Transcript
Jetstream® JetCraft User’s Guide Release 3.3 Document No. 1000-A2-GB21-10
November 2003
Copyright © 2003 Paradyne Corporation. All rights reserved. Printed in U.S.A.
Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773. Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Paradyne Corporation to notify any person of such revision or changes. Changes and enhancements to the product and to the information herein will be documented and issued as a new release to this manual.
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods:
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.) Telephone: Call our automated system to receive current information by fax or to speak with a company representative. —
Within the U.S.A., call 1-800-870-2221
—
Outside the U.S.A., call 1-727-530-2340
Document Feedback We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to
[email protected]. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.
Trademarks Jetstream is a registered trademark of Paradyne Corporation. All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.
A
November 2003
1000-A2-GB21-10
JetCraft Software License Agreement CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS. BY USING ANY OF THE JETCRAFT SOFTWARE, YOU AGREE TO BE BOUND BY THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, DO NOT USE OR INSTALL ANY OF THE SOFTWARE. IN SUCH EVENT, YOU MAY RETURN THE SOFTWARE TO THE SELLER OR TO PARADYNE (UNUSED) FOR A REFUND OF THE PRICE PAID. This Software License Agreement (“Agreement”) grants you certain license rights in connection with the Paradyne Corporation (“Paradyne”) JetCraft software and related documentation to be installed (the “Software”). Where third-party software is pre-installed into Paradyne hardware (“Third Party Software”) and a separate End User License Agreement (“Third Party EULA”) is included with the Paradyne hardware, Licensee agrees to comply with the terms and conditions of the Third Party EULA with respect to its use of the Third Party Software. 1. Grant of License Subject to the terms and conditions of this License, Paradyne hereby grants to Licensee, and Licensee hereby accepts from Paradyne, a personal, nonexclusive license to install, use and execute Software in machine readable object code form, on that number and type of stations or access ports for which a licensee fee has been paid, solely for Licensee’s use in connection with the use of Paradyne hardware or a Paradyne-compatible integrated access device (“IAD”). Licensee shall have the right to make a reasonable number of copies of the Software for backup purposes. This license shall continue unless and until terminated in accordance with Section 4 of this Agreement. 2. Proprietary Rights Notices Licensee agrees (a) to respect all confidentiality notices or legends placed upon the Software; (b) not to conceal from view any copyright, trademark or confidentiality notices placed on the Software media or on any output generated by the Software; and (c) to reproduce all copyright, trademark or confidentiality notices on all copies of the Software, or any portion thereof, made by Licensee as permitted hereunder. 3. Proprietary Rights Licensee acknowledges that Paradyne (and, as applicable, its licensor(s)) retains exclusive right, title and interest in and to the Software and all copies or portions thereof, including all intellectual property rights. By accepting this license, Licensee does not become the owner of the Software, but has the right to use the Software as outlined and limited in this Agreement. Licensee further acknowledges and agrees that the Software contains confidential information and trade secrets developed and acquired by Paradyne (and, as applicable, its licensor(s)) through the expenditure of a great deal of time and money. Accordingly, Licensee agrees to treat the Software as confidential and not to disclose all or any portion of the Software to any third party or entity, except as such disclosure may be necessary to Licensee’s employees and consultants in the course of their employment. To the extent permitted by applicable law, Licensee agrees not to modify, decompile, disassemble or otherwise reverse engineer the Software. Licensee further agrees not to lend, rent, lease, sublicense or otherwise transfer any copies of the Software or any portion thereof in any form to any person, except as permitted in Section 9 of this Agreement. Licensee will use its best efforts and take all reasonable steps to protect the Software and to prevent any unauthorized reproduction, publication, disclosure, or distribution of the Software or any portion thereof. 4. Term and Termination This Agreement is effective upon the earlier of (a) the installation of the Software by Licensee (including, but not limited to, loading the Software on a hard disk), or (b) acceptance of delivery of any Software by Licensee, and shall continue unless and until terminated in accordance with the provisions of this Section 4. This Agreement shall automatically terminate and Licensee shall lose its license rights hereunder if (i) Licensee transfers possession of the Software, any copy of the Software, or any portion or merged portion of the Software to another party, except as provided in Section 9, or (ii) violates the provisions of Section 3. Additionally, Paradyne shall be entitled to terminate this Agreement upon written notice to Licensee in the event that Licensee breaches any material obligation under this Agreement. Licensee shall be entitled to terminate this Agreement upon written notice given by Licensee to Paradyne. Within ten (10) days after termination of this Agreement, Licensee shall destroy all copies of the affected Software and related documentation, or any portion thereof, in any form, and shall certify such destruction upon the request of Paradyne.
1000-A2-GB21-10
November 2003
B
5. Limited Warranty and Disclaimer of Warranties The media upon which any Software is contained is warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date of delivery to Licensee (the “Warranty Period”). The entire liability of Paradyne (and, as applicable, its licensor(s)) and Licensee’s exclusive remedy for breach of the foregoing limited warranty shall be for Paradyne to replace any defective media which is returned to Paradyne during the Warranty Period. PARADYNE DOES NOT WARRANT THAT ANY SOFTWARE WILL OPERATE ERROR-FREE, WILL OPERATE UNINTERRUPTED IN YOUR OPERATING ENVIRONMENT, IS COMPATIBLE WITH ANY SOFTWARE OR HARWARE CONFIGURATION, OR IS FREE OF ERRORS OR “BUGS.” EXCEPT AS PROVIDED HEREIN, THE SOFTWARE IS PROVIDED “AS IS” AND PARADYNE MAKES NO WARRANTY, EXPRESS, IMPLIED, OR STATUTORY, WITH RESPECT TO THE SOFTWARE AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON-INFRINGEMENT. 6. Availability of Support No support (such as ongoing maintenance and delivery of upgrades) is provided for the Software under this Agreement. Any support for the Software must be purchased separately. 7. Intellectual Property Indemnification Paradyne shall defend or settle, at its own expense, any action brought against Licensee to the extent arising out of or based on any claim alleging that the unmodified Software or any portion thereof, as used within the scope of this Agreement, infringes or misappropriates any third-party rights in copyrights, patents, or trade secrets in the United States. Additionally, Paradyne shall pay any damages finally awarded against Licensee and attributable to such claim, or any costs of settlement to which Paradyne agrees; provided, that (a) Licensee gives prompt written notice of any such claim, demand, or action to Paradyne; (b) Licensee provides Paradyne with sole control of the defense and settlement thereof; and (c) Licensee reasonably cooperates with Paradyne in the defense or settlement thereof. In the event that any Software is held in such suit or proceeding to infringe or misappropriate such intellectual property right, and the use of the Software, or portion thereof, is enjoined, Paradyne shall, at its sole option and expense (i) procure for Licensee the right to continue using the Software, or portion thereof; (ii) replace the same with noninfringing programs of reasonably equivalent functionality; or (iii) accept return of the Software, or portion thereof. In the event that Paradyne accepts return of the Software, or portion thereof, Licensee shall receive a refund of that portion of any fee paid in connection with the license for such Software, or portion thereof. Paradyne assumes no liability hereunder for claims which result from the use or combination of the Software with other than Paradyne hardware or Paradyne-compatible IADs. THIS SECTION 7 SETS FORTH THE ENTIRE LIABILITY AND OBLIGATION OF PARADYNE AND LICENSEE’S SOLE REMEDY FOR ANY CLAIM OF INFRINGEMENT OR MISAPPROPRIATION OF PATENT, COPYRIGHT, TRADE SECRET OR OTHER INTELLECTUAL PROPERTY RIGHTS. 8. Limitation of Liability IN NO EVENT WILL PARADYNE (OR, AS APPLICABLE, ITS LICENSORS) BE LIABLE TO LICENSEE OR ANY OTHER PARTY FOR ANY CONSEQUENTIAL, INCIDENTAL, PUNITIVE, SPECIAL OR INDIRECT DAMAGES ARISING OUT OF THIS AGREEMENT OR THE USE OR INABILITY TO USE THE SOFTWARE, INCLUDING, BUT NOT LIMITED TO, ANY LOST PROFITS OR COST SAVINGS, EVEN IF PARADYNE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE PARADYNE LIABILITY TO LICENSEE, WHETHER BASED ON AN ACTION OR CLAIM IN CONTRACT OR TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE AND, TO THE EXTENT PERMITTED BY LAW, STRICT LIABILITY) OR OTHERWISE, ARISING OUT OF OR RELATED TO THIS AGREEMENT EXCEED THE AGGREGATE FEES PAID BY LICENSEE FOR THE SOFTWARE AS OF THE DATE SUCH ACTION OR CLAIM WAS FILED. 9. Transfer and Assignment Neither the licenses granted hereunder nor this Agreement (nor any portion of the Software) may be assigned or transferred by Licensee except in connection with the sale or transfer of the Paradyne hardware or Paradyne-compatible IAD with which the Software is used, and then only if (a) the entire Software and all copies thereof, and related documentation, are transferred; and (b) the transferee agrees to be bound by the terms of this Agreement.
C
November 2003
1000-A2-GB21-10
10. U.S. Government Restricted Rights The following terms shall apply where Licensee is an agency or unit of the U.S. government. a.
Units of the DoD. Use, duplication or disclosure by the government is subject to restrictions as set forth in paragraph (c)(1)(ii) of the Rights in technical Data and Computer Software clause at DFARS 252.227-7013. Paradyne Corporation, 8546 126th Avenue North, Largo, Florida 33773.
b.
Civilian agencies. Use, reproduction or disclosure is subject to restrictions as set forth in subparagraphs (a) through (d) of the Commercial Computer Software-Restricted Rights clause at FARS 52.227-19 and the limitations set forth in the Paradyne standard commercial agreement for this Software. Unpublished-rights reserved under the copyright laws of the United States.
11. Compliance with Laws and Payment of Taxes Licensee agrees to comply with all applicable laws in connection with its license and use of the Software. Licensee represents and warrants that it is authorized under applicable United States export laws and regulations to obtain and use the Software licensed hereunder and, and agrees that it will not export or re-export the Software in violation of those laws and regulations. Licensee shall be responsible for payment of all sales or use taxes, duties or other governmental assessments upon the license of the Software to Licensee (exclusive of taxes on the net income of Paradyne), and any property or other taxes assessed upon Licensee’s possession or use of the Software. 12. Miscellaneous In the event that any provision of this Agreement is found invalid or unenforceable pursuant to judicial decree or decision, the remainder of this Agreement shall remain valid and enforceable according to its terms. This Agreement shall be construed and enforced in accordance with the laws of the State of Florida, exclusive of its choice of law rules. The application of the United Nations Convention on the International Sale of Goods is expressly excluded. Any action or proceeding arising out of or related to this Agreement shall be brought in a state or federal court of competent jurisdiction located in the County of Pinellas, Florida and both parties hereby submit to the in personam jurisdiction of such courts for purposes of any such action or proceeding. Notwithstanding the foregoing, if Licensee resides outside the United States, any such action or proceeding shall be submitted to binding arbitration in Pinellas County, Florida, and the arbitration hearing shall be conducted in the English language and pursuant to the International Rules of the American Arbitration Association (as then in effect) and judgment on the award may be entered by any court of appropriate jurisdiction. This Agreement may not be modified, amended or altered except by a writing signed by a duly authorized representative of Paradyne and Licensee. No waiver of any provision of this Agreement or any right or obligation of either party shall be effective except pursuant to a writing signed by a duly authorized representative of Paradyne and Licensee. This Agreement constitutes the entire agreement between Paradyne and Licensee with respect to the transactions contemplated herein and supersedes any and all prior or contemporaneous oral or written communications with respect to the subject matter hereof.
1000-A2-GB21-10
November 2003
D
E
November 2003
1000-A2-GB21-10
Table of Contents
Preface Audience xv Organization xv Related Documents xvii New in This Release xvii Symbols xviii
Chapter 1
JetCraft Overview
JetCraft Features................................................................1-2 CPX-1000 Components ....................................................1-4 Craft Terminal....................................................................1-4
Chapter 2
JetCraft Installation
Preparing for JetCraft Installation ..................................2-1 Installing JetCraft .............................................................2-2 Starting JetCraft.................................................................2-8 Where to Go Next ...........................................................2-10 Re-connecting to JetCraft ...............................................2-10 Removing JetCraft .......................................................... 2-11
November 2003
i
Table of Contents
1000-A2-GB21-10
Chapter 3
JetCraft Basic Operations
The JetCraft Main Screen .................................................3-1 Menu Bar ......................................................................3-2 Toolbar Icons................................................................3-2 Tree View ......................................................................3-2 Map View .....................................................................3-4 Shelf View.....................................................................3-4 The Alarm Window ....................................................3-5 The Status Bar ..............................................................3-5 JetCraft Menus...................................................................3-6 The File Menu..............................................................3-6 The Configuration Menu ...........................................3-7 The Services Menu......................................................3-8 The Report Menu ........................................................3-9 The Help Menu............................................................3-9
Chapter 4
Administration and User Management
Understanding User Access Control..............................4-1 Changing a User Password .............................................4-2 Creating CPX Users .........................................................4-3 Modifying CPX Users ......................................................4-5 Deleting CPX User ...........................................................4-7 Reviewing CPX Users.......................................................4-7
Chapter 5
CPX-1000 Configuration
CPX-1000 Configuration Profile .....................................5-2 Modifying CPX-1000 Parameters .............................5-3 Reviewing CPX-1000 Parameters .............................5-5 Modifying IP Configuration............................................5-5 Configuring Global VCI Settings....................................5-7
ii
November 2003
1000-A2-GB21-10
Table of Contents
Setting CDV Value ............................................................5-9 Configuring CRC4 Setting .............................................5-10 Setting Clock Source ....................................................... 5-11 Refreshing the CPX-1000 Display ................................5-13
Chapter 6
Interface Groups Provisioning
Setting Up V5 Display ......................................................6-3 Creating V5.1 Interface Groups.......................................6-3 Creating V5.2 Interface Groups ......................................6-7 Deleting Interface Groups..............................................6-13 Restarting PSTN ..............................................................6-14 V5 Reprovisioning ..........................................................6-14 Adding Variants ..............................................................6-15 Modifying Active Variant ..............................................6-19 Verifying a Variant ..........................................................6-20 Deleting a Variant ...........................................................6-21 Switching Variants ..........................................................6-22 Adding E1 Links ............................................................6-23 Removing E1 Links ........................................................6-25 Performing E1 Link ID Check .......................................6-27 Changing E1 Link States ................................................6-27 Viewing E1 Link Status ..................................................6-30
Chapter 7
Protection Group Provisioning
Assigning Protection Group Members ..........................7-2 Swapping Protection Group Members ..........................7-4 Removing Protection Group Members..........................7-5
November 2003
iii
Table of Contents
1000-A2-GB21-10
Chapter 8
IAD Profiles and ISDN Port Templates Provisioning
Adding IAD Profiles ........................................................8-2 Modifying IAD Profiles....................................................8-3 Deleting IAD Profiles .......................................................8-5 ISDN Port Templates Summary......................................8-6 Creating ISDN Port Template..........................................8-7 Modifying ISDN Port Template ......................................8-9 Deleting ISDN Port Template........................................ 8-11
Chapter 9
IADs Provisioning
IADs ....................................................................................9-1 IAD Admin States .............................................................9-2 Creating IADs withV5.2 IG..............................................9-4 Creating IADs with V5.1 IG........................................... 9-11 Modifying IADs ..............................................................9-18 Deleting IADs ..................................................................9-21 Reviewing IADs ..............................................................9-23 Searching IADs by Fields ..............................................9-23
Chapter 10 Network Resource Manager Overview..........................................................................10-1 Provisioning.....................................................................10-2 Modifying a Network Resource..............................10-3 Deleting a Network Resource .................................10-3
Chapter 11 Alarms, Events, and Statistics Alarms Notification ........................................................ 11-1 CPX Alarms ..................................................................... 11-3
iv
November 2003
1000-A2-GB21-10
Table of Contents
Setting Alarm Polling Interval ...................................... 11-3 Statistics ............................................................................ 11-4 Statistics Summary.......................................................... 11-6 Accessing Network Protection Groups........................ 11-9 Accessing IADs ............................................................. 11-10 Accessing E1 Links ....................................................... 11-11 Graphing Statistics........................................................ 11-12
Chapter 12 CPX-1000 Maintenance and Services Backing Up CPX-1000 Database ...................................12-2 Restoring CPX-1000 Database .......................................12-3 Rebooting the CPX-1000 ...............................................12-4 Rebooting the MP or CP Card.......................................12-5 Setting the Clock .............................................................12-5 Switching CP Cards ........................................................12-7 Ensuring Redundancy .............................................12-8 Changing CP Card States.........................................12-9 Performing a CP Switchover ................................. 12-11 Hot Swapping................................................................ 12-11 Hot Swapping MP Card ........................................12-12 Hot Swapping CP and HSC Cards ......................12-13 Hot Swapping Line Cards .....................................12-14
Chapter 13 IAD Status and Maintenance Downloading IAD Software..........................................13-1 Automated IAD Software Download ..........................13-4 Storing IAD Software on the CPX-1000 .......................13-6 IAD Configuration Download .................................... 13-11 Automatic IAD Configuration Download .......... 13-11 Manual IAD Configuration Download ............... 13-11 Remote Restarting of IADs ..........................................13-14
November 2003
v
Table of Contents
1000-A2-GB21-10
Monitoring IAD Port Status ........................................13-17
Appendix A JetCraft Menu Map
Appendix B Statistics Definitions
Appendix C Alarm Summary
Index
vi
November 2003
Table of Figures
Figure 2–1. Figure 2–2. Figure 2–3. Figure 2–4. Figure 2–5. Figure 2–6. Figure 2–7. Figure 2–8. Figure 2–9. Figure 2–10. Figure 2–11. Figure 2–12. Figure 2–13. Figure 2–14. Figure 2–15. Figure 2–16. Figure 2–17. Figure 3–1. Figure 3–2. Figure 3–3. Figure 3–4. Figure 3–5. Figure 3–6. Figure 3–7. Figure 3–8. Figure 3–9. Figure 3–10. Figure 3–11. Figure 3–12.
November 2003
Welcome Screen .....................................................................2-2 Software Agreement License Screen ..................................2-3 Destination Folder Screen ....................................................2-3 Feature Selection Screen .......................................................2-4 Ready to Install Screen .........................................................2-5 Installation Summary Screen...............................................2-5 JetCraft Icon ...........................................................................2-6 JetCraft Properties Screen ....................................................2-6 Memory Tab with Selected Value .......................................2-7 JetCraft Login Dialog Box ....................................................2-8 Login Fail................................................................................2-9 JetCraft Main Screen .............................................................2-9 Add/Remove Programs Properties Screen .....................2-11 Uninstallation Complete Screen........................................2-12 Feature Selection Screen .....................................................2-12 Ready to Uninstall Screen ..................................................2-13 Uninstallation Summary Screen .......................................2-13 JetCraft Main Screen ............................................................3-2 Toolbar Icons .........................................................................3-2 Tree View ................................................................................3-3 Map View ...............................................................................3-4 Shelf View...............................................................................3-4 Alarm Window ......................................................................3-5 Status Bar................................................................................3-5 File Menu................................................................................3-6 Configuration Menu .............................................................3-7 Services Menu........................................................................3-8 Report Menu ..........................................................................3-9 The Help Menu......................................................................3-9
vii
1000-A2-GB21-10
Figure 4–1. Figure 4–2. Figure 4–3. Figure 4–4. Figure 4–5. Figure 4–6. Figure 4–7. Figure 5–1. Figure 5–2. Figure 5–3. Figure 5–4. Figure 5–5. Figure 5–6. Figure 5–7. Figure 5–8. Figure 6–1. Figure 6–2. Figure 6–3. Figure 6–4. Figure 6–5. Figure 6–6. Figure 6–7. Figure 6–8. Figure 6–9. Figure 6–10. Figure 6–11. Figure 6–12. Figure 6–13. Figure 6–14. Figure 6–15. Figure 6–16. Figure 6–17. Figure 6–18. Figure 6–19. Figure 6–20. Figure 6–21. Figure 6–22.
viii
Change Password Window .................................................4-2 Create User Window.............................................................4-3 Create User Window—Address Tab ..................................4-4 Create User Window—Contact Tab....................................4-4 Create User Window—Comment Tab................................4-5 Update User Informations Window ...................................4-5 Modify User Window ...........................................................4-6 CPX Configuration Window ...............................................5-4 CPX IP Configuration Window...........................................5-6 Global System Setting Window ..........................................5-7 CPX Configuration Window ...............................................5-9 E1 Port Configuration Window ........................................5-10 Clock Synch Window .........................................................5-11 Clock Synch Window with Clocks Unassigned..............5-12 Clock Synch Window with Clocks Assigned..................5-13 V5 Display Type Window ....................................................6-3 Interface Group Tabular View .............................................6-3 V5 Configuration Interface Group Panel...........................6-4 V5 Configuration Interface Group–E1 Link Assignment Panel65 V5 Configuration Interface Group–Data Link Panel .......6-6 Interface Group Tabular View with IGs Displayed..........6-7 Interface Group Tabular View .............................................6-7 V5 Configuration Interface Group Panel...........................6-8 V5 Configuration Interface Group–E1 Link Assignment Panel69 V5 Configuration Interface Group–Protection Group Panel6-10 V5 Configuration Interface Group–Data Link Panel .....6-11 Interface Group Tabular View with IGs Displayed........6-12 Tabular View with Interface Groups Displayed .............6-13 Variant Tabular View ..........................................................6-14 Variant Tabular View ..........................................................6-15 Create Variant Window ......................................................6-16 Create Variant Window—E1 Link Assignment Panel ...6-17 Create Variant Window—Protection Group Panel.........6-18 Modify Variant Window ....................................................6-19 Variant Tabular View ..........................................................6-20 Variant Tabular View ..........................................................6-21 Variant Tabular View ..........................................................6-22
November 2003
1000-A2-GB21-10
Figure 6–23. V5 Configuration Interface Group Panel.........................6-23 Figure 6–24. Modify Variant Window ....................................................6-24 Figure 6–25. V5 Configuration Interface Group–E1 Link Assignment Panel624 Figure 6–26. V5 Configuration Interface Group–E1 Link Assignment Panel626 Figure 6–27. Variant Tabular View ..........................................................6-27 Figure 6–28. Variant Tabular View ..........................................................6-28 Figure 6–29. E1 Link Configuration Window........................................6-28 Figure 6–30. Variant Tabular View ..........................................................6-30 Figure 6–31. E1 Link Status ......................................................................6-31 Figure 7–1. Network Protection Group Tabular View..........................7-2 Figure 7–2. Configuration for Network PG Window ...........................7-3 Figure 7–3. Protection Groups Displayed in Tabular View .................7-3 Figure 7–4. Protection Groups Displayed in Tabular View .................7-4 Figure 7–5. Protection Groups Displayed in Tabular View .................7-5 Figure 7–6. Configuration for Network PG Window ...........................7-5 Figure 8–1. Add IAD Profile Window ....................................................8-2 Figure 8–2. Update IAD Profile Window ...............................................8-4 Figure 8–3. Modify IAD Profile Window ...............................................8-4 Figure 8–4. Update IAD Profile Window ...............................................8-5 Figure 8–5. ISDN Port Template Creation Window .............................8-7 Figure 8–6. ISDN Port Template Manager Window .............................8-9 Figure 8–7. ISDN Port Template Modification Window ....................8-10 Figure 8–8. ISDN Port Template Manager Window ...........................8-11 Figure 9–1. IAD Installation .....................................................................9-1 Figure 9–2. IAD Creation Wizard–Introduction Screen .......................9-4 Figure 9–3. IAD Creation Wizard–Informational Screen .....................9-5 Figure 9–4. IAD Creation Wizard–IAD Selection Screen .....................9-5 Figure 9–5. IAD Creation Wizard–IG Selection Screen ........................9-6 Figure 9–6. IAD Creation Wizard–ATM PG Configuration Screen....9-6 Figure 9–7. IAD Creation Wizard–Reference Configuration Screen ..9-7 Figure 9–8. IAD Creation Wizard–Port Configuration Screen............9-8 Figure 9–9. IAD Creation Wizard–D Channel Assignment Screen ....9-9 Figure 9–10. IAD Creation Wizard–D Channel Assignment Screen ..9-10 Figure 9–11. IAD Creation Wizard–Introduction Screen .....................9-11 Figure 9–12. IAD Creation Wizard–Informational Screen ...................9-12 Figure 9–13. IAD Creation Wizard–IAD Profile Selection Window...9-12 Figure 9–14. IAD Creation Wizard–IG Selection Window ..................9-13
November 2003
ix
1000-A2-GB21-10
Figure 9–15. IAD Creation Wizard–ATM Protection Group Configuration Window9-13 Figure 9–16. IAD Creation Wizard–Reference Configuration Screen 9-14 Figure 9–17. IAD Creation Wizard–Port Configuration Window ......9-15 Figure 9–18. IAD Creation Wizard–B Channel Assignment Screen...9-16 Figure 9–19. IAD Creation Wizard–D Channel Assignment Screen ..9-17 Figure 9–20. IAD Creation Wizard–IAD Creation Summary Screen .9-18 Figure 9–21. IAD Configuration Manager Window .............................9-19 Figure 9–22. IAD Configuration Manager Window with IADs Displayed9-19 Figure 9–23. IAD Modification Window ................................................9-20 Figure 9–24. IAD Configuration Manager Window .............................9-21 Figure 9–25. IAD Configuration Manager Window with IADs Displayed9-22 Figure 9–26. Delete IAD Window............................................................9-22 Figure 9–27. View/Update IAD Window ..............................................9-24 Figure 10–1. Network Resource Management Window ......................10-2 Figure 10–2. Network Resource Manager Create Dialog.....................10-3 Figure 11–1. Alarm Window ....................................................................11-1 Figure 11–2. Alarmed Element in the Tree View...................................11-2 Figure 11–3. Alarm Polling Interval Configuration..............................11-3 Figure 11–4. Absolute and Relative Values............................................11-5 Figure 11–5. Network Protection Group Tabular View........................11-9 Figure 11–6. IAD Configuration Manager Window with IAD Displayed11-10 Figure 11–7. Variant Tabular View ........................................................ 11-11 Figure 11–8. Graphing Window ............................................................11-12 Figure 11–9. Sample Graph Window ....................................................11-13 Figure 11–10. Sample Table Window ......................................................11-14 Figure 12–1. Backup CPX Configuration Window ...............................12-2 Figure 12–2. Reboot CPX Configuration Window ................................12-3 Figure 12–3. Set CPX Time Window .......................................................12-6 Figure 12–4. Day Calendar .......................................................................12-6 Figure 12–5. Shelf View.............................................................................12-8 Figure 12–6. CP Card Configuration Window ......................................12-9 Figure 12–7. CP Card Configuration—Status Tab ..............................12-10 Figure 13–1. IAD Configuration Manager Window with IADs Displayed13-2 Figure 13–2. IAD Software Download dialog .......................................13-3 Figure 13–3. Global IAD Auto Download Status Screen .....................13-4 Figure 13–4. CPX IAD Auto Download Configuration Status............13-5 Figure 13–5. CPX-1000 Configuration Panel .........................................13-6 Figure 13–6. CPX-1000 IAD Firmware Manufacturer Panel ...............13-7
x
November 2003
1000-A2-GB21-10
Figure 13–7. Figure 13–8. Figure 13–9. Figure 13–10. Figure 13–11. Figure 13–12. Figure 13–13. Figure 13–14. Figure 13–15. Figure 13–16. Figure 13–17. Figure 13–18. Figure 13–19. Figure 13–20. Figure 13–21. Figure 13–22. Figure A–1.
November 2003
Location of IAD Firmware Panel ......................................13-8 IAD Firmware Manufacturer Confirmation Panel.........13-9 IAD Firmware Installation Panel ....................................13-10 IAD Firmware Installation Complete Panel..................13-10 IAD Configuration Manager Window ...........................13-12 IAD Configuration Manager Window with IADs Shown13-12 IAD Download Config Confirmation Window ............13-13 IAD Configuration Manager Window with IAD Config Download status13-14 IAD Configuration Manager Window ...........................13-15 IAD Configuration Manager Window with IADs Shown13-16 Restart IAD Dialog Box ....................................................13-16 IAD Restart Status Pop-up Window ..............................13-17 IAD Configuration Manager Window ...........................13-18 IAD Configuration Manager Window with IADs Displayed1319 IAD Modification Window ..............................................13-20 IAD Modification - Port Status Window .......................13-21 JetCraft Menu Map ............................................................. A-2
xi
1000-A2-GB21-10
xii
November 2003
List of Tables
November 2003
Table 1–1. Table 1–2. Table 2–1. Table 3–1. Table 4–1. Table 5–1. Table 6–1. Table 6–2. Table 7–1. Table 8–1. Table 9–1. Table 11–1. Table 11–2. Table B–1.
JetCraft Features ....................................................................1-2 Components Represented as Icons in JetCraft..................1-4 Hardware Requirements for JetCraft ................................2-2 Alarm Color and Alarm Severity .......................................3-5 User Access Level Summary ...............................................4-2 CPX-1000 Configurable Parameters ..................................5-2 Interface Group Configuration Parameters Summary ..6-2 E1 Link States ......................................................................6-28 Protection Group Summary.................................................7-1 ISDN Configurable Parameters Summary ........................8-6 Modifiable Options in Different Administrative States ..9-3 Alarm Severity by Color ....................................................11-2 Summary of Error and Performance Statistics ...............11-6 Error Statistics Definitions .................................................. 3-1
Table B–2.
Performance Statistics Definitions ..................................... 3-4
Table C–1.
Alarm Summary.................................................................. C-1
xiii
List of Tables
xiv
1000-A2-GB21-10
November 2003
Preface
The JetCraft User’s Guide provides detailed instructions for installing Jetstream craft interface terminal software on your PC. This guide also provides instructions to configure and provision a CPX-1000 Voice Services Platform using JetCraft.
Audience
The JetCraft User’s Guide is written for test and installation technicians and engineers who install and use the JetCraft software to test a CPX-1000.
Organization
The JetCraft User’s Guide is organized as follows:
November 2003
■
Chapter 1, JetCraft Overview, provides an overview of the CPX-1000 Voice Gateway and defines the hardware and software components and their functions. It also explains the role JetCraft plays in the initial setup of CPX-1000 equipment and its ongoing management.
■
Chapter 2, JetCraft Installation, provides instructions to install the JetCraft software on your Microsoft Windowsbased PC.
■
Chapter 3, JetCraft Basic Operations, describes component icons in the main screen, and how to use them.
■
Chapter 4, Administration and User Management, provides procedures provisioning CPX-1000 users.
■
Chapter 5, CPX-1000 Configuration, provides procedures to configure CPX-1000 and create users and CPX-1000 profiles.
■
Chapter 6, Interface Groups Provisioning, provides instructions to provision the Interface Groups.
■
Chapter 7, Protection Group Provisioning, provides instructions to provision the network Protection Group.
xv
Preface
xvi
1000-A2-GB21-10
■
Chapter 8, IAD Profiles and ISDN Port Templates Provisioning, provides instructions to provision IAD Profiles and ISDN port Templates.
■
Chapter 9, IADs Provisioning, provides instructions to provision IADs.
■
Chapter 10, Network Resource Manager, shows how to use the Network Resource Manager for Call Admission Control.
■
Chapter 11, Alarms, Events, and Statistics, describes JetCraft alarms and how to collect and graph error and performance statistics.
■
Chapter 12, CPX-1000 Maintenance and Services, provides instruction to perform routine maintenance.
■
Chapter 13, IAD Status and Maintenance, provides instructions to restart and monitor IADs.
■
Appendix A, JetCraft Menu Map, provides a linear, hierarchical overview of the tasks and sub-tasks associated with the JetCraft main window menu.
■
Appendix B, Statistics Definitions, provides definitions for statistics used in JetCraft.
■
Appendix C, Alarm Summary, provides a summary of event and error alarms.
■
Index
November 2003
1000-A2-GB21-10
Related Documents
New in This Release
Preface
■
CPX-1000 Voice Services Platform Introduction and Technical Description describes features and characteristics of the CPX-1000 Voice Services Platform equipment.
■
CPX-1000 Voice Services Platform Installation provides instructions to unpack, install, power-up, and test the CPX-1000 Voice Services Platform equipment.
■
CPX-1000 Voice Services Platform Service provides instructions to troubleshoot the CPX-1000 Voice Services Platform equipment.
Release 3.3 of JetCraft includes the following enhancements: Network Resource Management Automated IAD software download IAD configuration download Voice Quality Alarm
November 2003
xvii
Preface
Symbols
1000-A2-GB21-10
This document uses the following special symbol.
Voice/Data Interruption
This telephone symbol alerts you to the procedures that interrupt traffic.
Note Throughout this guide, the pointing finger highlights important information. Be sure to read this information before continuing.
xviii
November 2003
C
H
A
P
T
E
R
1
JetCraft Overview
JetCraft is primarily used by the central office (CO) craft personnel performing on-site management, including the installation and troubleshooting of CPX-1000. This chapter explains the role JetCraft plays in the initial setup of a CPX-1000 equipment and its ongoing management. This chapter includes these topics: JetCraft features (page 1-2) CPX-1000 components (page 1-4) Craft terminal (page 1-4)
A Java application, JetCraft uses a Graphical User Interface (GUI) to manage the CPX-1000 and its components, including configuring the CPX-1000 provisioning Interface Groups, and Protection Groups, and
IADs monitoring performance reporting alarms troubleshooting and maintenance
JetCraft also provides a security feature for controlling user access to the CPX-1000.
November 2003
1-1
JetCraft Overview
JetCraft Features
1000-A2-GB21-10
Table 1–1 lists the JetCraft features.
Table 1–1. JetCraft Features Features
Description
Configuration
At startup, CPX-1000 automatically discovers the following line cards: E-1 ATM (DS-3 and STM-1) EC ECAC
Country setting — each CPX has a country setting that allows for the customization of interface behavior to local norms (i.e., PSTN nationalization). CRC4 value — this feature allows the changing of the CRC property for each E1 provisioned on a V5 interface. It allows turning on or off the CRC value regardless of the state of the interface (i.e., Locked or Unlocked). For redundancy, the CPX-1000 supports primary/secondary and active/standby states for the following cards: Call Processors (CP) ATM (DS-3 and STM-1)
JetCraft also supports multiple VPI/VCI settings. Provisioning Interface Groups
JetCraft supports 16 V5.1 and 16 V5.2 Interface Groups. JetCraft also supports multiple variants.
1-2
Network Protection Groups
A Protection Group provides a logical mapping for two ports, where only one port is active at a time and another port is in a standby state. Up to four PGs can be provisioned.
ISDN Port Templates
It establishes a set of allowable parameters that can be used when setting up ISDN IADs.
IAD Profiles
JetCraft provides three default profiles.
IADs
JetCraft supports POTS and ISDN IADs and at least 2,000 IADs can be provisioned.
November 2003
1000-A2-GB21-10
JetCraft Overview
Table 1–1. JetCraft Features (Continued) Features
Description
Performance monitoring
JetCraft includes performance monitoring tools for routine maintenance and network capacity planning. When initiated, JetCraft collects information on equipment performance, such as total calls active on a CPX-1000 and virtual circuit bandwidth usage.
Alarms reporting
JetCraft includes an alarm sequence ID and a customizable alarm polling interval.
Security
JetCraft provides a default user ID (cpxuser) and password (cpxuser) and uses three user groups to control access to the CPX-1000.
Troubleshooting and maintenance
Switchover — JetCraft allows you to initiate a switchover, where two redundant cards exchange their active/standby states. Hot swap — JetCraft allows you to lock and remove resources associated with a line card without affecting the operation of the CPX-1000. Database backup and restore — the service provider can create CPX-1000 provisioning database files, use a File Transfer Protocol (FTP) application to transmit and receive the provisioning database files to and from a CPX-1000, and then restore the CPX-1000 provisioning database using the appropriate JetCraft menu option. In addition, you can maintain and upgrade the software for associated IADs through the JetCraft interface.
November 2003
1-3
JetCraft Overview
CPX-1000 Components
1000-A2-GB21-10
Table 1–2 lists and describes the icons used in JetCraft.
Table 1–2. Components Represented as Icons in JetCraft Icons
Description
CPX-1000 icon: the fundamental unit of installation. JetCraft accesses one CPX-1000 at a time. Shelf icon: up to 16 cards are installed in a CPX-1000 shelf.
Card icon: each card has configuration and status information.
Port icon: The physical ports on a card.
Protection Group (PG) manager icon: selects a PG for PG assignments, unassignments, and modification. V5 Interface Group (IG) icon: selects for V5.1 and V5.2 IG creation, deletion and modification. IAD icon: IADs are uniquely associated with a CPX-1000. You create voice path ATM Permanent Virtual Circuits (PVCs) when you create the IADs.
Craft Terminal
The JetCraft software runs on Windows 98 and 2000 or NT 4.0. A PC (or laptop) with the JetCraft software installed serves as a Craft terminal to the CPX-1000. The Craft terminal communicates with a CPX-1000 through an Ethernet connection using TCP/IP protocol. The physical connection can be local (through a Local Area Network (LAN) connection) or remote (through a Wide Area Network (WAN) connection).
1-4
November 2003
C
H
A
P
T
E
R
2
JetCraft Installation
This chapter provides instructions for installing and logging into JetCraft. This chapter includes these topics: Preparing the environment for installation (page 2-1) Installing JetCraft (page 2-2) Logging on to JetCraft (page 2-8) JetCraft road map (page 2-10) Removing earlier versions of JetCraft (page 2-11)
Preparing for JetCraft Installation
Before installation, make sure that the person performing the installation has administrator privileges. JetCraft requires the following: Computers running Windows 98 and NT Version 4, Service
Pack 5 or later Netscape Navigator, Release 4, or later or Internet Explorer,
Release 4.0.1, or later Table 2–1 lists the hardware requirements for running JetCraft.
November 2003
2-1
JetCraft Installation
1000-A2-GB21-10
Table 2–1. Hardware Requirements for JetCraft Hardware
Requirements
Craft Terminal
Pentium class 233 MHz processor or greater
RAM
48 MB
Virtual memory
100 MB
Storage (hard disk)
100 MB free disk space
CD-ROM drive
Accessible
Network
Ethernet NIC
Monitor
640 x 480 (VGA) or larger resolution preferred
Mouse and keyboard
Installing JetCraft Step 1
To install the JetCraft software:
Place the JetCraft application software CD into the CD-ROM drive. A screen appears, indicating the file extraction status. Then the Welcome screen appears (Figure 2–1).
Figure 2–1. Welcome Screen
2-2
November 2003
1000-A2-GB21-10
Step 2
JetCraft Installation
Click Next. The License Agreement screen appears (Figure 2–2).
Click here to continue
Figure 2–2. Software Agreement License Screen
Note At any time during this installation, you can click the Back button to review or correct the previous settings, then proceed from that point forward. Step 3
Click to select the I accept the terms of the license agreement checkbox, then click Next. The Destination Folder screen appears (Figure 2–3).
Figure 2–3. Destination Folder Screen
November 2003
2-3
JetCraft Installation
Step 4
1000-A2-GB21-10
Click Next to accept the default path: C:\Jetstream\. – Or – Type the directory path in the Destination folder field or click Change to navigate to where JetCraft will be installed. Then click Next. If a folder for JetCraft does not exist, a dialog box appears, asking if you want to create one. Click Yes. The Feature Selection screen appears, listing the installed features and their file sizes (Figure 2–4).
Figure 2–4. Feature Selection Screen
Note Make sure that both the Visibroker and JetCraft checkboxes are selected.
2-4
November 2003
1000-A2-GB21-10
Step 5
JetCraft Installation
Click Next. The Ready to Install screen appears, listing the features to be installed (Figure 2–5).
Figure 2–5. Ready to Install Screen Step 6
Click Install Now. A screen appears, showing the file extraction progress. After the files are extracted, the Installation Summary screen appears, listing the installed applications and their file sizes (Figure 2–6).
Figure 2–6. Installation Summary Screen
November 2003
2-5
JetCraft Installation
Step 7
1000-A2-GB21-10
Click Exit. The JetCraft icon (Figure 2–7) appears on your desktop.
Figure 2–7. JetCraft Icon If JetCraft is installed on a machine running Windows NT,
proceed to Step 12. If JetCraft is installed on a machine running Windows 98,
continue to the next step. Step 8
Right-click the JetCraft icon on the desktop to display the menu selection.
Step 9
Select Properties. The JetCraft Properties screen similar to Figure 2–8 appears.
Figure 2–8. JetCraft Properties Screen
2-6
November 2003
1000-A2-GB21-10
Step 10
JetCraft Installation
Select Memory. Use the drop-down list to select or type 32768 as the protected-mode memory, as shown in Figure 2–9.
Select or enter 32768
Figure 2–9. Memory Tab with Selected Value
November 2003
Step 11
Click OK to exit.
Step 12
Reboot the terminal.
2-7
JetCraft Installation
Starting JetCraft
1000-A2-GB21-10
JetCraft is not backward compatible. If you log in to a CPX-1000 running an earlier version, an error message appears, indicating the version of the CPX-1000 is unsupported. To start the JetCraft application: Step 1
Double-click the JetCraft icon on your desktop. The Login dialog box appears, displaying the default IP address (Figure 2–10).
Figure 2–10. JetCraft Login Dialog Box Step 2
Type the IP address of the CPX-1000 to which you are logging in the CPX IP field.
Note Once the IP address is entered, you don’t have to type it again until you change the CPX-1000 IP address. You can use the drop-down list to select the IP addresses.
2-8
Step 3
Type cpxuser (default user ID) in the User Id field.
Step 4
Type cpxuser (default password) in the Password field.
November 2003
1000-A2-GB21-10
Step 5
JetCraft Installation
Click OK. If the login fails, a message appears, describing the failure as
shown in Figure 2–11. Click Cancel to exit the login dialog box. Resolve the login problems, then repeat Step 1 to log in again.
Login Failure message
Figure 2–11. Login Fail When the login is successful, the JetCraft Main screen
similar to Figure 2–12 appears.
Figure 2–12. JetCraft Main Screen
November 2003
2-9
JetCraft Installation
Where to Go Next
1000-A2-GB21-10
You can learn about working with the JetCraft Main window (Chapter 3, JetCraft Basic Operations), or see an overview of all the menu options on the JetCraft Main window (Appendix A, JetCraft Menu Map). You can also use the JetCraft Main screen to configure the CPX-1000 shelf in the following order: Configuring CPX-1000 (Chapter 5) or
creating user access (Chapter 4) Provisioning Interface Groups (Chapter 6) Provisioning Protection Groups (Chapter 7) Provisioning IAD Profiles and ISDN Port Templates
(Chapter 8) Provisioning IADs (Chapter 9)
Re-connecting to JetCraft
JetCraft automatically times out after a period of inactivity. When the connection is lost, the following dialog box appears:
Click Re-login. Then type your user ID and password in their respective fields when the JetCraft Login window reappears.
2-10
November 2003
1000-A2-GB21-10
Removing JetCraft
JetCraft Installation
To remove an earlier version of JetCraft:
Step 1
Click the Start button > Settings > Control Panel.
Step 2
Double-click Add/Remove Programs. The Add/Remove Programs Properties screen appears.
Step 3
Select the JetCraft program, click Add/Remove as shown in Figure 2–13. A dialog box appears, asking if you want to delete the selected item.
Figure 2–13. Add/Remove Programs Properties Screen
November 2003
2-11
JetCraft Installation
Step 4
1000-A2-GB21-10
Click Yes. The Uninstallation Welcome screen appears (Figure 2–14).
Figure 2–14. Uninstallation Complete Screen Step 5
Click Next. The Feature Selection screen appears (Figure 2–15).
Figure 2–15. Feature Selection Screen
2-12
November 2003
1000-A2-GB21-10
Step 6
JetCraft Installation
Select the components you want to remove, then click Next. The Ready to Uninstall screen appears, listing the items to be deleted (Figure 2–16).
Figure 2–16. Ready to Uninstall Screen Step 7
Click Uninstall Now. The Uninstallation Summary screen appears (Figure 2–15) after the selected items are deleted.
Figure 2–17. Uninstallation Summary Screen
November 2003
Step 8
Click Exit. You are returned to the desktop.
Step 9
Close the Add/Remove Programs Properties screen.
2-13
JetCraft Installation
2-14
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
3
JetCraft Basic Operations
This chapter describes the JetCraft Main screen and different views from which it displays and menus. This chapter includes the following topics: The JetCraft Main screen (page 3-1) The JetCraft menus (page 3-6)
The JetCraft Main Screen
The JetCraft Main screen is an iconic representation of the CPX-1000 components it manages and the network entities with which it interfaces. The Main screen is divided into six sections (Figure 3–1): Menu bar Toolbar icons Tree View Map View (changes to Shelf View when the Shelf icon is
selected) Alarm window Status bar
You can access commands from the menu bar, toolbar icons, and by right-clicking objects in the Tree and Map views. For a complete listing of options available for each menu, refer to Appendix A, JetCraft Menu Map.
November 2003
3-1
JetCraft Basic Operations
1000-A2-GB21-10
Menu bar Toolbar Tree View
Map View
Alarm window Status bar
Figure 3–1. JetCraft Main Screen
Menu Bar
To use the JetCraft menus to perform an operation, make sure that you have access to this operation and that you have selected an appropriate CPX-1000 managed object for the operation. If your access to the operation is restricted, that menu selection is grayed out.
Toolbar Icons
There are seven icons on the toolbar (Figure 3–2). You can click an icon on the toolbar to open the menu selections (except the Alarm Summary icon). Click here to create V5.1 IGs
Click here to create IADs
Click here to perform IAD management functions
Click here to create V5.2 IGs
Click here to create IAD Profiles
Click here to update alarm summary Click here to create ISDN templates
Figure 3–2. Toolbar Icons
Tree View
3-2
The Tree View (Figure 3–3) provides a hierarchal view of the CPX-1000 cards. A plus sign (+) next to the card name indicates that there are ports assigned to that card. The name of the card includes the slot number and the name and number of the port. For example, the card labeled “02-E1” indicates that slot 2 contains a E-1 card.
November 2003
1000-A2-GB21-10
JetCraft Basic Operations
To expand and view the structure of the CPX-1000 cards, either double-click the Shelf icon on the Tree View or click the plus (+) key next to that icon. Click the minus (-) key to collapse the list. You can use the Tree View to find specific shelf or alarm information. Right-click an element icon and choose to view information about that element. CPX-1000 Shelf Card
Network Protection Group
V5 Interface Group IAD
Figure 3–3. Tree View
November 2003
3-3
JetCraft Basic Operations
Map View
1000-A2-GB21-10
Use the Map View (Figure 3–4) to select and view configuration, performance, and alarm information about the CPX-1000 and IADs. Right-click an element and choose configuration information.
Figure 3–4. Map View
Shelf View
Clicking the Shelf icon in the Tree View changes the Map View to Shelf View, displaying the cards installed on your CPX-1000. Use the Shelf View (Figure 3–5) to select and view configuration, performance, and alarm information about the CPX-1000 cards. Right-click a card and choose card configuration or report information. When Shelf View appears, resize the window to view the card names at the bottom of the window. For a description of individual cards, refer to CPX-1000 Voice Services Platform Installation.
Figure 3–5. Shelf View
3-4
November 2003
1000-A2-GB21-10
The Alarm Window
JetCraft Basic Operations
Alarms appear in the current alarm summary window as shown in Figure 3–6. Update the current alarm summary by clicking on the toolbar. You can sort and view alarm information by clicking any one of the Alarm window column headings. Click another column heading to change the sort order again.
Figure 3–6. Alarm Window Alarmed elements appear in the Tree View and Map View in a color relating to their alarm severity (Table 3–1). Alarms are also indicated by a large X on the affected object in the Tree View. The color of the X indicates the severity of the alarm (Chapter 11, Alarms, Events, and Statistics). Table 3–1. Alarm Color and Alarm Severity
The Status Bar
Alarm Severity
Color
Critical
red
Major
orange
Minor
yellow
The status bar displays alarm events and messages (Figure 3–7). Two colors indicate the type of message: blue for status and red for error.
Displayed message
CPX-1000 IP User ID
Figure 3–7. Status Bar
November 2003
3-5
JetCraft Basic Operations
JetCraft Menus
1000-A2-GB21-10
Four menus provide JetCraft operations: File menu Configuration menu Services menu Report menu
The Help menu provides a quick look-up of JetCraft procedures. It also provides an easy and convenient way to view information about JetCraft.
Note Operations displayed in some menus and icons selected in the Tree View are mutually inclusive; that is, an icon needs to be selected before the operation becomes available.
The File Menu
Use the File menu (Figure 3–8) to: refresh the CPX-1000 display after change exit JetCraft
Figure 3–8. File Menu
3-6
November 2003
1000-A2-GB21-10
The Configuration Menu
JetCraft Basic Operations
Use the Configuration menu (Figure 3–9) to: configure CPX cards and ports (Chapter 5, CPX-1000
Configuration) synchronize BITS clock (Chapter 5, CPX-1000
Configuration) create and modify Interface Groups and variants (Chapter 6,
Interface Groups Provisioning) create and manage ISDN port template (Chapter 8, IAD
Profiles and ISDN Port Templates Provisioning) create and manage IAD profiles (Chapter 8, IAD Profiles
and ISDN Port Templates Provisioning) swap between the primary and secondary members of the
Protection Group (Chapter 7, Protection Group Provisioning) create and manage IADs (Chapter 9, IADs Provisioning)
Shown with an IG selected
Shown with an IAD selected
Figure 3–9. Configuration Menu
November 2003
3-7
JetCraft Basic Operations
The Services Menu
1000-A2-GB21-10
Use the Services menu (Figure 3–10) to: back up and restore the CPX-1000 configuration
(Chapter 12, CPX-1000 Maintenance and Services) set the alarm polling interval (Chapter 11, Alarms, Events,
and Statistics) configure the CPX IP address (Chapter 5, CPX-1000
Configuration) change the CPX time (Chapter 12, CPX-1000 Maintenance
and Services) reboot the CPX-1000 (Chapter 12, CPX-1000 Maintenance
and Services) create a CPX user profile (Chapter 4, Administration and
User Management) change password (Chapter 4, Administration and User
Management) set up the global VCI value (Chapter 5, CPX-1000
Configuration)
Shown with an MP card selected
Shown with CPX-1000 selected
Figure 3–10. Services Menu
3-8
November 2003
1000-A2-GB21-10
The Report Menu
JetCraft Basic Operations
Use the Report menu (Figure 3–11) to generate: error graph statistics (Chapter 11, Alarms, Events, and
Statistics) performance graph statistics (Chapter 11, Alarms, Events,
and Statistics)
Figure 3–11. Report Menu
The Help Menu
Use the Help menu (Figure 3–12) to: launch the JetCraft Help view information about JetCraft
Figure 3–12. The Help Menu
November 2003
3-9
JetCraft Basic Operations
3-10
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
4
Administration and User Management This chapter provides instructions for provisioning users. These tasks include: Understanding user access control (page 4-1) Changing user passwords (page 4-2) Creating CPX users (page 4-3)
Although you can install JetCraft anytime, typically, you install the CPX-1000 and then the JetCraft software. After installation, use JetCraft to configure users and assign their access privileges. These users can access the CPX-1000 and create Interface Groups and IADs.
Understanding User Access Control
When you first start JetCraft, log in using the default user ID (cpxuser) and password (cpxuser). The default user ID belongs to an authorized user group that has access to all CPX operations. To limit CPX-1000 access, we recommend changing the default password as soon as possible. Each user group has a specific level of access and privilege, and users belonging to a specific group can only perform operations that are assigned to that group. Each user is given a password when the user group is created. Table 4–1 lists and defines the user access levels and their privileges.
November 2003
4-1
Administration and User Management
1000-A2-GB21-10
Table 4–1. User Access Level Summary Access Level
Privileges
Admin
This group has full access to all features of JetCraft, including changing other user’s passwords. They can create, modify, and delete all users, and can change JetCraft configuration.
Operations
This group can access JetCraft configuration but cannot create, modify, or delete all users. They can change their own password but not others.
Reports
This group can only view reports and statistics but cannot make or save any changes.
Changing a User Password Step 1
To change your own password or to change another user’s password (if you have Admin privileges): Select Change CPX Password from the Services menu. The Change Password window appears (Figure 4–1).
Figure 4–1. Change Password Window
4-2
Step 2
Type the old and new password.
Step 3
Type the new password again.
Step 4
Click OK to change the password.
November 2003
1000-A2-GB21-10
Creating CPX Users Step 1
Administration and User Management
To create a CPX user:
Select Create CPX User from the Services menu. The Create User window appears (Figure 4–2).
Figure 4–2. Create User Window Step 2
Enter the following information (up to 32 alphanumeric characters including spaces and punctuation) in their respective fields: ID—user’s login ID Name—user’s name Password—user’s password Retype—the user’s password Expiration Date—default is set to 10 years from the date
when this user is created (required Admin privilege to modify) Group—select Admin, Operations, or Reports from the
drop-down list
Note The Address, Contact, and Comment tabs are optional.
November 2003
4-3
Administration and User Management
Step 3
1000-A2-GB21-10
Click Address. The Address page appears.
Figure 4–3. Create User Window—Address Tab Step 4
Enter the address in their respective fields (up to 32 alphanumeric characters including spaces and punctuation).
Step 5
Select Contact. The Contact page appears.
Figure 4–4. Create User Window—Contact Tab Step 6
4-4
Enter the phone number, pager, and Email in their respective fields (up to 32 alphanumeric characters including spaces and punctuation).
November 2003
1000-A2-GB21-10
Step 7
Administration and User Management
Select Comments. The Comment page appears.
Figure 4–5. Create User Window—Comment Tab Step 8
Click anywhere in the Comment area and enter comments about the user.
Step 9
Click OK to create the CPX user.
Modifying CPX Users Step 1
Each user can modify personal user information. To modify other CPX user information, an Administrative privilege is required. Select CPX User Administration from the Services menu. The Update User Information window appears (Figure 4–6).
Figure 4–6. Update User Informations Window
November 2003
4-5
Administration and User Management
1000-A2-GB21-10
In addition to modifying user information, you can also perform the following tasks: add a new user (page 4-3) delete an existing user (page 4-7) Step 2
Select the user whose information you want to modify.
Step 3
Click Modify. The Modify User window appears (Figure 4–7).
Figure 4–7. Modify User Window Step 4
Modify the fields (if necessary) in any of the Modify User tabs (Creating CPX Users on page 4-3.)
Note The ID and Expiration Date fields cannot be modified. Step 5
4-6
Click OK to modify the CPX user.
November 2003
1000-A2-GB21-10
Deleting CPX User
To delete a CPX user (an Administrative privilege is required):
Step 1
Select the user you want to delete from the Update User Information window (Figure 4–6 on page 4-5).
Step 2
Click Delete. A message appears, asking if you want to delete the selected user.
Step 3
Click Yes. The user is deleted.
Reviewing CPX Users
November 2003
Administration and User Management
To review the newly created or existing CPX users, select CPX User Administration from the Services menu. The Update User Information window (Figure 4–6 on page 4-5) displays the CPX users information.
4-7
Administration and User Management
4-8
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
5
CPX-1000 Configuration
This chapter provides instruction for configuring the CPX-1000. It includes the following tasks: Modifying IP configuration (page 5-5) Configuring global VCI settings (page 5-7) Setting the CDV value (page 5-9) Configuring CRC4 setting (page 5-10) Setting clock source (page 5-11) Refreshing the CPX after modifications (page 5-13)
The CPX-1000 is shipped with the following default and a standard configuration profile that you use JetCraft to customize for a specific subscriber. IP address: 10.0.10.100 subnet mask: 255.255.255.0
If the CPX-1000 is configured, JetCraft automatically places the cards in service (i.e., unlocked state) when you log in. If the CPX-1000 has not been configured, you need to: ensure the CPX-1000 equipment is installed customize or modify the CPX-1000 profile configure the CPX-1000 for telephone service monitor equipment initialization for event messages and
alarms
November 2003
5-1
CPX-1000 Configuration
CPX-1000 Configuration Profile
1000-A2-GB21-10
The CPX-1000 is preprovisioned with a standard configuration profile. Since most of the CPX-1000 configuration parameters cannot be changed after Interface Groups and IADs are provisioned, modify the CPX-1000 configuration at startup. Table 5–1 lists the configuration parameters needed for configuring the CPX-1000 in JetCraft.
Table 5–1. CPX-1000 Configurable Parameters CPX Parameter
Description
ID
An identifier associated with the CPX-1000, consists of 4–16 alphanumeric characters (e.g., JET1). No spaces, underlined characters, etc. allowed.
Name
A name for the CPX-1000 that consists of up to 16 alphanumeric characters (e.g., JETSET). No spaces, underlined characters, etc. allowed. Use this name for differentiating CPX-1000s, error reporting, and when creating an IAD.
IP Address
The 32-bit Internet Protocol address assigned to the CPX-1000.
Default Gateway
The IP address that allows the CPX-1000 to be addressed over a LAN or WAN.
Subnet Mask
The 32-bit identifier that allows the IP address of the CPX-1000 to be used with multiple connections.
Administrative State
JetCraft administrative service-affecting state of CP cards and ports. Options are: Unlocked: Capable of service Locked: Restricted from service (card is in the shelf, but
JetCraft or JetVision administrators restricted it from service)
5-2
November 2003
1000-A2-GB21-10
CPX-1000 Configuration
Table 5–1. CPX-1000 Configurable Parameters (Continued) CPX Parameter
Description
Operational State
The operational state of the CPX-1000 cards and ports. Options are: Enabled Disabled
Country
Setting the country “personality” governs the following behaviors: V5 interface nationalizations: Country-specific functions
required on the V5 interface for particular countries. Cadence ringing tables: The CPX-1000 downloads country-
specific ringing tables to its attached IADs, when applicable. Hook-flash timings (e.g., Flash Hook, Register Recall):
Each country can have its own timer boundaries specified. Once set, the CPX-1000 remembers its country setting and modifies its behavior accordingly.
Modifying CPX-1000 Parameters
To modify the CPX-1000 parameters:
Step 1
Select
in the Tree View.
Step 2
Select Configure from the Configuration menu. – Or – Right-click
in the Map View and select Configure.
The CPX Configuration window appears (Figure 5–1).
November 2003
5-3
CPX-1000 Configuration
1000-A2-GB21-10
Figure 5–1. CPX Configuration Window
Note You can modify the Name, ID, and Country fields; other fields are read only.
Step 3
Enter your modification(s) between 4 to 16 alphanumeric characters (no spaces, underlines, or slashes). the ID field the Name field (the identifier used in the Map View and identifies which IADs belong to the CPX-1000) Warning
Changing the country setting requires rebooting the CPX-1000. Rebooting the CPX-1000 interrupts the maintenance or provisioning process; however, call processing is not affected.
Step 4
5-4
Select a country setting from the Country drop-down list. A dialog box appears, asking if you want to change the setting. (DEFAULT is a best-guess on the set of V5 customizations for all EU countries. No ringing cadences are specified, and the hookflash timings are a middle-ground selection.)
November 2003
1000-A2-GB21-10
CPX-1000 Configuration
Step 5
Click Yes. When the reboot process completes, the following dialog box appears.
Step 6
Click Re-login. Then type your user ID and password in their respective fields when the JetCraft Login window reappears.
Reviewing CPX-1000 Parameters
To review the CPX-1000 parameters:
Step 1
Select
in the Tree View.
Step 2
Select Configure from the Configuration menu. – Or – Right-click
in the Map View and select Configure.
The CPX Configuration window (Figure 5–1 on page 5-4) displays the name and the identifier of the CPX-1000 and other read-only information, such as default gateway, IP address, serial number, and subnet mask.
Modifying IP Configuration
To modify IP configuration, you need the following information: IP address Subnet mask Default Gateway
November 2003
Step 1
Select the MP card from the Tree View or Shelf View.
Step 2
Select IP Configuration from the Services menu. The CPX IP Configuration window appears (Figure 5–2).
5-5
CPX-1000 Configuration
1000-A2-GB21-10
Figure 5–2. CPX IP Configuration Window
Note You can modify the IP address only when the MP card is selected.
Step 3
Type the new IP address, subnet mask, and default gateway in the appropriate fields.
Step 4
Click OK. A dialog appears, asking you if you want to reboot the CPX-1000.
Warning
Rebooting the MP card interrupts the maintenance or provisioning process; however, call processing is not affected.
5-6
November 2003
1000-A2-GB21-10
Step 5
CPX-1000 Configuration
Click Yes. When the CPX-1000 reboots, your changes are accepted. If you click No, your changes will not take effect.
Note After you reboot the CPX-1000, we recommend that you exit and re-login to JetCraft.
Configuring Global VCI Settings
Changing the VCI value is available only to CPX-1000 Release 3.1 or later. If you have an earlier release, you can view but not change the value. The default value is 1024. You can change the VCI value only when there are no IADs provisioned to the CPX-1000. Warning
Changing the VCI value requires rebooting the CPX-1000. Rebooting the CPX-1000 drops all calls.
To set the VCI value: Step 1
Select Configure Global System from the Services menu. The Global System Setting window appears (Figure 5–3).
Figure 5–3. Global System Setting Window
November 2003
5-7
CPX-1000 Configuration
Step 2
1000-A2-GB21-10
Type the VCI value or select one from the drop-down list. Your options are 64, 128, 256, 512, 1024.
Note This value determines the number of VCIs allowed per VPI.
5-8
Step 3
Click OK. A dialog box appears, informing you that a reboot is required and asking if you want to continue with the update.
Step 4
Click OK. When the reboot process completes, the following dialog box appears.
Step 5
Click Re-login. Then type your user ID and password in their respective fields when the JetCraft Login window reappears.
November 2003
1000-A2-GB21-10
Setting CDV Value
CPX-1000 Configuration
Cell Delay Variation (CDV) is a QoS parameter that measures the time needed for each cell to travel over the Virtual Circuit (VC). The value expressed is in the microsecond (ms). The higher the CDV value, the less the calls allowed. To set the CDV value:
Step 1
Locate the CPX-1000 by clicking the group icon from the Tree View where the CPX-1000 resides.
Step 2
Click a CPX-1000 and expand the tree.
Step 3
Click the CPX-1000 icon from the Tree View.
Step 4
Select Configure from the Configuration menu. The CPX Configuration window appears (Figure 5–4).
Figure 5–4. CPX Configuration Window
November 2003
Step 5
Type the values between 1 – 60 in both the ATM and Frame Relay fields (default for ATM is 8 ms and frame relay is 28 ms).
Step 6
Click OK.
5-9
CPX-1000 Configuration
Configuring CRC4 Setting
1000-A2-GB21-10
You can change the CRC value for each E1 provisioned on a V5 interface regardless of the state of the interface (i.e., Locked or Unlocked). The default value is On. To set the CRC4 value:
Step 1
Click the Shelf icon and expand the tree by clicking the + sign.
Step 2
Expand the desired E1 card, and select the port to which you want to set the CRC4 value.
Step 3
Select Configure from the Configuration menu. – Or – Right-click the port icon, and select Configure from the popup menu. The Port Configuration window appears (Figure 5–5).
Figure 5–5. E1 Port Configuration Window
5-10
Step 4
Select the CRC4 value from its drop-down list.
Step 5
Click OK.
November 2003
1000-A2-GB21-10
Setting Clock Source
CPX-1000 Configuration
The clock source is derived from the V5 Interface Groups. There are 35 possible priorities. Priority 35 is reserved for system clock and is not user-configurable. When the revertive behavior is selected, it takes place across all priorities. For example, if priorities 1 and 2 lose the clock, priority 3 takes over and is actively driving the bus. When priority 1 regains its clock, then priority 1 will then take control of driving the bus. To assign priority of CPX clock source:
Step 1
Select in the Tree View, then select Clock Synch from the Configuration menu. – Or – Right-click
in the Map View and select Clock Synch.
The Clock Synch window similar to Figure 5–6 appears.
Figure 5–6. Clock Synch Window
November 2003
5-11
CPX-1000 Configuration
1000-A2-GB21-10
Notes The Priority and Status fields are read only. The number of clock source available is based on the number of Interface Groups you have configured on your CPX-1000.
Step 2
Select a row in which you want to remove a clock source.
Step 3
Remove the old clock source by double-clicking the Clock Source field and selecting the blank line. The clock source is moved to the Unassigned Clocks panel (Figure 5–7).
Figure 5–7. Clock Synch Window with Clocks Unassigned Step 4
5-12
Select a row in which you want to set a new clock source.
November 2003
1000-A2-GB21-10
Step 5
CPX-1000 Configuration
Double-click the Clock Source field, and select a new clock source. The selected clock source is moved from the Unassigned Clocks panel and is displayed in the Clock Source field (Figure 5–8).
Figure 5–8. Clock Synch Window with Clocks Assigned Step 6
Select a revertibility policy (default is Revertive).
Step 7
Click OK.
Refreshing the CPX-1000 Display
November 2003
To refresh the CPX-1000 display after you’ve made modifications, select Refresh CPX from the File menu. The CPX-1000 display is updated with your modifications, and the message Refreshing...Done appears in the status bar.
5-13
CPX-1000 Configuration
5-14
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
6
Interface Groups Provisioning This chapter provides instructions to provision the Interface Groups. This chapter includes these tasks: Setting up V5 Display (page 6-3) Creating V5.1 Interface Groups (page 6-3) Creating V5.2 Interface Groups (page 6-7) Deleting Interface Groups (page 6-13) Restarting PSTN (page 6-14) Adding variants (page 6-15) Modifying variants (page 6-19) Verifying variants (page 6-20) Deleting variants (page 6-21) Switching variants (page 6-22) Adding E1 links (page 6-23) Removing E1 links (page 6-25) Performing E1 link ID check (page 6-27) Changing E1 link states (page 6-27) Viewing E1 link status (page 6-30)
V5.1 supports a single E1 link. V5.2 supports up to 16 E1 links, with signaling protection for all protocol for all protocol stacks and user signaling data, POTS, and ISDN BRI. V5.2 signaling protection is configured using protection groups. Protection Group 1 is used to configure internal protocols for all V5 interfaces. Optionally, Protection Group 2 is used when additional protected signaling bandwidth is required (typically for ISDN subscribers). POTS PSTN, and ISDN BRI signaling can be provisioned against either PG1, PG2 or directly on a physical DS0. JetCraft supports 16 V5.2 and 16 V5.1 Interface Groups for each CPX-1000.
November 2003
6-1
Interface Groups Provisioning
1000-A2-GB21-10
Table 6–1 lists the parameters you will need to configure the Interface Group.
Table 6–1. Interface Group Configuration Parameters Summary Parameters
Description
Name
The Interface Group name. The name is used for error reporting and to identify the interface group and assign subscribers.
Edition
Options are 1st edition and 2nd edition as defined by ETSI and ITU specifications.
Accelerated Alignment
This is a protocol feature of the V5.2 2nd edition specification. Some LE vendors offer this optional feature on their 1st edition compliant interfaces. Refer to your LE switch documentation and configuration for more information.
LE ID
This is a unique identifier for the interface defined on the LE. This number must match the number used in provisioning the LE side of the interface.
Variant Number
This number differentiates the provisioning data set from others and is uniquely applied to the provisioning data set being used. One Interface Group can have multiple variant data sets as information is updated. The variant number ranges between 0 to 127.
Switch Model
The host switch model (e.g., TDX, Nortel Networks DMS, Siemens EWSD).
Switch Name
This is the name of the switch (this data is used for reference purpose).
Admin State
Options are: Locked (out of service) Unlocked (in service) Shutting Down
Operational State
Options are: Enabled Disabled
6-2
November 2003
1000-A2-GB21-10
Setting Up V5 Display
Interface Groups Provisioning
By default, the LE IDs in V5 IGs are displayed in a decimal notation. To change it to the hexidecimal display:
Step 1
Click
in the Tree View.
Step 2
Select V5 Display Configuration from the Services menu. The V5 Display Type window appears (Figure 6–1).
Figure 6–1. V5 Display Type Window Step 3
Creating V5.1 Interface Groups Step 1
Click to select your preference, and click OK.
To create a V5.1 Interface Group:
Click on the Tree View, the right-hand pane changes to the Interface Group tabular view (Figure 6–2).
Figure 6–2. Interface Group Tabular View
November 2003
6-3
Interface Groups Provisioning
Step 2
1000-A2-GB21-10
Select Create V5.1 IG from the Configuration menu. – Or – Right-click on the Tree View and select Create V5.1 IG from the popup menu. – Or – Click
on the toolbar.
The V5 Configuration Interface Group panel appears (Figure 6–3).
Figure 6–3. V5 Configuration Interface Group Panel Step 3
6-4
Type a name up to 32 alphanumeric characters (including spaces and/or hyphens) for the Interface Group in the IG Name field.
November 2003
1000-A2-GB21-10
Step 4
Interface Groups Provisioning
Type or Select the values for the following IG parameters from the associated drop-down lists. (See Table 6–1 on page 6-2 for a description of each parameter.) Edition Accelerated Alignment LE ID Variant Switch Model Switch Name
Step 5
Click the E1 Link Assignment tab. The E1 Link Assignment panel appears (Figure 6–4).
Figure 6–4. V5 Configuration Interface Group–E1 Link Assignment Panel Step 6
November 2003
Assign the E1 link by selecting the card/port, then clicking the > button to move it to the Link # field.
6-5
Interface Groups Provisioning
1000-A2-GB21-10
Step 7
Type the link identifier in the range of 0 to 255 in the Link ID field.
Step 8
Click the Data Link tab. The Data Link panel similar to Figure 6–5 appears.
Figure 6–5. V5 Configuration Interface Group–Data Link Panel
Note The identifier in the ID field is automatically assigned when an E1 is assigned.
6-6
Step 9
Review the information. As necessary, change the PSTN channel to a different physical channel by clicking the associated fields to bring up the popup menu.
Step 10
Click OK to return to the Main screen.
November 2003
1000-A2-GB21-10
Step 11
Interface Groups Provisioning
Click Refresh CPX from the File Menu. The newly created IGs display in the Interface Groups tabular view (Figure 6–6).
Figure 6–6. Interface Group Tabular View with IGs Displayed
Creating V5.2 Interface Groups Step 1
To create a V5.2 Interface Group:
Click on the Tree View, the right-hand pane changes to the Interface Group tabular view (Figure 6–7).
Figure 6–7. Interface Group Tabular View Step 2
Select Create V5.2 IG from the Configuration menu. – Or – Right-click on the Tree View and select Create V5.2 IG from the popup menu. – Or – Click
November 2003
on the toolbar.
6-7
Interface Groups Provisioning
1000-A2-GB21-10
The V5 Configuration Interface Group panel appears (Figure 6–8).
Figure 6–8. V5 Configuration Interface Group Panel Step 3
Type a name up to 32 alphanumeric characters (including spaces and/or hyphens) for the Interface Group in the IG Name field.
Step 4
Type or Select the values for the following IG parameters from the associated drop-down lists. Edition Accelerated Alignment LE ID Variant Switch Model Switch Name
6-8
November 2003
1000-A2-GB21-10
Step 5
Interface Groups Provisioning
Click the E1 Link Assignment tab. The E1 Link Assignment panel appears (Figure 6–9).
Figure 6–9. V5 Configuration Interface Group–E1 Link Assignment Panel Step 6
Assign the E1 link by selecting the card/port, then clicking the > button to move it to the Link # field.
Note To select multiple port assignments, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select the port assignments in a random order.
Step 7
November 2003
Type a link identifier in the range of 0 to 255 in the Link ID field.
6-9
Interface Groups Provisioning
Step 8
1000-A2-GB21-10
Click the Protection Group tab. The Protection Group panel appears (Figure 6–10).
Note The Protection Group tab is enabled when you complete at least two E1 link assignments.
Figure 6–10. V5 Configuration Interface Group– Protection Group Panel
6-10
Step 9
Assign the primary link number to the Protection Group 1 by highlighting the link#/Time Slot area (must be 16), then clicking the > button to move it to the associated fields.
Step 10
Repeat Step 9 for the secondary link number.
Step 11
Assign the logical channel to the primary link.
Step 12
Repeat Step 9 for the secondary link number assignment.
November 2003
1000-A2-GB21-10
Step 13
Interface Groups Provisioning
Repeat Step 9 and Step 11 to assign the primary and secondary link information to the Protection Group 2 Active.
Note The Protection Group 2 is enabled when you highlight the link#/Time Slot area (15), then click the > button.
Step 14
Repeat Step 9 to assign the link information to the Protection Group 2 Standby.
Step 15
Click the Data Link tab. The Data Link panel appears (Figure 6–11). Click here to bring up the drop-down list
Figure 6–11. V5 Configuration Interface Group–Data Link Panel
November 2003
6-11
Interface Groups Provisioning
Step 16
1000-A2-GB21-10
Review the information. As necessary, change the channel type by right-clicking the PSTN-C Channel Type field to bring up the drop-down list.
Notes When the channel type is changed, other fields (i.e., ID and Time Slot) are updated to reflect the changes. The ID field refers to the logical channel ID.
Step 17
Click OK to return to the Main screen.
Step 18
Click Refresh CPX from the File Menu. The newly created IGs display in the Interface Group tabular view (Figure 6–12).
Figure 6–12. Interface Group Tabular View with IGs Displayed
Note To modify the E1 link and protection group parameters, refer to Modifying Active Variant on page 6-19.
6-12
November 2003
1000-A2-GB21-10
Deleting Interface Groups Step 1
Interface Groups Provisioning
To delete an Interface Group:
Click on the Tree View, the right-hand pane changes to the Interface Group tabular view (Figure 6–13).
Figure 6–13. Tabular View with Interface Groups Displayed Step 2
Click the desired Interface Group icon on the Tree View, and select Delete IG from the Configuration menu. – Or – Right-click the desired Interface Group icon on the Tree View, and select Delete IG from the popup menu. – Or – Right-click the highlighted selection on the tabular view and select Delete IG from the popup menu. A confirmation dialog box appears, asking if you want to delete the selected IG.
Note You can only delete an Interface Groups that are not associated with IADs.
November 2003
Step 3
Click Yes to delete the Interface Group.
Step 4
Select Refresh CPX from the File menu to update the changes.
6-13
Interface Groups Provisioning
Restarting PSTN Step 1
1000-A2-GB21-10
To restart the V5 Interface Groups:
Click the desired on the Tree View, the right-hand pane changes to the variant tabular view (Figure 6–22).
Figure 6–14. Variant Tabular View Step 2
Select PSTN Restart from the Configuration menu. – Or – Right-click the selected on the Tree View and select PSTN Restart from the popup menu.
V5 Reprovisioning
A provisioning variant refers to the provisioning datafill for an interface. Reprovisioning enables a service provider to configure multiple variants at a time. The variant in use at a given time is the active variant, while others are referred to as the standby variants. The active variant can be manually switched to standby; however, the standby must be previously provisioned. Subscriber datafill (i.e., IADs and ports) remains unchanged between variants. Variant consists of a variant ID, E1 links, protection information, and data link configuration. Because ISDN ports are provisioned with data channel, ISDN subscribers on V5.2 with more than one E1 can use logical channels only.
6-14
November 2003
1000-A2-GB21-10
Interface Groups Provisioning
When working with variants, the following restrictions apply: V5.1 and V5.2 with a single E1 do not support multiple
variants. ISDN subscribers on V5.2 with more than one E1 can use
logical channels only. V5 IG must have only one active variant, but it may contain
one or multiple standby variants. The only consistency check required across different variants is that logical channels carrying ISDN subscriber data be present in all variants. You may assign the same logical channel to different physical channels in different variants. Only the logical channel ID is needed to match the one used for the subscribers.
Adding Variants
The first variant is created when you first created the IG, and that variant is the active one until you switch it. To create a variant: Step 1
Click the desired Interface Group on the Tree View, the righthand pane changes to the variant tabular view (Figure 6–15).
Figure 6–15. Variant Tabular View Step 2
Select Create Variant from the Configuration menu. – Or – Right-click the selected on the Tree View and select Create Variant from the popup menu.
November 2003
6-15
Interface Groups Provisioning
1000-A2-GB21-10
The Create Variant window appears (Figure 6–16).
Figure 6–16. Create Variant Window
6-16
Step 3
Type the variant number between 0 to 127 in the Variant field.
Step 4
Click the E1 Link Assignment tab. The E1 Link Assignment panel appears (Figure 6–17).
November 2003
1000-A2-GB21-10
Interface Groups Provisioning
Figure 6–17. Create Variant Window—E1 Link Assignment Panel Step 5
Assign the E1 links by highlighting the Card/Port area, then clicking the > button to move it to the Link # area.
Note To select multiple port assignments, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select the port assignments in a random order.
November 2003
6-17
Interface Groups Provisioning
1000-A2-GB21-10
Step 6
Type a link identifier in the range of 0 to 255 in the Link ID field.
Step 7
Click the Protection Group tab. The Protection Group panel appears (Step 6–18).
Note The Protection Group tab is enabled when you complete at least two E1 link assignments.
Figure 6–18. Create Variant Window—Protection Group Panel
6-18
Step 8
Assign the primary link number to the Protection Group 1 by highlighting the link#/Time Slot area (must be 16), then clicking the > button to move it to the associated fields.
Step 9
Repeat Step 8 for the secondary link number.
Step 10
Assign the logical channel to the primary link.
Step 11
Repeat Step 8 for the secondary link number assignment.
November 2003
1000-A2-GB21-10
Step 12
Interface Groups Provisioning
Repeat Step 8 and Step 10 to assign the primary and secondary link information to the Protection Group 2 Active.
Note The Protection Group 2 is enabled when you highlight the link#/Time Slot area (15), then click the > button.
Step 13
Repeat Step 8 to assign the link information to the Protection Group 2 Standby.
Step 14
Select Refresh CPX from the File menu to update the changes.
Modifying Active Variant Step 1
To modify an active variant:
Right-click the desired active variant on the Tree View, and select Modify Variant. The Modify Variant window appears (Figure 6–19).
Figure 6–19. Modify Variant Window
November 2003
6-19
Interface Groups Provisioning
Step 2
1000-A2-GB21-10
Modify the lighted fields, then click the appropriate tab to modify other fields, if necessary.
Note Fields that cannot be modified are grayed out. Step 3
Click OK to return to the Main screen.
Step 4
Select Refresh CPX from the File menu to update the changes.
Verifying a Variant Step 1
To verify a variant:
Click the desired variant on the Tree View, the right-hand pane changes to the variant tabular view (Figure 6–15).
Figure 6–20. Variant Tabular View Step 2
Select Verify Variant from the Configuration menu. – Or – Right-click the selected on the Tree View and select Verify Variant from the popup menu. The following dialog box appears:
The result displays here
6-20
November 2003
1000-A2-GB21-10
Interface Groups Provisioning
Step 3
Type the variant ID you want to verify.
Step 4
Observe the status bar of the dialog box where the result of the verification is displayed.
Deleting a Variant Note You will be unable to delete a variant if it is the only one in that Interface Group.
To delete a variant: Step 1
Click the desired variant on the Tree View, the right-hand pane changes to the variant tabular view (Figure 6–21).
Figure 6–21. Variant Tabular View Step 2
Select Delete Variant from the Configuration menu. – Or – Right-click the selected Variant icon on the Tree View and select Delete Variant from the popup menu. A dialog box appears, asking if you want to delete the selected variant.
November 2003
Step 3
Click Yes.
Step 4
Select Refresh CPX from the File menu to update the changes.
6-21
Interface Groups Provisioning
1000-A2-GB21-10
Switching Variants Voice/Data Interruption
Active calls are dropped over a variant switching.
To switch from a standby variant: Step 1
Click the desired variant on the Tree View, the right-hand pane changes to the variant tabular view (Figure 6–22).
Figure 6–22. Variant Tabular View Step 2
Click the standby variant (shown in blue) and select Switch Variant from the Configuration menu. – Or – Right-click the standby variant icon on the Tree View and select Switch Variant from the popup menu. A dialog box appears, asking if you want to switch from the selected variant.
6-22
Step 3
Click Yes.
Step 4
Select Refresh CPX from the File menu to update the changes.
November 2003
1000-A2-GB21-10
Adding E1 Links
Interface Groups Provisioning
Adding E1 links can be done through Interface Groups and active variants. You cannot add links to V5.1 IG or to V5.2 IG that is configured with a single link. To add E1 links:
Step 1
Choose your method to add E1 links. Click the desired Interface Group icon on the Tree View, and
select the IG to which you want to add link. Then select Modify IG from the Configuration menu, or right-click the highlighted selection on the tabular view and select Modify IG from the popup menu. The V5 Configuration Interface Group panel similar to Figure 6–23 appears. Right-click the desired active variant on the Tree View, and
select Modify Variant. The Modify Variant window appears (Figure 6–24).
Figure 6–23. V5 Configuration Interface Group Panel
November 2003
6-23
Interface Groups Provisioning
1000-A2-GB21-10
Figure 6–24. Modify Variant Window Step 2
Click the E1 Link Assignment tab. The E1 Link Assignment panel appears (Figure 6–25).
Figure 6–25. V5 Configuration Interface Group–E1 Link Assignment Panel
6-24
November 2003
1000-A2-GB21-10
Step 3
Interface Groups Provisioning
Assign the E1 link by selecting the card/port, then clicking the > button to move it to the Link # field.
Note To select multiple port assignments, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select the port assignments in a random order.
Step 4
Type a link identifier in the range of 0 to 255 in the Link ID field.
Step 5
Click OK to return to the Main screen.
Step 6
Select Refresh CPX from the File menu to update the changes.
Removing E1 Links
Removing E1 links can be done through Interface Groups and active variants. You can remove E1 links only when the links are not configured for protection or bearer traffic. You cannot remove a link when V5.2 IG is configured with a single link.
Note Because V5.1 contains a single link, that link cannot be removed.
To remove E1 links: Step 1
Expand the desired CPX-1000 from the Tree View.
Step 2
Choose your method to remove E1 links. Click the desired Interface Group icon on the Tree View, and
select the IG to which you want to add link. Then select Modify IG from the Configuration menu, or right-click the highlighted selection on the tabular view and select Modify IG from the popup menu. The V5 Configuration Interface Group panel similar to Figure 6–23 on page 6-23 appears.
November 2003
6-25
Interface Groups Provisioning
1000-A2-GB21-10
Right-click the desired active variant on the Tree View, and
select Modify Variant. The Modify Variant window appears (Figure 6–24 on page 6-24). Step 3
Click the E1 Link Assignment tab. The E1 Link Assignment panel appears (Figure 6–9).
Figure 6–26. V5 Configuration Interface Group–E1 Link Assignment Panel Step 4
Click to highlight the Link #, then click the < button to move it to the Card/Port area.
Note To select multiple port assignments, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select the port assignments in a random order.
6-26
Step 5
Click OK to return to the Main screen.
Step 6
Select Refresh CPX from the File menu to update the changes.
November 2003
1000-A2-GB21-10
Performing E1 Link ID Check Step 1
Interface Groups Provisioning
To initiate a request to the switch to reconcile E1 link IDs between the switch and the CPX-1000: Click the desired on the Tree View, the right-hand panel changes to the variant tabular view (Figure 6–27).
Figure 6–27. Variant Tabular View Step 2
Select the link number from the tabular view to which you want to check the link.
Step 3
Right-click the selected link number and select E1 Link ID Check from the popup menu.
Changing E1 Link States
The administrative and operational states of E1 Links are the same as those of other managed objects in the CPX-1000 (e.g. Interface Groups, network protection groups, IADs, etc.). Table 6–2 shows which operation is allowed given a certain state as well as the resulting state. The transition from Shutting Down to Locked is event driven from the CPX-1000. Typically, a Forced Blocked E1 link moves to Locked immediately from Shutting Down, but that is customer dependent.
Note A V5.1 link does not have its own Admin and Operational states.
November 2003
6-27
Interface Groups Provisioning
1000-A2-GB21-10
Table 6–2. E1 Link States Current State
Unblock
Deferred Block
Block Not Deferred
Forced Block
Unlocked
Not allowed (NA)
Shutting down
Shutting down
Shutting down
Shutting down
Unlocked
NA
Shutting down
Shutting down
Locked
Unlocked
NA
NA
NA
To change the E1 link states: Step 1
Click the desired on the Tree View, the right-hand panel changes to the variant tabular view (Figure 6–28).
Figure 6–28. Variant Tabular View Step 2
Select the desired variant from the tabular view.
Step 3
Right-click and select Switch Variant from the popup menu. The E1 Link Configuration window appears (Figure 6–29).
Figure 6–29. E1 Link Configuration Window
6-28
November 2003
1000-A2-GB21-10
Step 4
Interface Groups Provisioning
Make your selection from the drop-down list. Block Deferred
This block disables all non-assigned bearer channels on this link and waits until all assigned bearer channels (active calls) on the link are released. The LE attempts to protect any logical C-channels. During this time, the link is in the Shutting Down state. Once the active calls are released and the protection is completed, the LE sends a block indication to the CPX-1000, at which point the link is then Locked. Block Not Deferred This block attempts to use the protection protocol (if needed) to protect any logical C-channels on the indicated link. All active calls on the link are dropped. Once the active calls are released and the protection is completed, the LE sends a block indication to the CPX-1000, at which point the link is then Locked. If protection of the logical C-channels associated with the link was not possible, the LE rejects the block request by sending the CPX-1000 an unblock indication and the link remains in the Shutting Down state. Block Forced This block offers no protection on logical C-channels and the link is Locked immediately. If force blocking is done on the primary or secondary link of the interface, the entire Interface Group might be placed into a non-operational state. Unblock Step 5
November 2003
Click OK.
6-29
Interface Groups Provisioning
Viewing E1 Link Status
1000-A2-GB21-10
The status of the E1 links can be viewed. To view the E1 link states:
Step 1
Expand the desired CPX-1000 from the Tree View.
Step 2
Click the desired icon on the Tree View, the right-hand panel changes to the variant tabular view (Figure 6–30).
Figure 6–30. Variant Tabular View Step 3
Right-click the selected link number and select E1 Link Status. View the E1 link status (Figure 6–31).
6-30
November 2003
1000-A2-GB21-10
Interface Groups Provisioning
Figure 6–31. E1 Link Status
November 2003
6-31
Interface Groups Provisioning
6-32
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
7
Protection Group Provisioning This chapter provides instructions to provision ATM Protection Groups. This chapter includes the following tasks: Assigning members to the network Protection Group
(page 7-2) Swapping Protection Group members (page 7-4) Removing member from the Protection Group (page 7-5)
The ATM redundancy uses duplicate links between the ATM network and ATM card (DS-3 or STM-1) whereby you can assign which ATM interfaces on the CPX-1000 are associated with a particular Protection Group. Table 7–1 describes the fields in the Protection Group. Table 7–1. Protection Group Summary
November 2003
Fields
Description
ID
Four network Protection Groups are assigned by CPX Management Entity (CME). You cannot add or delete protection groups.
Primary Member
The active port of the Protection Group is specified by slot_number/port_number and indicated by a green background.
Secondary Member
The standby port of the Protection Group is indicated by a blue background. “Unassigned” indicates that the Protection Group has no members.
7-1
Protection Group Provisioning
1000-A2-GB21-10
Note The gray background indicates that the states (active/ standby) of the card are unknown because the card corresponding to a member has been removed; however, the slot/port information continues to display.
Assigning Protection Group Members Step 1
Before assigning members to the Protection Group, make sure that the CPX-1000 is up with redundant DS-3 or STM-1 cards. To assign members to the network Protection Group:
Click Network PG on the Tree View, the right-hand pane changes to the network Protection Group tabular view (Figure 7–1).
Figure 7–1. Network Protection Group Tabular View Step 2
Select a protection group to which you want to assign member.
Step 3
Select Configure from the Configuration menu. – Or – Right-click the highlighted selection and select Configure from the popup menu. The Configuration for Network PG window appears (Figure 7–2).
7-2
November 2003
1000-A2-GB21-10
Protection Group Provisioning
Figure 7–2. Configuration for Network PG Window Step 4
Select a slot and port number for the Primary Member from the Slot/Port drop-down list. Once a port assignment is selected, all other fields in the area are automatically populated.
Note Ensure that you assign the same port type to the same Protection Group.
Step 5
Select Unlocked from the Admin State drop-down list.
Step 6
Repeat Step 5 for the Secondary Member.
Step 7
Select a cable type: Y-cable or Straight.
Step 8
Click OK to return to the Main screen.
Step 9
Click Refresh CPX from the File Menu. The newly created Protection Groups display in the tabular view (Figure 7–3).
Figure 7–3. Protection Groups Displayed in Tabular View
November 2003
7-3
Protection Group Provisioning
Swapping Protection Group Members Step 1
1000-A2-GB21-10
To switch between the Primary and Secondary Protection Group members:
Click Network PG on the Tree View, the right-hand pane changes to the network Protection Group tabular view (Figure 7–4).
Figure 7–4. Protection Groups Displayed in Tabular View Step 2
Select a Protection Group ID to which you want to switch member.
Step 3
Select PG Swap from the Configuration menu. – Or – Right-click the highlighted selection and select PG Swap from the popup menu.
7-4
Step 4
Click OK to return to the Main screen.
Step 5
Select Refresh CPX from the File menu. The Primary Member is now blue and the Secondary Member green.
November 2003
1000-A2-GB21-10
Removing Protection Group Members Step 1
Protection Group Provisioning
Before removing members from a Protection Group, ensure that the port assigned to the group member is Locked. To remove members from a Protection Group:
Click Network PG on the Tree View, the Protection Group Manager window similar to Figure 7–5 appears.
Figure 7–5. Protection Groups Displayed in Tabular View Step 2
Select a Protection Group member that you want to remove.
Step 3
Select Configure from the Configuration menu. – Or – Right-click the highlighted selection and select Configure from the popup menu. The Configuration for Network PG window similar to Figure 7–6 appears.
Figure 7–6. Configuration for Network PG Window
November 2003
7-5
Protection Group Provisioning
1000-A2-GB21-10
Step 4
Select Unassigned from the Slot/Port drop-down list for the Secondary Member.
Step 5
Select Locked from the Admin State drop-down list.
Step 6
Repeat Step 5 for the Primary Member.
Note The unassigned list does not appear in the Slot/ Port drop-down list in the Primary Member area until after you select unassigned for the Secondary Member. This selection ensures that the primary port (Primary Member) remains assigned when the secondary port is unassigned.
7-6
Step 7
Click OK to return to the Main screen.
Step 8
Select Refresh CPX from the File menu to view your changes.
November 2003
C
H
A
P
T
E
R
8
IAD Profiles and ISDN Port Templates Provisioning This chapter provides instructions to provision IAD Profiles and ISDN port templates. This chapter includes these topics: Provisioning IAD Profiles
— Creating IAD Profiles (page 8-2) — Modifying IAD Profiles (page 8-3) — Deleting IAD Profiles (page 8-5) Provisioning ISDN Port Templates
— Creating ISDN Port Template (page 8-7) — Modifying ISDN Port Template (page 8-9) — Deleting ISDN Port Template (page 8-11) The IAD Profile establishes a set of allowable parameters that can be used when setting up different types of IADs. Once an IAD Profile is created, you can customize the profile parameters for each IAD port. You can create as many IAD profiles as you want or use one of the default IAD profiles provided by JetCraft: Jetstream IAD-Flex Jetstream IAD-801 Jetstream IAD-802
The ISDN port template specifies a Dchannel configuration that can be set against any given port on an ISDN IAD. This data must match the LE provisioning exactly for the port to function.
Note Defining the ISDN port template is optional. If you intend to provision a large number of ISDN IAD, then a predefined ISDN port template will simplify the data entry aspects of provisioning ISDN IADs.
November 2003
8-1
IAD Profiles and ISDN Port Templates Provisioning
Adding IAD Profiles Step 1
1000-A2-GB21-10
To add an IAD Profile:
Click on the Tree View and select Create IAD Profile from the Configuration menu. – Or – Right-click on the Tree View and select Create IAD Profile from the popup menu. The Add IAD Profile window appears (Figure 8–1).
Figure 8–1. Add IAD Profile Window Step 2
8-2
Type the name of the profile that you are creating (up to 16 alphanumeric characters, including spaces and hyphens) in the Profile Name field.
November 2003
1000-A2-GB21-10
IAD Profiles and ISDN Port Templates Provisioning
Note You can select a combination of options available. For example, If your profile uses Loop, Ground, and ISDN, select them all. Your selections appear in the Default Value field.
Step 3
Click to select the number of ports available for the profile.
Step 4
Click to select the data transport type.
Step 5
Click to select the compression type.
Step 6
Click to select the echo cancellation.
Step 7
Click to select the signalling type.
Step 8
Click OK to save your IAD Profile.
Modifying IAD Profiles
To modify an IAD Profile:
Note IAD Profiles associated with an IAD cannot be modified unless all IADs that use that IAD Profile have been deleted.
Step 1
Click on the Tree View and select IAD Profile Manager from the Configuration menu. – Or – Click
on the toolbar.
The update IAD Profile window appears (Figure 8–2). From this window, you can also: add a profile (page 8-2) delete a profile (page 8-5)
November 2003
8-3
IAD Profiles and ISDN Port Templates Provisioning
1000-A2-GB21-10
Figure 8–2. Update IAD Profile Window Step 2
Select the profile you want to modify, then click Modify. The Modify IAD Profile window appears (Figure 8–3).
Figure 8–3. Modify IAD Profile Window
8-4
November 2003
1000-A2-GB21-10
IAD Profiles and ISDN Port Templates Provisioning
Step 3
Modify any fields, if necessary (Adding IAD Profiles on page 8-2).
Step 4
Click OK to modify the IAD Profile.
Deleting IAD Profiles
To delete an IAD Profile:
Note IAD Profiles associated with an IAD cannot be deleted, unless all IADs that use the to be deleted IAD Profile have been deleted.
Step 1
Click on the Tree View and select IAD Profile Manager from the Configuration menu. – Or – Click
on the toolbar.
The Update IAD Profile window appears (Figure 8–3).
Figure 8–4. Update IAD Profile Window
November 2003
Step 2
Click the name of the IAD Profile that you want to delete.
Step 3
Click Delete. A prompt appears, asking if you want to delete the profile.
Step 4
Click Yes to delete the profile.
8-5
IAD Profiles and ISDN Port Templates Provisioning
ISDN Port Templates Summary
1000-A2-GB21-10
Table 8–1 lists and describes the configurable parameters when creating the ISDN port template.
Table 8–1. ISDN Configurable Parameters Summary Parameter
Description
Template Name
The name of the template to be created.
Template Description
An optional field that describes the template.
Channel Type
Options are Physical and Logical. Physical link is the actual connection to the E1 card. Logical link is a connection between two logical nodes
(e.g., virtual path connection). Logical Channel ID
Use only when the channel type is logical. Its value is between 0 to 65503.
Link Number
For V5.1, the physical link number is 1. For V5.2, the physical link number is between 1 to 16
Time Slot
8-6
The time slot assignment is 15, 16, and 31.
November 2003
1000-A2-GB21-10
Creating ISDN Port Template Step 1
IAD Profiles and ISDN Port Templates Provisioning
To create an ISDN port Template:
Click on the Tree View and select Create ISDN Port Template from the Configuration menu. The ISDN Port Template Creation window appears (Figure 8–5).
Figure 8–5. ISDN Port Template Creation Window Step 2
Type the name of the template to be created in the Template Name field.
Step 3
Optionally, describe the template (e.g., V5.1) in the Template Description field.
Note Data received from an ISDN Dch connection can be routed to and/or from different DS0s on the given V5.2 interface based upon signaling type (P-type, F-type, or D-type). Make sure to enter information for each signaling type in the appropriate fields.
November 2003
8-7
IAD Profiles and ISDN Port Templates Provisioning
Step 4
1000-A2-GB21-10
Set the channel type for each signaling type by selecting from the associated drop-down list. For V5.1, select Physical For V5.2, select Physical or Logical
Step 5
Type the logical ID (if Logical is selected from Step 4) between 0 – 65503 in the Logical Channel ID field.
Step 6
Select the physical link number from the Link Number drop-down list. For V5.1, select 1 For V5.2, select between 1–16
Note The link number specified here is used when the V5 interface is provisioned. This number is usually not the same as the V5.2 E1 Link ID.
8-8
Step 7
Select the E1 time slot assignment from the Time Slot drop-down list. Options are 15, 16, and 31.
Step 8
Click OK to return to the Main screen.
November 2003
1000-A2-GB21-10
IAD Profiles and ISDN Port Templates Provisioning
Modifying ISDN Port Template Note Modifying a template does not affect the ISDN ports that are using the associated template. Instead of linking the parameters as in the IAD Profiles, the parameters of the template are embedded (i.e., become part of) into the ISDN ports.
To modify an ISDN port Template: Step 1
Click on the Tree View and select ISDN Port Template Manager from the Configuration menu. – Or – Click
on the toolbar.
The ISDN Port Template Manager window appears (Figure 8–6). From this window, you can also: add a template (page 8-7) delete a template (page 8-11)
Figure 8–6. ISDN Port Template Manager Window
November 2003
8-9
IAD Profiles and ISDN Port Templates Provisioning
Step 2
1000-A2-GB21-10
Select the name of the template that you want to modify, then click Modify. The ISDN Port Template Modification window appears (Figure 8–7)
Figure 8–7. ISDN Port Template Modification Window Step 3
Modify any fields, if necessary (Creating ISDN Port Template on page 8-7).
Note The name of the template cannot be modified. Step 4
8-10
Click OK to return to the Main screen.
November 2003
1000-A2-GB21-10
IAD Profiles and ISDN Port Templates Provisioning
Deleting ISDN Port Template Note Deleting a template does not affect the ISDN ports that are using the associated template. Instead of linking the parameters as in the IAD Profiles, the parameters of the template are embedded (i.e., become part of) into the ISDN ports. To delete an ISDN port Template: Step 1
Click on the Tree View and select ISDN Port Template Manager from the Configuration menu. – Or – Click
on the toolbar.
The ISDN Port Template Manager window appears (Figure 8–8).
Figure 8–8. ISDN Port Template Manager Window
November 2003
Step 2
Select the name of the template that you want to delete, then click Delete. A message appears, asking if you want to delete the selected template.
Step 3
Click Yes, and the template is deleted.
Step 4
Click Close to return to the Main screen.
8-11
IAD Profiles and ISDN Port Templates Provisioning
8-12
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
9
IADs Provisioning
This chapter provides instructions to provision IADs, including Creating IADs with V5.2 IG (page 9-4) Creating IADs with V5.1 IG (page 9-11) Modifying IADs (page 9-18) Deleting IADs (page 9-21) Filtering IADs (page 9-23)
IADs
IADs are installed at the customer/subscriber premises. Figure 9–1 shows the relationship of an IAD to a Voice-over-Broadband (VoBB) network. Directory Number per Port - ID - Serial No. - Interface Group - State
Phone Sys
CPX1000
I AD LAN
ATM Transport
DSLAM
ATM Switch
Phone Sys I AD LAN
- DSLAM Name - ILEC Company
Permanent Virtual Circuit (PVC) per IAD - ATM/port - VPI 0059 - VCI
Figure 9–1. IAD Installation Before the IADs are physically installed, you create and configure them in the CPX-1000 (you can install an IAD first, but it won’t go into service until the IAD is created and configured in the CPX-1000). The CPX-1000 supports up to 2,000 IADs.
November 2003
9-1
IADs Provisioning
1000-A2-GB21-10
Before you can create and provision an IAD, ensure that you have created Interface Groups, Protection Groups, and IAD Profiles. When an IAD is first created, the administrative state for all ports are set to Unlocked and the operational state is Disabled. When the IAD becomes operable, the operational state changes to Enabled. After you have created Interface Groups and IAD Profiles, you can then use the Create IAD window to create and provision an IAD.
Note Defining the ISDN port template is optional. If you intend to provision a large number of ISDN IADs, then a predefined ISDN port template will simplify the data entry aspects of provisioning ISDN IADs.
For downloading IAD software instructions, refer to Chapter 12, CPX-1000 Maintenance and Services. For IADs reports and statistics information, refer to Chapter 11, Alarms, Events, and Statistics.
IAD Admin States
When an IAD is first created, the administrative state is Provisional and the operational state is Disabled. When the IAD becomes operable, the administrative state automatically changes to Unlocked and the operational state changes to Enabled. The IAD administrative state determines which IAD and IAD port options can be modified. Four administrative states are available: Provisional Unlocked Locked Shutting Down
Most modifiable options are determined by the IAD administrative state; however, the CRV and signaling are determined by the administrative states of the IAD and its port. For example, if the administrative state of the IAD is Unlocked and the port administrative state is Locked, both CRV and signaling can be modified.
9-2
November 2003
1000-A2-GB21-10
IADs Provisioning
If the administrative state for IAD and its ports are both Unlocked, then neither the CRV or the signaling can be modified (Table 9–1).
Table 9–1. Modifiable Options in Different Administrative States At IAD Level…
At Port Level…
Tasks/ Admin State
Profile Name
Service Affecting
# of Ports
IAD Port Admin State
Create IAD/ Provisional
Yes
Yes
Yes
Modify IAD/ Provisional
No
No
Yes
Modify IAD/ Unlocked
No
Modify IAD/ Locked
No
Create/ Modify IAD w/RT Provisioned
Yes
November 2003
No
Yes
No
Yes
CRV
Signaling
Echo
Compression
Locked or Unlocked
Yes
Yes
Yes
Yes
Locked
Yes
Yes
Yes
Yes
Unlocked
No
No
Locked
Yes
Yes
Unlocked
No
No
Locked or
Yes
Yes
Yes
Yes
Yes
No
No
No
No Yes
Yes No
Unlocked Yes
Yes
Locked or Unlocked
9-3
IADs Provisioning
1000-A2-GB21-10
Creating IADs withV5.2 IG Step 1
To create an IAD with V5.2 Interface Group:
Select Create IAD from the Configuration menu. – Or – Right-click on the Tree View or Map View and select Create IAD from the popup menu. – Or – Click
on the toolbar.
The IAD Creation Wizard–Introduction screen appears (Figure 9–2).
Figure 9–2. IAD Creation Wizard–Introduction Screen
9-4
November 2003
1000-A2-GB21-10
Step 2
IADs Provisioning
Click Next. The Informational screen appears (Figure 9–3).
Figure 9–3. IAD Creation Wizard–Informational Screen Step 3
Click Next. The IAD Creation Wizard–IAD Profile Selection screen appears (Figure 9–4).
Figure 9–4. IAD Creation Wizard–IAD Selection Screen
Note The Next button is enabled when the profile information is selected.
November 2003
9-5
IADs Provisioning
1000-A2-GB21-10
Step 4
Select an IAD Profile (e.g, POTS or ISDN) from the IAD Profile drop-down list. The IAD Type field is automatically populated.
Step 5
Click Next. The IAD Creation Wizard–Interface Group Selection screen appears (Figure 9–5).
Figure 9–5. IAD Creation Wizard–IG Selection Screen Step 6
Select a Interface Group from the Interface Group ID drop-down list. The Interface Group version field (e.g., V5.2) is automatically populated.
Step 7
Click Next. The IAD Creation Wizard–ATM Protection Group Configuration screen appears (Figure 9–6).
Figure 9–6. IAD Creation Wizard–ATM PG Configuration Screen
9-6
November 2003
1000-A2-GB21-10
IADs Provisioning
Step 8
Select the Protection Group that the IAD is assigned from the ATM Protection Group drop-down list.
Step 9
Type the VPI value between 0 to 255 in the VPI field.
Note Changing the VPI value is available only to Release 3.1 or later. If you have an earlier release, the only valid entry for VPI is 0.
Step 10
Type the VCI value in the VCI field. This identifies the subscriber-specific virtual circuit between the CPX-1000 and the ATM network. If VPI is 0, then the VCI range is 32 to 1023. If VPI is >0, then the VCI range is 0 to 1023. (Refer to
Chapter 5, CPX-1000 Configuration, for VCI setting.) Step 11
Select either ATM or Frame Relay from the Transport drop-down list. Transport selections are dependant upon the IAD Profile.
Step 12
Click Next. The Reference Configuration screen appears (Figure 9–7).
Figure 9–7. IAD Creation Wizard–Reference Configuration Screen
November 2003
9-7
IADs Provisioning
1000-A2-GB21-10
Step 13
Type the optional information in their associated fields. Company—the company providing the voice service DSLAM—the DSLAM serving the subscribers Subscriber—the name of the subscriber
Step 14
Click Next. The IAD Creation Wizard–Port Configuration screen appears (Figure 9–8).
Figure 9–8. IAD Creation Wizard–Port Configuration Screen
Note The number of ports is dependant upon the IAD Profile. The field is automatically populated based on the profile selection.
Step 15
Type the starting address (if necessary) in the Starting Address field.
Note All Layer 3 addresses must be unique across IADs within the same Interface Group.
9-8
November 2003
1000-A2-GB21-10
Step 16
IADs Provisioning
Click to select the values for the following IAD port parameters from the associated drop-down list. Provisioning Admin State Signaling Echo Cancellation
Step 17
Click Next. For creating POTS IADs, go to Step 22 on page 9-10. The
IAD Creation Summary screen appears, listing the IAD parameters you’ve just created. For creating ISDN IADs, the IAD Creation Wizard–D
Channel Assignment screen appears (Figure 9–9). Then continue with the next step.
Figure 9–9. IAD Creation Wizard–D Channel Assignment Screen Step 18
Assign the D channel data entry for each port. If a template is defined, select one from the Available
ISDN Port Template drop-down list. If a template is unavailable, select the values from the
appropriate drop-down lists.
November 2003
9-9
IADs Provisioning
1000-A2-GB21-10
Step 19
Select the channel type for each signaling type (P-type, F-type, and D-type) by selecting from the Channel Type drop-down list.
Step 20
Set the timelsot for each signaling type (P-type, F-type, and D-type) by selecting from the Timeslot drop-down list.
Step 21
Click Next. The IAD Creation Summary screen appears, listing the IAD parameters you’ve just created (Figure 9–10).
Figure 9–10. IAD Creation Wizard–D Channel Assignment Screen Step 22
Review the IAD parameters. If parameters are correct, click Create IAD. If any of parameters are incorrect, click Back until you reach
the screen in question and correct the parameters, then proceed from that point forward.
9-10
November 2003
1000-A2-GB21-10
Creating IADs with V5.1 IG Step 1
IADs Provisioning
To create an IAD with V5.1 Interface Group: Select Create IAD from the Configuration menu. – Or – Right-click on the Tree View or Map View and select Create IAD from the popup menu. – Or – Click
on the toolbar.
The IAD Creation Wizard–Introduction screen appears (Figure 9–11).
Figure 9–11. IAD Creation Wizard–Introduction Screen
November 2003
9-11
IADs Provisioning
1000-A2-GB21-10
Step 2
Click Next. The Informational screen appears (Figure 9–3).
Figure 9–12. IAD Creation Wizard–Informational Screen Step 3
Click Next. The IAD Creation Wizard–IAD Profile Selection Window appears (Figure 9–4).
Figure 9–13. IAD Creation Wizard–IAD Profile Selection Window
Note The Next button is enabled when the profile information is selected.
9-12
November 2003
1000-A2-GB21-10
IADs Provisioning
Step 4
Select an IAD Profile (e.g, POTS or ISDN) from the IAD Profile drop-down list. The IAD Type field is automatically populated.
Step 5
Click Next. The IAD Creation Wizard–Interface Group Selection Window appears (Figure 9–14).
Figure 9–14. IAD Creation Wizard–IG Selection Window Step 6
Select a Interface Group from the Interface Group Name drop-down list. The Interface Group version field (e.g., V5.1) is automatically populated.
Step 7
Click Next. The IAD Creation Wizard–ATM Protection Group Configuration Window appears (Figure 9–15).
Figure 9–15. IAD Creation Wizard–ATM Protection Group Configuration Window
November 2003
9-13
IADs Provisioning
1000-A2-GB21-10
Step 8
Select the Protection Group that the IAD is assigned from the ATM Protection Group drop-down list.
Step 9
Type the VPI value between 0 to 255 in the VPI field.
Note Changing the VPI value is available only to Release 3.1 or later. If you have an earlier release, the only valid entry for VPI is 0. Step 10
Type the VCI value in the VCI field. This identifies the subscriber-specific virtual circuit between the CPX-1000 and the ATM network. If VPI is 0, then the VCI range is 32 to 1023. If VPI is >0, then the VCI range is 0 to 1023. (Refer to
Chapter 5, CPX-1000 Configuration, for VCI setting.) Step 11
Type the VCI value in the VCI field. This identifies the subscriber-specific virtual circuit between the CPX-1000 and the ATM network.
Step 12
Select either ATM or Frame Relay from the Transport drop-down list. Transport selections are dependant upon the IAD Profile.
Step 13
Click Next. The Reference Configuration screen appears (Figure 9–16).
Figure 9–16. IAD Creation Wizard–Reference Configuration Screen
9-14
November 2003
1000-A2-GB21-10
Step 14
IADs Provisioning
Type the optional information in their associated fields. Company—the company providing the voice service DSLAM—the DSLAM serving the subscribers Subscriber—the name of the subscriber
Step 15
Click Next. The IAD Creation Wizard–Port Configuration screen appears (Figure 9–17).
Figure 9–17. IAD Creation Wizard–Port Configuration Window
Note The number of ports is dependant upon the IAD Profile. The field is automatically populated based on the profile selection.
Step 16
Type the starting address in the Starting Address field.
Note All Layer 3 addresses must be unique across IADs within the same Interface Group.
November 2003
9-15
IADs Provisioning
1000-A2-GB21-10
Step 17
Click to select the values for the following IAD port parameters from the associated drop-down list. Provisioning Admin State Signaling Echo Cancellation
Step 18
Click Next. The IAD Creation Wizard–B Channel Assignment window appears (Figure 9–18).
B Channel assignment for ISDN configuration
B Channel assignment for POTS configuration
Figure 9–18. IAD Creation Wizard–B Channel Assignment Screen
Note The valid timeslots for both the B1 and Bearer timeslots are 1 through 15 and 17 through 31.
9-16
November 2003
1000-A2-GB21-10
IADs Provisioning
Step 19
Set the bearer channel timeslots for each port by selecting from the associated drop-down lists.
Step 20
Click Next. For creating POTS IADs, go to Step 24 on page 9-18. The
IAD Creation Summary screen appears, listing the IAD parameters you’ve just created. For creating ISDN IADs, the IAD Creation Wizard–D
Channel Assignment screen appears (Figure 9–19). Then continue with the next step.
Figure 9–19. IAD Creation Wizard–D Channel Assignment Screen Step 21
Assign the D channel data entry for each port. If a template is defined, select one from the Available
ISDN Port Template drop-down list. If a template is unavailable, select the values from the
appropriate drop-down lists.
Note With V5.1 configuration, the channel type is always physical and the link number is 1.
Step 22
November 2003
Set the timelsot for each signaling type (P-type, F-type, and D-type) by selecting from the Timeslot drop-down list.
9-17
IADs Provisioning
1000-A2-GB21-10
Step 23
Click Next. The IAD Creation Summary screen appears, listing the IAD parameters you’ve just created (Figure 9–20).
Figure 9–20. IAD Creation Wizard–IAD Creation Summary Screen Step 24
Review the IAD parameters. If parameters are correct, click Create IAD. If any of parameters are incorrect, click Back until you reach
the screen in question and correct the parameters, then proceed from that point forward.
Modifying IADs Step 1
To modify IAD information:
Select IAD Manager from the Configuration menu. – Or – Right-click on the Tree View or Map View and select IAD Manager from the popup menu. – Or – Click
at the toolbar.
The IAD Configuration Manager window appears (Figure 9–21).
9-18
November 2003
1000-A2-GB21-10
IADs Provisioning
Click here to display IADs
Figure 9–21. IAD Configuration Manager Window Step 2
Click Show IADs. The configured IADs appear, and a message in the status bar indicates how many IADs are retrieved (Figure 9–22).
Number of IADs retrieved
Figure 9–22. IAD Configuration Manager Window with IADs Displayed
November 2003
9-19
IADs Provisioning
1000-A2-GB21-10
Step 3
Select the IAD you want to modify, click Lock to place the IAD out of service.
Note If the changes are not service affecting (i.e., changes in the Reference tab), you do not need to lock the IAD.
Step 4
Click Modify. The IAD Modification window appears (Figure 9–23).
Figure 9–23. IAD Modification Window
Note If you omit Step 3, click the State tab and lock the IAD.
9-20
November 2003
1000-A2-GB21-10
IADs Provisioning
Step 5
Modify information in the desired tabs, as necessary.
Step 6
Click OK to accept the changes and return to the IAD Configuration Manager window.
Step 7
Click Close to return to the Main screen.
Step 8
Select Refresh CPX from the File menu to update the changes.
Deleting IADs Step 1
To delete an IAD: Select IAD Manager from the Configuration menu. – Or – Right-click Manager.
on the Tree View or Map View and select IAD
– Or – Click
at the toolbar.
The IAD Configuration Manager window appears (Figure 9–24). Click here to display IADs
Figure 9–24. IAD Configuration Manager Window
November 2003
9-21
IADs Provisioning
1000-A2-GB21-10
Step 2
Click Show IADs. The configured IADs appear, and a message in the status bar indicates how many IADs are retrieved (Figure 9–25).
Number of IADs retrieved
Figure 9–25. IAD Configuration Manager Window with IADs Displayed Step 3
Select the IAD you want to delete, click Lock to place the IAD out of service.
Note To select multiple IADs, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select IADs in a random order.
Step 4
Click Delete. The Delete IAD window appears (Figure 9–26).
Figure 9–26. Delete IAD Window
9-22
November 2003
1000-A2-GB21-10
Step 5
IADs Provisioning
Click one of the following: Yes: deletes a single IAD and returns you to the IAD
Configuration Manager window. Yes To All: deletes all selected IADs. No: returns you to the IAD Configuration Manager window. No To All: returns you to the IAD Configuration Manager
window. Step 6
Click Close to return to the Main screen.
Step 7
Select Refresh CPX from the File menu to update the changes.
Reviewing IADs
To review IAD information, select IAD Manager from the Configuration menu, or right-click on the Tree View or Map View, or click on the toolbar.
Searching IADs by Fields
You can customize the search of IADs by using one or both of the following fields: Company and DSLAM and Subscriber Network Protection Groups, Interface Group, IAD
hardware model, and Directory Step 1
Select IAD Manager from the Configuration menu. – Or – Right-click Manager.
on the Tree View or Map View and select IAD
– Or – Click
at the toolbar.
The IAD Configuration Manager window appears (Figure 9–27).
November 2003
9-23
IADs Provisioning
1000-A2-GB21-10
Click one or both checkboxes to filter IADs
Figure 9–27. View/Update IAD Window Step 2
Specify your search by clicking one or a combination of the following areas: Company and DSLAM and Subscriber Network Protection Groups, Interface Group, hardware
(HW) model, and Directory Searching by Company, DSLAM, and Subscriber Step 1
Proceed as Steps 1 and 2 in Searching IADs by Fields on page 9-23.
Step 2
Click the checkbox next to Company, and select the name of the company assigned to the IADs from the drop-down list. The DSLAM and the subscriber for that company is automatically selected. Searching by the Network Protective Groups
9-24
Step 1
Proceed as Steps 1 and 2 in Searching IADs by Fields on page 9-23.
Step 2
Select Network Protection Group from the drop-down list. Both the VCI and VPI fields are enabled.
Step 3
Type the Network Protection Group identifier, or select it from the drop-down list.
November 2003
1000-A2-GB21-10
IADs Provisioning
Step 4
Select a range of VCI values by using the less than (<) or greater than (>) symbols from the drop-down list, then type a VCI value in the text field.
Step 5
Select a range of VPI values by using the less than (<) or greater than (>) symbols from the drop-down list, then type a VPI value in the text field.
Note When the L3/VCI/VPI value is not specified, All (default) is used. The default indicates that the filter only applies to the Interface Group or Network Protection Group, regardless of the L3/VCI/VPI value. Searching by the Interface Groups Step 1
Proceed as Steps 1 and 2 in Searching IADs by Fields on page 9-23.
Step 2
Select Interface Group from the drop-down list.
Step 3
Type the Interface Group identifier, or select it from the drop-down list.
Step 4
Select a range of L3 by using the less than (<) or greater than (>) symbols from the drop-down list.
Step 5
Type a L3 number, or select it from the drop-down list. Searching by the Hardware Model and Software Version
Step 1
Proceed as Steps 1 and 2 in Searching IADs by Fields on page 9-23.
Step 2
Select HW Model from the drop-down list.
Step 3
Type the model type, or select it from the drop-down list.
Step 4
To further refine the search, select a software version from the SW Version drop-down list, or leave the default as ALL to select all software versions.. The software version(s) available in the list depends upon the hardware model chosen.
November 2003
9-25
IADs Provisioning
1000-A2-GB21-10
Searching by Directory
9-26
Step 1
Proceed as Steps 1 and 2 in Searching IADs by Fields on page 9-23.
Step 2
Select Directory from the drop-down list.
Step 3
Type the directory information that you would like to find.
November 2003
C
H
A
P
T
E
R
10
Network Resource Manager
Overview
The Network Resource Manager (NRM) is a mechanism to allow carriers to manage constraints within their network. These constraints may be bandwidth or number of calls a network resource can handle without service degradation. In typical VoBB deployments, the first method of defense against bandwidth over-allocation is prioritization: voice traffic is granted priority over data traffic, so as more calls are allowed to enter the network, data traffic is reduced. However, it is critical that Call Admission Control be properly performed. If a packet link is overloaded with high priority traffic, the network cannot identify which packets to throw away, so all calls are affected (not just those recently added). The results can be catastrophic, with dozens of calls rendered unintelligible. While the CPX-1000 does not have direct knowledge of the network, it can track resources that are common to IADS. The CPX can learn the topology of the network and the associated network constraints and perform the Call Admission Control (CAC). The CPX can support up to 256 network resources with a provisionable bandwidth thresholds. The CPX can then track utilization of each network resource. Before starting a call, it verifies that there is sufficient bandwidth available for the associated network resource to accept the call. If not, the call is rejected. This chapter describes: Provisioning network resources Configuring network resources for IADs
November 2003
10-1
10. Network Resource Manager
Provisioning
1000-A2-GB21-10
The user can create, modify and delete network resources from the NRM window. These operations can be performed using the tool bar or the Operations menu in the Network Resource Manager window. To provision network resources:
Step 1
Click a desired CPX-1000 icon in the Tree view.
Step 2
Select Network Resource Manager from the Services menu. The Network Resource Manager window appears (Figure 10–1).
Figure 10–1. Network Resource Management Window Step 3
Select Create from the Operations menu - Or Click the Create icon appears.
10-2
on the toolbar. A Create dialog box
November 2003
1000-A2-GB21-10
10. Network Resource Manager
Figure 10–2. Network Resource Manager Create Dialog Step 4
Enter the following information: Network Resource Name. Enter from 4 to 63 alphanumeric
characters (including no spaces, hyphens, or special characters). Maximum Bandwidth (Cells/sec). Enter a number between
200 and 1466981, inclusive. Step 5
Modifying a Network Resource
Click on OK. The new network resource you created appears in the Network Resource Manager Window. To modify a provisioned network resource:
Step 1
Select a network resource in the Network Resource Manager window.
Step 2
Select Modify from the Operations menu – Or – Click
Step 3
Make your desired modifications.
Step 4
Click on OK.
Deleting a Network Resource
November 2003
on the toolbar. The Modify dialog window appears.
To delete a provisioned network resource:
10-3
10. Network Resource Manager
1000-A2-GB21-10
Step 1
Select a network resource in the Network Resource Manager window.
Step 2
Click the Delete icon. A deletion confirmation window appears. Click on OK. Click on Close to exit the Network Resource Manager.
10-4
November 2003
C
H
A
P
T
E
R
11
Alarms, Events, and Statistics This chapter describes JetCraft alarms and error and performance statistics. It also provides instructions for setting the alarm polling interval and statistics collection. This chapter includes: Alarms notification (page 11-1) CPX alarms (page 11-3) Setting alarm polling interval (page 11-3) Accessing network Protection Groups statistics (page 11-9) Accessing IADs statistics (page 11-10) Accessing E1 links (page 11-11) Graphing statistics (page 11-12)
Alarms Notification
When a fault occurs that generates an alarm for a CPX-1000 network element, JetCraft provides immediate alarm notification in two places: An alarm message appears in the Alarm window
(Figure 11–1). An alarm mark (colored “X”) identifies the alarmed element
in the Tree and Shelf views. Figure 11–2 shows an alarm in the Tree View. The color of the alarm is the most immediate indication of its importance (Table 11–1).
Figure 11–1. Alarm Window
November 2003
11-1
Alarms, Events, and Statistics
1000-A2-GB21-10
Colored X indicating alarms
Figure 11–2. Alarmed Element in the Tree View Table 11–1. Alarm Severity by Color
11-2
Alarm Severity
Color
Critical
red
Major
orange
Minor
yellow
November 2003
1000-A2-GB21-10
CPX Alarms
Alarms, Events, and Statistics
JetCraft displays current alarms in the Alarm window (Figure 9–1 on page 9-1). The Alarm window is located above the status bar at the bottom of the JetCraft Main window. From the Alarm window, you can sort alarms alphabetically by selecting a column (Severity, Time, Equipment, and Description). To sort by another type of alarm information, select another column. The CPX-1000 maintains a lists of up to 1,000 active alarms. To view the current alarm summary, select a CPX-1000 component and click on the toolbar.
Setting Alarm Polling Interval Step 1
To set an alarm polling interval:
Select Alarm Polling Interval Configuration from the Services menu. The Alarm Polling Interval Configuration window appears (Figure 11–3).
Figure 11–3. Alarm Polling Interval Configuration Step 2
Type a time interval in the Alarm Polling Interval field.
Note We recommend setting the polling interval to a minimum of 15 seconds.
Step 3
November 2003
Click OK.
11-3
Alarms, Events, and Statistics
Statistics
1000-A2-GB21-10
With JetCraft, you can graph various levels of error or performance statistics based on the element you have selected. Only online graphing (no printing) is available for current data. Online graphs are charted over a user-defined interval, up to fifteen minutes. Error graphs display absolute and relative values. Clicking Show marks the initial absolute value. Clicking Reset freezes the absolute value, and starts marking new relative values. Subsequent resets add the last relative value to the absolute value, and start marking new relative values (Figure 11–4). These values are in minutes. There are different methods to poll various levels of error or performance statistics based on the element you select. For statistics on CPX-1000, STM-1 ports, and MP card, go to Graphing Statistics on page 11-12. For other elements, refer to the following: Network Protection Group (page 11-9) IADs (page 11-10)
11-4
November 2003
1000-A2-GB21-10
Alarms, Events, and Statistics
Click Show to mark the initial absolute value
Click Reset to display the relative value
Absolute
Relative
Figure 11–4. Absolute and Relative Values
November 2003
11-5
Alarms, Events, and Statistics
Statistics Summary
1000-A2-GB21-10
Table 11–2 lists error and performance statistics that you can graph for various CPX-1000 managed entities. The statistics you can graph depends on the currently selected network element. For example, if you select a port, then you can graph port statistics. Refer to Appendix B, Statistics Definitions, for definitions of errors and performance statistics.
Table 11–2. Summary of Error and Performance Statistics Selected Element
Error Statistics Available
Performance Statistics Available
CPX-1000
Assembly errors
Active calls
Blocked incalls
Ctrl cells rcvd
Blocked outcalls
Ctrl cells sent
CRC errors
Cumulative calls
IADs down
IADs Provisioned IADs Up Peak calls
MP card
Not applicable
Available physical memory (MB) CPU usage (percent) Disk size (MB) Disk usage (MB) Disk usage (percent) Free disk space (MB) Free page size (MB) Page size (MB) Page usage (MB) Page usage (percent) Physical memory (MB) Physical memory usage (MB) Physical memory usage (percent)
Protection Group
Not applicable
Automatic switches Manual switches Switches to primary Switches to secondary
11-6
November 2003
1000-A2-GB21-10
Alarms, Events, and Statistics
Table 11–2. Summary of Error and Performance Statistics (Continued) Selected Element
Error Statistics Available
Performance Statistics Available
ATM DS-3
Loss os signal
Not applicable
Loss os frame Far end receive failure Red count Out of cell delineation Loss of cell delineation Far end alarm indication STM-1 port
AAL1 byte CRC errors
Cell is rcvd
AAL1 byte parity errors
Cell is sent
AAL1 byte seq errors
Open RX VCs
Clock generation failures
Open TX VCs
Ref cell loss Ref cell out of sync TDM master clocks absent IAD
Assembly errors
Active calls
Blocked incalls
Cells rcvd
Blocked outcalls
Cells sent
CRC errors
Ctrl cells rcvd Ctrl cells sent Cumulative calls Peak calls
November 2003
11-7
Alarms, Events, and Statistics
1000-A2-GB21-10
Table 11–2. Summary of Error and Performance Statistics (Continued) Selected Element
Error Statistics Available
Performance Statistics Available
E1 links
Alarm Indication Signal Seconds— last 15 minutes
DS0s in use
Bipolar Violations—last 15 minutes Bursty Errored Seconds—last 15 minutes Controlled Slips Seconds—last 15 minutes Controlled Slips—last 15 minutes Degraded Minutes—last 15 minutes Errored Seconds—last 15 minutes Excessive Zeroes—last 15 minutes Line Coding Violations—last 15 minutes Line Errored Seconds—last 15 minutes Out Of Frame Seconds—last 15 minutes Path Coding Violations—last 15 minutes Severely Errored Framing Seconds—last 15 minutes Severely Errored Seconds—last 15 minutes Unavailable Seconds—last 15 minutes
11-8
November 2003
1000-A2-GB21-10
Accessing Network Protection Groups Step 1
Alarms, Events, and Statistics
To access the network Protection Group statistics:
Click Network PG on the Tree View to display the network protection group list. (Figure 11–5).
Figure 11–5. Network Protection Group Tabular View Step 2
Select a Protection Group member on which you want to poll statistics (only Performance statistics is available).
Step 3
Select Performance Graphs from the Report menu. – Or – Right-click the highlighted selection and make your selection.
Step 4
November 2003
Continue with Step 3 in Graphing Statistics on page 11-12.
11-9
Alarms, Events, and Statistics
Accessing IADs Step 1
1000-A2-GB21-10
To access the IADs statistics: Select IAD Manager from the Configuration menu. – Or – Right-click Manager.
on the Tree View or Map View and select IAD
– Or – Click
at the toolbar.
The IAD Configuration Manager window appears. Step 2
Click Show IADs. The configured IADs appear, and a message in the status bar indicating how many IADs have been retrieved (Figure 11–6).
Figure 11–6. IAD Configuration Manager Window with IAD Displayed
11-10
Step 3
Select the IAD on which you want to collect statistics, the option buttons are enabled.
Step 4
Select Errors or Performance. The graphing window appears.
Step 5
Continue with Step 3 in Graphing Statistics on page 11-12.
November 2003
1000-A2-GB21-10
Accessing E1 Links Step 1
Alarms, Events, and Statistics
To access the E1 links statistics:
Click the desired on the Tree View, the right-hand pane changes to the variant tabular view (Figure 11–7).
Figure 11–7. Variant Tabular View Step 2
Select a link ID on which you want to poll statistics.
Step 3
Select Error Graphs or Performance Graphs from the Report menu. – Or – Right-click the highlighted selection and select Errors Graphs or Performance Graphs from the popup menu.
Step 4
November 2003
Continue with Step 3 in Graphing Statistics on page 11-12.
11-11
Alarms, Events, and Statistics
Graphing Statistics
1000-A2-GB21-10
To generate a statistics graph:
Step 1
Select an icon in the Tree View. For example, if you want to generate a graph for a card, select the card icon in the Tree View.
Step 2
Select the type of graph from the Report menu or right-click the appropriate icon. The graphing window similar to Figure 11–8 appears. Graph format selections
Figure 11–8. Graphing Window
11-12
Step 3
Select the items on which you want to poll statistics from the Properties panel by clicking the adjacent box. Or click Select All if you want to poll all items listed. (A maximum of 20 properties can be graphed at a time.)
Step 4
Choose the type of graph you want to generate (format options are a bar graph or a plot).
Step 5
Choose the frequency of the data that will be graphed from the options in the On Line panel (your option is 15 seconds).
November 2003
1000-A2-GB21-10
Step 6
Alarms, Events, and Statistics
Select a method to view your statistical presentation. Your options are Graph or Table.
Note Graphs display absolute and relative values. Clicking Show marks the initial absolute value. Clicking Reset freezes the absolute value, and starts marking new relative values. Subsequent resets add the last relative value to the absolute value, and start marking new relative values.
Step 7
Click Show. JetCraft displays the graph based on the options you selected (Figure 11–9 and Figure 11–10).
Step 8
Click Close to exit this window.
Figure 11–9. Sample Graph Window
November 2003
11-13
Alarms, Events, and Statistics
1000-A2-GB21-10
Figure 11–10. Sample Table Window
11-14
November 2003
C
H
A
P
T
E
R
12
CPX-1000 Maintenance and Services Some maintenance tasks, such as backing up a CPX-1000 database, are performed routinely while others are performed as needed. This chapter provides instructions to perform the following tasks: Backing up CPX-1000 database (page 12-2) Restoring CPX-1000 database (page 12-3) Rebooting the CPX-1000 (page 12-4) Rebooting the MP or CP cards (page 12-5) Setting the CPX-1000 internal clock (page 12-5)) Switching the CP cards (page 12-7) Performing CP switchover (page 12-11) Hot swapping (page 12-11)
November 2003
12-1
CPX-1000 Maintenance and Services
Backing Up CPX-1000 Database Step 1
1000-A2-GB21-10
The backup database is saved as a file image to the MP card. You then transfer the file image via File Transfer Protocol (FTP) to a selected management workstation. To back up CPX-1000 database: Select Backup CPX Configuration from the Services menu. The Backup CPX Configuration window appears (Figure 12–1).
Figure 12–1. Backup CPX Configuration Window Step 2
Type the name of the backup database and click OK.
Note Record the file name in case you perform a restore operation.
Step 3
Transfer the backup file to the management workstation by using FTP. For example: c:\> ftp
Login: anonymous Password: ftp> bin (change to binary mode) ftp> get ftp> quit
12-2
November 2003
1000-A2-GB21-10
Restoring CPX-1000 Database
CPX-1000 Maintenance and Services
If you lose or change a CPX-1000’s database, you can restore it from the original that was backed up to the MP card.
Warning
Restoring a CPX-1000 configuration requires rebooting both the MP and CP cards. Rebooting the CP card interrupts service. To restore a CPX-1000 database: Step 1
Transfer the CPX-1000 configuration file you want to restore by using FTP. For example: c:\> ftp Login: anonymous Password: ftp> bin (change to binary mode) ftp> put ftp> quit
Note Make sure that you are in the same directory as the CPX-1000 configuration file.
Step 2
Select Restore CPX Configuration from the Services menu. The Restore CPX Configuration window appears (Figure 12–2).
Figure 12–2. Reboot CPX Configuration Window Step 3
November 2003
Type the name of the database file to be restored.
12-3
CPX-1000 Maintenance and Services
1000-A2-GB21-10
Step 4
Click OK to restore the configuration. A prompt appears, asking if you want to continue the operation.
Step 5
Click Yes. A prompt appears, asking if you want to reboot the CPX-1000.
Step 6
Click Yes.
Rebooting the CPX-1000 Voice/Data Interruption
When rebooting the CPX-1000, all cards power down gracefully. Calls are dropped immediately.
To reboot the CPX-1000:
12-4
Step 1
Click the
icon from the Tree View.
Step 2
Select Reboot from the Services menu. The following dialog box appears, asking if you want to continue.
Step 3
Click Yes. When the reboot process completes, the following dialog box appears.
Step 4
Click Re-login. Then type your user ID and password in their respective fields when the JetCraft Login window reappears.
November 2003
1000-A2-GB21-10
Rebooting the MP or CP Card
CPX-1000 Maintenance and Services
You can reboot either the MP card or the standby CP card. Rebooting the MP card interrupts the management operation, but it does not affect the call processing functions. Before rebooting the standby CP card, put it to the Locked state (Changing CP Card States on page 12-9). Warning
Rebooting the CP card interrupts service.
To reboot the MP or CP card: Step 1
Click either the MP or CP card icon from the Tree or Shelf views.
Step 2
Select Reboot from the Services menu. A prompt appears, asking if you want to continue.
Step 3
Click Yes to reboot.
Setting the Clock
If the CPX-1000 is stored for an extended period of time and the ambient temperature changes while it is in storage, the CPX-1000 internal clock may require adjustment. To change the time configuration:
Note If MP is not selected, Time Configuration is grayed out.
Step 1
Select MP at the Shelf View or Tree View.
Step 2
Select Time Configuration from the Services menu. – Or – Right-click and select Time Configuration from the popup menu. The Set CPX Time window displays the current time setting (Figure 12–3).
November 2003
12-5
CPX-1000 Maintenance and Services
1000-A2-GB21-10
Figure 12–3. Set CPX Time Window Step 3
Click Select and a calendar appears (Figure 12–4).
Figure 12–4. Day Calendar Step 4
Select the month and year from the drop-down list. Click OK to return to the Set CPX Time window, displaying your date settings.
Step 5
Select the current day by clicking the date in the calendar.
Step 6
Select the time (hour, minutes, and seconds) from drop-down list.
Note JetCraft uses a 24-hour clock.
Step 7
12-6
Click OK to exit the Set CPX Time window.
November 2003
1000-A2-GB21-10
Switching CP Cards
CPX-1000 Maintenance and Services
When a switchover is requested, the CPX-1000 acknowledges the request and issues the appropriate alarms and events of the switchover status. Upon a switchover, a message on the status bar indicates the status of the switchover (active or standby). When the switchover is successful, the previously active card becomes the standby card and the previously standby card is now the active card. Before performing a switchover on a CP card, make sure that the following conditions are present: two CP cards are inserted in their assigned slots there are no alarms on either CP card the states of CP cards if switching from CP-A to CP-B:
States
CP-A
CP-B
Active
Standby
Administrative
Unlocked
Unlocked
Operational
Enabled
Enabled
Primary
Primary
Secondary
the states of CP cards if switching from CP-B to CP-A:
States
November 2003
CP-B
CP-A
Active
Standby
Administrative
Unlocked
Unlocked
Operational
Enabled
Enabled
Primary
Secondary
Primary
12-7
CPX-1000 Maintenance and Services
Ensuring Redundancy
1000-A2-GB21-10
To ensure redundancy on the CPX-1000, both CP cards need to be inserted in their assigned slots. Figure 12–5 shows the slot assignments of CPX-1000 cards. The color shown indicates the states of the cards: green for active and blue for standby. The two CP and an MP cards are located in fixed slot assignments. The primary CP occupies slot 7 with its corresponding primary HSC card in slot 10. The secondary CP occupies slot 9 with its corresponding secondary HSC card in slot 8. The MP card occupies slot 6. Other line cards slot assignments do not have fixed slot assignments and are detected at startup. For a description of individual cards, refer to CPX-1000 Introduction and Technical Description.
Indicates out-of-service administrative state
Primary CP card in slot 7
Secondary CP card in slot 9
Figure 12–5. Shelf View
12-8
November 2003
1000-A2-GB21-10
Changing CP Card States
CPX-1000 Maintenance and Services
A card is locked when a lock icon appears on the card just below the slot number. To change the CP cards administrative states:
Step 1
Select in the Tree View, then select Configure from the Configuration menu. – Or – Right-click on the desired card in the Tree or Shelf View and select Configure. The Card Configuration window appears, displaying the readonly card information (Figure 12–6).
Figure 12–6. CP Card Configuration Window
November 2003
12-9
CPX-1000 Maintenance and Services
Step 2
1000-A2-GB21-10
Select Status. The Status tab appears, displaying the current service state of the card (Figure 12–7).
Notes The Performance Monitoring field (true or false) indicates whether the statistics are available for that card. The Administrative state is only displayed if it can be modified. The Operational state is set to Enabled when the card is discovered.
Figure 12–7. CP Card Configuration—Status Tab
12-10
Step 3
Select the administrative state from the Administrative State drop-down list. Your options are Locked or Unlocked.
Step 4
Click OK. A dialog box appears, asking if you want to change the state.
Step 5
Click Yes.
November 2003
1000-A2-GB21-10
CPX-1000 Maintenance and Services
Performing a CP Switchover Voice/Data Interruption
Calls being set up during a CP switchover are dropped.
To perform a switchover: Step 1
Ensure that the standby CP card is “unlocked” (Changing CP Card States on page 12-9).
Step 2
Select the active card.
Step 3
Select Switchover from the Configuration menu or by rightclicking the active card. A prompt appears, asking if you want to continue the operation.
Step 4
Click Yes to perform the switchover.
Hot Swapping
Hot swapping lets you remove and replace cards without shutting down and reconfiguring the CPX-1000. JetCraft supports hot swapping on all cards. To hot swap a MP card, go to page 12-12 To hot swap CP and HSC cards, go to page 12-13 To hot swap line cards, go to page 12-14
Note Make sure to put on an anti-static wrist wrap when hot swapping cards. Refer to CPX-1000 Voice Services Platform Service for more information.
November 2003
12-11
CPX-1000 Maintenance and Services
Hot Swapping MP Card
12-12
1000-A2-GB21-10
To hot swap the MP card:
Step 1
Back up the current CPX-1000 database (Backing Up CPX-1000 Database on page 12-2).
Step 2
Click the MP card from the Tree or Shelf views.
Step 3
Select Remove Resources from the Configuration menu. A prompt appears, asking if you want to remove all resources associated with the card.
Step 4
Click Yes. The card is removed from the Tree and Shelf views.
Step 5
Remove the physical MP card, followed by its corresponding transition card, from the CPX-1000 shelf.
Step 6
Insert the new transition card, followed by the MP card, and lock them in place using the card ejectors.
Step 7
Select Refresh CPX from the File menu. The new MP card appears in the Tree and Shelf views.
Step 8
Restore the CPX-1000 configuration (Restoring CPX-1000 Database on page 12-3).
November 2003
1000-A2-GB21-10
Hot Swapping CP and HSC Cards
CPX-1000 Maintenance and Services
HSC cards are paired with CP cards. After the HSC card is replaced, pairing with the CP card is automatically restored.
Note Make sure to put on an anti-static wrist wrap when hot swapping cards. Refer to CPX-1000 Voice Services Platform Service for more information.
To hot swap CP and HSC cards: Step 1
Click the CP card icon from the Tree or Shelf view. If hot swapping an active CP or HSC card, continue with
Step 2. If hot swapping a standby CP or HSC card, continue with
Step 3.
November 2003
Step 2
Perform switchover to place the active card in standby (Performing a CP Switchover on page 12-11).
Step 3
Place the CP card to the Locked state (Changing CP Card States on page 12-9).
Step 4
Select Remove Resources from the Configuration menu. A prompt appears, asking if you want to remove all resources associated with the card.
Step 5
Click Yes. The card is removed from the Tree and Shelf views.
Step 6
Remove the physical CP card, followed by its corresponding HSC card, from the CPX-1000 shelf.
Step 7
Insert the HSC card, followed by the CP card, and lock them in place using the card ejectors. (Continue with Step 9 if this is a standby CP or HSC card.)
Step 8
Select Refresh CPX from the File menu. The new cards appear in the Tree and Shelf views.
Step 9
Place the CP card to the Unlocked state (Changing CP Card States on page 12-9).
12-13
CPX-1000 Maintenance and Services
Hot Swapping Line Cards
1000-A2-GB21-10
Line cards are paired with their corresponding transition cards. Line cards include: ATM DS-3 E1 ECAC STM-1
Note Make sure to put on an anti-static wrist wrap when hot swapping cards. Refer to CPX-1000 Voice Services Platform Service for more information.
To hot swap a line card:
12-14
Step 1
Click a line card that you want to hot swap from the Tree or Shelf View.
Step 2
Place the selected line card to the Locked state (Changing CP Card States on page 12-9).
Step 3
Select Remove Resources from the Configuration menu. A prompt appears, asking if you want to remove all resources associated with the card.
Step 4
Click Yes. The card is removed from the Tree and Shelf views.
Step 5
Remove the physical line card first, followed by its corresponding transition card, from the CPX-1000 shelf.
Step 6
Insert the new physical transition card, followed by the line card, and lock them in place, using the card ejectors.
Step 7
Select Refresh CPX from the File menu. The new card appears in the Tree and Shelf views. The state of the card automatically changes to “unlocked,” and all resources for that card are restored.
November 2003
C
H
A
P
T
E
R
13
IAD Status and Maintenance This chapter provides instructions to perform the following tasks for IADs: Downloading IAD Software (page 13-1) Automated IAD software download (page 13-4) Automatic and Manual IAD configuration download
(page 13-11) Remote restarting of IADs (page 13-14) Monitoring IAD port status (page 13-17)
Downloading IAD Software Step 1
To download IAD software:
Select IAD Manager from the Configuration menu. – Or – Right-click Manager.
on the Tree View or Map View and select IAD
– or – Click
at the toolbar.
The IAD Configuration Manager window appears. Step 2
November 2003
Click Show IADs. The configured IADs appear and a message in the status bar indicates how many IADs have been retrieved (Figure 13–1)
13-1
IAD Status and Maintenance
1000-A2-GB21-10
Figure 13–1. IAD Configuration Manager Window with IADs Displayed
Note Verify that the IAD operational state is enabled before downloading IAD software to the device. The Admin state can be Locked or Unlocked.
Step 3
13-2
Click Download. The IAD Software Download dialog (Figure 13–2) displays the IAD software filename, current version of the IAD (for example, 2.2.1), and Available Versions.
November 2003
1000-A2-GB21-10
IAD Status and Maintenance
Figure 13–2. IAD Software Download dialog Step 4
Select the appropriate version from the Available Versions field.
Step 5
Select Restart IAD after download completes.
Note To enable the Delay restart of IAD until no active calls option, you must first select the Restart IAD after download completes option. (The second option is conditional or dependent upon the first item being selected.)
Step 6
Select OK to download the IAD software to the specified IAD.
Step 7
Click Download Status on the Update IAD window (Figure 8–19 on page 8-22). The Download Status popup window displays the current IAD download status (successful, in-progress, etc.).
November 2003
13-3
IAD Status and Maintenance
Automated IAD Software Download
1000-A2-GB21-10
To enable support for IAD Auto Download, you must enable the Download Status for both the JetVision Server and the CPX.
Notes Before you use the Automated IAD Software Download tool, you must use the CPX IAD Firmware Loader (located on the JetCraft CD) to load the IAD software into the correct directory on the MP. See Storing IAD Software on the CPX-1000 on page 13-6.
To enable or disable this feature for the JetVision Server, follow these steps. Step 1
Select Configure Global IAD Auto Download from the Services menu.
Step 2
Select Enable or Disable.
Step 3
Click OK.
Figure 13–3. Global IAD Auto Download Status Screen To enable or disable this feature for a CPX, follow these steps:
13-4
Step 1
Click the desired CPX-1000 icon from the Tree View.
Step 2
Select Configure from the Configuration menu.
November 2003
1000-A2-GB21-10
Step 3
IAD Status and Maintenance
Select the IAD Auto Download tab.
Figure 13–4. CPX IAD Auto Download Configuration Status Step 4
In the CPX IAD Auto Download Status section select Enable or Disable.
Step 5
Choose which system to base the IAD Auto Download Schedule on. You can choose to have the schedule time based on the CPX1000 or the JetVision Server time.
Step 6
Configure the start and stop time to have the download occur. Choose the Download Start Time: (0:00 - 23:00) Choose the Download End Time: (0:00 - 23:00)
Notes Download start and end times cannot be the same.
November 2003
13-5
IAD Status and Maintenance
Step 7
Storing IAD Software on the CPX-1000
1000-A2-GB21-10
Click OK.
This section describes how to load IAD software onto the CPX1000. The IAD software must be loaded onto the CPX-1000 to be able to use the Jetvision automated or manual IAD software download feature. To install an IAD firmware version on the CPX-1000:
Step 1
Copy the CPX IAD Firmware Installer folder from the Jetcraft CD to a hard drive. From the CPX IAD Firmware Installer folder on the hard drive, Run Setup.exe. The CPX-1000 Configuration Panel appears.
Figure 13–5. CPX-1000 Configuration Panel
13-6
November 2003
1000-A2-GB21-10
Step 2
IAD Status and Maintenance
Enter the IP Address of the CPX that the IAD firmware is to be installed on. Click on Next. The CPX-1000 IAD Manufacturer Panel appears.
Figure 13–6. CPX-1000 IAD Firmware Manufacturer Panel Step 3
Enter the Manufacturer, Model, and Version of the IAD firmware to be installed. All three fields are required and must exactly match the manufacturer and version returned by the IAD. The fields are casesensitive.
November 2003
13-7
IAD Status and Maintenance
Step 4
1000-A2-GB21-10
Click on Next. The CPX-1000 IAD Firmware Location Panel appears.
Figure 13–7. Location of IAD Firmware Panel
13-8
November 2003
1000-A2-GB21-10
Step 5
IAD Status and Maintenance
Enter the name of the directory where the firmware is located. Click on Next. The CPX-1000 IAD Firmware Confirmation Panel appears.
Figure 13–8. IAD Firmware Manufacturer Confirmation Panel
November 2003
13-9
IAD Status and Maintenance
Step 6
1000-A2-GB21-10
Verify that the information is correct. Click on Next. The CPX-1000 IAD Firmware Install panel appears as the IAD Firmware is installed on the CPX.
Figure 13–9. IAD Firmware Installation Panel Step 7
When installation is complete, the CPX-1000 IAD Firmware Completion panel appears.
Figure 13–10. IAD Firmware Installation Complete Panel
13-10
November 2003
1000-A2-GB21-10
Step 8
IAD Configuration Download
IAD Status and Maintenance
Click on Exit.
The IAD Configuration Download feature allows a configuration file to be downloaded automatically to an IAD. The configuration file allows the IAD PPPOA user ID and password to be set. This feature allows an IAD’s settings to be updated without having to manually change these settings at the customer’s site. Jetvision automatically generates a configuration file that includes the provisioned PPPOA user ID and password for an IAD. This feature has two modes: automatic and manual. Automatic mode detects the first time the IAD comes online and automatically downloads the configuration file to the IAD. After the configuration download is complete, the IAD is restarted. In the manual mode the configuration can be downloaded at any time by the user using the IAD Manager screen.
Automatic IAD Configuration Download
To enable support for Automatic IAD Configuration Download, you must enter a PPPOA user ID and password when provisioning an IAD. (See Chapter 9, IADs Provisioning.) When the IAD comes online for the first time, the CPX-1000 automatically downloads the provisioned PPPOA user ID and password to the IAD. After a successful configuration download, the IAD is restarted and the configuration is available.
Manual IAD Configuration Download
To manually download a configuration file, follow these steps.
Step 1
Click on a CPX-1000 from the Tree View and expand the tree by clicking the plus (+) sign.
Step 2
Click on a CPX-1000 icon in the Tree view.
Step 3
Select IAD Manager from the Configuration menu. – Or – Right-click on the Tree View or Map View and select IAD Manager from the popup menu. – Or – Click
November 2003
on the toolbar.
13-11
IAD Status and Maintenance
1000-A2-GB21-10
The IAD Configuration Manager window appears (Figure 13–11).
Figure 13–11. IAD Configuration Manager Window Step 4
Click on Show IADs. A list of available IADs appears (Figure 13– 12).
Figure 13–12. IAD Configuration Manager Window with IADs Shown
13-12
November 2003
1000-A2-GB21-10
Step 5
IAD Status and Maintenance
Select IADs for which you want to change the configuration. Ensure that the operational state of the IADs you select is Enabled and the administrative state is Unlocked. (See Chapter 9, IADs Provisioning.)
Notes To select multiple IADs, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select IADs in a random order. The IAD model number and current code version must be identical before performing a download.
Step 6
Click Download Config. The IAD Configuration Download confirmation screen appears.
Figure 13–13. IAD Download Config Confirmation Window
November 2003
13-13
IAD Status and Maintenance
Step 7
1000-A2-GB21-10
Select Yes or Yes To All. The configuration download begins. The status of the configuration download is displayed at the bottom of the IAD Manager.
Figure 13–14. IAD Configuration Manager Window with IAD Config Download status
Remote Restarting of IADs
JetCraft allows remote restarting of IADs. To remote restart an IAD:
Step 1
Click a CPX-1000 from the Tree View and expand the tree by clicking the + sign.
Step 2
Click a CPX-1000 icon in the Tree view.
Step 3
Select IAD Manager from the Configuration menu. – Or – Right-click on the Tree View or Map View and select IAD Manager from the popup menu. – Or – Click
13-14
on the toolbar.
November 2003
1000-A2-GB21-10
IAD Status and Maintenance
The IAD Configuration Manager window appears (Figure 13–15). Click here to display IADs
Figure 13–15. IAD Configuration Manager Window
November 2003
13-15
IAD Status and Maintenance
Step 4
1000-A2-GB21-10
Click Show IADs. A list of available IADs appears (Figure 13–16).
Figure 13–16. IAD Configuration Manager Window with IADs Shown Step 5
Select the IAD you would like to restart.
Notes To select multiple IADs, hold down the Shift or Ctrl key while making your selections. Using the Shift key lets you make your selections in contiguous order; the Ctrl key lets you select IADs in a random order.
Step 6
Click the Restart IAD button. The Restart IAD dialog box appears (Figure 13–17).
Figure 13–17. Restart IAD Dialog Box
13-16
November 2003
1000-A2-GB21-10
Step 7
IAD Status and Maintenance
Select Yes.
Note To immediately reboot the IAD, you must deselect Delay restart until no active calls.
Step 8
Click IAD Restart Status. The IAD Restart Status pop-up window displays the current IAD restart status (Figure 13–18).
Figure 13–18. IAD Restart Status Pop-up Window
Monitoring IAD Port Status
JetCraft allows status monitoring of IAD ports. IAD port monitoring status consists of the call state (allocated/deallocated), hook state (on/off), and the E1 time slot when calls are being processed.
Note Port status is not updated as calls transition through the call states.
To view IAD port status: Step 1
Click a desired CPX-1000 icon in the Tree View.
Step 2
Select IAD Manager from the Configuration menu. – Or – Right-click on the Tree View or Map View and select IAD Manager from the popup menu. – Or –
November 2003
13-17
IAD Status and Maintenance
1000-A2-GB21-10
Click
at the toolbar.
The IAD Configuration Manager window appears (Figure 13–19). Click here to display IADs
Figure 13–19. IAD Configuration Manager Window
13-18
November 2003
1000-A2-GB21-10
Step 3
IAD Status and Maintenance
Click Show IADs. The configured IADs appear, and a message in the status bar indicates how many IADs are retrieved (Figure 13–20).
Number of IADs retrieved
Figure 13–20. IAD Configuration Manager Window with IADs Displayed
November 2003
13-19
IAD Status and Maintenance
Step 4
1000-A2-GB21-10
Select the IAD you want to view. Click Modify. The IAD Modification window appears (Figure 13–21).
Figure 13–21. IAD Modification Window
Note If you omit Step 3, click the State tab and lock the IAD.
Step 5
13-20
Select the Port Status tab. The status of each IAD port is shown (Figure 13–22).
November 2003
1000-A2-GB21-10
IAD Status and Maintenance
Figure 13–22. IAD Modification − Port Status Window
November 2003
13-21
IAD Status and Maintenance
13-22
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
R
A
JetCraft Menu Map
The following menu map provides a linear, hierarchical overview of the tasks and sub-tasks associated with the JetCraft main window.
November 2003
A-1
JetCraft Menu Map
1000-A2-GB21-10
Log On (User ID/Password) Main Menu
File Menu
Configuration Menu
Refresh CPX
Confiugre
Exit
Switchover Create V5.2 IG Create V5.1 IG Modify IG Delete IG E1 Link ID Check
Services Menu
Reports Menu
Backup CPX Configuration
Error Graphs
Contents & Index
Performance Graphs
About
Restore CPX Configuration
Line Error Graphs Alarm Polling Section Error Graphs Interval Configuration Path Error Graphs V5 Display Configuration
PSTN Restart
Configure Global System
Create Variant
IP Configuration
Modify Variant
Time Configuration
Delete Variant
Reboot
Switch Variant
Create CPX User
Verify Variant
Change CPX Password
PG Swap Path Trace Create ISDN Port Template
Help Menu
CPX User Administration
ISDN Port Template Manager Create IAD Profile IAD Profile Manager Create IAD IAD Manager Clock Synch Remove Resource 02-17313
Figure A–1. JetCraft Menu Map
A-2
November 2003
C
H
A
P
T
E
R
B
Statistics Definitions
Table B–1 describes the error statistics and Table B–2 describes the performance statistics.
Table B–1. Error Statistics Definitions Error Statistics
Description
CPX Statistics
Assembly errors
Number of Assembly errors
Blocked incalls
Number of Blocked incalls
Blocked outcalls
Number of Blocked outcalls
CRC errors
Number of CRC errors
IADs Down
Number of IADs down
ATM DS-3
Loss of signal
No incoming signal is detected by the received end.
Loss of frame
No incoming frame is detected by the received end.
Far end receive failure
Number of far-end-receive failures
Red count
Number of red counts.
Out of cell delineation
Number of out-of-cell delineations.
Loss of cell delineation
Number of cell delineation losses.
Far end alarm indication
Number of far-end-alarm indications.
November 2003
B-1
Statistics Definitions
1000-A2-GB21-10
Table B–1. Error Statistics Definitions (Continued) Error Statistics
Description
ATM STM-1
AAL1 byte CRC errors
Number of AAL1 CRC errors
AAL1 byte parity errors
Number of AAL1 byte parity errors
AAL1 byte seq errors
Number of AAL1 byte sequence number errors
Clock generation failures
Number of times the clock generation module failed
Ref cell loss
Number of timing reference cells lost
Ref cell out of sync
Number of times reference cells went out of sync
TDM master clocks absent
Number of times TDM clock became absent
IAD Subscribers Statistics
Assembly errors
Number of Assembly errors
Blocked incalls
Number of Blocked incalls
Blocked outcalls
Number of Blocked outcalls
CRC errors
Number of CRC errors
E1 link Statistics
B-2
Alarm Indication Signal Seconds—last 15 minutes
Number of one-second intervals with one or more incoming AIS signals detected in the last 15 minutes
Bipolar Violations—last 15 minutes
Number of Bipolar Violations in the last 15 minutes
Bursty Errored Seconds— last 15 minutes
Number of one-second intervals containing one or more bursty events in the last 15 minutes
Controlled Slip Seconds— last 15 minutes
Number of Controlled Slips Seconds in the last 15 minutes
Controlled Slips—last 15 minutes
Number of Controlled Slips in the last 15 minutes
Degraded Minutes—last 15 minutes
Number of Degraded Minutes in the last 15 minutes
November 2003
1000-A2-GB21-10
Statistics Definitions
Table B–1. Error Statistics Definitions (Continued) Error Statistics
Description
Errored Seconds—last 15 minutes
Number of one-second intervals with at least one line condition in the last 15 minutes
Excessive Zeroes—last 15 minutes
Number of Excessive Zeroes in the last 15 minutes
Line Coding Violations— last 15 minutes
Number of times the received DS1 signal contained a bipolar violation (BPV) or an excessive number of zeroes (EXZ)
Line Errored Seconds— last 15 minutes
Number of one-second intervals with a least one line code violation
Out Of Frame Seconds— last 15 minutes
Number of Out Of Frame Seconds in the last 15 minutes
Path Coding Violations— last 15 minutes
Number of times the received DS1 signal contained a bipolar violation (BPV) or an excessive number of zeroes (EXZ)
Severely Errored Framing Seconds —last 15 minutes
Number of one-second intervals containing one or more severely errored framing (SEF) events in the last 15 minutes
Severely Errored Seconds —last 15 minutes
Number of one-second intervals with 15 or more line code violations, as well as when the device receives an incoming OOF or AIS signal in the last 15 minutes
Unavailable Seconds—last 15 minutes
Number of one-second intervals during which the service is unavailable, determined by a transmission failure condition in the last 15 minutes
November 2003
B-3
Statistics Definitions
1000-A2-GB21-10
Table B–2. Performance Statistics Definitions Performance Statistics
Description
CPX Statistics
Active calls
Number of active calls
Ctrl cells rcvd
Number of Ctrl cells received
Ctrl cells sent
Number of Ctrl cells sent
Cumulative calls
Number of cumulative calls
IADs Provisioned
Number of IADs provisioned
IADs Up
Number of IADs up
Peak calls
Number of peak calls
MP Card
B-4
Physical memory (MB)
Total RAM expressed in megabyte
Available physical memory (MB)
Available RAM expressed in megabyte
Physical memory usage (MB)
RAM usage expressed in megabyte
Physical memory usage (percent)
RAM usage expressed in percentage
CPU usage (percent)
CPU usage expressed in percentage
Disk size (MB)
Total hard disk space expressed in megabyte
Disk usage (MB)
Hard disk space usage expressed in megabyte
Disk usage (percent)
Hard disk space usage expressed in percentage
Free disk space (MB)
Available hard disk space expressed in megabyte
Page size (MB)
Total page size expressed in megabyte
Free page size (MB)
Available page size expressed in megabyte
Page usage (MB)
Page size usage expressed in megabyte
Page usage (percent)
Page size usage expressed in percentage
November 2003
1000-A2-GB21-10
Statistics Definitions
Table B–2. Performance Statistics Definitions (Continued) Performance Statistics
Description
Protection Group
Automatic switches
Number of switchovers invoked by the CPX-1000
Manual switches
Number of switchovers invoked by users
Switches to Primary
Number of switchovers invoked by the Primary member
Switches to Secondary
Number of switchovers invoked by the Secondary member
STM-1 Port Statistics
Ce is rcvd
Number of cells received
Ce is sent
Number of cells sent
Open Rx VCs
Number of open Rx VCs
Open Tx VCs
Number of open Tx VCs
IADs Statistics
Active calls
Number of active calls
Cells rcvd
Number of cells received
Cells sent
Number of cells sent
Ctrl cells rcvd
Number of Ctrl cells received
Ctrl cells sent
Number of Ctrl cells sent
Cumulative calls
Number of cumulative calls
Peak calls
Number of peak calls
E1 link Statistics
DS0s In Use
November 2003
How many DS0s (channels) on a DS1 (E1 lines) are currently active (a call is in progress)
B-5
Statistics Definitions
B-6
1000-A2-GB21-10
November 2003
C
H
A
P
T
E
C
R
Alarm Summary
Table C–1 provides a summary of alarms.
Note The CPX-1000 database alarm can be cleared only by Paradyne. Call Technical Support at 1-800-870-2221 (in U.S. or Canada) or 1-727-530-2340 (worldwide) to clear the CPX-1000 database alarm.
Table C–1. Alarm Summary Affected Element
Alarm Message
Description
Severity
Triggered by
CPX-1000
General system alarm
Indicates general system alarm.
Major
CORE
CPX is down
Indicates CME lost connection to all CPs.
Critical
CME
Error in database
Indicates error in database during startup and initialization.
Major
CME
November 2003
C-1
Alarm Summary
1000-A2-GB21-10
Table C–1. Alarm Summary (Continued) Affected Element
Alarm Message
Description
Severity
Triggered by
CP card
Lost connection to a CP
Indicates lost connection to CP.
Major
CME
CP lost heartbeat to peer
Indicates CP lost heartbeat to peer CP.
Major
CORE
CP found the peer CP faulty
Indicates CP found the peer CP faulty.
Major
CORE
CP detected that the peer CP has been removed
Indicates CP has detected the removal of peer CP.
Major
CORE
IAD unknown alarm
Indicates the IAD has not been initialized or recognized.
Major
CORE
Lost link with IAD
Indicates a lost link with the IAD.
Major
CORE
Provisioned ports are greater than the reported ports
Indicates the number of provisioned ports is greater than the number of reported ports.
Major
CME
Voice Quality Alarm
VQA is triggered whenever ATM overruns and underruns exceed predefined thresholds
Minor
CORE
IAD Ports
IAD port alarm
Indicates the IAD port has not been initialized or recognized.
Major
CORE
ATM Ports
— Lost ATM connection
Indicates lost ATM connection between the ATM card and ATM port.
Critical
CORE
— No adapter is driving the TDM master clock
Indicates no adapter is driving the TDM master clock between the ATM card and ATM port.
Critical
CORE
IAD
C-2
November 2003
1000-A2-GB21-10
Alarm Summary
Table C–1. Alarm Summary (Continued) Affected Element
ATM Ports
Protection Group
Alarm Message
Description
Severity
Triggered by
— ATM adaptive recovery scheme alarm
Indicates an ATM adaptive recovery scheme alarm between the ATM card and ATM port.
Critical
CORE
— SONET lost signal
Indicates SONET lost signal between the ATM card and ATM port.
Critical
CORE
— SONET lost frame
Indicates SONET lost frame between the ATM card and ATM port.
Critical
CORE
— SONET path lost pointer
Indicates SONET path lost pointer between the ATM card and ATM port.
Critical
CORE
— OAM Line AIS alarm
Indicates OAM Line AIS alarm between the ATM card and ATM port.
Critical
CORE
— OAM Path AIS alarm
Indicates OAM Path AIS alarm between the ATM card and ATM port.
Critical
CORE
— OAM Line RDI alarm
Indicates OAM Line RDI alarm between the ATM card and ATM port.
Critical
CORE
— Unknown alarm
Indicates the ATM card/ port has not been initialized or recognized.
Critical
CORE
The does not exist
Indicates the card does not exist during startup verification against card information from discovery.
Critical
CME
The does not exist
Indicates the port does not exist during startup verification against card information from discovery.
Critical
CME
November 2003
C-3
Alarm Summary
1000-A2-GB21-10
Table C–1. Alarm Summary (Continued) Affected Element
V5 Interface Group
Alarm Message
Description
Severity
Triggered by
V5 Interface failure: Out of Service
Indicates the V5 Interface is out of service.
Critical
CORE
V5 Link ID Check Failed
Indicates the V5 link ID check failed.
Major
CORE
V5 PSTN LAP V5 Failed
Indicates PSTN LapV5
Major
CORE
Minor
CORE
Minor
CORE
Minor
CORE
session failed.
C-4
V5 Control LAP V5 Session Failed
Indicates link control
V5 Protection LAP V5 Session Failed
Indicates protection LapV5
V5 BCC LAP V5 Session Failed
Indicates BCC LapV5
Bearer Capability Control, Control and/or Link Control Lap V5 Session Failed
Indicates BCC, control, and/or link control Lap session failed.
Minor
CORE
V5 stack initialization failure
Indicates V5 Interface startup failed.
Critical
CORE
V5 Variant SwitchOver failed
Indicates V5 variant switchover failed.
Critical
CORE
V5 Variant SwitchOver start
Indicates V5 variant switchover started.
Minor
CORE
LapV5 session failed session failed. session failed
November 2003
Index
A accelerated alignment 6-2 access restriction 4-1 active variant 6-14 adding V5.1 Interface Groups 6-3 V5.2 Interface Groups 6-7 adjusting the CPX-1000 internal clock 12-5 Admin state E1 link 6-2, 6-28 port, changing 7-4 admin state CP cards 12-10 admin state options 5-2 administrative state IAD 9-2 IAD level 9-3 port level 9-3 administrative states CP cards 12-9 alarm summary 11-1 alarmed indication 3-5 alarms color and states 11-2 color indication 3-5 colors indication 11-1 display 11-1 levels of severity 3-5 sorting 11-3 sortng 3-5 viewing 3-5 alarms summary viewing 11-3 ATM 9-7, 9-14
November 2003
ATM DS-3 error statistics summary 11-7 ATM Protection Group assigning members 7-2 error statistics summary 11-6 filtered by 9-24, 9-26 searched by 9-24, 9-26 statistics polling 11-9 ATM redundancy 7-1 Automated IAD Software Download tool 13-4 automatic configuration download 13-11
B back up CPX-1000 database 12-2 block deferred 6-29 block forced 6-29 block not deferred 6-29 bulk IAD deletion 9-23
C cable type 7-3 calendar setting 12-6 Call Admission Control (CAC) performed by CPX 10-1 CDV setting value 5-9 Cell Delay Variation. See also CDV Change Password window 4-2 changing administrative states CP cards 12-9 changing CRC value 5-10 changing E1 link states 6-28, 6-30 changing port admin states 7-4
I-1
Index
changing user password 4-2, 4-3 changing VCI value 5-7 channel type V5.1 8-8 V5.2 8-8 checking variant 6-20 checking version information 2-8 clock setting 12-5 clock source 5-11 collecting statistics IAD 11-10 compatibility different versions 2-8 configuration download 13-11 connection LAN 1-4 WAN 1-4 connection lost 2-10 country setting 5-3, 5-4 CP cards administrative states 12-9 hot swap 12-13 primary slot 12-8 reboot 12-5 redundancy checking 12-8 secondary slot 12-8 slot assignments 12-8 switching 12-11 CPX users deleting 4-7 modifying 4-5
1000-A2-GB21-10
CPX-1000 5-2 admin states 5-2 backing up database 12-2 configurable parameters 5-2 CP cards reboot 12-5 default Gateway 5-2, 5-5 error statistics summary 11-6 ID 5-2 IP address 5-1 IP address modification 5-5 MP card reboot 12-5 name 5-2 operational states 5-3 parameter modification 5-3 performance statistics summary 11-6 reboot 12-4 redundancy 12-8 refresh after changes 5-13 restoring database 12-3 subnet mask 5-1, 5-5 subnet mask modification 5-5 subnet mask, subnet mask 5-2 CPX-1000 access restriction 4-1 CPX-1000 database backing up 12-2 restore 12-3 CPX-1000 parameters reviewing 5-5 CRC 5-10 creating IAD 9-4, 9-11 IAD Profiles 8-2 ISDN port template 8-7 V5.1 Interface Groups 6-3 V5.2 Interface Groups 6-7 variant 6-15 Critical alarms 11-2 CRV 9-25 customizing search by IAD fields 9-23
D decimal display V5 6-3
I-2
November 2003
1000-A2-GB21-10
default 4-1 IP address 5-1 password 2-8, 4-1 subnet mask 5-1 user ID 2-8, 4-1 default Gateway modification 5-5 default path 2-4 Delete IAD dialog box 9-22 deleting CPX users 4-7 IAD 9-21 IAD Profiles 8-5 Interface Groups 6-13 ISDN port template 8-11 JetCraft users 4-7 Protection Group 7-5 variant 6-21 downloading IAD software 13-1
E E1 link status 6-30 E1 link adding 6-23 assignment, V5.1 IG 6-5 assignment, V5.2 IG 6-9 error statistics summary 11-8 performance statistics summary 11-8 removing 6-25 statistics polling 11-11 E1 link ID check 6-27 E1 link states 6-2, 6-28 block deferred 6-29 block forced 6-29 block not deferred 6-29 changing 6-28, 6-30 error statistics 11-6 error statistics summary 11-6 events message display 3-5
F File Transfer Protocol 12-2, 12-3 filtering fields, IAD 9-23 forced switchover 12-11 Frame Relay 9-7, 9-14
November 2003
Index
FTP 12-2, 12-3
G Gateway 5-2 gateways displaying default CPX 5-5 generating statistics 11-12 GR-303 Interface Groups 6-1
H hardware requirement JetCraft 2-2 hexidecimal display V5 6-3 hot swapping CP cards 12-13 HSC cards 12-13 line cards 12-14 MP card 12-12 HSC cards hot swap 12-13 slot assignments 12-8
I IAD admin states 9-2 automated software download 13-4 bulk deletion 9-23 configuration download 13-11 creating 9-4, 9-11 customize field filtering 9-23 customize search 9-23 deleting 9-21 error statistics summary 11-7 filtering by field 9-23 hardware model 9-25 modification 9-18 monitor port status 13-17 performance statistics summary 11-7 remote restart 13-14 searching by field 9-23 statistics collecting 11-10 IAD Profiles creating 8-2 deleting 8-5 modifying 8-3 removing 8-5
I-3
Index
IAD software download 13-1 icons 3-2 toolbar 3-2 installation default path 2-4 hardware requirement 2-2 protected-mode memory 2-6 installation directory destination 2-4 installation requirement Windows environment 2-6 installing JetCraft 2-2 installing on Windows 2-6 Interface Group maximum number allowed 6-1 interface group configurable parameters 6-2 Interface Groups 6-19 deleting 6-13 filtered by 9-24, 9-25, 9-26 maximum number allowed 6-1 removing 6-13 searched by 9-24, 9-25, 9-26 internal clock 12-5 IP address 5-2 changing 5-5 default 5-1 modification 5-5 modifying 5-5 IP addresses displaying CPX 5-5 ISDN port template configurable parameters 8-6 creating 8-7 deleting 8-11 modifying 8-9 removing 8-11
I-4
1000-A2-GB21-10
J JetCraft iconic views 3-2 installation 2-2 local connection 1-4 Main View 3-2 reconnecting 2-10 remote connection 1-4 removal 2-11 roadmap 2-10 task flow 2-10 user group 4-1 version checking 2-8 JetCraft users deleting 4-7 modifying 4-5
L LE ID 6-2 hexidecimal display 6-3 line cards hot swap 12-14 local connection 1-4
M Major alarms 11-2 manual configuration download 13-11 maximum number allowed Interface Groups 6-1 memory requirement for Windows 2-7 menu functions Configuration menu 3-7 File menu 3-6 Help menu 3-9 Report menu 3-9 Services menu 3-8 messages color indication 3-5 Minor alarms 11-2 Modify IAD window 9-20, 13-20 Modify User window 4-6
November 2003
1000-A2-GB21-10
modifying 6-19 CPX users 4-5 CPX-1000 parameters 5-3 default Gateway 5-5 IAD 9-18 IAD Profiles 8-3 Interface Groups 6-19 IP address 5-5 ISDN port template 8-9 JetCraft users 4-5 subnet mask 5-5 variant 6-19 monitoring IAD port status 13-17 MP card hot swap 12-12 performance statistics summary 11-6 reboot 12-5 slot assignments 12-8 multiple ports selection 6-9, 6-17, 6-25, 6-26
N Network Resource Manager 10-1 NRM 10-1 defining resources 10-2
O Operational state E1 link 6-2, 6-28 operational state options 5-3
P password 4-1 changing 4-2, 4-3 default 2-8 performance statistics 11-6 performance statistics summary 11-6 physical link number V5.1 8-8 V5.2 8-8 ports multiple selection 6-9, 6-17, 6-25, 6-26 primary link assignment Protection Group 6-10 protected-mode memory 2-7
November 2003
Index
Protection Group assigning primary link 6-10 assigning secondary link 6-10 cable selection 7-3 deleting members 7-5 error statistics summary 11-6 filtered by 9-24, 9-26 members assignment 7-2 members removal 7-5 members switched 7-4 searched by 9-24, 9-26 statistics polling 11-9 switching members 7-4 provisioning network resources 10-2 PSTN restart 6-14
R reboot 5-7 CP cards 12-5 CPX-1000 12-4 MP card 12-5 redundancy CP cards 12-8 redundancy checking 1-2 refreshing CPX-1000 5-13 relogin 2-10 remote connection 1-4 remote restarting of IADs 13-14 removing earlier version 2-11 IAD Profiles 8-5 Interface Groups 6-13 ISDN port template 8-11 JetCraft 2-11 Protection Group 7-5 third-party software 2-11 restore CPX-1000 database 12-3
S searching fields, IADs 9-23 secondary link assignment Protection Group 6-10 serial numbers CPX-1000 5-5 setting clock source priority 5-11
I-5
Index
setting CRC value 5-10 setting the CPX-1000 internal clock 12-5 setting VCI value 5-7 signaling protection 6-1 assigning primary link 6-10 assigning secondary link 6-10 slot assignments CP cards 12-8 HSC cards 12-8 MP card 12-8 slot number 3-2 sorting alarms 11-3 standby variant 6-14 statistics error 11-6 graphing 11-12 IADs 11-10 performance 11-6 statistics generation 11-12 statistics polling E1 link 11-11 error 11-12 performance 11-12 statistics summary 11-6 status display 3-5 subnet mask changing 5-5 default 5-1 displaying CPX 5-5 modification 5-5 modifying 5-5 switching CP cards 12-11 Protection Group members 7-4 variant 6-22 switching over CP cards 12-7 switchover voice traffic affected 12-7
T third-party software removing 2-11 time adjustment 12-5 toolbar icons description for 3-2
I-6
1000-A2-GB21-10
U user access 4-2 user access levels 4-2 user group definition 4-2 user ID default 2-8, 4-1 user privileges Admin 4-2 Operations 4-2 Reports 4-2
V V5 display changing 6-3 V5 reprovisioning 6-14 V5.1 channel type 8-8 physical link number 8-8 V5.1 interface creating IAD 9-11 V5.1 Interface Groups adding 6-3 creating 6-3 E1 link assignment 6-5 V5.2 channel type 8-8 E1 links supported 6-1 physical link number 8-8 protection groups 6-1, 6-10 signaling protection 6-1, 6-10 V5.2 interface creating IAD 9-4 V5.2 Interface Groups adding 6-7 creating 6-7 E1 link assignment 6-9 variant 6-2 active 6-14 checking 6-20 creating 6-15 deleting 6-21 modifying 6-19 restrictions 6-15 standby 6-14 switching 6-22 verifying 6-20 VCI 5-7, 9-25
November 2003
1000-A2-GB21-10
version removal 2-11 version checking 2-8 viewing alarms summary 11-3 E1 link status 6-30 VPI 9-7, 9-14
November 2003
Index
W Windows installation requirement 2-6 protected-mode memory 2-7
I-7
