Transcript
４－ＷＩＲＥ ７＂ ＴＯＵＣＨ ＰＡＮＥＬ ＳＰＥＣＩＦＩＣＡＴＩＯＮ
Customer part
No.（P/N）:
KD-007
Model No.:
Structure：
ITO film + ITO glass + FPC connector
Dimension： Glass Outline Deminsion： View Area： Active Area： FPC Length ： Thickness of FPC terminal： Total thickness:
165.70*99.70±0.30mm 156.00*88.50±0.30mm 154.00*86.50±0.30mm 50.15±0.50mm 0.3±0.05mm 1.45±0.15mm
Electricity： Electrical Grade：5V(DC),1mA Light Transmission：film with glass model—550nm 78% Insulation Impedance : Analog type—25V(DC) ﹑10MΩ↑ Top Circuit Resistance：400±50Ω
2
Bottom Circuit Resistance：500±50Ω Top Circuit Loop Resistance：500Ω~950Ω. Bottom Circuit Loop resistance：150Ω~400Ω. Chattering Time：≤15ms Linearity(for Resistive type only)：≤1.5% Pen Hitting Durability：≥1000000 times（with the R3.0 silicon rubber） Pen Sliding Durability：>100000 times Mechanical： Actuation force: 10-100g Light Transmission：film with glass model—550nm 78% Surface Hardness： >3H
Heat Seal Strength: FX>2 ㎏、FY＞500g、FZ＞150g, after three directions pulling force testing the product function is ok. Testing method: With manual pulls the Ergometer separately to carry on the testing for X.Y.Z three directions, and then the function testing. Environment Condition： Operation temperature：-10℃～+60℃ Storage temperature：-20℃～+70℃
High temperature：85℃,8 小时 Constant temperature and humidity：40℃,90%/RH,24 Hr.
3
ITO ＣＯＳＭＥＴＩＣＳ STANDARDS
The following standard is only adaptable to the visual area. As long as the TP has a good function, the appearance of the non-critical area could be ignored. W=Width L=length D=Diameter GT=Glass thickness。The dirts which could be wiped up with ethyl alcohol are not concerned to the appearance standard. The anomalies are taked as lints if the length is three times than the wideth in some direction.And the extra space dots will be regarded as opaque spots,well the overwhelmed silver carbon ink is considered to the NG defeats. • Inspection condition: for all transparent soft touch switchs,use white fluorescent lighting (above 40W) test them at a 45angle,and the inspection should be done at a distance of 20cm to 30cm between eyes and the products.
•(Scratches)
Standard W<0.05mm.L≦10mm 0.05mm≦ W≦0.1mm,L≦10mm
conclusion Can be ignored. Those are ignord with more than 10mm separation
0.05mm≦ W≦0.1mm,L≦10mm L>10mm W＞0.1mm
Up to 1 is allowed with less than 10mm seperation Defective goods. Defective goods.
• ..OPAQUE SPOT(including white spots and mixed spots)
Granular sundries
standard D<0.15mm 0.15mm≦D<0.25mm
conclusion Can be disregard. Those can be ignored with more than 10mm separation 4
0.15mm≦D<0.25mm Up to 2 are allowed with less than 10mm separation Only 1 can be existed Defective goods.
0.25mm≦D<0.30mm D＞0.3mm
• Linear sundries ( such as:white line or fibre) The inspection standard and scratches the examination standard is the same. Glass fragment
Corner fragment: X<2.0mm, Y<2.0mm,andZ1,000,000 times. 3.Linearity:≤1.5%. 4.ITO Film:Sheet Resistance: 400± 50Ω; ITO Glass: Sheet Resistanc: 500± 50Ω 5.Tail Type :FPC By Plates the pure tin 6.All Tolerance Without Marked:± 0.3 1
Stiffener
99.70± 0.3 50.15± 0.5
A
B
C
D
E
F
11
