Transcript
xDSL-Multitester Performs Efficiency in Broadband Networks
®
KE3600 E N W
xDSL ADSL-ADSL2+ / VDSL2 / SHDSL (through 8-wire)* VDSL2 Vectoring (ITU-T G.993.5) xDSL Bonding (ITU-T G.998.1/2/3)* IPv4 Ping, Trace Route, etc. (IPv6 ready) Modem / Router / Terminal Mode
VDSL2 Vectoring IPv6 Ping TDR Traceroute IPTV Router ISDN IPTV Bonding Coppertest VoIP Fiber GbE
LAN connectivity via 10/100/1000 MBit/s-Ethernet Test Interface FTP Up/Download and HTTP Download up to 500 MBit/s
ISDN / POTS
ISDN BRI Uk0/S0-TE/NT and Analog (POTS) Interface
Copper Test
Line Qualification up to 30 MHz, DMM Test Functions TDR Reflectometer
High Speed Interface*
e in Mardmany Ge
Optical GbE Test Interface GPON (ONT, Modem Emulation) Second Copper GbE-Port
Software Tools*
Triple Play: VoIP and IPTV Tests Suite
*Availability on request
New Broadband Technologies The transfer of large data amounts into the cloud, the wider range of video on demand and the increasing use of IPTV and VoIP makes the availability of increasing bandwidth in data transmission absolutely necessary.
ADSL2+ ~6-25 Mb/s PON/PTB 200+ Mb/s
PC
PC VoIP
TV VoIP
In addition to the widespread ADSL technology over the copper pair, VDSL expansion is now promoted especially in urban areas for many years. VDSL provides higher bandwidth, but only over short distances. Another costly and therefore still less common solution is the GPON technology, where the fiber is not routed as VDSL2 up to cable splitters (FTTC) but directly to the customer. Service providers optimize existing VDSL connections using the new developed vectoring technology. This significantly increases the data transmission on the copper line by cancelling actively the interfering signals. Another industry standard method that helps achieving high-quality multiplay is ADSL2+ and/or VDSL2 Bonding using two copper pairs to increase available data rates. The use of new technologies, especially FTTH and VDSL2 Vectoring require a new generation of test and measurement equipment. The innovative KE3600 xDSL Multitester is capable of VDSL2 Vectoring, prepared for DSL-Bonding and GPON and as one of the only tester on the market inspection tasks are performed without restrictions in these environments.
STB
xPON
TV
VDSL2 ~50 Mb/s
ADSL2+
STB
VDSL2 BONDING ~100 Mb/s
DSL Bonding
DSLAM
CENTRAL OFFICE
PC VoIP
DSLAM
TV
FTTN
STB
VDSL2
PC
VDSL2 VECTORING ~100 Mb/s
VoIP
TV
VDSL2 VECTORING ~100 Mb/s
STB
Fiber
xDSL-Test
Copper
Ethernet-Test
KE3600 Multitester E N
At a glance
W
The KE3600 is the new, innovative and versatile xDSL Multitester for installation and troubleshooting of DSL services in ADSL1/2/2+ / VDSL2 and bundled networks and as well in FTTx deployments (GPON, Dark Fiber).
n New handheld tester with many interfaces and fast performance n Intuitive "One-Click-Operation" and clear "At-a-glance-display" n ADSL-VDSL2 and VDSL2 Vectoring (ITU-T G.993.5) in one unit n Supports Annex A/B/J/L/M with xDSL Autodetection n GbE Port for advanced Ethernet testing n Dial-in Test, Ping and Trace Route with IPv4 (IPv6 ready) n Modem, Router and Terminal Mode shows all important DSL parameters n FTP Up/Download, HTTP Download Tests up to 500 MBit/s n Large, daylight-readable color TFT with high resolution n High performance LiPo battery and expandable memory n Including software for managing and creating protocols
With a variety of interfaces the outstanding KE3600 xDSL Multitester supports many access network technologies. Accelerated fault diagnosis is made possible by its simple operation even for untrained technicians. Interferences in the network, in the outdoor and inhouse cabling but also in CPE can be narrowed down quickly. Even in FTTH networks KE3600 carries out measurements at its Ethernet or built-in SFP port. Automatic detection of the DSL Service and automated test procedures for measurements on the copper line enable fast and efficient work.The universal SFP slot for future measurement in FTTx and GPON deployments highlights the KE3600 as a perfect test solution for next generation access networks. The excellent price-performance ratio of the KE3600 xDSL Multitester makes it the perfect working tool for all inspection tasks of current and future technologies and sets standards in its class!
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
xDSL performance tester
DSL L2
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
KE3600
DSL L1
xDSL performance tester
DSL LOSS
KE3600
DSL CRC
KE3600
xDSL performance tester
KE3600 Operating Concept
"1-Click operation" "1-Click-operation" After a successful synchronization line values or graphs immediately are shown on the large color display of the KE3600 Multitester. Waiting periods or complicate and time-consuming switching between menu items and views belong to the past.With use of the function keys the "1-Click-operation" provides easy exchange between the DSL line parameters, their impact on the application layers, results of Up/Download tests, Ping and Trace Route plus VoIP and IPTV parameters. Without loss of synchronization additional settings and measurement tasks can be easily added.
"At-a-glance-display" The large display improves operating convenience significantly and allows to display measurement results at a glance. With its size of 3.5 inches and its daylight-readable color TFT the KE3600 gives the opportunity to quickly enter the required settings. For checking the configuration the user is advised by colors about missing or incorrect settings of test parameters. This greatly facilitates the operation. For the large number of graphical result displays of line and copper test applications, the high resolution screen is a big advantage.
"Management-made-easy" The supplied KE Manager software is a flexible tool to manage the KE3600, to download the measurements and to create customized measurement reports. The surface is kept simple and intuitive to use, profiles can be easily created and edited in order to transfer them on the KE3600 Multitester to accelerate productivity.
"Field-use-proofed" The robust construction with drop and screen protection along with long battery life makes the KE3600 the perfect companion for installers and service technicians.
KE3600 Options DSL LOSS
DSL L1
DSL L2
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
KE3600
DSL CRC
W
xDSL performance tester
E N
ISDN (BRI) /Analog (POTS) Interface (optional) n Functions for installation and maintenance of S0 TE/NT-, Uk0 and analog connections n Connection and self call tests n Extensive service query n Detailed information on the line status n BERT test for determining the bit error ratio
VoIP Tests n Terminal simulation / VoIP connections over xDSL and Ethernet / VoIP Signaling Protocol SIP / Call setup both with and without a registrar / proxy
KE3600 xDSL performance tester
TDR functions (optional, only in conjunction with Copper Test Option) n The integrated TDR (Reflectometer) can detect and precisely localize any changes in impedance of the twisted pair, such as short circuit, disruption and water entry. The TDR function is also suitable for the assessment of the cable and allows the detection of joints, branches or stubs (bridge taps).
KE3600
n Prequalification of the copper lines. Measures the suitability of the intended xDSL application system with tests such as Impedance, Attenuation, Balance, NEXT Measurement, Receive Level, as well as Wideband Noise and Impulse Noise Measurements. n Digital Multimeter Measurements for troubleshooting such as Voltage, Insulation, Resistance, Capacitance and Capacitive Unbalance. The Loop Analysis summarizes the key measurements and automates the user configurable measurement process. n KE900 management functions: Sends switching commands to the optional Remote Unit KE900 directly for comfortable remote switching of copper pairs at the far end of the line.
xDSL performance tester
Copper Tests up to 30 MHz(optional)
IPTV Tests n Set-Top-Box-Emulation / Review packages and switch-on and switching times
Configuration KE3600
Description xDSL performance tester
Type
0.49830
DSL CRC
DSL LOSS
DSL L1
®
F3
F2
F1
F4 SEL
ESC
ON OFF
1 4
GHI
7
3
2
DEF
ABC
5
6
JKL
MNO
8
9
PQRS
TUV
WXYZ
*
0
#
Configuration
Availability
xDSL Multitester for ADSL/ADSL2/2+ Annex A/B/L/M/J, Up/Downstream, IP Ping, Modem, Router and Terminal Mode, Software, integrated LiPo batterypack. Incl. power supply, test leads for built-in interfaces and transportation pouch.
BATT CHRG
DSL L2
KE3600
No.
VDSL2 Annex A und B with Vectoring. Profile 8a/b/c/d, 12a/b, 17a (30a only in combination with Bonding)
0.49830-12
KECT3
Copper Test Interface for DMM Testing (Digital Multimeter), xDSL Line Qualification up to 30 MHz. Integrated Remote Control Functions for Line Test Assistant KE900 Remote
0.49830-11
TDR
TDR measurements up to 6km cable length with 0,5mm ø. Adjustable pulse length, attenuation and zoom. Dead zone 3,80 m
0.49830-25
ISDN
ISDN BRI S0-TE/NT, ISDN Uk0 (4B3T or 2B1Q) and Analog (POTS) Interface incl. ear set with microphone
0.49830-6
IPTV
IPTV-Test (Set Top Box Emulation)
0.49830-5
VoIP
VoIP-Test (Terminal simulation) incl. ear set with microphone
SFP-Port
SFP Port for SFP Copper or SFP Fiber modules. Usable as second GbE-Port or GPON (ONT, modem emulation). The according SFP Transceivers are available separately.
in preparation
0.49830-7B
Bonding
DSL Bonding Module Supports profiles 8a/b/c/d, 12a/b, 17a, 30a
in preparation
0.49830-26
SHDSL
SHDSL 8-wire Interface
Not in conjunction with 0.49830-12 KECT3
in preparation
S2M
ISDN PRI S2M Primary Rate Multiplex Interface
Only in conjunction with 0.49830-26 SHDSL
in preparation
0.49820-16
Car
Car Charger 12 V 1,5 A
0.49602
Earset
Ear set including microphone with 3,5 mm phone jack
0.49620
KE901
Mode
On/Off
LS Suche EIN Suchton ändern OFF -LS Ende
1 ffre Oo n + Port 4 P t1
3
PORT 1
S e Takt 3sek Pcorhtl 1ife
4 de V ort 2 un+ Pn ortb1 Pe
5 de Ve ort 3 un+ Pn Porrtb1
On/Off
PORT 1
PORT 4
PORT 2
Software Option
Mode
PORT 3
zweite Ebene
KE900
INFO
ch So e P rtl 1ife
Shift
0.49620-10
Low Batt
2
KE910 CONTROLLER
–
PORT 4
–
PORT 3
Upgrade VDSL2
PORT 2
0.49830-10
Only in conjunction with 0.49830-12 KECT3
KE901 Remote Switch Kit KE900 Remote Line Switch and KE910 Controller for driving manual test procedures at the far end of the line KE900 Remote Electronic Line Switch for control of manual and automated test procedures via KE3600 xDSL Multitester equipped with KECT3 option
Hardware Option
Works in conjunction with 0.49830-12 KECT3
Specifications ADSL1/2/2+
ITU-T G.992.5 (ADSL2+ incl. Annex A, B, J, M) ITU-T G.992.3 (ADSL2 incl. Annex A, B, J, L) ITU-T G.992.2 (G.Lite incl. Annex A, B, J) ITU-T G.992.1 (G.DMT incl. Annex A, B, J)
ATIS/ANSI T1.413 Issue 2 IEEE 802.3ah (PTM) ITU-T G.998.1/2/3 Bonding*
VDSL2
ITU-T G.998.1/2/3 Bonding* ITU-T G.993.2 Annex A, B ITU-T G.993.5 Vectoring
Profiles: 8a/b/c/d, 12a/b, 17a, 30a Band Plan: 997, 998, US0 IEEE 802.3ah (PTM)
DSL parameters
Maximum attainable bit rates Actual achieved bit rates Actual bonded achieved rates Latency modes: fast, interleaved Data modes: ATM, PTM Capacity (%) Signal-to-noise ratio (SNR) margin Output power Attenuation Bits/bin Attenuation/bin (Hlog/bin)
QLN/bin SNR/bin Vendor code, revision Interleave depth Interleave delay INP G.INP Vectoring Modes: PTM, ATM, LOS, FEC, CRC, HEC LATN per band SATN per band
Test interfaces
VDSL2, ADSL 1/2/2+ Ethernet 10/100 MBit/s Managementport
Ethernet 10/100/1000 MBit/s Testport
Encapsulation methods
RFC 2684 supporting bridged Ethernet (IPoE) IPoA (RFC 1577)
PPPoE (RFC 2516) PPPoA/LLC and PPPoA/VC-MUX (RFC 2364)
Operating modes
DSL Terminate Modem Replacement (DSL to Ethernet) Pass Through
Ethernet Terminate Ethernet/Ethernet Pass Through
Login format
User name and password using PAP/CHAP
Connectivity support
LAN/WAN status DNS, gateway DHCP client/server, DHCP vendor class NAT
Ping test
Ping destination: Gateway, IPv4 (IPv6 ready) adress or URL Number of pings: 1 to 99 Packet size: 32 to 1200 bytes (default is 32) Timeout: 1 to 10 seconds Results: Packets sent/received, average round-trip delay (ms)
Trace Route test
Trace Route destination: Gateway, IPv4 (IPv6 ready) adress or URL Timeout: In seconds, default is 1 s, maximum is 10 s Packet size: 32 bytes Number of hops: 1 to 32 (default is 30) Results: Indicates IP address of hop and round-trip time in milliseconds (ms)
FTP/HTTP speed test
Address: IP or URL Direction: Upload and/or download Results: Time, kB transferred, speed in kbit/s Bookmarks: User-definable
Software options
IPTV Tests* VoIP Tests*
Interface options
ISDN BRI Uk0 / S0 / POTS Interface Copper Test Interface for Line Qualification with DMM (KECT3) TDR finds and localices cable faults (only with KECT3 Copper Test Interface) xDSL Bonding Interface* SHDSL 8-Wire Interface* SFP Port for Copper, Fiber (second GbE-Port) or GPON (ONT), Transceiver optional* ISDN PRI S2M Interface*
General data
Display 3,5" TFT-Display RGB 240 x 320
E N W
VLAN ID, VLAN tagging VPI/VCI IP release Signal Strength
Power Supply Size Built-in LiPo battery 23 x 11/9 x 7 cm > 4 hours in test mode 9 x 4.5/3.5 x 2.8" charging time 6 hours
Weight 850 g 1.87 lb
Housing High impact resistant ABS, w. drop protection
*more information and availability on request Your Dealer
e in Mardmany Ge
HSS Consulting 23-25 Rue Jean Jacques Rousseau 75001 Paris
KURTH ELECTRONIC GmbH Mühleweg 11 D-72800 Eningen u. A. GERMANY
®
Tel. +49(0)7121-97 55-0 Fax +49(0)7121-97 55 56
[email protected]
www.kurthelectronic.de
[email protected] Tel : 0175834576 Mob : 0668152944
07/2013 Product design and specifications subject to change without notice. All trademarks belong to their respective companies.
Compliance
