Transcript
INSTALLATION INSTRUCTIONS Istruzioni di installazione Installatie-instructies Instructions d´installation
Instrucciones de instalación Installationsanleitung Instruções de Instalação
K1W110
K1W220
K1W22H
K1W120 K1S120
K1S220
K1S22H
K1W/K1S Wall Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
K1W/K1S Series
K1W/K1S Series
Installation Instructions
DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
WARNING: Use this mounting system only for its intended
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
WARNING: Exceeding the weight capacity can result in
DEFINITIONS MOUNTING SYSTEM: A MOUNTING SYSTEM is the primary Chief product to which an accessory and/or component is attached.
use as described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.
WARNING: Do not use this product outdoors.
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the K1W/K1S Series Monitor Arm up to (and including) the display does not exceed the weight limits listed below. Use with products heavier than the maximum weight indicated may result in collapse of the mounting system and its accessories causing possible injury.
ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it.
MODEL
Max Weight Allowed for EACH Display
Max Weight Capacity of Mounting System
K1W110
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
50 lbs
(11.34 kg)
(22.68 kg)
25 lbs
50 lbs
(11.34 kg)
(22.68 kg)
9 lbs
18 lbs
(4.08 kg)
(8.16 kg)
9 lbs
18 lbs
(4.08 kg)
(8.16 kg)
COMPONENT: A COMPONENT is an audiovisual item designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.
K1W120
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. K1S120
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
K1W220
K1S220
K1W22H
IMPORTANT SAFETY INSTRUCTIONS! WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all mounting systems are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this mounting system can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this mounting system is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the mounting system.
2
K1S22H
--SAVE THESE INSTRUCTIONS!--
Installation Instructions
K1W/K1S Series
DIMENSIONS K1W110
TILT RANGE 75 UP 10 DOWN
INTERFACE ROTATION RANGE 90
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
DYNAMIC HEIGHT ADJUST RANGE 14.07 1.07 357.4 27.2
K1W120 1.38 34.9
6.75 171.5
DYNAMIC LIFT ARM LENGTH RANGE STRAIGNT = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9
1.97 50.1
TILT RANGE 75 UP 10 DOWN
INTERFACE ROTATION RANGE 90
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
DYNAMIC HEIGHT ADJUST RANGE 23.80 10.80 604.6 274.4
3.22 81.7
1.36 34.4
3
K1W/K1S Series
Installation Instructions
K1S120
2.01 51.1
6.75 171.5
DYNAMIC LIFT ARM LENGTH RANGE STRAIGNT = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9
1.97 50.1
TILT RANGE 75 UP 10 DOWN
INTERFACE ROTATION RANGE 90
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
0.22 5.6 HOOK TIP DISTANCE RANGE 3.55 2.05 90.3 52.2
DYNAMIC HEIGHT ADJUST RANGE 17.50 4.50 444.4 114.2
HOOK BASE DISTANCE RANGE 4.06 2.56 103.2 65.1
6.08 154.5
K1W220 0.50 12.7
DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN
1.38 34.9
UP 10 DOWN
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75 INTERFACE ROTATION RANGE 90
3.22 81.7
1.36 34.4
4
Installation Instructions
K1W/K1S Series
K1S220 2.48 63.0
0.50 12.7
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
UP 10 DOWN
INTERFACE ROTATION RANGE 90
DYNAMIC HEIGHT ADJUST RANGE 19.62 6.62 498.3 168.1
K1W22H 1.38 34.9
6.75 171.5
DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9
12.32 5.57 312.9 141.5
INTERFACE ROTATION RANGE 90
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
TILT RANGE 10 UP 10 DOWN
DYNAMIC HEIGHT ADJUST RANGE 21.79 8.79 553.5 223.3
5
K1W/K1S Series
Installation Instructions
K1S22H 2.01 51.1 6.75 171.5
DYNAMIC LIFT ARM LENGTH RANGE STRAIGHT ARM = MAX FULL UP/DOWN = MIN 10.21 7.12 259.3 180.9
12.32 5.57 312.9 141.5
INTERFACE ROTATION RANGE 90
MOUNTING PATTERN COMPATIBILITY 100 X 100 75 X 75
TILT RANGE 10 UP 10 DOWN
DYNAMIC HEIGHT ADJUST RANGE 21.94 8.94 557.2 227.0
0.22 5.6
HOOK BASE DISTANCE RANGE 4.06 2.56 103.2 65.1
HOOK TIP DISTANCE RANGE 3.55 2.05 90.3 52.2
6
Installation Instructions
K1W/K1S Series
LEGEND Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Einstellen
Chave de fendas Phillips
Ajustar
Cacciavite a stella
Regolare
Kruiskopschroevendraaier
Afstellen
Tournevis à pointe cruciforme
Ajuster
Open-Ended Wrench
Remove
Llave de boca
Quitar
Gabelschlüssel
Entfernen
Chave de bocas
Remover
Chiave a punte aperte
Rimuovere
Steeksleutel
Verwijderen
Clé à fourche
Retirez
By Hand
Optional
A mano
Opcional
Von Hand
Optional
Com a mão
Opcional
A mano
Opzionale
Met de hand
Optie
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Llave de seguridad
Sechskantschlüssel
Sicherheitsschlüssel
Chave de cabeça sextavada
Chave de segurança
Chiave esagonale
Chiave di sicurezza
Zeskantsleutel
Veiligheidssleutel
Clé à tête hexagonale
Clé de sécurité
7
K1W/K1S Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
7/16” 1/2”
1/8”
#2
3/16” (included) 1/8” (included) 5/32” (included with K1S120 and K1S22H only)
PARTS
A (1) [Arm assembly] (K1W120 shown)
B (4/8)* M4x10mm
D (4/8)* M10x5.3x10
C (4/8)* M4x20mm
*single display models/ dual display models
K1W models only!
F (4) 1/4 x 2 1/2”
E (1) [Wall bracket]
G (4) 1/4”
H (1) M4 x 4mm
K (1/2)* #10-32 x 3/8"
J (1) - included with K1W22H and K1S22H Models ONLY
J3 (1) 5/16-18 x 3"
J1 (1) [Array]
J2 (1) [Handle]
J4 (1) [Pivot pin]
J5 (1) J11 (1) J8 (2) [Pocket washer] J6 (1) J9 (1) J10 (1) J7 (2) 5/16-18 [Array Cable [Thin steel [Plastic [Rotational [Cable clip] spacer] clip] washer] washer]
8
J12 (1) [Pivot point spacer]
L (1) 3/16”
M (1) 1/8”
N (1) 5/32” (K1S120/22H only)
Installation Instructions
K1W/K1S Series
Assembly And Installation
3 (A) set screw
6
side view
5
4
(F) x 2
(E) (G) x 2
Figure 1
Connecting K1W Series (wall mount) to Wall 1.
Determine mounting location on wall.
2.
Use a stud finder to locate 2" x 4" wood stud.
3.
Use wall bracket (E) to mark and drill two 1/8” x 2 1/2” holes in wall at desired mounting location. (See Figure 1)
IMPORTANT ! : Only top and bottom holes of wall bracket (E) must be used to attach bracket to wall as shown in Figure 1. Do NOT use any other holes to secure bracket to wall! 4.
(arm not shown for clarity)
2
OFBLU bracket
Use two 1/4-2 1/2” hex head lag screws (F) and two 1/4” washers (G) to install wall bracket (E) onto wall. (See Figure 1)
IMPORTANT ! : Over tightening screws (F) may cause bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in Step 6. 5.
Hang monitor arm (A) over wall bracket (E). (See Figure 1)
6.
Secure monitor arm to wall bracket (E) by tightening set screw. Ensure set screw engages back side of wall bracket (E) to properly secure mount. (See Figure 1)
3
Figure 2
Connecting K1S Series to Office Furniture NOTE: K1S220 has an OFBU bracket instead of an OFBLU bracket. Proceed to K1S220 section if installing K1S220.
K1S120 and K1S22H 1.
Determine mounting location.
2.
Hang OFBLU bracket onto slat wall at desired mounting location by inserting the upper mounting plate into wall track. (See Figure 2)
3.
Let lower mounting plate rest against slat wall.
9
K1W/K1S Series 4.
Installation Instructions
Using 5/32” hex key (N), turn adjustment screw clockwise to lower mounting plate until it is able to easily slide into wall track. (See Figure 3)
5.
Using 5/32” hex key (N), turn adjustment screw counterclockwise to raise lower mounting plate until bracket is fully secured to slat wall. (See Figure 3)
(arm not shown for clarity)
2
4
OFBU bracket OFBU bracket
4
5
adjustment screw
4
3
Figure 5 5.
Tighten two upper and lower button head cap screws to secure OFBU bracket to wall. (See Figure 6)
(arm not shown for clarity)
OFBU bracket x4
Figure 3
K1S220 1.
Verify mounting brackets on OFBU bracket can move freely. (See Figure 4)
5
(arm not shown for clarity) OFBU bracket
1
5
x4
(arm not shown for clarity)
Figure 6 Figure 4 2. 3. 4.
10
Locate desired installation location and slide upper mounting plate into wall making sure bracket is seated in channel bottom. (See Figure 5) Let lower mounting plate rest against wall. Using 1/2” socket, tighten tension hex head bolt until lower mounting plate slides into channel in wall and continue tightening until resistance is felt. (See Figure 5)
IMPORTANT ! : If the display being installed has a recessed mounting surface, the display must be assembled to the mount prior to mount installation. See Display Installation in this document before proceeding.
Installation Instructions
K1W/K1S Series
Array Installation (K1W22H/K1S22H ONLY)
Display Installation
1.
Slide rotational spacer (J10) into opening on array attachment bracket. (See Figure 7)
1.
2.
Use 5/16-18 x 3" button head cap screw (J3), two thin steel washers (J8), plastic spacer (J9), pocket washer (J5), pivot pin (J4), pivot point spacer (J12) and 5/16-18 lock nut (J6) to secure array (J1) to K1 arm (A). (See Figure 7)
Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount. (See Figure 8)
1
NOTE: Cable clip (J11) can be used in place of pivot point spacer (J12) if additional cable management is desired. (See Figure 7)
2
(J3)
(J8) x 2
1
quick release lever
(J9) (J5)
Figure 8
(J1)
1 (J10) WARNING: Exceeding the weight capacity can result in (J11) or (J4) (J12)
(J6)
(A)
serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the K1W/K1S Series Monitor Arm up to (and including) the display does not exceed the weight limits listed below. Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury. MODEL
Max Weight Allowed for EACH Display
Max Weight Capacity of Mounting System
K1W110
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
25 lbs
(11.34 kg)
(11.34 kg)
25 lbs
50 lbs
(11.34 kg)
(22.68 kg)
25 lbs
50 lbs
(11.34 kg)
(22.68 kg)
9 lbs
18 lbs
(4.08 kg)
(8.16 kg)
9 lbs
18 lbs
(4.08 kg)
(8.16 kg)
K1W120
Figure 7
K1S120
K1W220
K1S220
K1W22H
K1S22H
11
K1W/K1S Series
Installation Instructions
2.
Carefully place display face down on protective surface.
3.
Connect faceplate to display For flush mounting hole installation:
•
4.
Position display with faceplate attached above mount. (See Figure 11)
5.
Slide faceplate onto mounting head until quick release tab clicks into place. (See Figure 11)
Using Phillips screwdriver, carefully install four M4x10mm screws (B) through corresponding holes on faceplate and into the mounting holes on the display. (See Figure 9)
(for flush mounting holes)
quick release faceplate
5
(B) x 4
3
Figure 11
Handle Installation (K1W22/K1S22 models only)
Figure 9 For recessed mounting hole installation:
• •
Place four spacers (D) on top of mounting holes on back of display. (See Figure 10) Using Phillips screwdriver, carefully install four M4x20mm screws (C) through corresponding holes on faceplate, spacers (D) and into the mounting holes on the display. (See Figure 10)
1.
Loosen four screws securing handle brackets to K1W22/ K1S22 array. (See Figure 12)
2.
Install uprights of handle (J2) into handle brackets located on the back of array. (See Figure 12)
1
x4
2
(for recessed mounting holes)
2 quick release faceplate
3
(C) x 4
(D) x 4
(J2)
Figure 12
Figure 10
12
Installation Instructions 3.
K1W/K1S Series
Position handle (J2) at desired height and secure by tightening button head cap screws attaching handle brackets to array. (See Figure 13)
Rotational Adjustment NOTE: (Optional) Rotational adjustment may be locked by installing rotational locking screw (K) into back of faceplate. (See Figure 15)
x4
3
(K)
3 3
Figure 15
Figure 13
Adjustments Pitch Adjustment (non-array models) 1.
Adjust pitch to desired tilt position. (See Figure 14)
2.
Adjust pitch tension screw to change the adjustment tension. (See Figure 14)
Pivot Adjustment (non-array models) 3.
Adjust pivot position as desired. (See Figure 14)
4.
Use 3/16” hex key (K) to adjust pivot point tension screws to change pivot adjustment tension. (See Figure 14)
5.
The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor. (See Figure 14)
6.
Use 3/16” hex key (K) to adjust rotational adjustment screw to adjust rotational tension. (See Figure 14)
Lift Arm Tension Adjustment 1.
Tension may also be adjusted with upper tension adjustment screw inside cable management cover and 1/8” hex key (N). (See Figure 16)
Reduce tension (lighter display) Increase tension (heavier display)
6 5
Rotational tension pivot point tension
3
Do NOT over-tension adjustment tension screw.
1
pitch tension
Figure 16 Figure 14
13
K1W/K1S Series
Installation Instructions
Adjustments - K1W22H/K1S22H models only
Display Removal
Display Adjustments 1.
Loosen knobs securing faceplates to array. (See Figure 17)
WARNING: Only remove display from mount when the
2.
Slide displays laterally on array to adjust lateral shift. (See Figure 17)
3.
Adjust pitch and pivot position as desired. (See Figure 17)
display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 19)
4.
Tighten knobs to secure faceplates in position. (See Figure 17)
1.
Make sure display is in the upright position.
2.
Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount. (See Figure 19)
3 3 2 3 2 3
quick release tab
2
1
4
Figure 17 Array Bar Roll Adjustment
Figure 19
1.
Loosen roll adjustment screws on back of array bracket. (See Figure 18)
Display Removal Security Screw
2.
Adjust roll of array bar as desired. (See Figure 18)
NOTE: In order to prevent display from being easily removed
3.
Tighten roll adjustment screws on back of array bracket. (See Figure 18)
1
from mount using the quick release lever, install M4x4mm security screw (K) into lower hole on back of faceplate. (See Figure 20)
3
(K)
2 2 Figure 20
Figure 18
14
Installation Instructions
K1W/K1S Series
Cable Management 1.
Press insides of cable management covers at both ends to unhinge tabs on either end of cable management cover on upper arm. (See Figure 21)
2.
Lift cable management cover up until tabs are unhinged and cover is in the “open” position. (See Figure 21) and (See Figure 22)
IMPORTANT ! : Be sure to leave enough slack in the cables near display and arm joint to allow for full arm articulation! 4.
Close cable management covers on monitor arm. (See Figure 22)
5.
Repeat Steps 1-4 for lower arm.
Array Models 1.
Install array cable clips (J7) to back of array. (See Figure 23)
2.
Route cables through array cable clips (J7) as desired. (See Figure 23)
3.
Route cables through arm cable clips as desired. (See Figure 23)
1 1 (J7)
2
2 3 cable management cover tabs
Figure 21
Figure 23
3
2
cable (typical)
4 3
2 4
Figure 22 3.
Route cables through cable management channels. (See Figure 22)
15
K1W/K1S Series
Installation Instructions
USA/International
Europe Chief, a products division of Milestone AV Technologies 8800-002760 Rev00 2016 Milestone AV Technologies www.milestone.com 11/16
Asia Pacific
A P F A P F A
6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477
