood. Wipe exposed surfaces carefully with a damp terrycloth to remove any dust or mineral deposits which may collect over time. Make sure all surfaces are dry before re-plugging into an electrical outlet. To prevent scratching the aquarium, use a damp terrycloth when cleaning. Never use algae scrapers, scouring pads, razor blades, glass cleaner or other such abrasives.
SERVICING In order to assure proper electrical connections and polarity, replacement parts and servicing should be performed only by a qualified electrician.
OPERATION Please carefully read the entire “Owner’s Manual” for proper operation procedures before proceeding with turning on this appliance and adding livestock such as fish, corals, and invertebrates.
SAVE THESE INSTRUCTIONS
5
PARTS EXPLODED VIEW & IDENTIFICATION
6
PART
Name
#
T5
1
ALUMINUM CASE—TOP
T5 T5
2 3
ALUMINUM CASE—FRONT SIDECAP—RIGHT
T5
4
SIDECAP—LEFT
T5
5
SWITCH
T5
6
POWER CORD—T5
T5
7
STRAIN RELIEF BUSHING
T5 T5
8 9
LEG STAND—HINGE LEG STAND—ARM SUPPORT
T5
10
LEG STAND—ARM SUPPORT
T5
11
LEG STAND—SCREW
T5
12
LED—FEMALE POWER CORD
T5
13
LED—STRAIN RELIEF BUSHING
T5 T5
14 15
T5—ELECTRONIC BALLAST FAN-12 VOLT CONVERTER
T5
16
FAN-CIRCUIT BOARD
T5
17
FAN-CIRCUIT BOARD TRAY
T5
18
COOLING FAN
T5
19
ALUMINUM CASE—GROMMET
T5
20
ALUMINUM CASE—REAR
T5
21
1 WATT LED
T5
22
LED—MOISTURE PROOF COVER
T5
23
T5—LAMP SOCKET
T5
24
T5– LAMP SOCKET TRAY
T5
25
T5-LAMP SOCKET TRAY
T5
26
T5-PARABOLIC REFLECTOR
T5
27
T5-HIGH OUTPUT LAMP
T5
28
SPLASH GUARD LENS
T5
29
LED -TRANSFORMER
7
DIMENSIONS Model # T5HO-24
24W x 4 + 1W x 2 Nite-Vu LEDs
Model # T5HO-39 39W x 4 + 1W x 3 Nite-Vu LEDs
Model # T5HO-48
54W x 4 + 1W x 4 Nite-Vu LEDs
8
INNOVATIVE DESIGN
Thank you for purchasing the TRINITY™ T5HO illumination system. TRINITY™ fixtures are offered in 24”, 36”, and 48” lengths. These low profile fixtures are compact and modern in style. Fixtures are intended for use above covered aquariums with Flip Top Stands. TRINTY™ fixtures are preinstalled with dual cooling fans and independent power cords for use with timers. AROUND THE CLOCK ILLUMINATION This sleek lighting fixture offers 24 hour photoperiod cycles that mimic sunrise, daylight, sunset, and moon lighting. T5 high output lamps are 5/8” diameter fluorescent tubes that are produced in higher wattage configurations to produce a tremendous of lumens for live corals and invertebrates. INDIVIDUAL PARABOLIC LAMP REFLECTORS TRINITY™ fixtures are equipped with individual lamp reflectors to maximize reflective efficiency.
Our highly efficient parabolic reflector encompasses each lamp for maximum light penetration for corals and invertebrates.
9
WARNING Do not plug into electrical outlet until all lamps are installed correctly REMOVING PROTECTIVE FILM OFF SPLASHGUARD LENS Locate the Sliding Tab on the right sidecap. Pull out Sliding Tab Gently slide out Splash Guard Lens REMOVING PROTECTIVE FILM OFF SPLASHGUARD LENS 1. Slide out Splash 1 Guard Lens
2. Peel off Protective Film off Splash Guard Lens
2
INSTALLING T5 LAMPS
1/4 Turn
Carefully align the bi-pins into the socket Rotate the lamp until it locks into socket
10
INSTALLING—FLIP TOP LEG STANDS
Your TRINTIY™ fixture includes our Flip-Top Leg Stands that raise the fixture for maximum reflection and allows the fixture to be raised back for routine maintenance and cleaning. The innovative design fits all glass and acrylic aquariums. A. Insert stands into the “Sliding Track” on the underside of the fixture and adjust to tank size. B. Tighten plastic screw to lock. C. Flip light fixture up and it will stay in the upright position .
11
TRINITY™ POWER CORDS & LAMP LAYOUT 1. Daylight Power Cord - Controls Rows 1 & 3 2. Dawn/Dusk Power Cord - Controls Rows 2 & 4 3. Nite Vu—LED Power Cord -Controls Moonlights
1.
2.
3.
10K DAYLIGHT 420nm ACTINIC 10K DAYLIGHT 460nm ACTINIC
NITE-VU LEDs
12
ROW 1 ROW 2 ROW 3 ROW 4
UTILIZING TIMERS FOR LIGHT CYCLES We recommend purchasing 2 grounded timers from your local hardware or electronics store for use with the lighting fixture. You will be able to automate sunrise/sunset and daylight photoperiods by simply adding these simple devices.
TURNING ON YOUR LIGHTING SYSTEM (Moonlights) Your TRINITY™ fixture is installed with 1 Watt Nite-Vu LED’s that simulate nocturnal cycles with very dim blue light that casts sparkling rays that shimmer for a more natural light cycle commonly found in nature. A. Connect the single female prong cable from the fixture to the small block transformer. We recommend always keeping this plugged into an electrical outlet without a timer. B. The Nite-Vu LED lighting is very dim not to disturb the night cycles of fish but just bright enough to watch their nocturnal behaviors. The Nite-Vu LED lighting is best seen when surrounding light is turned off in the room.
13
TURNING ON YOUR LIGHTING SYSTEM (DAWN/DUSK) Your TRINITY™ fixture is installed with (2) type of Actinic Lamps A. 420 Nanometer—Utilizes 03 phosphors to create a brilliant purple fluorescence for photosynthesis 420 nm
B. 460 Nanometer—Utilizes phosphors to produce a bright blue wavelength 460 nm
* Lamp should be inserted into Row 2 or 4 * We recommend that the timer be set to turn on 2 hours before the daylight starts and stay on 2 hours after the daylight turns off to simulate a sunrise/sunset effect
14
TURNING ON YOUR LIGHTING SYSTEM (DAYLIGHT) Your TRINITY™ fixture is installed with (2) daylight 10,000K Lamps. A. 10,000K— Simulates high intensity daylight for promoting zooxanthalle production. Produces a crisp white spectrum.
10,000K
* Lamps should be inserted into Rows 1 & 3 * We recommend the daylight lamps to be on for 6-8 hours per day. * Plug into a household timer for 6-8 hours of a day. Fans will simultaneously start to keep the hood at proper operating temperatures.
15
RECOMMENDED MAINTENANCE
MODEL DIMENSIONS T5 LAMP QTY
24W x 4
T5HO-24
39W x 4
T5HO-36
54W x 4
T5HO-48
BALLAST TYPE
AMPS/VOLTS
2300
12 Volt
9-12 Months
FULHAM –ELECTRONIC
0.56/120
9-12 Months
2300
12 Volt
9-12 Months
FULHAM-ELECTRONIC
1.15/120
1W x 4
9-12 Months
2300
12 Volt
9-12 Months
FULHAM—ELECTRONIC
1.15/120
T5 LAMP KELVIN
LIFE OF T5 LAMP
9-12 Months
1W x 3
DC-1000mA
(2) 10K DAYLIGHT (1) 420nm ACTINIC (1) 460nm ACTINIC
FAN VOLTAGE
1W x 2
DC-500mA
3 Years
(2) 10K DAYLIGHT (1) 420nm ACTINIC (1) 460nm ACTINIC
FAN RPM
DC 500mA
3 Years
(2) 10K DAYLIGHT (1) 420nm ACTINIC (1) 460nm ACTINIC
LED DRIVER POWER
3 Years
MOON LIGHT LED QTY
LIFE OF FAN
LIFE OF LED LIGHT
16
DATE
MAINTENANCE
17
18
19
TransWorld Aquatic Enterprises, Inc 3730 W. Century Blvd #3 Inglewood, CA 90303 Phone: (877) 374-9981
Visit us at www.jbjlighting.com
20
