Transcript
UHF FM REPEATER
TKR-850 SERVICE MANUAL © 2001-1 PRINTED IN JAPAN B51-8557-00 (N) 1435
Knob (DC source) (K29-9106-04) Knob (VOL) (K29-5389-03)
Panel (Outer) (A62-0840-03)
Panel assy (A62-0934-03)
Key top (K29-5460-02)
Modular jack (E08-0543-05)
CONTENTS GENERAL .................................................. 2 SYSTEM SET-UP ...................................... 2 OPERATING FEATURES .......................... 3 REALIGNMENT ....................................... 11 INSTALLATION ....................................... 13 MODIFICATION ....................................... 15 DISASSEMBLY FOR REPAIR ................. 16 CIRCUIT DESCRIPTION .......................... 17 SEMICONDUCTOR DATA ...................... 23 DESCRIPTION OF COMPONENTS ........ 25 PARTS LIST ............................................. 27 EXPLODED VIEW .................................... 37 PACKING ................................................. 39 ADJUSTMENT ........................................ 40
TERMINAL FUNCTION ........................... WIRING .................................................... PC BOARD VIEWS RX PLL/VCO (X58-4800-XX) .............. TX PLL/VCO (X58-4810-XX) ............... DISPLAY UNIT (X54-3330-20) ............ FINAL UNIT (X45-3630-XX) ................ TX-RX UNIT (X57-6270-XX) (A/2) ...... TX-RX UNIT (X57-6270-XX) (B/2) ...... SCHEMATIC DIAGRAM .......................... BLOCK DIAGRAM ................................... KES-4 (EXTERNAL SPEAKER) ............... SPECIFICATIONS ....................................
47 51 53 54 55 59 65 71 77 89 92 93
TKR-850 GENERAL / SYSTEM SET-UP INTRODUCTION
PERSONNEL SAFETY
SCOPE OF THIS MANUAL This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service information for the equipment and is current as of the publication date. Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions. These are issued as required.
The following precautions are recommended for personnel safety : • DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. • SHUT OFF and DO NOT operate this equipment near electrical blasting caps or in an explosive atmosphere. • This equipment should be serviced by a qualified technician only.
ORDERING REPLACEMENT PARTS
SERVICE
When ordering replacement parts or equipment information, the full part identification number should be included. This applies to all parts : components, kits, or chassis. If the part number is not known, include the chassis or kit number of which it is a part, and a sufficient description of the required component for proper identification.
This radio is designed for easy servicing. Refer to the schematic diagrams, printed circuit board views, and alignment procedures contained in this manual.
SYSTEM SET-UP Merchandise received
Frequency range (MHz) TX/RX 450~480 TX/RX 480~512 TX/RX 440~470
Choose the type of transceiver
RF power 40W 40W 40W
Type K K2 E
See page 11. Repeater A personal computer (IBM PC or compatible), programming interface (KPG-46), programming & setup and programming software (KPG-66D) are required for programming. DC power supply or duplexer?
YES
Installation in the optional space
NO
External speaker? NO
Delivery
2
YES
KES-4 installation
TKR-850 OPERATING FEATURES 1. Controls and Functions 1
1-1. Front Panel
2
9
1 Speaker
3
8
4
7
5
6
7 Programmable Function keys
2 CH/STATUS Display Two, 7-segment digits display the channel number or status.
3 VOLUME control Rotate to adjust the volume.
4 DC source ON/OFF switch 5 DC source indicator Lights green when DC source is applied from the DC 13.6V jack (DC 13.2V jack on E type versions). Lights red when DC source is applied from the BACK UP battery terminal.
Press these keys to activate their programmable functions. PF1 key (left side)
Default : None (No function)
PF2 key
Default : Repeat disable/enable
PF3 key
Default : TX disable/enable
PF4 key
Default : Take over
PF5 key
Default : Monitor on/off
PF6 key (right side)
Default : Channel up
8 BUSY indicator Lights green while a signal is being received.
6 MIC jack
9 TX indicator
Connect a microphone to this 8-pin modular jack.
Lights red while transmitting.
1-2. Rear Panel 1
2
8
7
3
4
6
9
5
1 TX OUT jack Connect a TX antenna or a duplexer to this receptacle.
2 CONTROL I/O jack Connect an external programming device or repeater controller to this DB-25 interface.
3 FUSE Insert 15 A blade fuses into these fuse holders.
4 RX IN jack Connect a RX antenna or a duplexer to this BNC receptacle.
5 DC 13.6V (K type) / DC 13.2V (E type) jack Connect a 13.6 V (K type) or 13.2 V (E type) DC power supply to this jack.
6 BACKUP battery terminal 7 TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack.
8 Cooling fan 9 Optional space For external DC power supply, or duplexer, etc.
3
TKR-850 OPERATING FEATURES 2. Two 7-segment LED displays
• “E2” is displayed when the channel data is not written.
• Channel display (1~16) : While operating normally in user mode.
• When the displayed channel is contained in scan sequence, the right side decimal point is displayed.
• When the displayed channel is the priority channel, the left side decimal point is displayed.
• “E3” is displayed when PLL is unlocked. Receiver PLL unlocked = flashing BUSY LED. Transmitter PLL unlocked = flashing TX LED.
• “E4” is displayed when PTT is attempted on a channel number that has no frequency data programmed.
• “SC” is displayed while in scan mode. • “PC” is displayed while in PC mode.
• “PG” is displayed while in firmware programming mode. 2 decimal points displayed = 115,200bps 1 decimal point displayed = 57,600bps No decimal = 38,400bps
• “E1” is displayed when FPU data is not written.
4
TKR-850 OPERATING FEATURES 3. Programmable Functions TKR-850 contains many Programmable Functions tabled below. Programmable Function
Description
AUX Out 1~5 Off
AUX Out 1 to 5 ports become deactivated, respectively.
AUX I/O 1~6 Off
AUX I/O 1 to 6 ports become deactivated, respectively.
AUX Out 1~5 On
AUX Out 1 to 5 ports become activated, respectively.
AUX I/O 1~6 On
AUX I/O 1 to 6 ports become activated, respectively.
AUX Out 1~5 On/Off
AUX Out 1 to 5 ports are toggled between its active and inactive states, respectively.
AUX I/O 1~6 On/Off
AUX I/O 1 to 6 ports are toggled between its active and inactive states, respectively.
Channel 1~16
Directly select Channel 1 to 16, respectively.
Channel Down
The channel decrements by one.
Channel Up
The channel increments by one.
CW ID On
The CW ID is transmitted.
CW Message 1~8 On
The CW Message 1 to 8 is transmitted, respectively.
Display Off
All panel LEDs are turned off except the Power LED.
Display On
All panel LEDs become active as normal status indicators on the repeater.
Display On/Off
All panel LEDs, with the exception of the Power LED, are toggled between off and their normal status on the repeater.
Hold Time Enable
The Parameter of Repeat Hold Time is enabled.
Hold Time Disable
The Parameter of Repeat Hold Time is disabled.
Hold Time Disable/Enable
The Parameter of Repeat Hold Time is toggled between disabled and enabled.
Local Tx Disable
The local mic’s PTT is disabled.
Local Tx Enable
The local mic’s PTT is enabled.
Local Tx Disable/Enable
The local mic’s PTT is toggled between disabled and enabled.
Monitor Off
The QT/DQT decoder is disabled.
Monitor On
The QT/DQT decoder is enabled.
Monitor On/Off
The QT/DQT decoder is toggled between disabled and enabled.
Monitor Momentary
The QT/DQT decoder is momentarily disabled.
Multi Table Sub
Multi Table No. Select Signalling changes to the Multi Table Sub.
Multi Table Main
Multi Table No. Select Signalling changes to the Multi Table Main.
Multi Table Main/Sub
Multi Table No. Select Signalling changes between Multi Table Sub and Multi Table Main.
QT/DQT Dec Disable
Disables the QT/DQT decode operation.
QT/DQT Dec Enable
Enables the QT/DQT decode operation.
QT/DQT Dec Disable/Enable
Toggles between disabling and enabling the QT/DQT decode operation.
QT/DQT Enc Disable
Disables the QT/DQT encode operation.
QT/DQT Enc Enable
Enables the QT/DQT encode operation.
QT/DQT Enc Disable/Enable
Toggles between disabling and enabling the QT/DQT encode operation.
Repeat Disable
Disables repeater operation.
Repeat Enable
Enables repeater operation.
Repeat Disable/Enable
Toggles between disabling and enabling repeater operation.
Reset
Resets to default condition set up by FPU.
DC Power Save Off
Activates DC Power Save Mode Off.
DC Power Save On
Activates DC Power Save Mode On.
DC Power Save On/Off
Toggles between DC Power Save Mode On and Off.
5
TKR-850 OPERATING FEATURES Programmable Function
Description
Scan Off
Inhibits scanning.
Scan On
Starts scanning.
Scan On/Off
Scanning is toggled between being enabled or inhibited.
Scrambler Off
Disables an installed optional voice scrambler board.
Scrambler On
Enables an installed optional voice scrambler board.
Scrambler On/Off
Toggles between enabling and disabling an installed optional voice scrambler board.
Squelch Off
The Squelch unmutes.
Squelch On
The Squelch mutes.
Squelch On/Off
The receiver’s squelch toggles between muted and unmuted.
Squelch Momentary
The Squelch momentarily unmutes.
Take Over On/Off
Toggles between disabling and enabling remote wireline control.
Test Tone Off
The Test Tone is inhibited.
Test Tone On
The Test Tone is enabled.
Test Tone On/Off
Toggles between enabling and inhibiting the Test Tone.
TOT Disable
The Time Out Timer is disabled.
TOT Enable
The Time Out Timer is enabled.
TOT Disable/Enable
The Time Out Timer is toggled between disabled and enabled.
TX Disable
The transmitter is inhibited.
TX Enable
The transmitter is enabled (normal).
TX Disable/Enable
Toggles between transmitter inhibited and transmitter enabled (normal).
The following Programmable Functions are output functions used to tell the condition of the TKR-850 to an external device. The output functions can be assigned to only AUX Outputs as follows. Programmable Function COR (Carrier Operate Relay)
Description This function becomes valid if an RF carrier is present.
TOR (Tone Operate Relay)
This function becomes valid if an RF carrier and the specified QT/DQT are present.
RX Unlock
This alarm function becomes valid if the RX PLL circuitry becomes unlocked.
TX Unlock
This alarm function becomes valid if the TX PLL circuitry become unlocked.
Power Supply Lower Limit
This alarm function becomes valid if the DC power supply voltage becomes less than the preset point. The preset point is selected in the range of 10.6V to 13.6V.
TXS (TX Sense)
This function becomes valid when the transmitter is keyed.
Selectable
AUX Outputs which are set up as Selectable appear in the available Function List for the AUX Input Functions and Key Assignment. This allows AUX Inputs and PF Keys to be used to control AUX Outputs.
RX Signal Detect
This function becomes valid if the RX signal level becomes less than the preset point. The preset point is selected in the range of –120dBm to –95dBm.
RF Power Down Detect Fan Status
This alarm function becomes valid if the RF Power becomes less than about 10W. This alarm function becomes valid when the Fan is turned on, either by sensing a high temperature condition or by its operating mode being set to Continuous.
6
TKR-850 OPERATING FEATURES 4. Trigger Assignment The Programmable Functions described above can be assigned to PF keys, AUX input, Save on/off, Start up, and Power supply according to following table. In the last column of the table, when the Programmable Functions is assigned to any PF keys, it expresses that the LED in the PF key turns on either conditions. “Yes” expresses that the trigger is available the Programmable Function. “No” expresses that the trigger is not availabale the Programmable Function. Trigger
PF keys
Function
AUX
Save
input
on/off
Start up
Power
Condition of LED in he PF key on
supply
AUX Out 1~5 (I/O 1~6) Off
No
Yes
Yes
Yes
Yes
–
AUX Out 1~5 (I/O 1~6) On
No
Yes
Yes
Yes
Yes
–
AUX Out 1~5 (I/O 1~6) On/Off
Yes
Yes
No
No
No
Turns on in ON status.
Channel 1~16, Up/Down
Yes
Yes
Yes
Yes
Yes
Do not turn on.
CW ID On
Yes
Yes
Yes
Yes
Yes
Turns on while transmitting.
CW Message 1~8 On
Yes
Yes
Yes
Yes
Yes
Turns on while transmitting.
Display Off
No
Yes
Yes
Yes
Yes
–
Display On
No
Yes
Yes
Yes
Yes
–
Display On/Off
Yes
Yes
No
No
No
Turns on in ON status.
Hold Time Enable
No
Yes
Yes
Yes
Yes
–
Hold Time Disable
No
Yes
Yes
Yes
Yes
–
Hold Time Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
Local Tx Disable
No
Yes
Yes
Yes
Yes
–
Local Tx Enable
No
Yes
Yes
Yes
Yes
–
Local Tx Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
Monitor Off
No
Yes
Yes
Yes
Yes
–
Monitor On
No
Yes
Yes
Yes
Yes
–
Monitor On/Off
Yes
Yes
No
No
No
Turns on in ON status.
Monitor Momentary
Yes
No
No
No
No
Turns on in ON status.
Multi Table Sub
No
Yes
Yes
Yes
Yes
–
Multi Table Main
No
Yes
Yes
Yes
Yes
–
Multi Table Main/Sub
Yes
Yes
No
No
No
Turns on in Sub status.
QT/DQT Dec Disable
No
Yes
Yes
Yes
Yes
–
QT/DQT Dec Enable
No
Yes
Yes
Yes
Yes
–
QT/DQT Dec Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
QT/DQT Enc Disable
No
Yes
Yes
Yes
Yes
–
QT/DQT Enc Enable
No
Yes
Yes
Yes
Yes
–
QT/DQT Enc Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
Repeat Disable
No
Yes
Yes
Yes
Yes
–
Repeat Enable
No
Yes
Yes
Yes
Yes
–
Repeat Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
Reset
Yes
Yes
No
No
No
Do not turn on.
DC Power Save Off
No
Yes
No
Yes
Yes
–
DC Power Save On
No
Yes
No
Yes
Yes
–
DC Power Save On/Off
Yes
Yes
No
No
No
Do not turn on.
Scan Off
No
Yes
Yes
Yes
Yes
–
7
TKR-850 OPERATING FEATURES Trigger
PF keys
Function
AUX
Save
input
on/off Yes
Scan On
No
Yes
Scan On/Off
Yes
Yes
No
Scrambler Off
No
Yes
Yes
Scrambler On
No
Yes
Yes
Scrambler On/Off
Yes
Yes
No
Power
Condition of LED in he PF key on
supply Yes
Yes
–
No
No
Turns on in ON status.
Yes
Yes
–
Yes
Yes
–
No
No
Turns on in ON status.
Squelch Off
No
Yes
Yes
Yes
Yes
–
Squelch On
No
Yes
Yes
Yes
Yes
–
Squelch On/Off
Yes
Yes
No
No
No
Turns on in OFF status.
Squelch Momentary
Yes
No
No
No
No
Turns on in OFF status.
Take Over On/Off
Yes
No
No
No
No
Turns on in ON status.
Test Tone Off
No
Yes
Yes
Yes
Yes
–
Test Tone On
No
Yes
Yes
Yes
Yes
–
Test Tone On/Off
Yes
Yes
No
No
No
Turns on in ON status.
TOT Disable
No
Yes
Yes
Yes
Yes
–
TOT Enable
No
Yes
Yes
Yes
Yes
–
TOT Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
TX Disable
No
Yes
Yes
Yes
Yes
–
TX Enable
No
Yes
Yes
Yes
Yes
–
TX Disable/Enable
Yes
Yes
No
No
No
Turns on in Disable status.
None
Yes
Yes
Yes
Yes
Yes
Do not turn on.
5. Simplex/Duplex Operation The Simplex/Duplex function is used to specify whether the channel is used as simplex (receiver muted during transmit) or duplex (receiver unmuted during transmit). If the channel has same TX/RX frequency, it can operate only in Simplex mode.
6. Repeater/Base Station Operation The Repeat function is used to specify whether the channel is used as a repeater or as a base station. A repeater simultaneously and automatically re-transmits its received audio, a duplex base station has independent simultaneous transmit and receive paths, a simplex base station are mutually exclusive transmit and receive paths.
7. Signalling Feature
8
Start up
The Multi Table function enables the TKR-850 to decode any one of the 16 QT/DQTs pre-programmed into the Multi Table. When receiving a signal (repeater operation), the repeater uses the QT/DQT encode which corresponds to the decoded QT/DQT as set in the Multi Table. In the Multi Table, signalling pair of “No.1” (first column) is defined as “Primary”. A receiving signalling (if it is contained within No.1 to No.16) is defined “Current”. From No.2 to No.16, signalling pairs that can be changed between “Main Table” and “Sub Table” using AUX I/O Ports 1-4 are assigned as “Multi Table Select” and the Multi Table Main, the Multi Table Sub or the Multi Table Main/Sub function is executed. When AUX I/O Ports 1~4 are set for “Multi Table Select”, these are 4 bit Binary Coded Decimal (BCD) inputs .AUX I/O 1 is a least significant bit (LSB), and “1101” input (LSB on the right side) signifies the Table No.2 and “1100” input signifies the Table No.3.
7-1. Multiple QT/DQT
7-2. Encode Tone in Multiple
The TKR-850 can function as a multiple-QT/DQT decode/ encode unit for operation as a community repeater or multiple-QT/DQT base station. Two Multi Tables, called Main and Sub, can be created, each consisting of 16 decode/encode combinations.
When Local Microphone PTT or External PTT is active while the repeater is in use or the duplex-base station is receiving, the encode signalling is determined according to Encode Tone in Multiple function. The simplex-base station always transmits the “Primary” encode QT/DQT.
TKR-850 OPERATING FEATURES Current : When any PTT as described above is active while the repeater is in use or the duplex-base station is receiving, the “paired” encode QT/DQT associated with receiving QT/DQT is transmitted. When any PTT is active while the repeater or the duplex-base station is in idle period, the “Primary” encode QT/DQT is transmitted. Primary : When any PTT (provided that the Priority of any PTT is higher than the Priority of Repeat PTT) is active while the repeater is in use, the encode QT/DQT changes “paired” encode QT/DQT to “Primary” while continuing to transmit. When any PTT is active while the repeater is in idle period, the “Primary” encode QT/DQT is transmitted. In the base station, the “Primary” encode QT/DQT is always transmitted regardless of the receiver status.
7-3. QT Reverse Burst Time During repeat with QT tones, the repeater re-transmits a phase-shifted burst of the QT tone (“reverse burst”) when it detects the radio using the repeater has un-keyed and also sent a reverse QT burst (squelch-tail elimination). This mutes a receiving radio’s speaker audio before its receiver circuit shuts off causing squelch tail noise in the speaker audio. The TKR-850 can select the time between 140 to 200 ms that the QT reverse burst is sent. Typically this time should not have to be adjusted from the default value. The transmission of the QT reverse burst can be also inhibited if the QT Reverse Burst function is set to “No”.
7-4. DQT Turn Off Code Time During repeat with DQT tones, the repeater re-transmits a specific turn-off code when it detects the radio using the repeater has un-keyed and also sent the turn-off code (squelch-tail elimination). This mutes a receiving radio’s speaker audio before its receiver circuit shuts off causing squelch tail noise in the speaker audio. The TKR-850 can select the time between 140 to 200ms that the DQT turn-off code is sent. Typically this time should not have to be adjusted from the default value.
7-5. Off Hook Decode The TKR-850 is able to decode QT/DQT regardless whether the local microphone is in the on- or off-hook condition. When the Off Hook Decode function is enabled, the TKR-850 is capable of QT/DQT decode even though the microphone is in the off-hook condition (or a local microphone is not installed).
8. Scan Feature 8-1. Scan Operation Providing that the TKR-850 contains two or more non-priority ADD channel or one or more non-priority ADD channel and Priority channel, it starts scanning once the Scan On function is executed and displays “SC” on the 7-seg LED. Scanning stops temporarily if any following conditions be come valid.
1) if a RF carrier and a valid QT/DQT is present. The receiving channel number is displayed and the received audio is heard from a speaker. 2) if a RF carrier is present, providing that the Monitor On function is executed. 3) if the Squelch Off function is executed. Scanning stops on the channel being scanned when Squelch Off is executed, the channel number is displayed and the received audio is heard from a speaker. 4) if a local microphone’s hook is in off hook status, providing that the Off Hook Scan function is set to Disable. Scanning stops on the Revert channel, but the audio is not heard until a valid signal is received. When the received call is ended, scanning automatically resumes after the period set in Dropout Delay Time function has expired. When the Scan Off function is executed, the TKR-850 inhibits scanning and displays the selected channel.
8-2. Scan Sequence 1) Normal Scan : When no Priority channel is set, scanning of ADD channels is done in ascending order. 2) Single Priority Scan : The Priority channel is set as either a fixed channel or a selected channel. When Priority channel is set, Priority channel and non Priority channel are scanned by turns. When scanning stops on the non Priority channel, calls from the Priority channel are still checked at set intervals while scanning is stopped. This operation is called Look Back and the interval period is selected by the Look Back Time function.
8-3. Revert Channel The Revert channel is a channel that is used to transmit during scanning. The time from the end of transmission on Revert channel to the time scanning automatically resumes is set in Dwell Time function. The Revert channel types are Last Called, Last Used, Selected, Selected + TalkBack, Priority, and Priority + TalkBack. 1) Last Called : The TKR-850 reverts to the channel upon which a call was last received even if scanning has resumed (power on default = selected channel). 2) Last Used (with TalkBack) : The TKR-850 reverts to the channel that was last transmitted on (power on default = selected channel). However, if a call is received on a channel other than the last transmit channel and PTT is pressed before scanning resumes, the transceiver “talks back” on the current receive channel. 3) Selected : The transceiver reverts to the channel set by the function prior to scan initiation. 4) Selected+TalkBack : The TKR-850 reverts to the channel set by the Channel ‘X’ functions or Channel Select function prior to scan initiation. However, if a call is received on a channel other than the selected channel and PTT is pressed before scanning resumes, the transceiver “talks back” on the current receive channel. 5) Priority : The TKR-850 always reverts to the Priority channel.
9
TKR-850 OPERATING FEATURES 6) Priority+TalkBack : The TKR-850 always reverts to the Priority channel. However, if a call is received on a channel other than the Priority channel and PTT is pressed before scanning resumes, the transceiver “talks back” on the current receive channel.
9. CW ID and Message The TKR-850 contains internal automatic station identifiers. The CW ID (Morse code) is set and transmitted on a per-channel basis. The CW ID is transmitted when the interval period is reached (TX Interval Time function), the channel is changed (CW ID on Channel Change function) or CW ID Onfunction is executed. When CW ID is activated by any functions described above, it is actually sent after the total time of TX Delay Time (not applied to CW ID On function) and CW Modulation Delay Time has expired. TX Delay Time is a period from CW ID is activated to the transmitter is keyed. CW Modulation Delay is a period from the transmitter is keyed to the CW ID tone is sent. The CW ID tone is routed to the Receive Audio (RA) port and a speaker if the Send CW ID to RA function is set to Yes. The TKR-850 contains 8 message banks for CW Message. CW Message 1 to 8 is transmitted on the current channel when the CW Message 1 to 8 On function is activated, respectively.
10. PTT Priority A number of keying sources can be used to cause the TKR-850 to transmit. The transmit audio path is switched according to their keying sources and when PTTs is simultaneously activated, the transmit audio path related to the PTT with higher priority is given priority. These are Local Microphone PTT, External PTT, and Repeat PTT.
11. Time Out Timer The Time Out Timer function determines the period of time users can continuously transmit. When the selected period expires, the transmission is inhibited.
12. Repeat Hold Time The Repeat Hold Time (hang timer) function is used to prevent the repeater from being repeatedly keyed and unkeyed in response to short message traffic. When a mobile transceiver unkeys, the repeater’s Hold Timer allows the repeater to continue transmitting for a brief period while waiting for a responding end user. If no valid QT/DQT is detected within the Hold Timer period, the transmitter is allowed to unkey. This function determines the period of time that the transmitter is allowed to remain keyed after the loss of a valid QT/DQT received signal.
10
13. Take Over The Take Over function is used to disable the external wireline control of the repeater. When Take over function is enabled, the external AUX inputs and Outputs, transmit audio inputs and receive audio outputs, External PTT and External Monitor lines are disabled. All AUX Input functions assigned to any AUX Input stay in their current state. However External PTT and External Monitor switch to the “Off” state.
14. Test Tone The Test Tone is a single-frequency audio sine wave and is turned On and Off by toggling Test Tone On/Off functions. The transmitter can be modulated without a local microphone by using the test tone. When Test Tone On function is executed and any PTT is activated, the TKR-850 transmits the test tone with mic mute and also routes the test tone to RA port.
15. RF Power The TKR-850 is able to switch transmission output on a per-channel basis. When the TX High Power function is enabled, the transmission output is set to high power.
16. Fan Action The TKR-850 has a cooling fan. The Fan Action function determines whether the fan is continuously operated or operates in response to high temperatures only.
17. AUX Input and Output There are 6 programmable AUX I/O Ports 1~6 (pins 20~25) and 3 programmable AUX Input Ports 1~3 (pins 4~6) on the rear 25 pin D-Sub connector (CONTROL I/O) and 5 programmable AUX Output Ports 1~5 (pins 10, 11, 13~15) on the rear 15 pin TEST/SPKR connector. The 6 programmable AUX I/O pins are primarily intended for remote control interfaces. Each AUX I/O Port can be set for AUX Input, AUX Output, remote Channel Select or Multi Table Select types. The AUX Input Port can be set execute a single input function or a set of up to three functions when the port is activated. If the port type for an AUX I/O Ports 1~6 is set for “AUX Input”, it will also appear AUX Input window for function programming. The input logic is fixed as active Low. The AUX Output Port can be set execute a single output function. If the port type for an AUX I/O Ports 1~6 is set for “AUX Output”, it will also appear AUX Output window for function programming. The output logic of AUX Output can be set as either active High or active Low by the Logic Type function. Active High outputs a High (5V) when the programmed condition becomes valid, active Low outputs a Low (0V) when the condition becomes valid.
TKR-850 OPERATING FEATURES / REALIGNMENT 18. Channel Select AUX I/O Ports 1~4 (1 or all 4) can each be set for “Channel Select” providing up to 16 channel selection capability. These are 1 to 4 bit Binary Coded Decimal (BCD) inputs. AUX I/O 1 is a least significant bit (LSB). When all of AUX I/ O Ports 1~4 set to Channel Select, “1110” input (LSB on the right side) signifies the Channel 1 and “1101” input signifies the Channel 2.When the Channel Select function is set to any AUX I/O ports, the Channel ‘X’ function (Channel Up, Channel Down, Channel 1, etc.)can not be set to the AUX Input ports, but can be set to the PF Keys. Normally the channel control is controlled by the Channel Select function. If the Take Over function is executed, the channel control is disabled to be controlled by the Channel Select and enabled to be controlled by the PF Keys.
19. DC Power Save The TKR-850 has the DC Power Save feature. The DC Power Save Mode is activated when the DC Power Save On function is executed. When the DC Power Save Mode is activated, all panel LEDs except the Power LED are turned off, and the audio amplifier and the DSP becomes inactive. When the Display On function is executed while the repeater is in the DC Power Save Mode, all panel LEDs become active as normal status indicators on the repeater, and the audio amplifier and the DSP becomes active. However, when the Save Delay Timer A period expires, all panel LEDs except the Power LED are turned off and the audio amplifier becomes inactive again, and when the Save Delay Timer B period expires, the DSP becomes inactive. When the DC Power Save Mode is turned on or off, up to 3 functions preprogrammed into the Save On function or Save Off function are executed in sequence.
20. Power Supply The TKR-850 is able to use two Power sources that are called Main and Backup. When the Power source changes from Main to Backup or from Backup to Main, up to 3 functions pre-programmed into the Backup Power function or the Main Power function are executed in sequence.
21. Start Up When the TKR-850 is first turned on or is reset, up to 3 functions pre-programmed into the Start Up function are executed in sequence.
22. Optional Board An optional scrambler board can be installed in the TKR850. Scrambler codes between 1 and 16 are available per channel. If the scrambler board is not to be used (although it is installed), set the parameter to “Off”. When any Scrambler code is set up and the Scrambler On function is executed, the scrambler board is activated.
REALIGNMENT 1. Modes User mode PC mode
PC programming mode PC test mode
PC tuning mode
Firmware Programming mode
Mode
Function
User mode
Use this mode for normal operation.
PC mode
Use this mode to make various settings by means of the FPU through the RS-232C port.
PC programming
Use to read and write frequency data and
mode
other features to and from the repeater.
PC test mode
Use to check the repeater using the PC. This feature is included in the FPU.
Firmware pro-
Use when changing the firmware program
gramming mode
of the flash memory.
2. How to Enter Each Mode Mode
Operation
User mode
Power on.
PC mode
Received commands from PC.
Firmware Pro-
[PF1] key + Power on (one second).
gramming mode
3. PC Mode 3-1. Preface The TKR-850 repeater is programmed by using a personal computer, programming interface and KPG-66D software.
3-2. Connection Procedure 1. Connect the TKR-850 to the personal computer with the interface cable. 2. When power is applied, the user mode is entered immediately. When the PC sends a command, the repeater enters the PC mode and displays “PC” on the 7-segment LED. When data is being transmitted to the PC from the repeater, the TX LED flashes. The BUSY LED flashes when data from the PC is being received by the repeater.
Note : • The data stored in the personal computer must match the model type, when it is written into the flash memory. • Change the TKR-850 to PC mode, then attach the interface cable.
11
TKR-850 REALIGNMENT 3-3. KPG-46 Description (PC Programming Interface Cable : Option) The KPG-46 is required to interface the TKR-850 to the computer. It has a circuit in its D-sub connector (25-pin) case that converts the RS-232C logic level to the TTL level. The KPG-46 connects the microphone connector of the TKR-850 to the computer’s RS-232C serial port.
3-4. Programming Software Description The KPG-66D programming disk is supplied in 3-1/2" disk format. The software on the disk allows a user to program TKR-850 repeater via the programming interface cable (KPG46).
3-5. Programming With IBM PC Data can be programmed into the flash memory in RS232C format via the microphone connector. IBM PC
KPG-46
KPG-66D
TKR-850
Fig. 1
4. Firmware Programming Mode 4-1. Preface The TKR-850 uses flash memory to allow it to be easily upgraded when new features are released in the future.
4-2. Connection Procedure Connect the TKR-850 to the personal computer (IBM PC or compatible) with the interface cable (KPG-46). (Connection is the same as in the PC mode.)
Notes : You can only program firmware from the 8-pin microphone connector on the front panel. Using the 25-pin logic interface on the rear panel will not work.
4-3. Programming 1. Start up the programming software (Fpro. exe). 2. Set the communications speed (normally, 115200 bps) and communications port in the configuration item. 3. Set the firmware to be updated by file name item. 4. Turn the TKR-850 power on with the [PF1] key held down. Hold the key down for one second until the 7segment display changes to “P.G.”. When “P.G.” appears, release your finger from the key. 5. Check the connection between the TKR-850 and the personal computer, and make sure that the TKR-850 is in the program mode. 6. Press write button in the window. A window opens on the display to indicate progress of writing. 7. If writing ends successfully, the TX LED on the TKR-850 lights. 8. If you want to continue programming other TKR-850s, repeat steps 3 to 6.
Notes : This mode cannot entered if the firmware program mode is set to disable in the programming software (KPG-66D).
4-4. Function If you press the [PF1] key (front panel), both decimal point on the 7-segment display will disappear. The writing speed is 38400 bps (low-speed mode). If you press the [PF1] key again, the right hand decimal points will light. The writing speed is 57600 bps (middle-speed mode).
Note : Normally, write in the high-speed mode (115200 bps).
12
TKR-850 INSTALLATION
R742
R653
1
CN604
CN606
CN601
This unit has two external power supply connectors : Main DC and Backup. If an external DC power supply is connected to the main DC connector and a backup battery is connected to the Backup connector at the same time, the DC power supply switches to the battery automatically if power failure occurs. Therefore, the operation of the repeater can be continued. If the battery is used, but both the battery and power supply need not be connected (if an external switch is used or if only a solar battery is used), connect it to the Backup connector, not the Main DC connector. Current consumption can be reduced by approx. 120mA because the relay is not used. If it is installed when the temperature at the repeater site is below freezing, check whether the switch (relay) works properly after installation.
TX-RX unit (B/2) control section Component side
CN605
14
1. External Power Supply Connection (Rear Connectors) : See Page 3
2. Voice Scrambler It operates only during base operation. The voice is not scrambled when it is repeated.
2-1. Modification 1) Remove R742 and R653 on the TX-RX unit (B/2) : control section.
2-2. Connection 1) The functions of pins of CN601 on the TX-RX unit (B/2) : control section are shown in the figure. 2) Join the CN601 connector to the voice scrambler board via the E37-0808-05 connector cable. When the operation is checked in PC test mode after the modification, and the maximum deviation is adjusted, the voice from the local microphone is not modulated. In this case, remove the CN601 12-pin (PTO) cable and connect it to the land of the display unit (X54-333) from the voice scrambler. The voice from the local microphone can be modulated in PC test mode.
Fig. 1 CN601 1 TXI (MIC signal input) TXO (MIC signal output) RXI (RX audio signal input) AC (Audio control signal output) BC1 (Scramble code output 1) BC2 (Scramble code output 2) BC3 (Scramble code output 3) BC4 (Scramble code output 4) PTI (PTT signal input) CLRC (Clear code for scrambler) DEO (Detection signal output) PTO (PTT signal output) 5C (5V output) GND 14
Voice scrambler
Display unit
Fig. 2
Display unit Foil side
PTO
Fig. 3
13
TKR-850 INSTALLATION 3. External Speaker (KES-4) The TKR-850 has a internal built-in speaker (5W/8Ω), and the external speaker output from the TEST/SPKR connector (15-pin) on the rear of the radio is 4W/4Ω. Use external speaker KES-4.
3-1. Connection for the KES-4 With the TKR-850 ■ When taking the AF output from the TEST/ SPKR connector (15-pin) on the rear of the radio
Fig. 4-1
The following tools are required for changing the connector.
• Extracting tool The following extracting tool is recommended : Molex Inc. Order No. : 11-03-0002 1. Remove the connector with jumper from the external speaker connector on the rear panel of the radio. (Fig. 41) Note : Save the jumper, which is required when the radio is used without the external speaker. 2. Remove the terminals with the jumper from the connector housing holes number 9 and 12 using the extracting tool.
Removing the jumper lead (Fig. 4-2) 1) Insert the extracting tool (11-03-0002) into the connector while pushing the jumper lead in the direction of (a). 2) Push the extracting tool into collapse the barbs of the crimp terminal. 3) Pull out the lead while continuing to push the extracting tool in the direction (b). 3. Reinsert the terminal with the black and white stripe lead into hole number 12, and the terminal with the black lead into hole number 6. (Fig. 4-3) 4. Attach the connector to the external speaker connector on the radio.
Fig. 4-2
Note : Relationship between TEST/SPKR connector (15-pin) connection and speaker output. When pins 9 and 12 are shorted : Built-in internal speaker is used. When pins 9 and 12 are open and output is from pins 6 and 12 : KES-4 is used.
14
Fig. 4-3
TKR-850 MODIFICATION 1. Modification for Sinking the Collector Current Up
2. DC Source Switch
Auxiliary output 1 and 2 can each be modified to sink up 600mA of the collector current. The following modification should be installed when Auxiliary output 1 or 2 is used to control external equipment. 1. Remove D625, R755, and R769 for Auxiliary output 1 (D624, R756, and R770 for Auxiliary output 2) on the component side of the control section for TX-RX unit PCB. 2. Install $Q608, $Q612, and $R761 for Auxiliary output 1 ($Q607, $Q611, and $R759 for Auxiliary output 2) on the component side of the control section for TX-RX unit PCB. $Q607, $Q608, $Q611, $Q612 : DTD114EKA $R759, $R761 : 3.9kΩ (RK73GB1J392J) chip resistor. 3. Change R801 for Auxiliary output 1 (R797 for Auxiliary output 2) from 1kΩ (RK73GB1J102J) to 0Ω (R92-125205).
To prevent the power supply from turning off due to misoperation of the DC source switch on the front panel or accidents (tampering) after installation, the main unit can be kept on regardless of the on/off of the DC source switch on the front panel. Short the PSW land near K1 relay by soldering.
TX-RX unit (A/2) Component side
By making this modification, Auxiliary output 1 and 2 can now sink up to 600mA each.
TX-RX unit (B/2) Component side
CF1 WIDE
CF2 NARROW
PSW
K1
IC602
R756 $Q607
IC623
$R759 R755
Fig. 3
R770 $Q611
CN605
$R769 R769 C681
$Q608 $Q612
Fig. 1 5V
5V
Add $R761 ($R759) 3.9kΩ Remove D625 (D624) DA204U
Shift register IC623
Add $Q608 ($Q607) DTD114EKA Remove R755 (R756) 0Ω
Add $Q612 ($Q611) DTD114EKA Remove R769 (R770) 0Ω
Fig. 2
TEST/ SPKR
15
TKR-850 MODIFICATION / DISASSEMBLY FOR REPAIR 3. Trickle Charge for Backup Battery If the external DC power supply is connected to the Main DC connector and a backup battery (12V rechargeable type) is connected to the Backup connector at the same time, the battery can be trickle-charged from the external DC power supply with a maximum current of 0.5A. Short the CHARGE land near R61.
Notes : 1. Make this modification after removing the DC power supply and battery for safety. 2. When the DC power supply is connected after the modification, DC voltage is output to the Backup connector. Be careful during setup. 3. When the backup battery is used for a long time, remove the battery from the repeater and recharge it because the trickle charge is not sufficient for recharging a completely discharged battery.
Final Unit (A/2) Component side
CN7 BACKUP (ORANGE) K1
R61
CHARGE
Fig. 4
16
DISASSEMBLY FOR REPAIR How to Remove the Panel Assy (ABS) Note : You can remove the panel assembly (ABS) without removing the top panel (A62-0840-03). 1. To remove panel (TX-RX, 2 ), loose 6 screws ( 1 ). 2. To remove panel assembly (Front, 4 ), loose 6 screws ( 3 ). 3. The panel assembly (ABS) is security fastened by 4 tabs ( 5 ) on top and bottom. You can remove the panel assembly by pulling to front while you are pulling up the tabs.
TKR-850 CIRCUIT DESCRIPTION The BPF L4/L5 attenuates the unwanted signals, and sends only the necessary signal to the first mixer DBM A1.
1. Outline The TKR-850 is a UHF/FM repeater designed to operate in the frequency range of 440 to 512MHz. The unit consists of receiver, transmitter, phase-locked loop (PLL) frequency synthesizer, and control circuits.
2-2. First Mixer The signal from the BPF is heterodyned with the first local oscillator signal from the PLL frequency synthesizer circuit at the first mixer DBM (A1) to become a 44.85MHz first intermediate frequency (IF) signal. The first IF signal is fed through two monolithic crystal filters (XF2; Wide, XF1; Narrow) to further remove spurious signals.
2. Receiver Circuit The receiver is double conversion super-heterodyne, designed to operate in the frequency range of 440MHz to 470MHz (E), 450MHz to 480MHz (K) or 480MHz to 512MHz (K2). The receiver circuit located in TX-RX unit (X57-627 A/2) consists of the following : 2-1 front-end circuit, 2-2 first mixer, 2-3 IF amplifier circuit, 2-4 audio amplifier circuit, and 2-5 squelch circuit.
2-3. IF Amplifier The first IF signal is amplified by Q2 and Q3, and then enters IC9 (FM system IC). The signal is heterodyned again with a second local oscillator signal (44.395MHz) with in IC9 to become a 455kHz second IF signal. The second IF signal is fed through a 455kHz ceramic filter, CF1 (Wide), CF2 (Narrow) to further eliminate unwanted signal, and the quadrature detection circuit FM-detects the signal to produce a base-band signal and output it from pin 11.
2-1. Front-end Circuit The front-end circuit consists of BPF L2, RF amplifier Q1, and BPF L4/L5. The helical BPF covers frequency ranges 440 to 480MHz (K,E) and 480 to 512MHz (K2), with a passband of 5.0MHz
RX ANT
TX-RX unit (X57 A/2): TX-RX MCF (Wide) XF2
IF AMP Q3
D2 SW
D1 MCF (Narrow) XF1
W/N
DET
44.850MHz
RF AMP Q1
BPF L2
RX VCO IF AMP IF AMP IF AMP A3 (X58-480) LPF Q10 Q9 Q8 VCO A
W/N
VCO B QUD
SW
fRX–44.85MHz
CF1 (Wide)
W/N SW D4
NOISE DET D5 SQL
BPF L4,L5
1st MIX DBM A1
SW
FM SYSTEM IC IC9
RSSI Q4
44.85MHz IF AMP Q2
DET
X1 44.395MHz
SW D3
CF2 (Narrow) NOISE AMP Q7
455kHz
W/N
TX-RX unit (X57 B/2): Control AMP DEI DEO IC608 AINR RD
IC614 CODEC
LPF AMP IC619 (B/2) IC619 (A/2) RXI RXO
IC622
Q606
IC629
DAC
SW
MUTE
AF AMP
AOUTR
IC604
RA
CPU
AM SPM
ASQ
IC615
IC621
INV Q605
RSSI
Fig. 1 Receiver circuit
INT SP
17
TKR-850 CIRCUIT DESCRIPTION 2-4. Audio Amplifier The audio amplifier circuit is located in control section of TX-RX unit (X57-627 B/2). The recovered audio signal obtained from IC9 is amplified by IC608, input to the AINR terminal of CODEC IC (IC614), and audio processed by DSP (IC618). The processed audio signal from AOUTR terminal of IC614 is amplified by IC619 (B/2) to a sufficient level, antialiasing filtered by IC619 (A/2). The audio signal goes to an electronic volume (IC615) V3/V4, to the input of multiplexer IC (IC622), and is amplified to drive a loudspeaker by an audio power amplifier (IC629). The 4W audio output can be provided to external 4 ohms speaker through the 15-pin test connector “SPO, SPG” on the rear panel.
2-5. Squelch Circuit The output signal from IC9 enters FM IC again, then passed through a band-pass filter. The noise component output from IC9 is amplified by Q7 and rectified by D5 to produce a DC Voltage corresponding to the noise level. The DC voltage is sent to the analog port of the CPU (IC604). IC9 outputs a DC voltage (RSSI) corresponding to the input of the IF amplifier.
3. Transmitter Circuit The transmitter circuit consists of the following circuits : 3-1 microphone circuit, 3-2 modulation level adjustment circuit, 3-3 driver and final power amplifier circuit, and 3-4 automatic power control circuit.
3-1. Microphone Circuit The signal from the microphone is passed through AGC circuit located in display unit (X54-333), so that it does not saturate. This circuit consists of IC501, D501, D502, Q501, and Q502. The AGC is operated by controlling the + and – side levels of amplitude using the current obtained by positive and negative detection of the amplified audio signal. The audio signal goes to control section of TX-RX unit (X57627 B/2) from display unit (X54-333). The transmit audio signal goes to the input of the multiplexer IC (IC605) for microphone muting. The audio signal is amplified by IC610, input to the AINL terminal of CODEC IC (IC614), and audio processed by DSP (IC618). The processed audio signal from the AOUTL terminal of IC614 is amplified by IC616 (A/2) to a sufficient level, anti-aliasing filtered by IC616 (B/2), and amplified by the summing amplifier IC611 (A/2).
3-2. Modulation Level Adjustment Circuit The output of the summing amplifier IC611 (A/2) is passed to an electronic volume (IC615) for maximum deviation adjustment before being applied to a varactor diode in the voltage controlled oscillator (VCO) A2 located in TX-RX unit (X57-627 A/2). Display unit (X54 B/2)
Display unit (X54 A/2) VR501
MIC JACK
IC501(A/2)
Q501,502
AMP
ATT
MI
J601 DET D501,502
TXRX unit (X57 B/2): CONTROL
MIC
IC605 (A/2)
IC610
SW
AMP
IC614 CODEC IC AINL
MIS TA
TAS
IC616 (B/2)
IC616 (A/2)
IC611 (A/2)
AMP
LPF
AMP
AOUTL IC605 (B/2)
TXI TXO SW
D-SUB TD TDS
Fig. 2 Microphone circuit
18
IC615 MO DAC MB
SW
TKR-850 CIRCUIT DESCRIPTION 3-3. Driver and Final Power Amplifier Circuit The transmit signal is generated by the TX VCO (A2), amplified by Q11, and sent to final unit (X45-363). This amplified signal is amplified by Q1, Q2, Q3, and Q4, and is passed to the FINAL stage. The RF power amplifier consists of MOS FET. Final unit (X45-363 A/2)
TX-RX unit (X57-627 A/2)
TX ANT Q1 Drive AMP
STT Q11 MO
Q3 Q4 Q5 Drive AMP Drive AMP Final AMP
ATT
TX VCO A2 (X58-481)
CM COUPLER TEMP Q2 Drive AMP
Vcont D4 IC3
FCT MB
BUFF
TCXO
IC1
X3 16.8MHz
DC AMP
REF DET
FWD DET
D5
SW Q8 POWER ADJ
PC
Fig. 3
REF AMP IC3
VR1
Driver and final power amplifier circuit
3-4. Automatic Power Control, Circuit and Transmitter The automatic power control (APC) circuit stabilizes the transmitter output power at a pre-determined level, and consists of forward/reflected power detector circuits, and switching transistor Q8. The forward/reflected power detector circuits detects forward RF power and reflected RF power to DC voltage, and consists of a CM coupling type detection circuit formed by a strip line, RF detector D4/D5, and DC amplifier IC3 (A/2). The voltage comparator (IC3 B/2) compares the above detected voltage with a reference voltage, set using the microprocessor and IC6 located in the TX-RX unit. An APC voltage proportional to the difference between the sensed voltage and the reference voltage appears at the output of IC3. This output voltage controls the gate voltage for the drive amplifier Q4 and final amplifier Q5, which keeps the transmitter output power constant.
FAN
X45 A/2
CN4 FAB
X57 A/2 IC7 BU4094BCF
+B
IC604
Q9
FAG
FAS
13
CPU
Q6 CK, DT, STB
IC1 TK11050M 6 OUT
TEMP 17
VTH Q602
[Fan operation] ON
3-5. Fan Action Control Circuit If fan action is set to “Temperature”, the cooling fan is turned ON or OFF according to temperature. If the ambient temperature of the final unit exceeds approx. 40°C, the output from pin 6 of the temperature detection IC1 changes from L to H. This signal is sent to the CPU (IC604) by Q602 in the TX-RX unit B/2 (control section), and the output from pin 13 (FAS) of IC7 in the TX-RX unit A/ 2 controlled by the CPU goes H. This signal turns Q9 in the final unit ON to run the cooling fan. It has a hysteresis of approx. 5°C by IC2. If fan action is set to “Continuous”, the fan operates continuously, but Q9 stays ON.
X57 B/2
OFF +20°C
+30°C
+40°C
+50°C
Fig. 4 Fan action control circuit
19
TKR-850 CIRCUIT DESCRIPTION 4-2. Transmitter PLL
4. PLL Frequency Synthesizer The PLL frequency synthesizer circuit consists of the following circuits : 4-1 receiver PLL circuit, 4-2 transmitter PLL circuit, and 4-3 unlocked detector circuit.
4-1. Receiver PLL The receiver PLL circuit is located in VCO unit A3 (X58480) on TX-RX unit (X57-627 A/2), and consists of VCXO X2, VCO’s (Q350 and Q351), a single-chip PLL IC IC300, buffer amplifier Q355, and high-frequency amplifier Q302. The VCXO generates 16.8MHz. The frequency stability is within ± 1.5ppm (Temperature range of –30 to +60°C). The frequency tuning of the VCXO is done to apply a voltage to pin 1 of the VCXO. The output of the VCXO is applied to pin 8 of the PLL IC through the pin 7 of the VCO. The first local oscillator is a lower heterodyne local oscillator, and the VCO oscillator frequency is 395.150 to 467.15MHz. The oscillator frequency is controlled by applying the VCO control voltage, obtained from the phase comparator to the varactor diodes.
TX-RX unit
VCO unit (X58-480)
The transmitter PLL circuit is located in VCO unit A2 (X58481) on TX-RX unit (X57-627 A/2), and consists of VCXO X3, VCO’s (Q350), a single-chip PLL IC IC300, buffer amplifier Q355, and high-frequency amplifier Q302. The VCXO generates 16.8MHz. The frequency stability is within ± 1.5ppm (Temperature range of –30 to +60°C). The frequency tuning and modulation of the VCXO are done to apply a voltage to pin 1 of the VCXO. The output of the VCXO is applied to pin 8 of the PLL IC through the pin 15 of the VCO. The VCO oscillator frequency is 440.00 to 512.00MHz. The oscillator frequency is controlled by applying the VCO control voltage, obtained from the phase comparator to the varactor diodes.
4-3. Unlock Detector Circuit If a pulse signal appears at the LD pin of IC300, an unlock condition occurs, causing the voltage applied to the pin of the microprocessor to go low. The names of this pin are LDT for TX PLL and LDR for RX PLL. When the microprocessor detects this condition, the transmitter is disabled.
TX-RX unit
VCO unit (X58-481)
Q350
Q355
Q350
Q355
VCO A
AMP
VCO A
AMP
Q354 SW
MO
SW Q352
MO
MO
SW Q353 SRR VCO B Q351 Q300
IC300
Q302
X2
Q300
IC300
Q302
X3
LPF
PLL-IC
AMP
VCXO
LPF
PLL-IC
AMP
VCXO
CP,DP EPR,LDR µ-com
µ-com
IC604
IC604
Fig. 5 Receiver PLL
20
CP,DP EPT,LDT
Fig. 6 Transmitter PLL
TKR-850 CIRCUIT DESCRIPTION 5-5. Display Circuit
5. Control Circuit
The display circuit (X54-333) contains two 7-segment LEDs D506, D507 (orange : see the operation manual for details of display), D503 (red : transmission), D504 (green : busy), two-color LED D505 (red : backup, green : main DC), LEDs in switches S501 to S506, IC502, IC503, IC504, and IC505 to display this model channels and states. IC502 to IC505 are shift registers which convert serial data from the CPU to parallel data and light LEDs. Q507, Q510, and Q511 are switching transistors which control two-color LED D505. IC506, and IC507 are three-pin power supply ICs which produce power used for the display circuit.
The control circuit mainly located in the control section of TX-RX unit (X57-627 B/2) consists of the following : 5-1 CPU, 5-2 memory circuit, 5-3 CPU clock shift, 5-4 shift register circuit, 5-5 display circuit, 5-6 DSP circuit, 5-7 base-band circuit, 5-8 RS-232C circuit, and 5-9 power supply circuit.
5-1. CPU The CPU (IC604) is a 16bit single-chip microcomputer containing a 32k ROM and 3k RAM. This CPU controls the flash ROM, the DSP, the receiver circuit, the transmitter circuit, the control circuit, and the display circuit and transfers data to or from an external device.
TX-RX unit (X57 B/2): CONTROL
5-2. Memory Circuit
IC600
IC609 has a flash ROM with a capacity of 2M bits that contains the control program for the CPU, the signal processing program for DSP and data such as channels and operating features. This program can be easily written from an external device. Data such as the operating status are programmed into the EEPROM (IC600).
IC604
EEPROM
FLASH ROM
IC601
IC620
Reset IC
232C DRIVER CPU
X600
IC602/623
Q600 SW
There are the 14.754MHz clock for the CPU (IC604) and the 16.515MHz clock for the DSP (IC618) at the control section of TX-RX unit (X57-627). When these clocks are multiplexed with the reception frequency, they become an internal beat signal. To prevent this, by tuning Q600 and Q604 on the clock frequency is shifted. (Shift on/off can be set through programming.)
IC615 D/A IC
14.754 MHz
5-3. CPU Clock Shift
IC609
Shift Register IC
BEAT SHIFT IC603/606 INTERFACE IC IC618
X601 16.515 MHz
DSP IC613
5-4. Shift Register Circuit
Q600 SW
DIVIDER IC614
Serial data is sent to the shift register (IC502 to IC505 located in display unit, IC602, IC623, IC7 located in TX-RX unit) from the CPU (IC604) to control various functions in the unit.
BEAT SHIFT
CODEC IC
Fig. 7 Control circuit Display unit (X54-333-20 A/2) PF1~6
CLK,SOE, STB1
CLK,SOE, STB1 SI SO
Shift Reg. 1 BU4094BCFV
CLK,SOE, STB1 SI SO
Shift Reg. 2 BU4094BCFV
SW
KEY1~5
CLK,SOE, STB1 SI
Shift Reg. 3 BU4094BCFV
DAT
SO
Shift Reg. 4 BU4094BCFV
SW
SW
SW
KEY LAMP 1~6
TX
SW
SW
BUSY Main DC/ BACKUP
Fig. 8 Display circuit 21
TKR-850 CIRCUIT DESCRIPTION 5-6. DSP The DSP circuit filters transmit/receive audio signal and encode/decodes signaling (QT, DQT). This circuit consists of IC618, IC612, IC613, IC614, IC603, IC606, IC608, IC610, IC616, and IC619. The receive signal DET is converted from analog to digital by IC614 with a sampling frequency of 16.128kHz. The digitized audio signal is sent to DSP IC618 to process the signaling signal and audio signal. The processed digital audio signal is fed to CODEC IC613, converted from digital to analog, and the analog signal is output from pin 16 (AOUTR). Then, the audio signal is amplified by IC619 (B/2), passes through the IC619 (A/2) low-pass filter, and goes to an electronic volume IC615. The transmit audio signal coming from IC605 is amplified by IC610, fed to pin 3 (AINL) of CODEC IC614, and converted from analog to digital at a sampling frequency of 16.128kHz. The digitized transmit audio signal is AGC-processed, pre-emphasized and filtered at 300Hz to 3kHz by DSP IC618, and the resulting signal is fed back to CODEC IC614, and converted from digital to analog, and the analog signal is output from pin 15 (AOUTL). The transmit signal from AOUTL is amplified by IC616 (B/2), passes through the IC616 (A/2) low-pass filter, and goes to the IC611 (A/2) summing amplifier. IC613 is a counter IC and the clock required for the CODEC and DSP is generated by dividing the 16.515MHz clock signal produced by DSP IC618. IC603 and IC606 are interface IC between the CPU operated at 5.0V and the DSP operated at 3.3V.
6. DC Power Supply Circuit 6-1. DC Source Switching Relay Circuit 1. The final unit contains a relay (K1) for switching between the Main DC and Backup Battery. If an external power source is connected to the Main DC terminal, the Backup terminal is isolated by the relay. If the Main DC turns OFF due to power failure, it is switched to the Backup terminal by the relay. The CPU monitors which is used, Main DC or Backup Battery. 2. Trickle charge circuit If both Main DC and Backup Battery are connected, trickle charging of 0.5 A max. can be performed from the Main DC power supply to the Battery. (The default is OFF. See the Modification section for information on the modification method.) The battery is charged from the Main DC with D8, D9 and R61. If it exceeds 0.5 A, the charging circuit is turned OFF by D9. Main DC
R54
D8 D9
+B
R61 K1 (Relay)
120mA
Land Backup battery
Final unit (A/2) TX-RX unit (A/2) TX-RX unit (B/2)
5-7. Base-Band Circuit The base-band circuit switches between the modulation signal to the transmitter circuit, and remote audio and adjusts their levels. This circuit consists of IC605, IC607, IC611, IC615, and IC617. Modulation inputs include local microphone input, lowspeed data (LSD), high-speed data (HSD), external audio input (TA), and external data input (TD), and demodulation outputs include receive audio output (RA), and receive data output (RD). The multiplexer (IC605) changes signals, the electronic volume (IC615) adjusts the level, and the operational amplifier (IC607, IC611, IC617) amplifiers and sums signals.
5-8. RS-232C Circuit The RS-232C circuit connects the RS-232C serial port of a personal computer directly to this model to perform FPU operation. The FPU operation can also be performed by connecting a programming cable (KPG-46) to the local microphone on the front panel. But, if the D-sub connector on the rear panel is used, the programming cable is not required. The 232C driver IC (IC620) changes the TTL-232C level. The firmware can only be rewritten with the local microphone on the front panel.
5-9. Power Supply Circuit
22
The power supply circuit generates power to operate the CPU, DSP, flash ROM, bi-directional buffer, and base-band circuit. This circuit consists of IC624, IC625, IC626, IC627, IC628, and IC630.
BUP
16
IC604 CPU Q601
Fig. 9 DC source switching relay circuit 6-2. SB Switching Relay Circuit 1. SB (Switched +B) is supplied through the relay (K1) in the TX-RX unit A/2. When S507 (DC source switch) in the display unit is turned ON, the relay (K1) is turned ON to output SB. 2. If +B exceeds 18V, the relay is forcibly turned OFF by D12 and Q25 to interrupt the power and protect the main unit. K1
+B R165 D12
SB R166
Q25 Q24
S507
Land (PSW)
Display unit (Front panel)
Fig. 10 SB switching relay circuit
TKR-850 SEMICONDUCTOR DATA Main CPU : 30622M4-113GP (TX-RX unit IC604) ■ Pin Function Pin No.
Name
I/O
Function
1~5
IO5~IO1
I/O
Aux I/O No.5~No.1 (Acc D-sub 25 pin)
40
HLDA
–
Not used
6
BYTE
5V
41
BCLK
O
Not used
–
Pin No.
Name
I/O
Function
7
CNVss
–
GND
42
RD
O
Flash ROM WR/DSP HDS1
8
ENT
O
TX PLL IC enable
43
BHE
–
Not used
9
ENR
O
RX PLL IC enable
44
WR
O
Flash ROM WR/DSP HDS2
10
Reset
I
Microcomputer reset input
45
STB2
O
Control shift register STB
11
Xout
–
14.7456MHz
46
INTx
O
DSP interrupt
12
Vss
–
GND
47
HCS
O
DSP HCS
13
Xin
–
14.7456MHz
48
CS0
O
Flash ROM CS
14
Vcc
–
5V
49
A19
O
Not used
15
NMI
–
Not used
50~59
A18~A9
O
Flash ROM address bus
16
BUP
I
Backup battery detect
60
Vcc
–
5V
H : Backup, L : Main
61
A8
O
Flash ROM address bus
Temperature detect for fan action
62
Vss
–
GND
H : Temp high, L : Temp low
63~70
A7~A0
O
Flash ROM address bus
Acc PTT (Acc D-sub 25 pin)
71
EMON
I
Acc monitor (Acc D-sub 25 pin)
17
18
TEMP
EPTT
I
I
H : Off, L : On 19
CLK
O
H : Off, L : On
H : Off, L : On
Common clock
72
LDR
I
RX VCO lock detect
73
LDT
I
TX VCO lock detect
20
DAT
O
Common data
21
SFT
O
Beat shift
H : Lock, L : Unlock
22
LD1
O
Control D/A converter LD
23
STB3
O
Control shift register STB
74,75
KEY5,KEY4
O
Key matrix output
24
LD2
O
TX/RX D/A converter LD
76~78
KEY3~KEY1
I
Key matrix input
25
STB4
O
TX/RX shift register STB
79~86
D7~D0
26
RS
O
DSP reset
87
FWD
I
RF power down level input
27
SC
O
Squelch control (Acc D-sub 25 pin)
88
RSSI
I
RSSI level input
H : Inactive, L : Active
89
ASQ
I
Squelch level input
28
PTT
I
Mic PTT
90
VLI
I
Volume level input
29
TXD1
O
Mic TXD
91
BATT
I
Power supply voltage level input
30
RXD1
I
Mic HOOK/RXD
92
AI1
I
Aux input No.1 (Acc D-sub 25 pin)
31
SCLK
O
EEPROM clock
93
AI2
I
Aux input No.2 (Acc D-sub 25 pin)
32
SDAT
I/O
EEPROM data
94
AVss
–
GND
33
TXD0
O
Acc TXD (Acc D-sub 25 pin)
95
AI3
I
Aux input No.3 (Acc D-sub 25 pin)
34
RXD0
I
Acc RXD (Acc D-sub 25 pin)
96
Vref
–
5V
35
CP
O
PLL IC clock
97
AVcc
–
5V
36
DP
O
PLL IC data
98
STB1
O
Display shift register STB
37
RDY
I
CPU ready input
99
SOE
O
Shift register common OE
38
ALE
–
Not used
100
IO6
I/O
Aux I/O No.6 (Acc D-sub 25 pin)
39
HOLD
–
Not used
H : On, L : Off
H : Off, L : On
H : Off, L : On
H : Lock, L : Unlock
I/O
Flash ROM data bus
23
TKR-850 SEMICONDUCTOR DATA DSP : 320VC5402PGE (TX-RX unit IC618) ■ Pin Function Pin No.
24
Name
I/O
1,2
NC1,NC2
–
Not used (No connection)
3
Vss
–
GND
4
DVDD
–
VDD for I/O pins (+3.3V)
45
BDR0
I
Serial data receive input
5
A0
O
Not used (No connection)
46
HCNTL1
I
HPI control 1
6
HD0
HPI data bus
47
BDR1
–
Not used (No connection)
7~11
A1~A5
O
Not used (No connection)
48
BCLKX0
I
Transmit clock input
12
NC3
–
Not used (No connection)
13
HAS
I
HPI address strobe (Pull up)
14
Vss
–
GND
15
NC4
–
Not used (No connection)
50
Vss
–
GND
16
CVDD
–
VDD for core CPU (+1.8V)
51
HINT/TOUT1
O
Boot mode select (Pull up)
17
HCS
I
HPI chip select
52
CVDD
–
VDD for core CPU (+1.8V)
18
HR/W
I
HPI read/write
53
BFSX0
I
Frame sync. for transmitter input
19
READY
I
Data ready (Pull up)
20
PS
O
Not used (No connection)
21
DS
O
Not used (No connection)
22
IS
O
Not used (No connection)
55
HRDY
–
Not used (No connection)
23
R/W
O
Not used (No connection)
56
DVDD
–
VDD for I/O pins (+3.3V)
24
MSTRB
O
Not used (No connection)
57
Vss
–
25
IOSTRB
O
Not used (No connection)
58
HD1
I/O
HPI data bus
26
MSC
O
Not used (No connection)
59
BDX0
O
Serial data transmit output
27
XF
O
CODEC control
60
BDX1
–
Not used (No connection)
H : Power down, L : Active
61
IACK
–
Not used (No connection)
I/O
Function
Pin No. 44
Name BFSR1
I/O I
Function Frame sync. for receiver input (LRCK : 16.128kHz)
(SCLK : 516.09375kHz) 49
BCLKX1
O
Master clock output (MCLK : 4.12875MHz)
(LRCK : 16.128kHz) 54
BFSX1
I
Frame sync. for transmitter input (LRCK : 16.128kHz)
GND
28
HOLDA
–
Not used (No connection)
62
HBIL
I
Byte identification (HPI)
29
IAQ
–
Not used (No connection)
63
NMI
I
Not used (Pull up)
30
HOLD
I
Hold (Pull up)
64
INT0
I
Command interrupt from host CPU
31
BIO
I
Serial data syncronize input
65
INT1
I
Not used (Pull up)
32
MP/MC
I
Not used (Pull down)
66
INT2
I
Boot mode select (Pull up)
33
DVDD
–
VDD for I/O pins (+3.3V)
67
INT3
I
Not used (Pull up)
34
Vss
–
GND
68
CVDD
–
VDD for core CPU (+1.8V)
35~38
NC5~NC8
–
Not used (No connection)
69
HD2
I/O
39
HCNTL0
I
HPI control 0
70
Vss
–
GND
40
Vss
–
GND
71~74
NC9~NC12
–
Not used (No connection)
41
BCLKR0
I
Receive clock input
75
DVDD
–
VDD for I/O pins (+3.3V)
(SCLK : 516.09375kHz)
76
Vss
–
GND
42
BCLKR1
–
Not used (No connection)
77
CLKMD1
I
Clock mode select (Pull down)
43
BFSR0
I
Frame sync. for receiver input
78
CLKMD2
I
Clock mode select (Pull up)
(LRCK : 16.128kHz)
79
CLKMD3
I
Clock mode select (Pull down)
HPI data bus
TKR-850 SEMICONDUCTOR DATA / DESCRIPTION OF COMPONENTS Pin No.
Name
I/O
80
NC13
–
81
HD3
I/O
82
TOUT0
–
83
EMU0
84
EMU1/OFF
85
TDO
86
TDI
Function Not used (No connection)
Final Unit (X45-3630-XX) Ref No.
Part name
Description
HPI data bus
IC1
IC
Thermostat
Not used (No connection)
IC2
IC
Voltage regulator
I/O
Emulator 0 (to JTAG connector)
IC3
IC
DC amplifier
I/O
Emulator 1 (to JTAG connector)
Q1,2
Transistor
RF amplifier
O
Test data output (to JTAG connector)
Q3
FET
RF amplifier
I
Test data input (to JTAG connector)
Q4
FET
TX drive amplifier
87
TRST
I
Test reset (to JTAG connector)
Q5
FET
Final amplifier
88
TCK
I
Test clock (to JTAG connector)
Q7
FET
RF switch
89
TMS
I
Test mode select (to JTAG connector)
Q8,9
Transistor
DC switch
90
NC14
–
Not used (No connection)
D2
Zener diode
Voltage reference
91
CVDD
–
VDD for core CPU (+1.8V)
D3
Diode
Surge absorption
92
HPIENA
I
Not used (Pull up)
D4,5
Diode
RF detector
93
Vss
–
GND
D7
Zener diode
Surge protector
94
CLKOUT
O
Not used (No connection)
D8
Diode
Reverse current protection
95
HD4
HPI data bus
D9
Varistor
Current protector
96
X1
I/O –
16.515MHz (System clock)
D10
Diode
Surge protector
97
X2/CLKIN
–
16.515MHz (System clock)
D51,52
Diode
Reverse connection protection
98
RS
I
DSP reset input
99~104
D0~D5
–
Not used (No connection)
105
A6
O
Not used (No connection)
106
Vss
–
GND
107~109
A7~A9
O
Not used (No connection)
110
NC15
–
Not used (No connection)
111
Vss
–
GND
112
DVDD
–
VDD for I/O pins (+3.3V)
113~119
D6~D12
–
Not used (No connection)
120
HD5
121~123
D13~D15
124
HD6
125
CVDD
–
VDD for core CPU (+1.8V)
126
NC16
–
Not used (No connection)
127
HDS1
I
HPI data strobe 1 (Pull up)
128
Vss
–
GND
129
HDS2
I
HPI data strobe 2 (Pull down)
130
DVDD
–
VDD for I/O pins (+3.3V)
131~134
A10~A13
O
Not used (No connection)
135
HD7
136~141
A14~A19
O
Not used (No connection)
142
CVDD
–
VDD for core CPU (+1.8V)
143,144
NC17,NC18
–
Not used (No connection)
I/O – I/O
I/O
HPI data bus Not used (No connection) HPI data bus
HPI data bus
Display Unit (X54-3330-20) Ref No.
Part name
Description
IC501
MOS IC
MIC amplifier
IC502~505
MOS IC
Shift registers
IC506,507
MOS IC
Voltage regulator
Q501,502
Transistor
Level controller
Q504
FET
DC switch
Q506
Transistor
DC switch
Q507
FET
DC switch
Q508
Transistor
DC switch
Q510,511
Transistor
DC switch
Q512~514
FET
DC switch
Q516~519
FET
DC switch
Q521~525
FET
DC switch
D501,502
Diode
AF detector
D503~505
LED
LED
D506,507
LED
7 segment
D508~514
Diode
Surge absorption
D601,602
Diode
Surge absorption
D603
Varistor
Current protector
25
TKR-850 DESCRIPTION OF COMPONENTS TX-RX Unit (X57-6270-XX) Ref No.
26
Part name
Ref No. Description
Part name
Description
Q601
Transistor
DC switch
IC1,2
IC
Buffer amplifier
Q602
FET
DC switch
IC3~5
IC
Voltage regulator
Q603
Transistor
Inverter
IC6
IC
D/A converter
Q604
FET
DC switch
IC7
IC
Shift register
Q605
Transistor
Inverter
IC9
IC
FM IF system
Q606
Transistor
AF mute switch
IC10,11
IC
Voltage regulator
Q609
Transistor
DC switch
IC600
IC
EEPROM
Q610
FET
DC switch
Transistor
DC switch
IC601
IC
Voltage detector
Q611
IC602
IC
Shift register
D1~4
Diode
Wide/Narrow switch
IC603
IC
Bus transceiver
D5
Diode
Noise detection
IC604
MPU
CPU
D7
Diode
DC switch
IC605
IC
Multiplexer
D8
Diode
TX switch
IC606
IC
Bus transceiver
D9
Diode
Surge protector
IC607,608
IC
AF amplifier
D11
Zener diode
Surge protector
IC609
IC
Flash ROM
D12
Zener diode
Voltage reference
Diode
Surge protector
IC610,611
IC
AF amplifier
D600
IC612
IC
Inverter
D601
Diode
Voltage reduction
IC613
IC
Counter
D606~625
Diode
Surge protector
IC614
IC
CODEC
D626
Varistor
Current protector
IC615
IC
D/A converter
D627,628
Diode
reverse current protector
IC616,617
IC
AF amplifier
D629
Diode
Surge protector
IC618
MPU
DSP
IC619
IC
AF amplifier
IC620
IC
RS-232C transceiver
IC621
IC
NAND gate
IC300
IC
PLL
IC622
IC
Multiplexer
Q300,301
Transistor
Active filter
IC623
IC
Shift register
Q302
Transistor
Buffer amplifier
IC624~628
IC
Voltage regulator
Q350,351
FET
VCO OSC
IC629
IC
Audio amplifier
Q352~354
Transistor
DC switch
IC630
IC
Voltage regulator
Q355
Transistor
Buffer amplifier
Q1~3
Transistor
RF amplifier
D350~353
Varicap
Frequency control
Q4
Transistor
Wide/Narrow switch
Q5,6
Transistor
DC switch
Q7
Transistor
Noise amplifier
RX PLL/VCO Unit (X58-4800-XX) Ref No.
Part name
Description
TX PLL/VCO Unit (X58-4810-XX) Ref No.
Part name
Description
Q8,9
Transistor
RF amplifier
IC300
IC
PLL
Q10
Transistor
Current control
Q300,301
Transistor
Active filter
Q11
Transistor
RF amplifier
Q302
Transistor
Buffer amplifier
Q12~15
Transistor
Ripple filter
Q350
FET
VCO OSC
Q16~19
Transistor
DC switch
Q355
Transistor
Buffer amplifier
Q20
Transistor
Inverter
D350,352
Varicap
Frequency control
Q23~25
Transistor
DC switch
D354
Varicap
Modulation
Q600
FET
DC switch
TKR-850 PARTS LIST New Parts. indicates safety critical components. * Parts without Parts No. are not supplied.
L : Scandinavia Y : PX (Far East, Hawaii) Y : AAFES (Europe)
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert.
K : USA T : England X : Australia
P : Canada E : Europe M: Other Areas TKR-850 FINAL UNIT (X45-3630-XX)
Ref. No.
New Address parts
Parts No.
Destination
Description
TKR-850 1 2 3 4 5
2B 1B 1B 1D 3A
✽ ✽ ✽ ✽ ✽
A10-4037-01 A62-0836-04 A62-0837-04 A62-0840-03 A62-0933-13
CHASSIS PANEL PANEL PANEL PANEL ASSY
6
3C
✽
A62-0934-03
PANEL ASSY
8 10 11 12
1F 1F 1F 2C,3D
✽ ✽ ✽ ✽ ✽
B10-2635-04 B10-2636-04 B11-1259-04 B62-1327-10 B72-1935-04
FRONT GLASS F-KEY FRONT GLASS PC SHEET FILTER F-KEY INSTRUCTION MANUAL MODEL NAME PLATE
K
12 12
2C,3D 2C,3D
✽ ✽
B72-1936-04 B72-1937-04
MODEL NAME PLATE MODEL NAME PLATE
K2 E
14 15 16 17 18
2C 1C 2C 1E 1E
✽ ✽ ✽ ✽
E30-3414-05 E30-3418-05 E30-3419-05 E30-3427-15 E31-3228-05
DC CORD ANTENNA CABLE (BNC) ANTENNA CABLE (N) DC CORD ACC LEAD WIRE WITH CONNECTOR LEAD WIRE WITH CONNECTOR LEAD WIRE WITH TERMINAL (DC +) LEAD WIRE WITH TERMINAL (DC -) LEAD WIRE WITH CONNECTOR (D-SUB) LEAD WIRE WITH CONNECTOR (SP)
ADC12 TX-RX FINAL OUTER
20 21 22 23
1B 1B 2C 3B
✽ ✽ ✽ ✽
E37-0808-05 E37-0902-05 E37-0903-05 E37-0904-05 E37-0905-05
24 25 26 27 28
3A 3A 1B 1B 1B
✽ ✽ ✽ ✽ ✽
E37-0906-05 E37-0908-05 E37-0909-05 E37-0911-05 E37-0912-05
LEAD WIRE WITH CONNECTOR (CONT-DISP) LEAD WIRE WITH CONNECTOR (11P) LEAD WIRE WITH CONNECTOR (8P) LEAD WIRE WITH CONNECTOR (3P) LEAD WIRE WITH MINIPIN PLUG
29 30 33
2C 1B
2B
✽ ✽ ✽ ✽ ✽
E37-0913-05 E37-0934-05 E37-0964-05 E37-0965-05 E37-0967-05
LEAD WIRE WITH CONNECTOR (15P) LEAD WIRE WITH TERMINAL (ORANGE) LEAD WIRE WITH TERMINAL (BLACK) LEAD WIRE WITH TERMINAL (RED) FLAT CABLE (36P)
34
2C
✽
E70-0402-05
36 37 38 -
1C,1E 2C 1C
Ref. No.
New Address parts
Parts No.
Description
55 56 57
1E 1F 3F
✽ ✽
H25-0762-04 H25-2328-04 H52-1779-02
PROTECTION BAG (120X300) PROTECTION BAG (80/250/0.07) ITEM CARTON CASE
59 60 61 62
1E 1E 1F 1E
✽ ✽ ✽
J02-0475-05 J02-0492-04 J21-8402-04 J59-0302-05
FOOT FOOT HARDWARE FIXTURE (ACC) GROMMET
64 65 66 67
1E 3A 3A 3A
✽ ✽ ✽
K01-0418-05 K29-5389-03 K29-5460-02 K29-9106-04
HANDLE (ACC) KNOB (VOL) KEY TOP KNOB (DC SOURCE)
A B C D E
2C 2C 1C,2C 2A,1E 2B,2C
N09-2292-05 N15-1030-46 N30-2606-46 N30-4006-46 N30-4014-46
HEXAGON HEAD SCREW FLAT WASHER PAN HEAD MACHINE SCREW PAN HEAD MACHINE SCREW PAN HEAD MACHINE SCREW
F G H J K
1C 2C 3B 1B 1E
N30-4020-45 N32-3006-46 N32-4008-45 N33-3006-45 N35-3006-45
PAN HEAD MACHINE SCREW FLAT HEAD MACHINE SCREW FLAT HEAD MACHINE SCREW OVAL HEAD MACHINE SCREW BINDING HEAD MACHINE SCREW
L M N O P
2C 1C 1B,3B 1C,2C 3A
N35-3014-46 N35-4006-45 N67-3008-46 N87-2606-46 N87-3005-45
BINDING HEAD MACHINE SCREW BINDING HEAD MACHINE SCREW PAN HEAD SEMS SCREW W BRAZIER HEAD TAPTITE SCREW BRAZIER HEAD TAPTITE SCREW
Q
2B,3B
N87-3006-46
BRAZIER HEAD TAPTITE SCREW
69
3A
T07-0247-05
SPEAKER
✽
✽
✽ ✽
FINAL UNIT (X45-3630-XX)
-10 : K,E -11 : K2
TERMINAL BOARD
C1 C3 C4,5 C6,7 C8
CC73GCH1H100D C90-2146-05 CK73FB1E104K CK73GB1H471K CC73GCH1H030C
CHIP C ELECTRO CHIP C CHIP C CHIP C
10PF 100UF 0.10UF 470PF 3.0PF
D 25WV K K C
✽ ✽
F05-1537-05 F09-0445-05 F09-0471-05 F10-2374-04 F10-2379-04
FUSE (BLADE) (15A/32V) CAP (D-SUB) FANMOTOR SHIELDING PLATE (TX-RX) SHIELDING CASE (TX-RX COM)
C9 C10 C12-15 C16 C17
CK73FB1E104K CK73GB1H471K CK73GB1H471K CK73FB1E104K CC73GCH1H270J
CHIP C CHIP C CHIP C CHIP C CHIP C
0.10UF 470PF 470PF 0.10UF 27PF
K K K K J
✽ ✽
F10-2409-04 F20-3322-04
SHIELDING CASE (TX-RX FOIL) INSULATING SHEET
CHIP C CHIP C CHIP C CHIP C CHIP C
39PF 470PF 470PF 12PF 9.0PF
J K K J D
✽ ✽ ✽
FLAT SPRING FLAT SPRING EARTH SPRING FIBROUS SHEET (CHASSIS) FIBROUS SHEET (PANEL)
CC73GCH1H390J CK73GB1H471K CK73FB1H471K CC73FCH1H120J CC73FCH1H090D
3B 2B,3B 3C,2D
G02-0576-14 G02-0829-14 G02-0885-13 G10-1263-04 G10-1264-04
C17 C18,19 C20 C21 C22
49 50 -
1F 1F
✽ ✽ ✽
G13-1801-04 G13-1802-04 G13-1886-04
CUSHION (ACC) CUSHION (ACC) CUSHION
C23 C24 C25 C26 C27
CK73FB1H471K C90-2143-05 CK73FB1E104K CC73GCH1H101J CK73GB1H471K
CHIP C ELECTRO CHIP C CHIP C CHIP C
470PF 47UF 0.10UF 100PF 470PF
K 25WV K J K
53 54
1E 1F
H25-0029-04 H25-0747-04
PROTECTION BAG (60/110/0.07) PROTECTION BAG (250X350)
C28 C29 C30
CK73FB1E104K CK73GB1H471K CK73FB1E104K
CHIP C CHIP C CHIP C
0.10UF 470PF 0.10UF
K K K
42 44 46 47 48
1C 1B
Destination
K2 K,E
27
TKR-850 PARTS LIST FINAL UNIT (X45-3630-XX) Ref. No.
Address New parts
Parts No.
Description
Destination
Ref. No.
New Address parts
Parts No.
Destination
Description
C117 C118 C120
CK73FB1E104K C93-0557-05 CK73FB1H103K
CHIP C CHIP C CHIP C
CN1,2 CN3 CN4 CN5 CN6-8
E04-0154-05 E40-5632-05 E40-3246-05 E40-5703-05 E23-0462-05
PIN SOCKET PIN ASSY PIN ASSY PIN ASSY TERMINAL
CN51,52
J13-0071-05
FUSE HOLDER
L1 L2 L3 L5 L6,7
L40-3963-92 L40-1875-34 L40-4763-92 L34-4602-05 L34-4517-05
SMALL FIXED INDUCTOR (3.9NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (4.7NH) AIR-CORE COIL AIR-CORE COIL
L8 L9 L11 L12 L14,15
L40-3975-34 L34-4517-05 L34-4517-05 L34-4523-05 L40-1075-34
SMALL FIXED INDUCTOR (39NH) AIR-CORE COIL AIR-CORE COIL AIR-CORE COIL SMALL FIXED INDUCTOR (10NH)
R1 R2 R3 R4 R6
RK73GB1J103J RK73GB1J472J RK73GB1J470J RK73GB1J100J RK73GB1J100J
CHIP R CHIP R CHIP R CHIP R CHIP R
10K 4.7K 47 10 10
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R7 R8 R9 R11 R12
RK73GB1J682J RK73FB2A100J RK73FB2A220J RK73GB1J333J RK73GB1J153J
CHIP R CHIP R CHIP R CHIP R CHIP R
6.8K 10 22 33K 15K
J J J J J
1/16W 1/10W 1/10W 1/16W 1/16W
K K J K K
R13 R15 R17 R18 R19
RK73FB2A220J R92-1217-05 RK73FB2A473J RK73EB2B100J RK73FB2A683J
CHIP R CHIP R CHIP R CHIP R CHIP R
22 0 OHM 47K 10 68K
J
1/10W
J J J
1/10W 1/8W 1/10W
CHIP C 470PF CHIP C 100PF CHIP C 470PF CHIP C 0.10UF ELECTROLYTIC CAP
K J K K
R20,21 R22 R23 R24 R26
R92-1252-05 R92-1215-05 RK73FB2A473J RK73FB2A563J RK73GB1J101J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 470 47K 56K 100
J J J J
1/2W 1/10W 1/10W 1/16W
C93-0599-05 C93-0555-05 C93-0556-05 C93-0560-05 C93-0555-05
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 5.0PF 6.0PF 10PF 5.0PF
K C D D C
R33 R34,35 R36 R37 R38
R92-0670-05 RK73GB1J104J R92-1252-05 R92-0670-05 RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 100K J 0 OHM 0 OHM 47K J
C91-98 C99 C100-102 C103 C104
CK73GB1H471K CK73FB1E104K CK73GB1H471K C92-0628-05 CC73GCH1H101J
CHIP C CHIP C CHIP C CHIP-TAN CHIP C
470PF 0.10UF 470PF 10UF 100PF
K K K 10WV J
R40 R41 R43 R44 R45
RK73FB2A101J R92-1252-05 RK73FB2A101J R92-0670-05 RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
100 J 0 OHM 100 J 0 OHM 1.0K J
C105 C106 C107 C108 C109
CK73GB1H471K CK73FB1E104K CC73GCH1H101J CK73FB1E104K CC73GCH1H101J
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 0.10UF 100PF 0.10UF 100PF
K K J K J
R46 R47 R48 R49 R50
R92-1252-05 RK73GB1J332J RK73GB1J471J R92-1217-05 R92-1317-05
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 3.3K J 470 J 0 OHM 18 J
C112 C113 C114 C115 C116
CK73GB1H471K CK73FB1E104K CK73GB1H471K CK73FB1E104K CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 0.10UF 470PF 0.10UF 470PF
K K K K K
R51 R52 R53 R54 R55
RK73GB1J104J RK73GB1J393J RK73GB1J154J RK73GB1J102J RK73GB1J474J
CHIP R CHIP R CHIP R CHIP R CHIP R
100K 39K 150K 1.0K 470K
C31 C32 C32 C33 C33,34
C93-0599-05 C93-0558-05 C93-0561-05 C93-0563-05 C93-0565-05
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 8.0PF 12PF 18PF 27PF
K D J J J
C34 C35 C38 C39 C41
C93-0565-05 C93-0599-05 CK73GB1H471K C93-0599-05 C93-0566-05
CHIP C CHIP C CHIP C CHIP C CHIP C
27PF 470PF 470PF 470PF 33PF
J K K K J
K2
C42 C42 C44,45 C44,45 C46
C93-0562-05 C93-0563-05 CM73F2H330J CM73F2H360J C93-0599-05
CHIP C CHIP C CHIP C CHIP C CHIP C
15PF 18PF 33PF 36PF 470PF
J J J J K
K2 K,E K2 K,E
C48 C49 C50 C51 C52
CK73GB1H471K CC73GCH1H101J CK73FB1E104K C90-2143-05 CC73GCH1H101J
CHIP C CHIP C CHIP C ELECTRO CHIP C
470PF 100PF 0.10UF 47UF 100PF
K J K 25WV J
C53 C54 C55 C57,58 C59
CK73FB1E104K C90-2146-05 C93-0599-05 CM73F2H360J C93-0563-05
CHIP C ELECTRO CHIP C CHIP C CHIP C
0.10UF 100UF 470PF 36PF 18PF
K 25WV K J J
C59 C60 C61 C64 C65,66
C93-0564-05 C93-0555-05 C93-0599-05 CK73FB1H471K CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
22PF 5.0PF 470PF 470PF 470PF
J C K K K
C67 C68 C69 C70 C71,72
CK73FB1E104K CK73GB1H471K CC73GCH1H101J CK73FB1E104K CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
0.10UF 470PF 100PF 0.10UF 470PF
C75 C77 C78 C79 C80
CK73GB1H471K CC73GCH1H101J CK73GB1H471K CK73FB1E104K C92-0777-05
C81 C83 C83 C86 C89
28
K2 K,E K2 K,E
K2 K,E K2
K2 K,E
✽
0.10UF 7.0PF 0.010UF
J J J J J
K D K
1/16W
1/16W 1/10W 1/10W 1/16W
1/16W 1/16W 1W 1/16W 1/16W 1/16W 1/16W 1/16W
K,E
TKR-850 PARTS LIST Ref. No.
New Address parts
R56 R57 R58 R59 R60
Parts No. RK73GB1J473J RK73GB1J471J RK73GB1J222J RK73GB1J471J RK73GB1J104J
CHIP R CHIP R CHIP R CHIP R CHIP R
R92-2687-05 RK73GB1J471J R12-6427-05
RESISTOR CHIP R 470 J TRIMMING POT. (47K)
S76-0426-05
RELAY
D2 D3 D4,5 D7 D8
02DZ5.1(Y) 1SS355 HSM88AS ZSA5A27 RB051L-40
ZENER DIODE DIODE DIODE ZENER DIODE DIODE
D9 D10 D51,52 IC1 IC2
MINISMDC050-02 1SS355 DSA3A1 TK11050M NJM78L05UA
VARISTOR DIODE DIODE ANALOG IC BI-POLAR IC
TA75W01FU 2SC5110(O) 2SC3356(R24) 2SK2596 2SK3075
MOS IC TRANSISTOR TRANSISTOR FET FET
2SK3478-21 2SK3478-22 2SK1824 2SC4116(Y) DTD123EK
FET FET FET TRANSISTOR DIGITAL TRANSISTOR
PTH9M04BE471TS
THERMISTOR
R61 R62 VR1
✽
K1
✽
✽
IC3 Q1 Q2 Q3 Q4 Q5 Q5 Q7 Q8 Q9
✽ ✽
TH1
Destination
Description 47K 470 2.2K 470 100K
J J J J J
1/16W
K2 K,E
New Address parts ✽
CN601 J601
1/16W 1/16W 1/16W 1/16W 1/16W
DISPLAY UNIT (X54-3330-20)
Ref. No.
FINAL UNIT (X45-3630-XX) DISPLAY UNIT (X54-3330-20) TX-RX UNIT (X57-6270-XX) Parts No.
Destination
Description
E40-6141-05 E08-0877-05
PIN ASSY MODULAR JACK
-
J31-0543-05
COLLAR (LH-5-1.5)
CP501-504 R502,503 R505 R506 R507
RK75GB1J471J R92-1252-05 RK73GB1J683J RK73GB1J103J RK73GB1J682J
CHIP-COM CHIP R CHIP R CHIP R CHIP R
470 0 OHM 68K 10K 6.8K
J
1/16W
J J J
1/16W 1/16W 1/16W
R508 R509 R510 R511,512 R513
RK73GB1J102J RK73GB1J103J RK73GB1J224J RK73GB1J103J RK73GB1J104J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 10K 220K 10K 100K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R514 R516 R517 R519 R520-526
RK73GB1J154J R92-2565-05 R92-2023-05 R92-2565-05 R92-2023-05
CHIP R 150K RESISTOR CHIP R 820 RESISTOR CHIP R 820
J
1/16W
J
1/2W
J
1/2W
R529-540 R541-544 R601 R604,605 R606
RK73GB1J102J RK73GB1J103J RK73GB1J681J RK73GB1J102J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
VR501 VR601
R32-0643-05 R31-0630-05
SEMI FIXED VARIABLE RESISTOR VARIABLE RESISTOR
S501-506 S507
S70-0410-15 S68-0410-05
TACT SWITCH PUSH SWITCH
HSM88AS LA-501DD DA204U DA204U MINISMD020
DIODE LED DIODE DIODE VARISTOR
IC501 IC502-505 IC506,507 Q501 Q502
NJM4558E BU4094BCFV TA78L05F 2SC4116(Y) 2SA1586(Y,GR)
MOS IC MOS IC MOS IC TRANSISTOR TRANSISTOR
Q504 Q506 Q507 Q508 Q510,511
UPA672T DTA114EUA UPA672T DTA114EUA DTA114EUA
FET DIGITAL TRANSISTOR FET DIGITAL TRANSISTOR DIGITAL TRANSISTOR
Q512-514 Q516-519 Q521-524 Q525
UPA672T UPA672T UPA672T 2SK1824
FET FET FET FET
D501,502 D506,507 D508-514 D601,602 D603
✽
✽
1.0K 10K 680 1.0K 47K
D503-505
B30-2151-05
LED (RED/GREEN)
C501 C502,503 C504,505 C506 C507,508
C92-0628-05 C92-0501-05 CK73GB1C104K CC73GCH1H470J CK73GB1C104K
CHIP-TAN CHIP-TAN CHIP C CHIP C CHIP C
10UF 1.5UF 0.10UF 47PF 0.10UF
10WV 10WV K J K
C509 C510 C511,512 C513-518 C519,520
CK73GB1H103K C92-0628-05 CK73GB1E103K CC73GCH1H101J CK73GB1E103K
CHIP C CHIP-TAN CHIP C CHIP C CHIP C
0.010UF 10UF 0.010UF 100PF 0.010UF
K 10WV K J K
C521 C522 C523 C524 C525
C92-0628-05 CK73GB1C104K CK73FB1E334K C92-0628-05 CK73GB1C104K
CHIP-TAN CHIP C CHIP C CHIP-TAN CHIP C
10UF 0.10UF 0.33UF 10UF 0.10UF
10WV K K 10WV K
CK73FB1E334K CC73GCH1H101J CK73GB1H102K CC73GCH1H101J CC73GCH1H101J
CHIP C CHIP C CHIP C CHIP C CHIP C
0.33UF 100PF 1000PF 100PF 100PF
K J K J J
C2 C3 C3 C4,5 C7
CC73GCH1H040C CC73GCH1H070D CC73GCH1H180J CK73GB1H471K CC73GCH1H050C
CHIP C CHIP C CHIP C CHIP C CHIP C
4.0PF 7.0PF 18PF 470PF 5.0PF
C D J K C
CK73GB1C104K
CHIP C
0.10UF
K
E40-6140-05 E40-6102-05
PIN ASSY PIN ASSY
C13 C14,15 C24 C25
CK73GB1H471K CC73GCH1H060D C92-0519-05 C92-0628-05
CHIP C CHIP C CHIP-TAN CHIP-TAN
470PF 6.0PF 1.0UF 10UF
K D 25WV 10WV
C526 C601 C602 C603 C606
✽
✽
C607 CN501 CN502
✽ ✽
TX-RX UNIT (X57-6270-XX)
-10 : K,E -11 : K2 K2 K2 K,E
29
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) Ref. No.
Address New parts
Parts No.
Description
Destination
Ref. No.
New Address parts
Parts No.
Description
C28,29 C30 C31 C32 C33
CC73GCH1H020C CC73GCH1H680J CC73GCH1H331J CK73GB1H103K CC73GCH1H330J
CHIP C CHIP C CHIP C CHIP C CHIP C
2.0PF 68PF 330PF 0.010UF 33PF
C J J K J
C122,123 C124,125 C126,127 C128,129 C130,131
CK73GB1H103K C92-1341-05 C92-0633-05 CK73GB1H103K CK73GB1H102K
CHIP C ELECTRO CHIP-TAN CHIP C CHIP C
C34 C36,37 C38,39 C40,41 C42,43
CK73GB1H103K CK73GB1H103K CC73GCH1H680J CK73GB1H103K CC73GCH1H030C
CHIP C CHIP C CHIP C CHIP C CHIP C
0.010UF 0.010UF 68PF 0.010UF 3.0PF
K K J K C
C132,133 C134,135 C136-139 C140,141 C142,143
CK73GB1H471K CK73GB1H103K C90-4016-05 CK73GB1H103K CK73GB1H102K
CHIP C 470PF CHIP C 0.010UF ELECTROLYTIC CAP CHIP C 0.010UF CHIP C 1000PF
K K
C44,45 C46,47 C48 C49,50 C51
CC73GCH1H040C CC73GCH1H030C CK73GB1H103K CC73GCH1H680J CK73GB1H103K
CHIP C CHIP C CHIP C CHIP C CHIP C
4.0PF 3.0PF 0.010UF 68PF 0.010UF
C C K J K
C144 C145 C146 C147 C148
CK73GB1H471K C92-0606-05 CK73GB1H471K C92-0633-05 CK73GB1H102K
CHIP C CHIP-TAN CHIP C CHIP-TAN CHIP C
470PF 4.7UF 470PF 22UF 1000PF
K 10WV K 10WV K
C52 C53 C54 C55,56 C57
CK73GB1H103J CK73GB1H102K CK73GB1H103J CK73GB1H103K CK73GB1H103J
CHIP C CHIP C CHIP C CHIP C CHIP C
0.010UF 1000PF 0.010UF 0.010UF 0.010UF
J K J K J
C149 C150 C151 C152 C153
CK73GB1H103K C92-0633-05 C92-0008-05 CK73GB1H103K CK73GB1H471K
CHIP C CHIP-TAN CHIP-TAN CHIP C CHIP C
0.010UF 22UF 3.3UF 0.010UF 470PF
K 10WV 16WV K K
C58 C59 C60 C61 C62,63
CC73GCH1H180J CC73GCH1H150J CK73GB1H103K CC73GCH1H080D CK73GB1H103K
CHIP C CHIP C CHIP C CHIP C CHIP C
18PF 15PF 0.010UF 8.0PF 0.010UF
J J K D K
C154 C155 C156 C157 C158
C92-0560-05 CK73GB1H103K CK73GB1H102K CK73GB1H103K C92-0008-05
CHIP-TAN CHIP C CHIP C CHIP C CHIP-TAN
10UF 0.010UF 1000PF 0.010UF 3.3UF
6.3WV K K K 16WV
C64 C65 C66,67 C68-70 C71
CK73GB1C104K C92-0628-05 CC73GCH1H221J CK73GB1C104K CK73GB1H103K
CHIP C CHIP-TAN CHIP C CHIP C CHIP C
0.10UF 10UF 220PF 0.10UF 0.010UF
K 10WV J K K
C159 C160 C161-163 C164 C166,167
CK73GB1H471K CK73GB1H102K CK73GB1H103K CK73GB1H471K CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 1000PF 0.010UF 470PF 470PF
K K K K K
C72 C73,74 C75 C76 C77
C92-0628-05 CK73GB1H102K CK73GB1C223K C92-0628-05 CK73GB1H102K
CHIP-TAN CHIP C CHIP C CHIP-TAN CHIP C
10UF 1000PF 0.022UF 10UF 1000PF
10WV K K 10WV K
C171 C172 C173 C174 C175
CK73GB1H471K CK73GB1H102K CK73GB1H103K C92-0008-05 CK73GB1H102K
CHIP C CHIP C CHIP C CHIP-TAN CHIP C
470PF 1000PF 0.010UF 3.3UF 1000PF
K K K 16WV K
C78 C79 C80,81 C82-84 C85
CK73GB1C223K CK73FB1C334K C92-0628-05 CK73GB1H103K C92-0628-05
CHIP C CHIP C CHIP-TAN CHIP C CHIP-TAN
0.022UF 0.33UF 10UF 0.010UF 10UF
K K 10WV K 10WV
C176 C177 C178 C179 C184,185
CK73GB1H103K CK73GB1H471K C92-0606-05 CK73GB1H103K CK73GB1H102K
CHIP C CHIP C CHIP-TAN CHIP C CHIP C
0.010UF 470PF 4.7UF 0.010UF 1000PF
K K 10WV K K
C86 C87 C88 C89,90 C91
CK73GB1H102K C92-0628-05 CK73GB1H102K CK73GB1H103J CC73GCH1H040C
CHIP C CHIP-TAN CHIP C CHIP C CHIP C
1000PF 10UF 1000PF 0.010UF 4.0PF
K 10WV K J C
C189,190 C191-195 C196 C197 C198
CK73GB1H102K CK73GB1H103K CK73GB1H472K CK73FB1H333K CK73GB1C104K
CHIP C CHIP C CHIP C CHIP C CHIP C
1000PF 0.010UF 4700PF 0.033UF 0.10UF
K K K K K
C92,93 C94 C95 C95 C96-99
CK73GB1H471K CC73GCH1H030C CC73GCH1H040C CC73GCH1H060D CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 3.0PF 4.0PF 6.0PF 470PF
K C C D K
C199 C204-208 C209-211 C209,210 C211
CK73GB1H103K CC73GCH1H101J CC73GCH1H100D CC73GCH1H100D CC73GCH1H101J
CHIP C CHIP C CHIP C CHIP C CHIP C
0.010UF 100PF 10PF 10PF 100PF
K J D D J
C100,101 C102 C104 C105 C106
CC73GCH1H050C CK73GB1H471K CK73GB1H471K CC73GCH1H070D CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
5.0PF 470PF 470PF 7.0PF 470PF
C K K D K
C212-214 C600 C602 C605 C613,614
CK73GB1H103K CK73GB1C104K CK73GB1C104K CK73GB1C104K CK73GB1E103K
CHIP C CHIP C CHIP C CHIP C CHIP C
0.010UF 0.10UF 0.10UF 0.10UF 0.010UF
K K K K K
C107 C109 C111 C114-117 C120,121
CC73GCH1H060D CC73GCH1H120J CC73GCH1H060D CC73GCH1H100D CK73GB1H471K
CHIP C CHIP C CHIP C CHIP C CHIP C
6.0PF 12PF 6.0PF 10PF 470PF
D J D D K
C616 C623 C629 C634,635 C638
CK73GB1E103K CK73GB1C104K CC73GCH1H101J CC73GCH1H220J CK73GB1C104K
CHIP C CHIP C CHIP C CHIP C CHIP C
0.010UF 0.10UF 100PF 22PF 0.10UF
K K J J K
30
K,E K2
0.010UF 100UF 22UF 0.010UF 1000PF
Destination
K 16WV 10WV K K K K
K,E K2 K2
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) Ref. No.
New Address parts
Parts No.
Description
Destination
Ref. No.
New Address parts
Parts No.
Description
C639 C640 C641 C642 C643
CK73GB1E103K C92-0628-05 CK73GB1C104K CK73GB1E103K C92-0628-05
CHIP C CHIP-TAN CHIP C CHIP C CHIP-TAN
0.010UF 10UF 0.10UF 0.010UF 10UF
K 10WV K K 10WV
C753,754 C755 C756,757 C758 C759
C92-0628-05 CK73GB1H471K C92-0628-05 CK73FB1C105K CK73GB1H471K
CHIP-TAN CHIP C CHIP-TAN CHIP C CHIP C
10UF 470PF 10UF 1.0UF 470PF
10WV K 10WV K K
C644 C645,646 C647 C648 C649
CK73GB1E103K C92-0628-05 CC73GCH1H101J CK73GB1E103K CC73GCH1H330J
CHIP C CHIP-TAN CHIP C CHIP C CHIP C
0.010UF 10UF 100PF 0.010UF 33PF
K 10WV J K J
C760 C761 C762,763 C764,765 C766-768
CK73GB1H102K CK73GB1C104K CK73GB1H102K CK73GB1E103K CC73GCH1H101J
CHIP C CHIP C CHIP C CHIP C CHIP C
1000PF 0.10UF 1000PF 0.010UF 100PF
K K K K J
C652 C657 C662 C663 C670
CC73GCH1H101J CK73GB1E103K C92-0628-05 C92-0519-05 C92-0003-05
CHIP C CHIP C CHIP-TAN CHIP-TAN CHIP-TAN
100PF 0.010UF 10UF 1.0UF 0.47UF
J K 10WV 25WV 25WV
C769-771 C772 C773 C774 C775-779
C92-0560-05 C92-0633-05 C92-0514-05 CK73FB1C105K C92-0519-05
CHIP-TAN CHIP-TAN CHIP-TAN CHIP C CHIP-TAN
10UF 22UF 2.2UF 1.0UF 1.0UF
6.3WV 10WV 10WV K 25WV
C679,680 C681 C684 C685 C690
C92-0628-05 C92-0546-05 CC73GCH1H101J CK73GB1E103K CC73GCH1H101J
CHIP-TAN CHIP-TAN CHIP C CHIP C CHIP C
10UF 68UF 100PF 0.010UF 100PF
10WV 6.3WV J K J
C780-782 C783 C784 C785,786 C787
CK73FB1C105K CK73GB1H471K CK73FB1C105K CK73GB1C104K CK73FB1C105K
CHIP C CHIP C CHIP C CHIP C CHIP C
1.0UF 470PF 1.0UF 0.10UF 1.0UF
K K K K K
C691,692 C693,694 C695,696 C697-702 C703,704
CK73GB1E103K C92-0628-05 CK73GB1H471K C92-0628-05 CK73GB1C104K
CHIP C CHIP-TAN CHIP C CHIP-TAN CHIP C
0.010UF 10UF 470PF 10UF 0.10UF
K 10WV K 10WV K
C788 C789 C790 C791 C792-794
CC73GCH1H101J CE04EW1E331M CC73GCH1H101J CK73GB1H471K CK73GB1H102K
CHIP C ELECTRO CHIP C CHIP C CHIP C
100PF 330UF 100PF 470PF 1000PF
J 25WV J K K
C705 C706 C707-709 C710 C711
CK73GB1E103K C92-0628-05 CK73GB1E103K C92-0628-05 CK73GB1H471K
CHIP C CHIP-TAN CHIP C CHIP-TAN CHIP C
0.010UF 10UF 0.010UF 10UF 470PF
K 10WV K 10WV K
C795 C796,797 C798 C799 C800
CC73GCH1H101J CK73GB1H102K CE04EW1E470M CK73GB1H102K CE04EW1E470M
CHIP C CHIP C ELECTRO CHIP C ELECTRO
100PF 1000PF 47UF 1000PF 47UF
J K 25WV K 25WV
C712 C713,714 C715 C716,717 C718,719
CK73GB1E103K C92-0628-05 CK73GB1E103K CK73GB1H471K CK73GB1E103K
CHIP C CHIP-TAN CHIP C CHIP C CHIP C
0.010UF 10UF 0.010UF 470PF 0.010UF
K 10WV K K K
C801 C802-805 C806 C807-810 C811
C92-0560-05 CK73GB1H102K CE04EW1E470M CK73GB1H102K CE04EW1E470M
CHIP-TAN CHIP C ELECTRO CHIP C ELECTRO
10UF 1000PF 47UF 1000PF 47UF
6.3WV K 25WV K 25WV
C720-722 C723 C724 C725 C726
C92-0628-05 CK73FB1C105K CK73GB1H182K CC73GCH1H470J CC73GCH1H181J
CHIP-TAN CHIP C CHIP C CHIP C CHIP C
10UF 1.0UF 1800PF 47PF 180PF
10WV K K J J
C812,813 C814 C815 C816 C817
CK73GB1H102K C92-0777-05 CK73FB1E104K CK73GB1H102K CE04EW1E470M
CHIP C 1000PF ELECTROLYTIC CAP CHIP C 0.10UF CHIP C 1000PF ELECTRO 47UF
K
C727,728 C729 C730,731 C732 C733
CK73GB1E103K C92-0628-05 CK73GB1E103K CK73GB1H471K C92-0628-05
CHIP C CHIP-TAN CHIP C CHIP C CHIP-TAN
0.010UF 10UF 0.010UF 470PF 10UF
K 10WV K K 10WV
C818-820 C821,822 C823 C824 C825
CK73GB1H102K CC73GCH1H101J C92-0619-05 CK73GB1H472K CK73GB1C104K
CHIP C CHIP C CHIP-TAN CHIP C CHIP C
1000PF 100PF 47UF 4700PF 0.10UF
K J 4WV K K
C734 C735 C736 C737 C738
CC73GCH1H270J CC73GCH1H150J CK73GB1H182K CC73GCH1H270J CK73GB1E103K
CHIP C CHIP C CHIP C CHIP C CHIP C
27PF 15PF 1800PF 27PF 0.010UF
J J K J K
C826 C827 C828
C92-0560-05 C92-0633-05 C92-0514-05
CHIP-TAN CHIP-TAN CHIP-TAN
10UF 22UF 2.2UF
6.3WV 10WV 10WV
C739 C740 C741 C742 C743
CC73GCH1H181J CC73GCH1H101J CK73GB1E103K CK73GB1H471K CK73GB1E103K
CHIP C CHIP C CHIP C CHIP C CHIP C
180PF 100PF 0.010UF 470PF 0.010UF
J J K K K
CN1 CN2 CN3 CN4 CN14
E04-0154-05 E40-5538-05 E04-0154-05 E40-5538-05 E40-6009-05
PIN SOCKET PIN ASSY PIN SOCKET PIN ASSY FLAT CABLE CONNECTOR
C744-746 C747,748 C749 C750,751 C752
C92-0628-05 CK73GB1E103K CK73GB1H471K CK73GB1E103K CK73GB1H471K
CHIP-TAN CHIP C CHIP C CHIP C CHIP C
10UF 0.010UF 470PF 0.010UF 470PF
10WV K K K K
CN15 CN16 CN18,19 CN600 CN601
E40-5703-05 E40-5632-05 E04-0154-05 E40-6102-05 E40-5701-05
PIN ASSY PIN ASSY PIN SOCKET PIN ASSY PIN ASSY
E40-6009-05
FLAT CABLE CONNECTOR
CN602
✽
Destination
K K 25WV
31
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) Ref. No.
Address New parts
Parts No.
Destination
Description
CN603 CN604 CN605 CN606
E40-5887-05 E40-5702-05 E40-5704-05 E40-5960-05
PIN ASSY PIN ASSY PIN ASSY PIN ASSY
F1
F53-0217-05
FUSE
CF1 CF2 L1 L2 L2
L72-0366-05 L72-0376-05 L34-4616-05 L79-1771-05 L79-1772-05
CERAMIC FILTER CERAMIC FILTER AIR-CORE COIL HELICAL BLOCK HELICAL BLOCK
K,E K2
L40-1575-34 L40-1875-34 L79-1771-05 L79-1772-05 L40-1075-34
SMALL FIXED INDUCTOR (15NH) SMALL FIXED INDUCTOR (18NH) HELICAL BLOCK HELICAL BLOCK SMALL FIXED INDUCTOR (10NH)
K2 K,E K,E K2 K2
L10 L11 L12 L13 L14
L40-1581-37 L40-1885-34 L40-3381-37 L40-1005-34 L34-4527-05
SMALL FIXED INDUCTOR (0.150UH) SMALL FIXED INDUCTOR (180NH) SMALL FIXED INDUCTOR (0.330UH) SMALL FIXED INDUCTOR (10UH) COIL
L15 L16 L17,18 L19 L20
L34-4526-05 L34-4527-05 L34-4526-05 L34-4527-05 L40-1095-34
COIL COIL COIL COIL SMALL FIXED INDUCTOR (1UH)
L21 L23 L24 L25 L26
L40-1005-34 L40-1095-34 L34-4530-05 L40-2775-34 L40-1575-34
SMALL FIXED INDUCTOR (10UH) SMALL FIXED INDUCTOR (1UH) COIL SMALL FIXED INDUCTOR (27NH) SMALL FIXED INDUCTOR (15NH)
L27 L27,28 L28 L29,30 L31,32
L40-2275-34 L40-1875-34 L40-1875-34 L40-1875-92 L40-1005-34
SMALL FIXED INDUCTOR (22NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (10UH)
L33 L34 L35-39 L40 L41
L40-1575-92 L40-1005-34 L92-0140-05 L92-0158-05 L92-0140-05
SMALL FIXED INDUCTOR (15NH) SMALL FIXED INDUCTOR (10UH) FERRITE CHIP FERRITE CHIP FERRITE CHIP
L42 L600-613 X1 X2,3 X600
L40-6865-92 L92-0140-05 L77-1762-05 L77-1849-05 L78-0431-05
SMALL FIXED INDUCTOR (6.8NH) FERRITE CHIP CRYSTAL RESONATOR (44.395MHZ) VCXO (16.8MHZ) RESONATOR (14.7456M)
X601 XF1 XF2
L77-1799-05 L71-0513-05 L71-0512-05
CRYSTAL RESONATOR (16.515MHZ) MCF (44.85MHZ NARR) MCF (44.85MHZ WIDE)
CP600,601 CP602 CP603 CP604,605 CP606
R90-0725-05 R90-0724-05 R90-1019-05 R90-0725-05 R90-0719-05
MULTI-COMP MULTI-COMP MULTI-COMP MULTI-COMP MULTI-COMP
1K X2 1K X4 100 X2 1K X2 4.7K X2
CP607,608 CP609 CP610,611 CP612-614 CP615-619
R90-0725-05 R90-1019-05 R90-0750-05 R90-0725-05 R90-0750-05
MULTI-COMP MULTI-COMP MULTIPLE RESISTOR MULTI-COMP MULTIPLE RESISTOR
1K X2 100 X2
L3 L3 L4,5 L4,5 L6
32
✽ ✽
✽ ✽
✽
1K X2
K,E K2 K,E
Ref. No.
New Address parts
Parts No.
Destination
Description
R1 R2 R3 R5 R8
R92-0670-05 RK73GB1J122J RK73GB1J102J RK73GB1J101J RK73GB1J151J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 1.2K 1.0K 100 150
J J J J
1/16W 1/16W 1/16W 1/16W
K,E
R9 R10 R11 R13 R14
RK73GB1J223J RK73GB1J180J RK73GB1J271J RK73GB1J271J RK73GB1J333J
CHIP R CHIP R CHIP R CHIP R CHIP R
22K 18 270 270 33K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R17 R18 R19 R20 R30
RK73GB1J824J RK73GB1J684J RK73GB1J474J RK73GB1J224J RK73GB1J821J
CHIP R CHIP R CHIP R CHIP R CHIP R
820K 680K 470K 220K 820
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R31 R32 R33 R34 R35
RK73GB1J5R6J RK73GB1J821J RK73GB1J470J RK73GB1J102J RK73GB1J182J
CHIP R CHIP R CHIP R CHIP R CHIP R
5.6 820 47 1.0K 1.8K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R36 R37 R38 R39 R40
RK73GB1J102J RK73GB1J682J R92-1252-05 RK73GB1J560J RK73GB1J270J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 6.8K 0 OHM 56 27
J J
1/16W 1/16W
J J
1/16W 1/16W
R41 R42-45 R46 R47 R48
RK73GB1J222J RK73GB1J223J RK73GB1J222J RK73GB1J153J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
2.2K 22K 2.2K 15K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R49 R50 R51 R52 R53
RK73GB1J221J RK73GB1J153J R92-1252-05 RK73GB1J223J RK73GB1J682J
CHIP R CHIP R CHIP R CHIP R CHIP R
220 15K 0 OHM 22K 6.8K
J J
1/16W 1/16W
J J
1/16W 1/16W
R54 R55 R56 R57 R58
RK73GB1J102J RK73GB1J223J RK73GB1J682J RK73GB1J182J RK73GB1J153J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 22K 6.8K 1.8K 15K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R59 R60 R61 R62 R63
RK73GB1J223J RK73GB1J103J RK73GB1J274J RK73GB1J222J RK73GB1J183J
CHIP R CHIP R CHIP R CHIP R CHIP R
22K 10K 270K 2.2K 18K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R64 R65 R66 R67 R68
RK73GB1J220J RK73GB1J472J RK73GB1J334J RK73GB1J102J RK73GB1J332J
CHIP R CHIP R CHIP R CHIP R CHIP R
22 4.7K 330K 1.0K 3.3K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R69 R71 R72 R73 R74,75
RK73GB1J392J RK73GB1J104J RK73GB1J393J RK73GB1J474J RK73GB1J220J
CHIP R CHIP R CHIP R CHIP R CHIP R
3.9K 100K 39K 470K 22
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R76 R77,78 R79 R82 R83
RK73GB1J104J RK73GB1J473J RK73GB1J104J RK73GB1J474J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
100K 47K 100K 470K 0 OHM
J J J J
1/16W 1/16W 1/16W 1/16W
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) Ref. No.
New Address parts
Parts No.
Destination
Description
Ref. No.
New Address parts
Parts No.
Destination
Description
R625-628 R629 R630,631 R633,634 R635,636
RK73GB1J102J R92-1252-05 RK73GB1J473J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 0 OHM 47K 47K 1.0K
R637 R638 R639 R640 R641
R92-1252-05 RK73GB1J102J R92-1252-05 RK73GB1J102J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 1.0K J 0 OHM 1.0K J 0 OHM
1/16W 1/16W 1/16W 1/16W 1/16W
R642 R643 R644 R645,646 R647-652
RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 47K 1.0K 47K 1.0K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
J J
1/16W 1/16W
J J
1/16W 1/16W
R653,654 R655 R656 R657-661 R662
R92-0670-05 RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 47K 1.0K 47K 1.0K
J J J J
1/16W 1/16W 1/16W 1/16W
J
1/16W
J J J
1/16W 1/16W 1/16W
R663-667 R668 R669-671 R672-674 R675
RK73GB1J473J RK73GB1J183J RK73GB1J223J RK73GB1J104J RK73GB1J333J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 18K 22K 100K 33K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
10 4.7K 47K 1.0K 10K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R676 R678 R679,680 R681 R682
RK73GB1J823J RK73GB1J104J RK73GB1J223J RK73GB1J183J RK73GB1J153J
CHIP R CHIP R CHIP R CHIP R CHIP R
82K 100K 22K 18K 15K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
CHIP R CHIP R CHIP R CHIP R CHIP R
820 5.6 820 1.0K 0 OHM
J J J J
1/16W 1/16W 1/16W 1/16W
R683 R684 R685,686 R687 R688-690
RK73GB1J124J RK73GB1J473J RK73GB1J104J RK73GB1J223J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
120K 47K 100K 22K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
RK73GB1J102J RK73GB1J472J RK73FB2A470J RK73GB1J472J RK73GB1J180J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 4.7K 47 4.7K 18
J J J J J
1/16W 1/16W 1/10W 1/16W 1/16W
R691-693 R694,695 R696 R697 R698
R92-1252-05 RK73GB1J101J RK73GB1J103J RK73GB1J101J RK73GB1J103J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 100 10K 100 10K
J J J J
1/16W 1/16W 1/16W 1/16W
R151-158 R160,161 R162-164 R165 R166
RK73GB1J102J RK73GB1J471J RK73GB1J271J RK73GB1J471J RK73GB1J223J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 470 270 470 22K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R699 R700 R701 R702 R703
R92-1252-05 RK73GB1J101J R92-1252-05 RK73GB1J473J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 100 J 0 OHM 47K J 0 OHM
R600 R601 R602 R603 R604
RK73GB1J473J R92-0670-05 RK73GB1J472J RK73GB1J102J RK73GB1J333J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 0 OHM 4.7K 1.0K 33K
J
1/16W
J J J
1/16W 1/16W 1/16W
R704-706 R707-709 R710 R712 R713
RK73GB1J473J RK73GB1J223J RK73GB1J473J RK73GB1J473J RK73GB1J273J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 22K 47K 47K 27K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R605 R606 R607-613 R614 R615
RK73GB1J104J RK73GB1J473J R92-1252-05 RK73GB1J473J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
100K J 47K J 0 OHM 47K J 0 OHM
1/16W 1/16W
R714 R715 R717,718 R719 R720
RK73GB1J223J RK73GB1J103J RK73GB1J473J RK73GB1J104J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
22K 10K 47K 100K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R616 R618 R619 R620-622 R623,624
RK73GB1J473J R92-1252-05 RK73GB1J473J RK73GB1J102J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
47K J 0 OHM 47K J 1.0K J 0 OHM
1/16W
R721 R722 R723,724 R726 R727
RK73GB1J223J RK73GB1J334J R92-1252-05 RK73GB1J473J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
22K J 330K J 0 OHM 47K J 0 OHM
1/16W 1/16W
R87,88 R90 R91 R92 R93
RK73GB1J102J R92-1252-05 RK73GB1J472J RK73GB1J182J RK73GB1J101J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 0 OHM 4.7K 1.8K 100
J
1/16W
J J J
1/16W 1/16W 1/16W
R93,94 R94 R95 R96 R97
RK73GB1J101J RK73GB1J820J RK73GB1J472J RK73GB1J182J RK73GB1J332J
CHIP R CHIP R CHIP R CHIP R CHIP R
100 82 4.7K 1.8K 3.3K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R98 R99 R100 R101 R102
RK73GB1J102J RK73GB1J101J RK73GB1J680J RK73GB1J470J RK73GB1J332J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 100 68 47 3.3K
J J J J J
R103 R105 R106 R107 R109
RK73GB1J102J RK73GB1J270J R92-1252-05 RK73GB1J470J RK73GB1J101J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 27 0 OHM 47 100
R113 R114 R120,121 R122,123 R124,125
RK73GB1J471J R92-1252-05 RK73GB1J152J RK73GB1J100J RK73GB1J152J
CHIP R CHIP R CHIP R CHIP R CHIP R
470 0 OHM 1.5K 10 1.5K
R126,127 R128 R129,130 R131 R133
RK73GB1J100J RK73GB1J472J RK73GB1J473J RK73GB1J102J RK73GB1J103J
CHIP R CHIP R CHIP R CHIP R CHIP R
R134 R135 R136 R137,138 R139-142
RK73GB1J821J RK73GB1J5R6J RK73GB1J821J RK73GB1J102J R92-1252-05
R143 R144 R145 R148 R150
1/16W
1/16W 1/16W
K2 K,E K2
J
1/16W
J J J
1/16W 1/16W 1/16W
1/16W 1/16W
1/16W 1/16W
1/16W
33
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) Ref. No.
Address New parts
Parts No.
Destination
Description
Ref. No.
New Address parts
Parts No.
Destination
Description
R728,729 R730 R731 R732 R733
RK73GB1J223J RK73GB1J101J RK73GB1J472J RK73GB1J473J R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
22K 100 4.7K 47K 0 OHM
J J J J
1/16W 1/16W 1/16W 1/16W
R802 R803 R804 R805 R806
RK73FB2A2R2J RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
2.2 47K 1.0K 47K 1.0K
J J J J J
1/10W 1/16W 1/16W 1/16W 1/16W
R734 R735 R736,737 R738 R739
RK73GB1J473J RK73GB1J333J RK73GB1J473J RK73GB1J274J RK73GB1J103J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 33K 47K 270K 10K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R807 R808 R809 R810 R811
RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 1.0K 47K 1.0K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R740 R741 R742 R743 R744
RK73GB1J104J RK73GB1J154J R92-0670-05 RK73GB1J473J RK73GB1J393J
CHIP R CHIP R CHIP R CHIP R CHIP R
100K 150K 0 OHM 47K 39K
J J
1/16W 1/16W
R812 R813,814 R815
RK73GB1J223J RK73GB1J473J RK73GB1J104J
CHIP R CHIP R CHIP R
22K 47K 100K
J J J
1/16W 1/16W 1/16W
J J
1/16W 1/16W
K1
S76-0401-05
RELAY
R745 R747 R749-752 R753,754 R755,756
RK73GB1J473J RK73GB1J103J R92-1252-05 RK73GB1J473J R92-0670-05
CHIP R CHIP R CHIP R CHIP R CHIP R
47K J 10K J 0 OHM 47K J 0 OHM
1/16W 1/16W
D1-4 D5 D7 D8 D9
DAN235K MA742 1SS355 DAN235K HSM88AS
DIODE DIODE DIODE DIODE DIODE
R758 R760 R762 R763 R764,765
RK73GB1J103J RK73GB1J122J RK73GB1J472J RK73GB1J103J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
10K 1.2K 4.7K 10K 1.0K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
D11 D12 D600 D601 D606-625
02DZ5.1(Y) 02DZ18(X,Y) DA204U MA2S111 DA204U
ZENER DIODE ZENER DIODE DIODE DIODE DIODE
R766 R767 R768 R769,770 R771
RK73GB1J122J RK73GB1J473J RK73GB1J122J R92-0670-05 RK73GB1J122J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.2K 47K 1.2K 0 OHM 1.2K
J J J
1/16W 1/16W 1/16W
J
1/16W
D626 D627,628 D629 IC1,2 IC3
MINISMDE190 1SS355 DA204U NJM4558E NJM78L05UA
VARISTOR DIODE DIODE MOS IC BI-POLAR IC
R772 R773 R774 R775 R776
RK73GB1J473J RK73GB1J102J RK73GB1J105J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 1.0K 1.0M 47K 1.0K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC4 IC5 IC6 IC7 IC9
NJM7808FA AN8009M M62354GP BU4094BCF TK14489V
BI-POLAR IC MOS IC MOS IC MOS IC BI-POLAR IC
R777 R778 R779 R780 R781
RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J471J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 1.0K 47K 1.0K 470
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC10 IC11 IC600 IC601 IC602
TA7808F NJM78L05UA AT2408N10SI2.5 RH5VL42C BU4094BCFV
ANALOG IC BI-POLAR IC ROM IC MOS IC MOS IC
R782 R783 R784 R785 R786
RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 1.0K 47K 1.0K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC603 IC604 IC605 IC606 IC607
TC74LVX4245FS 30622M4-113GP BU4053BCF TC74LVX4245FS NJM4558E
MOS IC MPU MOS IC MOS IC MOS IC
R787 R788 R789 R790 R791
RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 47K 1.0K 47K 1.0K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC608 IC609 IC610 IC611 IC612
TA75S01F AT29C020-90TI TA75S01F NJM4558E TC7S04FU
MOS IC ROM IC MOS IC MOS IC MOS IC
R792 R793 R794 R795 R796
RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J
CHIP R CHIP R CHIP R CHIP R CHIP R
47K 1.0K 47K 1.0K 47K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC613 IC614 IC615 IC616,617 IC618
TC74VHC4040FT AK4550VT M62364FP NJM4558E 320VC5402PGE
MOS IC MOS IC MOS IC MOS IC MPU
R797 R798 R799 R800 R801
RK73GB1J102J RK73GB1J473J RK73GB1J102J RK73GB1J473J RK73GB1J102J
CHIP R CHIP R CHIP R CHIP R CHIP R
1.0K 47K 1.0K 47K 1.0K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
IC619 IC620 IC621 IC622 IC623
TC75W51FU ADM202EARN TC7S00FU TC7S66FU BU4094BCFV
MOS IC MOS IC MOS IC MOS IC MOS IC
34
1/16W
✽
✽
✽
TKR-850 PARTS LIST TX-RX UNIT (X57-6270-XX) RX PLL/VCO (X58-4800-XX) Ref. No.
New Address parts
Parts No.
Description
Destination
Ref. No.
New Address parts
Parts No.
Destination
Description
XC62FP1802P XC62FP3302P TA78L05F LA4422 TA78L05F
MOS IC MOS IC MOS IC BI-POLAR IC MOS IC
C355 C356 C357 C358,359 C360,361
CC73GCH1H050B CC73GCH1H060B CK73GB1H471K CC73GCH1H1R5B CK73FB1E104K
CHIP C CHIP C CHIP C CHIP C CHIP C
5.0PF 6.0PF 470PF 1.5PF 0.10UF
B B K B K
Q1,2 Q3 Q4 Q5 Q6
2SC3357 2SC3356(R24) DTC144EUA DTA144EUA DTC144EUA
TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR
C362 C363 C363 C364,365 C366-369
CC73GCH1H220G CC73GCH1H150G CC73GCH1H180G CK73GB1H471K CC73GCH1H070B
CHIP C CHIP C CHIP C CHIP C CHIP C
22PF 15PF 18PF 470PF 7.0PF
G G G K B
Q7 Q8,9 Q10 Q11 Q12-15
2SC4617(S) 2SC3356 2SC3357 2SC3356(R24) 2SC4116(GR)
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
C370,371 C372,373 C374,375 C376-378 C379
CC73GCH1H100C CK73GB1H471K CC73GCH1H0R5B CK73GB1H471K CC73GCH1H040C
CHIP C CHIP C CHIP C CHIP C CHIP C
10PF 470PF 0.5PF 470PF 4.0PF
C K B K C
Q16 Q17 Q18 Q19,20 Q23
2SB1132(Q,R) DTC114EUA 2SB1386(R) DTC114EUA DTC114EUA
TRANSISTOR DIGITAL TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR
C383 C386 C386 TC350,351
✽
CK73GB1H471K CC73GCH1H101J CC73GCH1H220J C05-0396-05
CHIP C 470PF K CHIP C 100PF J CHIP C 22PF J CERAMIC TRIMMER CAP (8P)
Q24 Q25 Q600 Q601 Q602
DTD114EK DTC114EUA 2SK1824 DTC114EUA 2SK1824
DIGITAL TRANSISTOR DIGITAL TRANSISTOR FET DIGITAL TRANSISTOR FET
CN300 CN350 CN351
✽
E40-5699-05 E40-5755-05 E40-6098-05
PIN ASSY PIN ASSY PIN ASSY
-
✽
F10-2377-04
SHIELDING CASE
Q603 Q604 Q605 Q606 Q609
DTC114EUA 2SK1824 DTC114EUA DTC363EK DTC114EUA
DIGITAL TRANSISTOR FET DIGITAL TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR
L92-0148-05 L40-1575-34 L40-1875-34 L40-1875-34 L40-2275-34
FERRITE CHIP SMALL FIXED INDUCTOR (15NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (22NH)
Q610 Q611 TH1
2SJ506(S) DTC114EUA 157-503-53006
FET DIGITAL TRANSISTOR THERMISTOR
L40-1095-34 L34-4607-05 L34-4608-05 L40-1595-34 L40-2775-34
SMALL FIXED INDUCTOR (1UH) AIR-CORE COIL AIR-CORE COIL SMALL FIXED INDUCTOR (1.5UH) SMALL FIXED INDUCTOR (27NH)
A1
W02-1939-05
DBM L362
L40-3371-34
SMALL FIXED INDUCTOR (33NH)
R300 R301-304 R305 R306 R308
RK73GB1J100J RK73GB1J101J R92-1252-05 RK73GB1J220J RK73GB1J560J
CHIP R CHIP R CHIP R CHIP R CHIP R
10 100 0 OHM 22 56
J J
1/16W 1/16W
J J
1/16W 1/16W
R309 R309 R310 R311 R312
RK73GB1J331J RK73GB1J391J RK73GB1J332J RK73GB1J103J RK73GB1J331J
CHIP R CHIP R CHIP R CHIP R CHIP R
330 390 3.3K 10K 330
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
K,E K2
R312 R313 R314 R315 R316
RK73GB1J391J RK73GB1J222J RK73GB1J474J RK73GB1J151J RK73FB2A152J
CHIP R CHIP R CHIP R CHIP R CHIP R
390 2.2K 470K 150 1.5K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/10W
K2
R317,318 R319 R320 R321 R322
R92-1252-05 RK73GB1J330J RK73GB1J222J RK73GB1J273J RK73GB1J103J
CHIP R CHIP R CHIP R CHIP R CHIP R
0 OHM 33 2.2K 27K 10K
J J J J
1/16W 1/16W 1/16W 1/16W
R350-353 R354,355 R356 R356
R92-1252-05 RK73GB1J330J RK73GB1J181J RK73GB1J221J
CHIP R CHIP R CHIP R CHIP R
0 OHM 33 J 180 J 220 J
1/16W 1/16W 1/16W
IC624 IC625,626 IC627,628 IC629 IC630
3B
RX PLL/VCO (X58-4800-XX)
L300 L301,302 L301,302 L303 L303 L350-355 L356,357 L356,357 L358-361 L362
-10 : K,E -11 : K2
C304,305 C306 C307 C308-310 C311
CK73GB1H102K CK73GB1H103K CK73GB1H471K CK73FB1E104K C92-0001-05
CHIP C CHIP C CHIP C CHIP C CHIP C
1000PF 0.010UF 470PF 0.10UF 0.1UF
K K K K 35WV
C312 C312 C314 C314 C315
CC73GCH1H060D CC73GCH1H070D CC73GCH1H120J CC73GCH1H150J CK73FB1H473K
CHIP C CHIP C CHIP C CHIP C CHIP C
6.0PF 7.0PF 12PF 15PF 0.047UF
D D J J K
K2 K,E K,E K2
C317 C317 C318 C319 C320
CC73GCH1H060D CC73GCH1H070D C92-0514-05 CK73GB1H471K C92-0514-05
CHIP C CHIP C CHIP-TAN CHIP C CHIP-TAN
6.0PF 7.0PF 2.2UF 470PF 2.2UF
D D 10WV K 10WV
K2 K,E
C321 C322 C323 C324 C325
CC73GCH1H040C CK73GB1H471K CK73FB1E224K C92-0002-05 CC73GCH1H040C
CHIP C CHIP C CHIP C CHIP-TAN CHIP C
4.0PF 470PF 0.22UF 0.22UF 4.0PF
C K K 35WV C
C350,351 C354
CK73GB1H471K CK73GB1H471K
CHIP C CHIP C
470PF 470PF
K K
✽ ✽
K,E K2
K,E K2
K2 K,E K2 K,E
K2 K,E K2 K,E
K,E
K2 K,E
35
TKR-850 PARTS LIST RX PLL/VCO (X58-4800-XX) TX PLL/VCO (X58-4810-XX) Ref. No.
Address New parts
Parts No.
Destination
Description
R357 R357 R358,359 R360-363 R364
RK73GB1J151J RK73GB1J181J RK73GB1J470J RK73GB1J472J RK73GB1J103J
CHIP R CHIP R CHIP R CHIP R CHIP R
150 180 47 4.7K 10K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R365 R366 R367 R368
RK73GB1J333J RK73GB1J103J RK73GB1J101J RK73GB1J330J
CHIP R CHIP R CHIP R CHIP R
33K 10K 100 33
J J J J
1/16W 1/16W 1/16W 1/16W
D350-353 IC300 Q300,301 Q302 Q350,351
1SV282 SA7025DK 2SC4116(GR) 2SC4226(R24) 2SK508NV(K52)
VARIABLE CAPACITANCE DIODE MOS IC TRANSISTOR TRANSISTOR FET
Q352,353 Q354 Q355
2SC4116(Y) DTC114EUA 2SC4226(R24)
TRANSISTOR DIGITAL TRANSISTOR TRANSISTOR
TX PLL/VCO (X58-4810-XX)
K2 K,E
-10 : K,E -11 : K2
Ref. No.
New Address parts
Parts No.
Destination
Description
CN351
✽
E40-6098-05
PIN ASSY
-
✽
F10-2377-04
SHIELDING CASE
L300 L301,302 L303 L303 L352-354
L92-0148-05 L40-1575-34 L40-1875-34 L40-2275-34 L40-1095-34
FERRITE CHIP SMALL FIXED INDUCTOR (15NH) SMALL FIXED INDUCTOR (18NH) SMALL FIXED INDUCTOR (22NH) SMALL FIXED INDUCTOR (1UH)
L356 L356 L358 L360 L362
L34-4605-05 L34-4645-05 L40-1095-34 L40-1095-34 L40-2275-34
AIR-CORE COIL AIR-CORE COIL SMALL FIXED INDUCTOR (1UH) SMALL FIXED INDUCTOR (1UH) SMALL FIXED INDUCTOR (22NH)
K2 K,E
L362
L40-3371-34
SMALL FIXED INDUCTOR (33NH)
K,E
R300 R301-304 R305 R306 R308
RK73GB1J100J RK73GB1J101J R92-1252-05 RK73GB1J220J RK73GB1J560J
CHIP R CHIP R CHIP R CHIP R CHIP R
10 100 0 OHM 22 56
J J
1/16W 1/16W
J J
1/16W 1/16W
R309 R310 R311 R312 R313
RK73GB1J331J RK73GB1J332J RK73GB1J103J RK73GB1J331J RK73GB1J222J
CHIP R CHIP R CHIP R CHIP R CHIP R
330 3.3K 10K 330 2.2K
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
R314 R315 R316 R317,318 R319
RK73GB1J474J RK73GB1J151J RK73FB2A152J R92-1252-05 RK73GB1J330J
CHIP R CHIP R CHIP R CHIP R CHIP R
470K 150 1.5K 0 OHM 33
J J J
1/16W 1/16W 1/10W
J
1/16W
R320 R321 R322 R351 R353
RK73GB1J222J RK73GB1J273J RK73GB1J103J R92-1252-05 R92-1252-05
CHIP R CHIP R CHIP R CHIP R CHIP R
2.2K J 27K J 10K J 0 OHM 0 OHM
1/16W 1/16W 1/16W
C304,305 C306 C307 C308-310 C311
CK73GB1H102K CK73GB1H103K CK73GB1H471K CK73FB1E104K C92-0001-05
CHIP C CHIP C CHIP C CHIP C CHIP C
1000PF 0.010UF 470PF 0.10UF 0.1UF
K K K K 35WV
C312 C312 C314 C314 C315
CC73GCH1H050C CC73GCH1H060D CC73GCH1H100D CC73GCH1H120J CK73FB1H473K
CHIP C CHIP C CHIP C CHIP C CHIP C
5.0PF 6.0PF 10PF 12PF 0.047UF
C D D J K
K2 K,E K2 K,E
C317 C317 C318 C319 C320
CC73GCH1H050C CC73GCH1H060D C92-0514-05 CK73GB1H471K C92-0514-05
CHIP C CHIP C CHIP-TAN CHIP C CHIP-TAN
5.0PF 6.0PF 2.2UF 470PF 2.2UF
C D 10WV K 10WV
K2 K,E
C321 C322 C323 C324 C325
CC73GCH1H040C CK73GB1H471K CK73FB1E224K C92-0002-05 CC73GCH1H040C
CHIP C CHIP C CHIP C CHIP-TAN CHIP C
4.0PF 470PF 0.22UF 0.22UF 4.0PF
C K K 35WV C
R354 R359 R365 R366 R367
RK73GB1J330J RK73GB1J470J RK73GB1J333J RK73GB1J103J RK73GB1J820J
CHIP R CHIP R CHIP R CHIP R CHIP R
33 47 33K 10K 82
J J J J J
1/16W 1/16W 1/16W 1/16W 1/16W
C350,351 C354 C356 C356 C359
CK73GB1H471K CK73GB1H471K CC73GCH1H070B CC73GCH1H080B CC73GCH1H1R5B
CHIP C CHIP C CHIP C CHIP C CHIP C
470PF 470PF 7.0PF 8.0PF 1.5PF
K K B B B
R368 R372,373 R376
RK73GB1J330J RK73GB1J104J RK73GB1J151J
CHIP R CHIP R CHIP R
33 100K 150
J J J
1/16W 1/16W 1/16W
C360 C362 C364 C366 C368
CK73FB1E104K CC73GCH1H120G CK73GB1H471K CC73GCH1H070B CC73GCH1H070B
CHIP C CHIP C CHIP C CHIP C CHIP C
0.10UF 12PF 470PF 7.0PF 7.0PF
K G K B B
D350 D352 D354 IC300 Q300,301
1SV282 1SV282 1SV214 SA7025DK 2SC4116(GR)
VARIABLE CAPACITANCE DIODE VARIABLE CAPACITANCE DIODE VARIABLE CAPACITANCE DIODE MOS IC TRANSISTOR
C370 C374 C377,378 C379 C380
CC73GCH1H070B CC73GCH1H0R5B CK73GB1H471K CC73GCH1H040C CC73GCH1H0R5B
CHIP C CHIP C CHIP C CHIP C CHIP C
7.0PF 0.5PF 470PF 4.0PF 0.5PF
B B K C B
Q302 Q350 Q355
2SC4226(R24) 2SK508NV(K52) 2SC4226(R24)
TRANSISTOR FET TRANSISTOR
CC73GCH1H471J C05-0396-05
CHIP C 470PF J CERAMIC TRIMMER CAP (8P)
E40-5699-05 E40-5755-05
PIN ASSY PIN ASSY
C382,383 TC350 CN300 CN350
36
✽
K2 K,E
K2 K,E
K2
TKR-850
TKR-850
EXPLODED VIEW A
1
A B C D E F G H J L N M O P Q
C
B
ø3 (FW) M2.6 x 6 M4 x 6 M4 x 14 M4 x 20 BLK M3 x 6 (F) M4 x 8 (F) BLK M3 x 6 (OC) BLK M3 x 14 (Bi) M3 x 8 M4 x 6 (Bi) BLK M2.6 x 6 (Br-Tap) M3 x 5 (Br-Tap) BLK M3 x 6 (Br-Tap) BLK
: N09-2292-05 : N15-1030-46 : N30-2606-46 : N30-4006-46 : N30-4014-46 : N30-4020-45 : N32-3006-46 : N32-4008-45 : N33-3006-45 : N35-3014-46 : N67-3008-46 : N35-4006-45 : N87-2606-46 : N87-3005-45 : N87-3006-45
D
3 Mx14
2
4
Jx6
Jx6
30
702
21
27 44
42
20 26 28
701 Gx2
Nx3
Qx11
15 Cx2
38
Ox4 Fx4
G
Qx10
Ax2
700
36x2 Final (A/2)
TX-RX (A/2)
Dx3
48
Ox2 Cx2
14 1
37
Final (B/2)
Lx2
22
Bx2 34
G
2
12 Ex3
Ex3
47
29
16 705
703
Gx2
704
Qx6
Dx3
TX-RX (B/2)
33 47
24
IC629
23
Px4
69
Nx2
12
Hx3
Qx3 Hx3
704
Qx5 3
46 67
Display (A/2)
706
Display (B/2)
48x2
66 65
5
Parts with the exploded numbers larger than 700 are not supplied.
6 38
TKR-850 PACKING E 53 59 60 62 D K
F
Protection bag (H25-0029-04) Foot (J02-0475-05) x 2 Foot (J02-0492-04) x 2 Grommet (J59-0302-05) x 2 Binding head machine screw (N30-4006-46) x 2 Binding head machine screw (N35-3006-45) x 5
49 Cushion (G13-1801-04) 50 Cushion (G13-1802-04) 54 Protetion bag (H25-0747-04) 61 Hardware fixture (J21-8402-04) 707 Pamphlet : E 708 Warranty card : K,K2 11 Instruction manual (B62-1327-10)
1
64 Handle (K01-0418-15) 17 DC cord (E30-3427-15) 55 Protection bag (H25-0762-04)
8 Front glass (B10-2635-04) 10 Filter (B11-1259-04) 56 Protection bag (H25-2328-04)
18 Lead wire with connector (E31-3228-05) 36 Fuse (Blade, 15A/32V) (F05-1537-05) 53 Protection bag (H25-0029-04)
710 Packing fixture
709 Carton board
712 Protection bag
2 BA CK
UP
713 Packing fixture 711 Packing fixture
3
Parts with the exploded numbers larger than 700 are not supplied.
57 Item carton case (H52-1779-02)
39
TKR-850 ADJUSTMENT Test Equipment Required for Alignment Test Equipment 1. Standard Signal Generator (SSG) 2. Power Meter
3. Deviation Meter 4. Digital Volt Meter (DVM) 5. Oscilloscope 6. High Sensitivity Frequency Counter 7. Ammeter 8. AF Volt Meter (AF VTVM) 9. Audio Generator (AG)
Major Specifications 440 to 512MHz Frequency modulation and external modulation 0.1µV to greater than 1mV 50Ω 440 to 512MHz or more Vicinity of 50W 440 to 512MHz 1 to 20V DC High input impedance for minimum circuit loading DC through 30MHz 10Hz to 600MHz 0.2ppm or less 13A or more 50Hz to 10kHz 3mV to 3V 50Hz to 5kHz 0 to 1V 3% or less at 1kHz 50mV to 10Vrms 10 to 1.5V DC or less 50kΩ/V or greater Approx. 4Ω, 5W
Frequency Range Modulation Output Input Impedance Operation Frequency Measurement Capability Frequency Range Measuring Range Accuracy Frequency Range Frequency Stability Frequency Range Voltage Range Frequency Range Output Capability Input Level Measuring Range Input Impedance
10. Distortion Meter 11. Voltmeter 12. 4Ω Dummy Load
The following parts are required for adjustment • Test cable for local microphone
8
1
• The following test cables are recommended.
1 : NC 2 : +B 3 : GND 4 : PTT/TXD1 (PC serial data from radio) 5 : MIC GND 6 : MIC 7 : HOOK/RXD1 (PC serial data to radio) 8 : NC
Plug cord Part No. E30-3360-08
8pin HOOK (BRN)
MIC connector (Front panel view)
To AG AF VTVM
MIC (WHT) MICG
PTT (YEL) PTT SW
Cut
Test Channel (Default) No.
40
K
E
K2
PTT (RED)
8pin
RX
TX
RX
TX
RX
TX
1
450.10
450.00
440.10
440.00
480.10
480.00
2
465.10
465.00
455.10
455.00
496.10
496.00
3
479.90
480.00
469.90
470.00
511.90
512.00
4
455.10
455.00
445.10
445.00
485.10
485.00
5
460.10
460.00
450.10
450.00
490.10
490.00
6
470.10
470.00
460.10
460.00
500.10
500.00
7
475.10
475.00
465.10
465.00
505.10
505.00
8
462.60
462.50
452.60
452.50
493.60
493.50
9
467.60
467.50
457.60
457.50
498.60
498.50
10
440.10
440.00
459.90
460.00
499.90
500.00
11
459.90
460.00
479.90
480.00
519.90
520.00
Test cable for microphone input To connect the TX-RX unit A/2 (CN14) to the TX-RX unit B/2 (CN602) while in servicing, you can use the 36-pin flat cable, E37-0979-05, which is available from the KENWOOD parts center.
Flat cable (36-pin) about 256mm
TKR-850 ADJUSTMENT Measurement Item
Condition
Testequipment
Unit
Terminal
Adjustment Unit
Parts
Method
Specifications/Remarks
1. Setting & Firmware writing
1) Connect the unit to a suitable DC power supply. 2) Turn the DC source switch on after connecting a PC and FPU cable to the radio. → “P.G.” appears on LED display 3) Write the firmware to radio. After the end of firmware writing. → Red (TX) LED lights up
2. Write test frequency
1) Connect the unit to a suitable DC power supply. 2) Turn the DC source switch on after connecting a PC and FPU cable to the radio. → “E1” appears on LED display 3) Write the test and shipping frequency to the radio. → Green (BUSY) LED lights up 4) End of test frequency writing.
3. Setting
1) Connect the unit to a suitable DC power supply. 2) Turn the power switch on after connecting a PC and FPU cable to the radio. 3) Start up the program for the adjustment.
4. RX PLL lock voltage
1) RX VCO A high CH : 11 K CH : 10 K2,E
5. TX PLL lock voltage
DVM
TX-RX (A/2)
RX-CV
RX VCO TC350 1.50V (A3)
2) RX VCO A low CH : 10 K CH : 1 K2,E
Check
3) RX VCO B high CH : 3 K,K2 CH : 11 E
RX VCO TC351 1.50V (A3)
4) RX VCO B low CH : 11 K CH : 10 K2,E
Check
1) TX VCO high CH : 3
TX-CV
TX VCO TC350 1.50V (A2)
2) TX VCO low CH : 1
Check
± 0.1V
8V or less
± 0.1V
8V or less
± 0.1V
8V or less
6. RX frequency
1) Connect the frequency f. counter CN3 PC adj. 50Hz or less counter to CN3, then Test CH–44.85MHz measure the frequency CH : 2 Note : RX frequency means the local frequency of the RX VCO. So its frequency is wanted frequency minus the IF frequency. 7. Setting
1) Remove 8 pin cable and the coaxial cable from CN16, and CN19 on TX-RX side.
8. TX frequency
1) Connect the frequency counter to CN19, then measure the frequency CH : 2
9. Setting
1) Insert 8 pin cable and the coaxial cable to CN16, and CN19 on TX-RX side.
10. Maximum power limitting
1) Measure the RF power at TX ANT. High CH
13. TX RF high power
1) Measure the RF power at TX ANT. Low CH 2) Center CH 3) High CH
f. counter TX-RX (A/2)
Power meter Rear
CN19
TX ANT
PC adj.
Final
VR1
50Hz or less
Adjust the RF power ± 1W to 43W.
PC adj. 40W (Shipping power)
± 1W
41
TKR-850 ADJUSTMENT Measurement Item
Condition
Testequipment
Unit
Terminal
Adjustment Unit
12. TX RF low power
1) Measure the power level at TX ANT. Low CH 2) Center CH 3) High CH
Power meter Rear
TX ANT
13. BPF
1) Connect the TG to RX ANT, then connect CN1 to the spectrum analyzer input. Spectrum analyzer setting Span : 50MHz Scale : 10dB to 5dB div Tracking generator setting Output : –30dBm
Tracking Rear generator
RX ANT TX-RX (A/2)
Spectrum TX-RX analyzer (A/2)
CN1
14. MCF (Wide)
(Narrow)
15. Discriminator
16. Threshold squelch (Wide)
(Narrow)
42
1) Connect the TG to CN2, then connect CN4 to the spectrum analyzer input. CH : 2 (Wide) Spectrum analyzer setting Span : 50kHz to 25kHz Scale : 10dB to 2dB div Center freq‘ : 44.850MHz Tracking generator setting Output : –30dBm
CN2 CN4
2) CH : 2 (Narrow)
1) Connect the SSG to RX ANT. CH : 2 (Wide) SSG output : –53dBm/501µV SSG MOD : 1kHz SSG DEV : 3kHz AF : 2V/4Ω 1) Connect SSG to RX ANT. CH : 2 (Wide) SSG output : 3dB below to 12dB SINAD level SSG MOD : 1kHz SSG DEV : 3kHz AF : 2V/4Ω
SSG
Rear
AF VM Distortion meter
SSG Audio analyzer VTVM Oscilloscope
RX ANT
Parts
Method PC adj. 25W (Shipping power)
L2 L4 L5
Center the frequency you are using, then adjust it to look like the wave Fig. 1. (Page 46)
L14 L17 L18
Adjust it to look like the wave Fig. 2. (Page 46)
L15 L16 L19
Adjust it to look like the wave Fig. 3. (Page 46)
L24
Adjust the distortion to minimum.
Specifications/Remarks ± 1W
TEST/SPKR jack SPO (pin 12)
Rear
RX ANT TEST/SPKR jack SPO (pin 12)
PC adj. Adjust to point of opening squelch
2) SSG : OFF
Check
3) CH : 2 (Narrow) SSG output : 3dB below to 12dB SINAD level SSG MOD : 1kHz SSG DEV : 1.5kHz AF : 2V/4Ω
PC adj. Adjust to point of opening squelch
4) SSG : OFF
Check
Squelch must be closed.
Squelch must be closed.
TKR-850 ADJUSTMENT Measurement Item 17. Tight squelch (Wide)
(Narrow)
Condition 1) Connect SSG to RX ANT. CH : 2 (Wide) SSG output : 7dB over to 12dB SINAD level SSG MOD : 1kHz SSG DEV : 3kHz AF : 2V/4Ω
SSG
Unit Rear
Audio analyzer VTVM Oscilloscope
Terminal RX ANT TEST/SPKR jack SPO (pin 12)
2) CH : 2 (Narrow) SSG output : 7dB over to 12dB SINAD level SSG MOD : 1kHz SSG DEV : 1.5kHz AF : 2V/4Ω
18. RD outut level (Wide)
1) Connect SSG to RX ANT. CH : 2 (Wide) SSG output : –53dBm/501µV SSG MOD : 1kHz SSG DEV : 1.5kHz
(Narrow)
2) CH : 2 (Narrow) SSG output : –53dBm/501µV SSG MOD : 1kHz SSG DEV : 1.5kHz
19. RA outut level (Wide)
1) Connect SSG to RX ANT. CH : 2 (Wide) SSG output : –53dBm/501µV SSG MOD : 1kHz SSG DEV : 1.5kHz
(Narrow)
2) CH : 2 (Narrow) SSG output : –53dBm/501µV SSG MOD : 1kHz SSG DEV : 1.5kHz
20. Maximum deviation (Wide)
1) Connect AG to the MIC terminal. Low CH (TX VCO low) Center CH (VCO center) High CH (TX VCO high) Deviation meter filter HPF : OFF LPF : 15kHz De-emphasis : OFF AG : 1kHz/50mV (Terminal load) Transmission
(Narrow)
Testequipment
2) Low CH (TX VCO low) Center CH (VCO center) High CH (TX VCO high) Transmission
Adjustment Unit
Parts
Method
Specifications/Remarks
PC adj. Adjust to point of opening squelch
PC adj. Adjust to point of opening squelch
SSG
Rear
DVM
SSG
RX ANT
PC adj. 80mV
± 5mV
PC adj. 400mV
± 20mV
PC adj. 4.1kHz
± 0.1kHz
PC adj. 2.05kHz
± 0.1kHz
CONTROL I/O jack RD (pin 10) 4.7kΩ load
Rear
RX ANT
DVM
CONTROL I/O jack RA (pin 11) 4.7kΩ load
MOD ANA Rear or Deviation meter Oscilloscope
TX OUT
AG AF VTVM
MIC
Front
43
TKR-850 ADJUSTMENT Measurement Item 21. DQT balance (Wide)
Condition 1) CH : 2 Deviation meter filter HPF : OFF LPF : 3kHz De-emphasis : OFF Transmission
Testequipment
Unit
MOD ANA Rear or Deviation meter Oscilloscope
Terminal TX OUT
Adjustment Unit
Parts
Method PC adj. Make the demodulated waves into square waves.
Specifications/Remarks Oscilloscope DC range flat “A” part A
A (Narrow)
22. QT deviation (Wide)
(Narrow)
23. DQT deviation (Wide)
(Narrow)
24. CW ID deviation (Wide)
(Narrow)
25. Test tone deviation (Wide)
(Narrow)
44
2) CH : 2 Transmission PC adj. 0.75kHz
± 0.05kHz
2) CH : 2 Transmission
PC adj. 0.35kHz
± 0.05kHz
1) CH : 2 Deviation meter filter HPF : OFF LPF : 3kHz De-emphasis : OFF Detector : Peak hold Transmission
PC adj. 0.75kHz
± 0.05kHz
2) CH : 2 Transmission
PC adj. 0.35kHz
± 0.05kHz
1) CH2 Deviation meter filter HPF : OFF LPF : 15kHz De-emphasis : OFF Transmission
PC adj. 2kHz
± 0.1kHz
2) CH : 2 Transmission
PC adj. 1kHz
± 0.05kHz
1) CH : 2 Deviation meter filter HPF : OFF LPF : 15kHz De-emphasis : OFF Transmission
PC adj. 3kHz
± 0.1kHz
2) CH : 2 Transmission
PC adj. 1.5kHz
± 0.05kHz
1) CH : 2 Deviation meter filter HPF : OFF LPF : 3kHz De-emphasis : OFF Detector : p-p/2 Transmission
MOD ANA Rear or Deviation meter Oscilloscope
TX ANT
AG AF VTVM
MIC
Front
TKR-850 ADJUSTMENT Measurement Item
Condition
26. TA (TX audio input) deviation (Wide)
1) Insert AG output into the control I/O TA terminal (pin 9). CH : 2 Deviation meter filter HPF : OFF LPF : 15kHz De-emphasis : OFF AG freq‘ : 1kHz (Sine wave) AG level : 280mV Transmission
(Narrow)
27. TD deviation (Wide)
(Narrow)
28. Repeat gain level (Wide)
(Narrow)
Testequipment
Unit
Terminal
MOD ANA Rear or Deviation meter Oscilloscope
TX ANT
AG AF VTVM
CONTROL I/O jack TA (pin 9)
2) CH : 2 Transmission 1) Insert AG output into the control I/O TD terminal (pin 8). CH : 2 Deviation meter filter HPF : OFF LPF : 3kHz De-emphasis : OFF AG freq‘ : 100Hz (Sine wave) AG level : 0.5Vp-p (177mVrms) Transmission
MOD ANA Rear or Deviation meter Oscilloscope
TX ANT
AG AF VTVM
CONTROL I/O jack TD (pin 8)
2) CH : 2 Transmission 1) CH : 2 SSG output : –53dBm SSG MOD : 1kHz SSG DEV : 1kHz Deviation meter filter HPF : OFF LPF : 15kHz De-emphasis : OFF Transmission
SSG MOD ANA or Deviation meter Oscilloscope
Rear
RX ANT
Adjustment Unit
Parts
Method
Specifications/Remarks
PC adj. 3.0kHz
± 0.1kHz
PC adj. 1.5kHz
± 0.05kHz
PC adj. 0.75kHz
± 0.1kHz
PC adj. 0.35kHz
± 0.05kHz
PC adj. 1kHz
± 0.1kHz
TX ANT
1) CH : 2 Transmission
45
TKR-850 ADJUSTMENT ATTEN 20dB RL 10.0dBm
ATTEN 10dB RL –32.0dBm
MKR –26.17dBm 465.00MHz
10dB/
MKR –42.17dB 25.00kHz
10dB/
ATTEN 10dB RL –32.0dBm
10dB/
MKR –46.000dB 15.00kHz
More than More than 3dB Max. 3.75kHz 3.75kHz MKR 465.00MHz –26.17dBm
D
3dB Max. 5.5~7.5kHz 5.5~7.5kHz
3dB Max. 5.5~7.5kHz 5.5~7.5kHz
MKR D 25.00kHz –42.17dB
MKR 15.00kHz –46.000dB
D
More than 40dB
More than 40dB
More than 40dB
15kHz
15kHz
15kHz
G
G
CENTER 465.00MHz RBW 300kHz *VBW 300kHz
G
CENTER 44.85000MHz RBW 300Hz *VBW 1.0kHz
SPAN 50.00MHz SWP 50ms
Fig. 1
SPAN 50.00kHz SWP 2.0sec
CENTER 44.85000MHz RBW 300Hz *VBW 1.0kHz
Fig. 2
SPAN 50.00kHz SWP 2.0sec
Fig. 3
Adjustment Points
CN8 GND (BLACK)
FINAL UNIT (X45-363) (A/2) Component side view
CN6 MAIN DC (RED)
Q5
CN7 BACKUP (ORANGE)
CN2 RX
CN1 TX IN VR1
CN16
L5
L4
L2 CN18
TP102 TX CV
8
CN3
1
CN5
CN19 TC350 (VCO A)
CN15
L19
L16
CN4
L15
2 1
2 1
1
3
A2 : TX VCO (X58-481) CN1
CN2
NARROW L24
WIDE L18
L17
L14
CN3
TC350 (VCO A) A3 : RX VCO (X58-480)
TX-RX UNIT (X57-627) (A/2) Component side view
46
TP101 RX CV
TC351 (VCO B)
TKR-850 TERMINAL FUNCTION Connector Terminal Terminal I/O
Final Unit (X45-3630-XX) Connector Terminal Terminal I/O No.
No.
Terminal function
Name
CN1
DRV
I
TX driver input signal (Coaxial)
CN2
–
–
Reserved
VTH
O High temperature detector signal
CN3
1
No.
output To X57
2
BAT
O Main DC/BACKUP status output
(A/2)
3
PDT
O RF power down signal output
TX-RX
4
FAS
I
unit
5
PC
I
TX power control signal input
6
8T
I
8V input during transmission
7
RSW
–
Reserved
8
E
–
Ground
B
O Power supply output for cooling fan
FAG
O Fan ground
1
E
–
2
+B
3 1
CN4 CN5
CN6 CN7 CN8
Fan control signal input
1 1
CN501 To X54 (B/2)
1
STB1
I
Strobe data for shift register
14
CLK
I
Clock data input
15
DAT
I
Serial data input
16
PSW
O
Power switch output
17
GND
–
Ground
18
NC
–
No connection
19
SB
I
Power supply input after power switch
20
SB
I
Power supply input after power switch
Display Unit (X54-3330-20) (B/2) Connector Terminal Terminal I/O
Terminal function
CN601
1
VLI
O
Volume control output for AF signal
2
5M
I
Common 5V input
To X54
3
GND
–
Ground
O Power supply output
(A/2)
4
NC
–
No connection
+B
O Power supply output
display
5
SB
I
Power supply input after power switch
Main DC
I
unit
6
NC
–
No connection
terminal)
7
GND
–
Ground
Power supply input (from BACKUP
8
PTT
terminal)
9
MIG
–
10
MIC
O
MIC signal output
11
HOOK
O
Hook detection output/RXD output
BACKUP GND
I –
Ground
Power supply input (from Main DC
Ground
Terminal function
Name
I/O PTT output/TXD input
HOOK
1
NC
–
No connection
(Mic jack)
2
SB
O
Power supply output after power
3
E
–
4
PTT/TXD I/O PTT input/TXD output
5
ME
–
6
MIC
I
MIC signal input
7
HOOK/RXD
I
Hook detection input/RXD input
8
NC
–
No connection
switch I
Hook detection input/RXD input
2
MIC
I
MIC signal input
MIG
–
MIC ground
PTT
MIC ground
J601
Name
3 4
13
No.
Connector Terminal Terminal I/O No.
Terminal function
Name
No.
Display Unit (X54-3330-20) (A/2) No.
No.
I/O PTT input/TXD output
Ground MIC ground
display
5
GND
–
Ground
unit
6
NC
–
No connection
7
SB
O Power supply output after power
8
NC
–
No connection
9
GND
–
Ground
10
5M
O Common 5V output
CN1
–
–
O
11
VLI
I
Volume control input for AF signal
CN2
–
–
I
Use for RX MCF tuning
CN502
1
MIG
–
MIC ground
CN3
–
–
O
Use for RX frequency adjustment
2
MIC
O MIC signal output
To X57
3
VLI
O Volume control output for AF signal
CN4
–
–
O
Use for RX MCF tuning
(B/2)
4
5C
I
Common 5V input
CN14
1
NC
–
No connection
TX-RX
5
K4
I
KEY input 4
2
DET
O
Detection signal output
unit
6
K5
I
KEY input 5
3
NC
–
No connection
control
7
K2
O KEY output 2
(B/2)
4
GND
–
Ground
section
8
K3
O KEY output 3
control
5
ASQ
O
Squelch signal output
9
K1
O KEY output 1
section
6
RSSI
O
RSSI signal output
10
HOOK/RXD O Hook detection output/RXD output
of TX-RX
7
NC
–
No connection
11
SOE
unit
12
PTT/TXD I/O PTT output/TXD input
switch
I
Output enable for shift register
TX-RX Unit (X57-6270-XX) (A/2) : TX-RX Section Connector Terminal Terminal I/O No.
No.
Terminal function
Name Use for RX helical BPF tuning (Coaxial)
(Coaxial)
To X57
8
DP
I
Data input for PLL
9
CP
I
Clock input for PLL
47
TKR-850 TERMINAL FUNCTION Connector Terminal Terminal I/O No.
No.
Terminal function
Name
10
EPR
I
Enable input for RX PLL
11
EPT
I
Enable input for TX PLL
12
LDR
O
Lock detector for RX PLL
13
LDT
O
Lock detector for TX PLL
14
DT
I
Data input
15
CK
I
Clock input
16
STB4
I
Strobe input for shift register
17
FWD
O
RF power down signal output
18
LD2
I
Latch data input for DA converter
19
BUP
O
Backup signal output
20
PSW
I
Power switch input
21
TEMP
O
TX-RX Unit (X57-6270-XX) (B/2) : Control Section Connector Terminal Terminal I/O No.
No.
CN600
1
To X54
SOE
I
Output enable for shift register
GND
–
Ground
24
MB
I
Modulation signal input for VCXO
25
MO
I
Modulation signal input for VCO
26
GND
–
Ground
27
GND
–
Ground
28
NC
–
No connection
29
NC
–
No connection
30
SB
O
Power supply output after power
31
SB
O
display unit
32
SB
O
switch Power supply output after power
CN601
switch Power supply output after power switch 33
SB
O
Power supply output after power
NC
–
No connection
35
8C
O
Common 8V output
36
8C
O
Common 8V output
1
E
–
Earth
2
B
I
Power supply input
3
B
I
Power supply input
CN16
1
E
–
Earth
2
RSW
–
Reserved
To X45
3
8T
O
8V output during transmission
final
4
PC
O
TX power control signal output
CN15
unit
5
FAS
O
Fan control signal output
6
PDT
I
RF power down signal input
7
BAT
I
Main DC/BACKUP status input
8
VTH
I
High temperature detector signal input
48
CN18
1
RX IN
I
Receive signal input (Coaxial)
CN19
1
DO
O
Transmission signal output (Coaxial)
Power supply output after power
2
SB
O
Power supply output after power
3
GND
–
Ground
switch 4
NC
–
No Connection
5
DAT
O
Serial data output
6
PSW
I
Power switch input
7
STB1
O
Strobe data for shift register
8
CLK
O
Clock data output
9
SOE
O
Output enable for shift register
10
TXD1
I/O PTT input/TXD output
11
K1
I
KEY input 1
12
RXD1
I
Hook detection input/RXD input
13
K2
I
KEY input 2
14
K3
I
KEY input 3
15
K4
O
KEY output 4
16
K5
O
KEY output 5
17
VLI
I
Volume control input for AF signal.
18
5C
O
Common 5V output
19
MIG
–
Mic ground
20
MIC
I
MIC signal input
1
TXI
I
MIC signal input MIC signal output
2
TXO
O
To
3
RXI
I
RX audio signal input
optional
4
AC
O
Audio control signal output
board
switch 34
O
(B/2)
High temperature detector signal
23
Name SB
switch
output 22
Terminal function
5
BC1
O
Scramble code output.
6
BC2
O
Scramble code output.
7
BC3
O
Scramble code output.
8
BC4
O
Scramble code output.
9
PTI
I
PTT signal input
10
CLRC
O
Clear code for scramble
11
RXO
O
RX audio signal output
12
PTO
O
PTT signal output
13
5C
O
Common 5V output Ground
14 CN602 To X57
GND
–
1
8C
I
Common 8V input
2
8C
I
Common 8V input
3
NC
–
No connection
(A/2)
4
SB
I
Power supply input after power switch
TX-RX
5
SB
I
Power supply input after power switch
unit
6
SB
I
Power supply input after power switch
7
SB
I
Power supply input after power switch
8
NC
–
No connection
9
NC
–
No connection
10
GND
–
Ground
11
GND
–
Ground
12
MO
O
Modulation signal output for VCO
13
MB
O
Modulation signal output for VCXO
TKR-850 TERMINAL FUNCTION Connector Terminal Terminal I/O No.
CN603
No.
Terminal function
Name
No.
GND
–
Ground
9
RD
SOE
O
Output enable for shift register
10
IO3
16
TEMP
I
High temperature detector signal input
11
TA
17
PSW
O
Power switch output
12
IO2
18
BUP
I
Backup signal input
13
TD
19
LD2
O
Latch data output for DA converter
14
IO1
20
FWD
I
RF power down signal input
15
DG
–
Control line ground
21
STB4
O
Strobe output for shift register
16
TXG
–
TX signal ground
22
CK
O
Clock output
17
AI3
I
Auxiliary input 3 (FPU selectable)
23
DT
O
Data output
18
NC
–
No connection
24
LDT
I
Lock detector for TX PLL
19
AI2
I
Auxiliary input 2 (FPU selectable) Squelch control output
I
TX audio input (voice)
I/O Programable I/O 2 I
TX data input (data or signaling)
I/O Programable I/O 1
LDR
I
Lock detector for RX PLL
20
SC
O
EPT
O
Enable output for TX PLL
21
AI1
I
Auxiliary input 1 (FPU selectable)
27
EPR
O
Enable output for RX PLL
22
EPTT
I
External press-to-talk switch input
28
CP
O
Clock output for PLL
23
TXD2
O
RS-232C output signal (for FPU)
29
DP
O
Data output for PLL
24
EMON
I
External monitor switch input
30
NC
–
No connection
25
RXD2
I
RS-232C input signal (for FPU)
31
RSSI
I
RSSI signal input
26
NC
–
No connection
32
ASQ
I
Squelch signal input
27
NC
–
No connection
33
GND
–
Ground
28
NC
–
No connection
34
NC
–
No connection
29
NC
–
No connection
35
DET
I
Detection signal input
30
NC
–
No connection
36
NC
–
No connection
1
SB
O
Power supply output after power Power supply output after power
3
GND
–
Ground
4
GND
–
Ground
1
AO5
O
Auxiliary output 5 (FPU selectable)
2
AO4
O
Auxiliary output 4 (FPU selectable)
To ACC
3
AO3
O
Auxiliary output 3 (FPU selectable)
15 pin
4
SPO
O
External speaker output
connector
5
SPO
O
External speaker output
6
AO2
O
Auxiliary output 2 (FPU selectable)
7
AO1
O
Auxiliary output 1 (FPU selectable)
8
SPI
I
Internal speaker input
9
RSSI
O
RSSI signal output
10
RD
O
RX data output
11
SPG
–
External speaker ground
12
SPG
–
External speaker ground
1
SP
O
Internal speaker AF output
2
SPG
–
Internal speaker ground
1
NC
–
No connection
2
NC
–
No connection
To ACC
3
SPM
I
Speaker mute signal input
25 pin
4
IO6
D-sub
5
RXG
connector
6
IO5
7
RA
15 pin
CN606
RX data output (voice & data)
26
O
CN605
O
I/O Programable I/O 3
25
SB
CN604
Terminal function
Name
15
2
connector
No.
14
switch To ACC
Connector Terminal Terminal I/O
switch
8
IO4
VCO (RX) Unit (X58-4800-XX) Connector Terminal Terminal I/O No. CN300
CN350
CN351
No.
Terminal function
Name
1
FIN
I
Prescaler RF signal input
2
5C
I
Common 5V input
3
LDR
O
Lock detector for RX PLL
4
EPR
I
Enable input for RX PLL
5
DP
I
Data input for PLL
6
CP
I
Clock input for PLL
7
REF
I
Reference frequency signal input
1
GND
–
Ground
2
SRR
I
Switching signal input for RX VCO
3
8CL
I
8V input through the ripple filter
4
CV
I
RX PLL lock voltage
5
9CL
I
9V input through the ripple filter
6
NC
–
No connection
1
VO
O
RX VCO output
2
GND
–
Ground
VCO (TX) Unit (X58-4810-XX) Connector Terminal Terminal I/O
Terminal function
No.
No.
CN300
1
FIN
I
Prescaler RF signal input
2
5C
I
Common 5V input
I/O Programable I/O 5
3
LDT
O
Lock detector for TX PLL
O
4
EPT
I
Enable input for TX PLL
5
DP
I
Data input for PLL
I/O Programable I/O 6 –
RX signal ground RX audio output (voice)
I/O Programable I/O 4
Name
49
TKR-850 TERMINAL FUNCTION Connector Terminal Terminal I/O No.
CN350
CN351
No.
Terminal function
Name
Connector Terminal Terminal I/O No.
CP
I
Clock input for PLL
7
REF
I
Reference frequency signal input
1
GND
–
Ground
2
STT
I
Switching signal input for TX VCO
3
8CL
I
8V input through the ripple filter
4
CV
I
RX PLL lock voltage
5
9CL
I
9V input through the ripple filter
18
NC
-
6
MO
I
Modulation signal input
19
TXG
-
1
VO
O
TX VCO output
2
GND
–
Ground
Connector Terminal Terminal I/O No.
–
No connection
2
RXD2
I
Serial data to radio
3
TXD2
O
Serial data from radio
4
AI1
I
Programmable function input 1
5
AI2
I
Programmable function input 2
6
AI3
I
Programmable function input 3
7
DG
–
Control line ground
8
TD
I
TX data input (data or signalling) Input impedance: 600Ω Coupling: AC coupling Deviation: 0.75kHz (wide)/ 0.35kHz (Narrow) (100Hz 0.5Vp-p input)
9
TA
I
TX audio input (voice) Input impedance: 600Ω Coupling: AC coupling Deviation: 60% deviation (1kHz 280mVrms ± 25mV input)
10
RD
O
RX data output (voice & data) Output impedance: 1kΩ or less Coupling: AC coupling Frequency response: ± 2.5dB at 10~3000Hz Output level: 70~90mVrms (standard modulation)
11
RA
O
RX audio output (voice) Output impedance: 1kΩ or less Coupling: AC coupling
EMON
I
16
EPTT
I
17
SC
O
External monitor switch input External press-to-talk switch input “L”: PTT on, “H”: PTT off Squelch control output “L”: Busy, “H”: Not busy No connection TX signal ground (for TA,TD ground only)
Name NC
15
“L”: Monitor on, “H”: Monitor off
Terminal function
1
Terminal function
Name
6
ACC 25 pin D-sub Connector No.
No.
20
AIO1
I/O Programmable function input/output 1
21
AIO2
I/O Programmable function input/output 2
22
AIO3
I/O Programmable function input/output 3
23
AIO4
I/O Programmable function input/output 4
24
AIO5
I/O Programmable function input/output 5
25
AIO6
I/O Programmable function input/output 6
13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14
ACC 15 pin Connector Connector Terminal Terminal I/O No.
No.
Terminal function
Name
1
SB
O
Power supply output after power
2
SB
O
3
NC
–
No connection
4
GND
–
Ground
5
GND
–
Ground
6
SPG
–
Speaker ground
7
RD
O
RX data output
8
RSSI
O
RSSI output
9
SPI
I
Internal speaker input
10
AO1
O
Auxiliary output 1
11
AO2
O
Auxiliary output 2
12
SPO
O
External speaker output
13
AO3
O
Auxiliary output 3
14
AO4
O
Auxiliary output 4
15
AO5
O
Auxiliary output 5
switch; 1A maximum Power supply output after power switch; 1A maximum
Output level: 360~440mVrms (standard modulation) 12
RXG
–
RX signal ground (for RA,RD ground only)
13
SPM
I
14
NC
-
Speaker mute signal input “L”: Mute on
50
No connection
13 10 7
4
1
14 11 8
5
2
15 12 9
6
3
TKR-850
TKR-850
WIRING
51
52
D
C
B
A
E
F
I
H
G
J
TKR-850
PC BOARD VIEWS RX PLL/VCO (X58-4800-XX) -10 : K,E -11 : K2 Component side view
RX PLL/VCO (X58-4800-XX) -10 : K,E -11 : K2 Foil side view
J72-0751-02 A/2
J72-0751-02 A/2
C379
R365
C377 R366
C378 R367
Q355
L360 Q350
R368
L362
R376
2
C374 R359
C370
C368
R373
S
C366
R372
C380
G C364 R354 DD354
C366
L358
CN351
Q350
VO
C367
S G D354D
1
R354 C364
2 GND
R373
Q351 G
C368
D
VO
L359
C370
C380
L358
C366
S
L360
R359 C374
C371
2 GND
1
Q350 C364 R354 R355 C365
R376
R372
D
G
C375
CN351
S
R367 R357 Q353 R364 L361 R358 C373
C369
C368
Q350 S C365 R355 R354 C364 G D L358 L359 C366
R359
R366 C378 R367
R361
R363
L362 Q355
C370
R366
Q354
C370
C374
C377
C378
C376
Q352
L360
C377
R365
R356
Q355
R362
C372
R360
C379
R368
R368
L362
1
J72-0752-02 A/2
R365
CN351
VO
C379
TX PLL/VCO (X58-4810-XX) -10 : K,E -11 : K2 Foil side view
J72-0752-02 A/2
1
C374
2 GND
C367
L360
C368
D
C372
S
VO
G
C369
Q351
R356
Q352
R359
2 GND
1
C375
C371
C376
C373
Q354
R367 R364 L361 R358
R360
Q355
C378
R357
Q353
L362 R362
R366
R363
C379
R365
R361
CN351
R368 C377
TX PLL/VCO (X58-4810-XX) -10 : K,E -11 : K2 Component side view
L358
C386
C386
L356
L356
L357
L356
L356
L357
3 C356
C362
CV
9CL
MO 6
5C
LDT
EPT
DT
REF C306
R302
R303
C305 C304 1
IC300 R310
C309 10
C308 L300
20
11
C307
R304
R301 R305
C312
R311 R308
C312
C310
C314
C321
C314
CP
R300
R319
C317
L301
6
R306 R312
C318 +
Q300
C324 +
Q301
R320
C323
C315
R309 R318 R314 C311 + R313
J72-0752-02 B/2
L301
+ C324
C317
L302
L302 R311 R308
C310
R320
C323
5
L303
C321 11
R318 + C311
C307
C325
R322 C319
FIN
C322
R322 C319
Q302 R321
R319
Q302 R321
C325
R315
C322
7
8CL
4
1 CN300
CN300
FIN
R300 10 C309
R316
R313 Q301
C315
R317 + C320
C350
STT
GND 1
CN350
CN350
5C
R305
R310 IC300
20
J72-0751-02 B/2
GND 1
8CL
LDT R301
1
R316
Q300
Q300
C315
C320 + R317
+ C318
R315
L303
R309
R314
C382
C383
L353
L352
R353
1
CV
EPT
R304
R303
R302 L300
L300
20
C324 +
C354
L354 C359 C360 D350 D352 C354 R351 C351
STT
9CL
C306
CP
REF
C306
DT
7
REF
1
R312
C318 +
L352
R353
L353
C350
D352 R351
MO 6
7 R302
R303
C308
R309 R312 R318 R314 C311 +
C323
C362
C356 C383
C382
L350 CP
J72-0751-02 B/2
C308
R306
R320
+ C324
C305 C304
R306
R313 Q301
C323
R304
11
R308
R320
R313 Q301
C315 R316
R318 + C311
DT
EPR C305 C304
IC300 R310
C309 10
C310
C307
C359 D350 C360
TC350
C351
6 R301 R305
C321
C312
C313
C312
R311
C314
C316
C314
L301
L301
C313
C317
L302
L302
C316
11
20
R311 R308
C310
10 C309
C317
TC350
L354
R300 R319
L303
C321
R305
R310 IC300
1 L300
C307
C325
R322 C319
FIN
R322 C319
Q302
C322 R321
R321
Q302
R319
R315
C322
C357
NC
LDR
9CL
CV
5C
1
C325 R300 R301
R304
R303
R302 Q300
+ C318
R317 + C320
C358 D351 C361
R350
8CL
SRR
CN300
CN300
FIN
C306
R315
L303
R309
R314
TC351
L351
R352
R306 R312
C363
R353 C351
1
DT
CP
REF
C308
D353 C350
D352 R351
GND 1
CN350
CN350
5C
GND 1
8CL
LDR
SRR
CV
EPR
6
9CL
NC
7 C305 C304
L355
C383
C354
C355
C356
C359 L354 D350
C360
L353
C354
TC350
L352
L352
L353
C350
D352 R351 R353 C351
R352
R350
C359 D350 C360
C362
D353
L351
L350
C357
TC350
L354
C383
C358 L355 C361 D351
C362
C356
C355
C363
TC351
C320 + R317 R316
7
J72-0752-02 B/2
54 Component side
Foil side
Component side
Foil side
B
A
TKR-850
C
E
D
G
F
H
I
J
PC BOARD VIEWS
1
DISPLAY UNIT (X54-3330-20) Component side view J72-0756-02 A/2
J72-0756-02 B/2 VLI 1 5M GND NC SB NC GND PTT MIG MIC HK 11
CN601
S507 Q523
34 1 6
61 43
CP504
34 1 6
Q521
61 43
Q517
CP501
34 1 6
R605
61 43
Q516
D601
Q518
61 43
CP502
34 1 6
D602
D507 Q524
D506
C602
Q522
C606
D603
C603
VR601
Q519
2
CP503
3
BACKUP RED
MAIN DC GRN
R601
4
C507
D501
Q501
Q502
C503 + R507
VR501
R544 R535
R536
Q507
8 9
1 IC502
R534 R537 C511
D509
C526
S506
C518
R526 Q514 16 34
Component side
1
Foil side
DTA144EUA DTC363EK DTD114EK DTD123EK 2SA1586 2SC3356 2SC4116
6
2SK2596
7
55
2SC4226 2SC4617 3SC5110
2SB1132 2SC3357
DTA114EUA DTC114EUA DTC144EUA
LA4422
NJM4558E
DAN235K
TA78L05F
DA204U HSM88AS
VREF GND VIN
2SK508NV
UPA672T
2SJ506
2SK1824
BU4094BCF
TC7S00F TC7S04FU TC7S66FU
AN8009M
TK11050M
MA742
R519
Q510
Q511
R520
D513
D514
D510
D511
R539
R540
D512 C525
IC507 I G O
VLI 5M GND NC SB NC GND PTT MIG MIC HK
6 1 43
R538
D508
C523
C522
C521
O G I
S505 R505
5
D502
R510 C506 C504
1
IC501
C517
C501 +
16 34
8
C505
BUSY
Q504 RED
11
R525
R506
Q513
R511
R509
+
C509
R514
R512 R513
C510
R533
C516
S504 C508
S503 R529
D504
IC506
CN502
R508
R524
1 2 MIG MIC VLI 5C K4 K5 K2 K3 K1 HK/RXD SOE PTT/TXD STB1 CLK DAT PSW GND NC SB SB 19 20
R523 C515
R531 R530
R532 C514
16
IC503 8
Q512
6 1 43
1
9
S502
S501
5
R522
C512
R521
C513
GRN + Q508
TX
4
+ C502
D503
R516
GRN
34 16
R543
+ C524
Q506 RED
R606
16
R517
DG S
9
R541
8
R542
9
Q525
IC505
R502
8
SB
16
1
IC504
C520
16
1 J601
R503
GND
PTT
CN501
MIG
R604
C607
MIC
C519
NC
HOOK
NC
C605
D505
D
C
B
A
F
E
I
H
G
J
TKR-850
PC BOARD VIEWS
1
DISPLAY UNIT (X54-3330-20) Foil side view J72-0756-02 A/2
J72-0756-02 B/2 11 HK MIC MIG PTT GND NC SB NC GND 5M VLI 1
CN601
VR601 D506 Q519
D603
43 61
D602 D601
43 61
Q516
1 6 34 1 6 34
CP503
CP501
2
C603
R605
MAIN DC GRN
Q522
43 61
1 6 34
Q521
BACKUP RED
C602
CP502
Q518
43 61
1 6 34
Q523
CP504
Q517
Q524
D507 S507
C606
R601
3
1
Component side
R604
MIC PTT SB
HOOK MIG GND
C607
C605
8
R516
NC
GRN
TX
Q513
R521 IC503
9
C512
R523
C514 R532
1 6 34
S501 8
R533
S502
16
R514
+
R522
1
5
R529 S503
C510
IC501 4
C509
C508 S504 R511 R512 R513 1 8
C513 R530 R531
CN502
C515
19 20 SB SB GND NC DAT PSW STB1 CLK SOE PTT/TXD K1 HK/RXD K2 K3 K4 K5 VLI 5C MIG MIC 1 2
4
R524
C521
D501
R509
R507
Q501
C505 C504 C506 R510
+ C503 + C502
VR501
+ Q508
C522
I G O
C523
IC506 D502
S505
D503
C516
R525
C517
Q502
VLI 5M GND NC SB NC GND PTT MIG MIC HK
R508
61 43
9
GRN
R506
Q514
BUSY
R505
R503
R526
J601
RED D504
C501 +
S506
R502
C518
CN501
C526
NC
1
IC504
8
11
O G I IC507
C525
C511
C519
C520 R541
R542
Q504
D508
D509
16
Q506
43 61
RED
+ C524
1
R534 R537
16
IC502
9
8
R538
1
9
R517
R606
D512
R540
R539
R536
Q507
R535
R544
1 6 34
S DG
R543
16 IC505
Q525
D511
D510
D514
D513
R520
Q511
Q510
R519
D505
5
Q512 61 43
C507
Foil side
30622M4-113GP
320VC5402PGE
AT29C020-90TI
TA75W01FU TC75W51FU
AT2408N10SI2.5
TA75S01F
SA7025DK
BU4053BCF
NJM7808FA
TA7808F
ADM202EARN
NJM78L05UA RH5VL42C
TK14489V
AK4550VT BU4094BCFV M62354GP TC74VHC4040FT
M62364FP TC74LVX4245FS 6
2SK3075
7
58
A
1
2
C
B
TKR-850
D
E
F
G
I
H
J
K
L
N
M
O
P
Q
S
R
PC BOARD VIEWS
FINAL UNIT (X45-3630-XX) -10 : K,E -11 : K2 Component side view CN8 GND (BLACK)
CN6 MAIN DC (RED)
J72-0755-02 A/2 C54
ANT
D7
+
3
C51 +
C80
C55 L11
J72-0755-02 B/2
C89
+
4
CN7 BACKUP (ORANGE)
L12
K1
11
C59
L9 C81
R43
R33
C71
R36
R38
D4
C61
R37
R56
1
GND RSW 8T PC FAS PDT BAT VTH 8
CN3
C72
R44
C27
Q8
C28 VR1
R41
C69
C70
R3
R2 L1
C75
D2 C8
TH1
D5
CN2 RX
L8
R45
REV
Component side
Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC1 7J Q3 9F D2 9J D8 6E IC3 9J Q4 5I D4 7Q D9 7E Q1 10H Q5 5M D5 9R D51 7B Q2 10G Q8 9K D7 3K D52 8B
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side
13
59
C45
R22 R24 1
IC3
12
14
R40
R60 R57 R58
4
8
C30 C29
5
C1
R48
Q2
CN1 TX IN
R46
C7
C4
R4 C6
R9
C14
R47 C12
R1
R8
C83
C106
C108 C24 +
C26
C25
C20
R26 R55 R59
R62
L2
E
B CN5
C120
R13
L3
C60
S
FWD
R11
Q1
10
1
3
B
C5
1
R12
C17
FAB
2
C13
FAG
Q3 D S G
S
R20 R21
C21 CN4
C118
C48
R51
R49
L15
1
C109 C107
C23
IC1
C22
D
Q5
R23
R19
4 3 6
C86
C46
R52
C38
L14 +
C3
D52
8
9
C41 R53
R17
C35
R15
D9 CN52
D51 CN51
7
G
R18
C34
C33
C32
C31
D8 R61
6
C42
G Q4 D S
C58
S L5
S
C44
CHARGE
R34 R35
5
L6
S
L7
C57
C39
60
A
B
C
D
E
F
G
H
J
I
K
L
M
O
N
P
Q
S
R
TKR-850
PC BOARD VIEWS
1
2
FINAL UNIT (X45-3630-XX) -10 : K,E -11 : K2 Foil side view
C52
C53
J72-0755-02 A/2 3 C115
C116
C117
C77
C78
C79
C49
C50
C114
GND BLK
C105
GND BLK
+B1 RED
4
5
R54
+B2 RED
J72-0755-02 B/2
6
7
C64
D3
C65 S D G
Q7
C66
C68
C67
8
C112
C113
C100
C98
D10
C19
C99 R7 C10
C92 C91
C95 C94 C93
C97 C96
C104
C15
R6
Q9
C16
C9
C18
R50
IC2 I G O + C103
9
C101
+B2 ORG
GND BLK
+B1 RED
10
C102
Component side
Ref No. Address Ref No. Address IC2 9O D3 7B Q7 7B D10 9O Q9 9O
Pattern 1 Pattern 2 Pattern 3 Pattern 4
11
Foil side 12
13
61
62
14
A
E
F
G
I
H
J
K
L
N
M
O
P
Q
S
R
PC BOARD VIEWS
FINAL UNIT (X45-3630-XX) -10 : K,E -11 : K2 Component side view + Foil side CN8 GND (BLACK)
CN6 MAIN DC (RED) C53
J72-0755-02 A/2 ANT +
3
C54
2
TKR-850
D
C52
1
C
B
12
L7
C57
L9 C81
R43
R33 D4
C61
C45
R22 R24 R23
D3
Q7 C64
C71
R38
R36
S D G
C67 C68
1
CN3
C72
R44
C96 C97
C91 C92
D5
GND RSW 8T PC FAS PDT BAT VTH
C93 C94 C95
C27
Q8
R58
C28 VR1
R56
C69
C1
C70
R2
C7
C4
R3 R46
L1
R41
8
C8
L2
R1
CN1 TX IN
TH1
C75
D2
C30 C29
1
IC3
CN2 RX
L8
R45
REV
Component side
Ref No. Address Ref No. Address Ref No. Address IC1 7J Q5 5M D5 9R IC2 9E Q7 7R D7 3K IC3 9J Q8 9K D8 6E Q1 10H Q9 9E D9 7E Q2 10G D2 9J D10 9E Q3 9F D3 7R D51 7B Q4 5I D4 7Q D52 8B
63
R37
C65
R60 R57
R34 R35
4
8
R62 R4 C6
R47 R7 C12
5
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side Connect 1 and 4
13
14
R40
C106
C108 Q2
C83
C66
R26 R55 R59
R6
R48
R8
C60
S
FWD
C120
C24 +
C25
C18 C26
C20 L3
C9 C14 R9 C10
C17
C5
C113 E
B
C112
B
R11 C15
Q1
C102
CN5
1
C103 +
3
IC2 I G O
C16
R13 C13
Q9 C104
D10
C100
FAB C99 1
C19 R12
S
R20 R21
C21
11
2
Q3 D S G
C118
C48
R51
R49
L15
1
C109 C107
C23
IC1
6
C22
L14
10
+B2 ORG
CN4 FAG
C101
GND BLK
C41 R53 4 3
D
Q5
C46
R52
R19
D9
R15
C35
C38
R50
+
C3
D52
C98
9
G
R18 R17
R61 CN52
D51 CN51
C42
G Q4 D S
C34
C33
C32
D8
C31
L5
C86
C59
S C105
C58
CHARGE
S
C44
L6
S
R54
+B2 RED
6
+B1 RED
C49
+ C39
5
8
C50
C51
C78
C77
C80
C55
K1
GND BLK
7
C89
L11
+B1 RED
GND BLK
L12
+
J72-0755-02 B/2
C116
4
CN7 BACKUP (ORANGE)
C117
C114
C79
D7
C115
64
A
B
E
D
C
F
G
H
J
I
K
L
M
O
N
P
Q
PC BOARD VIEW
S
R
TKR-850
1
TX-RX UNIT (X57-6270-XX) (A/2) -10 : K,E -11 : K2 Component side view 2 8
CN16
CN19
GND RSW 8T PC FAS PDT BUP VTM
1
J72-0758-01 A/2
3 C125
GND2 L5
L4
L2
VO
+ GND1
CN18
TP102 TX CV
+
CN1
8CL CV
C137
4
STT
FIN 5C
A2 : TX VCO (X58-481)
LDT
9CL
EPT
MO
DP
5
C139 2 1
FC DP CP EP LD
R31
R11
C48
R13
XF2
A10
GND2
WIDE L17
R44
PSW
7
A9
D2
L24
A1
FCR
CN3
FCT
EPR
NC
DP
R129
9
5C
A3 : RX VCO (X58-480)
LDR
10
CP C144
+ C147
B C E
R128
Q17
Q16
9V
36
C158
+
35
2
9CL +
G
REF
C138 +
11
+
LD EP DP CP
O
C171
I
C174
R137
MO
C173 C172
I
C136
FIN
IC10 R139
G
SB
R141
O
1
IC4
CN4
8CR
NC DET NC GND ASQ RSSI NC DP CP EPR EPT LDR LDT DT CK STB4 FWD LD2 BUP PSW TEMP SOE GND MB MO GND GND NC NC SB SB SB SB NC 8C 8C
F1
8CR
SRR TP101 RX CV 8CL CV
STB4
C161 C160
DT
R138
R140
R142
CK
GND1
+
LD2
I G O IC5
TX
Q4
R69
C76
+
C159
SRR STT SOE 5CR K1
8
VO C124
C67
R46
L15
R41 C37
R10
C74
6
R32 R30
D1
XF1
C66 R60
L33
C15
L14
C196
L18
11
C14
NARROW
C214
R62 R63
R57
10 CF2 NARROW
CF1 WIDE
R61
IC9
R59
C64
R54
C51
L19
20
1
C213
C60
+
CN2
R45
L16
X1
CN4
R65
L20
CN15
C58 C59
R50 C53
1
3
2 1
B
B
B
CP REF
12 Component side
Ref No. Address Ref No. Address Ref No. Address IC4 11A IC10 11I Q17 10J IC5 10I Q4 10E D1 7I IC9 7D Q16 10K D2 7E
Pattern 1 Pattern 2 Pattern 3 Pattern 4
13 Foil side
65
66
14
A
1
C
B
D
TKR-850
E
F
G
I
H
J
K
L
N
M
O
P
Q
S
R
PC BOARD VIEW
TX-RX UNIT (X57-6270-XX) (A/2) -10 : K,E -11 : K2 Foil side view 2
J72-0758-01 A/2 R5 C4
Q13
C5 C199
L1 R52 C55
R47
C56 R53
R83
C54
L21
D3
C57
Q3
R49
R48
C50
C47
C45
C42
R58
C62
R55
D4 R56
R161
C49
C44
C46
C43
R163 R164
C68
Q2
C155
D11
Q7
D5
R64 R68
+
C72 +
C153
C78
C156
C77
C79
R71 C185
R72
C189
C148 C149
11
C75
R66
C151
R67
TH1
C190
C184
C73
C157
C154 +
C71
12
13
14
Component side
Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC1 4C IC11 6E Q6 9N Q11 3C Q18 5E Q25 9R D8 3D IC2 10E Q1 3N Q7 11P Q12 9G Q19 5F D3 7R D9 3P IC3 10E Q2 7K Q8 8C Q13 4G Q20 2F D4 8R D11 10N IC6 9K Q3 7O Q9 8D Q14 10G Q23 3E D5 11O D12 9R IC7 9L Q5 9N Q10 8E Q15 5G Q24 9S D7 9S
67
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side
68
D7
C162
Q25
Q24
R166
R165
Q5
D12
9
Q6
C130
C132 C134 R126 R124 C140
IC3 +
C39
L12
R123
C142 Q14
1 C145
+
C146
L32
X2
IC2
R160
C163
Q12
4
8
C84 R75 C83
REF
5
O G I
R76 R73
R158
C81
R157
CP
R77
DP
C90 C117 C116
10
C88 R88
R120
8
5C EPR R156
C197
R42
IC7
C122 C121
LDR R155
C40
16
C128
C69 C70
R14
C126 +
FIN
9
R36
C36
C105
C198
C65 +
C63
L27
L13
1
C104 C106 R105
C61
R150
1
L26
R113
R39 R38
16
C102 R107
R40 C38
C97 R100 C98 R99
C34
R114
C52
IC6
R103
C107
R98
Q10 B C E
C109
R102
C32 R35
L29
R51
B C E
L10
C30 R33
C31
8
L25
Q9
R97
L30 C111
Q8
C100
C41 R43
9
8
C95
L23
R34
C33
7 R91
D9
R9 R8
C13
L11
C212
+
C133 C135 R125 C141
R37
C87 C175 C176
IC11
O G I
C177
C80
+
Q15
R131
R90
C150 Q19
R87 C152
Q18 B C E R130
X3
R92
C209
C86
+
C143 R127
+ C24
+
C3
R1
R2
L3
C2
C195
C207
C194
C206
C193
C192
C205
C204
C191
C208
C210
R143
R121
L6
R122
R78
R162 C91 C92 R94 GND2 C93 VO R93
C7
E C B
C131
+ C85
L31
6
C129 C123
+ C25
C178
R154
C127 +
R17
R74 C82
CP
C89
R153
C115 C114
DP
1
C179
EPT R152
REF
IC1 8
LDT R151
5
C211
C120
4
R19 R20 R17
5C
5
R18
FIN
Q1
C167 R79 R82
4
Q23
C101
L28 C99
R148
D8
C28 C29
VO L42
R106 R109
C94 R95
GND2
R96 C96 R101
3
Q11
R136 R135
R3
Q20
L34
R133
L40
L38
L39
L37
L35
C164 R144 R134 C166
L36
L41
A
B
E
D
C
F
G
H
J
I
K
L
M
O
N
P
Q
S
R
TKR-850
PC BOARD VIEW
1
TX-RX UNIT (X57-6270-XX) (A/2) -10 : K,E -11 : K2 Component side view + Foil side
Q11
C29 C28
C99
R101 C96 R96 R79 R82 C179
E C B Q18
C94 R95
L28
C101 R109
Q23
R143
R152
EPT
R153
DP
R154 C114 C115
C80
C178
R74 C82
5
CP REF
L31
+
6
FC DP CP EP LD
+
C89
BUPL36
VTML35 8 C204
PDTL37
C205
C191
FASL38
C206
C192
PC L39
C207
L40 8T
C166 R134 R144 C164
R78
LDT
L27
C124
C102 R107
C97 R100 C98 R99
L26
Q8 L25
R92 C91 R162 C92 R94 GND2 C93 VO R93
IC2 8
1
+
C84
X2 +
R155
LDR
R156
EPR
R157
DP
R158
CP
C116 C117 C90
5
R77
NC
I G O
C142 C132 C134 Q14 C140 R124 R126
4
C81
CV 9CL
9
5C
A3 : RX VCO (X58-480) R76 R73
R88
C88
+
8
FIN
C146
C130
C138
R98
C104 R105 C106
R91
R97
R103
R75 C83
R129
G
C144
C147
Q16 B C E
R128
Q17
+
Q9
C145
R123
RX CV 8CL
+
9V
C95
C100 R102
C122 SRR C121 TP101
C136
C159
5C R151
GND1
C128
+
8CR
C158
4 FIN
8
X3
IC3
FCT
I G O IC5
R120
C149 C148
8 IC6
1 16
1 C161 C160
C111
C109
C107
C105
Q12
+
IC1
C85 +
A2 : TX VCO (X58-481)
C177
R127 C143
R10
R113
CN3
+ C154
35
Q10 B C E
R114
A10
36
F1
L30
+ C126
C155
5
1
IC11
C13
R8 R9 R31 C30 R33
R13
L29
C36
LD2
4
L11
L33
C212 L10
L12
R36 R37
E C B C38
C43
L14
IC7
10
REF
L32
11
I
O
+
C171
MO
LD EP DP CP
IC10 C174
Q6
Q4 Q5
C76
8
DT
C173 C172
C71
D5
R141
SB C157
I
C156
G
C78
+ C72
R139 C185 R137 C189
C151
C153
O
+
C75
C77
DET D11 NC GND ASQ RSSI NC DP R142 CP EPR EPT R140 LDR LDT DT C184 CK STB4 R138 FWD LD2 BUP PSW TEMP C190 SOE GND MB MO GND GND NC NC SB SB SB SB NC 8C 8C
IC4
R64 R68
R71
8CR
R67
C79 CN4 1 2 R72 NC TH1
R69
R165
R66
Q7
R11
C34
STB4
CK
+
VO
L42
R130 R131
GND2
7
FCR
16
9
D12
Q25 R166
Q24
C162
D7
C73
TX
Q19
3
A1
C32 R35
R42
SRR STT SOE 5CR +
R39 R38
C40
WIDE
C15
C33
L13
C163
K1
D1
MO
C139
R32 R30
9
L17
C44
C46
L18
C214 R163
R44
Q2
L15
C42
C39
L16 C47
C50
L19
R46 R48
C45
C57 C213
Q3
R61 C54 C67 R49
R164
C49
R161
C48
L24
XF2
C14
C31 R41 C37
R40
R150
C63
C68
D4
R58
C62
PSW
R56
R55
C74
A9
D2
L21
C197
C41 R43
NARROW
XF1
C66 C52 R60 R57
C196
R59
R62 R63
R14
11
R51
R34
+
CV 9CL
Q15 C133 C135 C141 R125
2 1
2 1 X1 IC9 10
C51
R54
20 1 + C65
R65
CF2 NARROW
CF1 WIDE
C69 C70
C60
C61
R83
L20
R53
D3
C56
R47
C58 C59
R50 C53
1 R52
R160
C198
C24 +
+
CN2
R45
C86 8CL
+
B
B
B 3
C55
C64
CN4 L23
C25 +
R87
C137
CN15
STT
R20 R17 R19 R18
TP102 TX CV
C131
D8
C167
I G O
R122
R106
R148
GND1
C120
C150
+
Q13
CN1
R135 R136
R17
C176 C175
C5 C199
CN19
C129 C123
C152
R121
C194
C208 C195
+ C127
L5
R90
CN18
L4
C87
C7
C125
L3
C210
R3 R2
L34
C209
R1
C211
C2
D9
L1
C3
L2
Q1
E C B
L6
Q20
2
CN16 RSW
R5 C4
GNDR133 1
L41
C193
J72-0758-01 A/2
12 Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC1 4Q IC6 9I Q1 3F Q6 9F Q11 3Q Q16 10K Q23 3O D3 7B D9 3D IC2 10O IC7 9H Q2 7I Q7 11D Q12 9M Q17 10J Q24 9A D4 8B D11 10F IC3 10O IC9 7D Q3 7E Q8 8Q Q13 4M Q18 5O Q25 9B D5 11E D12 9B IC4 11A IC10 11I Q4 10E Q9 8P Q14 10M Q19 5O D1 7I D7 9A IC5 10I IC11 6O Q5 9F Q10 8O Q15 5M Q20 2N D2 7E D8 3P
69
Component side Pattern 1 Pattern 2 Pattern 3 Pattern 4
13 Foil side
Connect 1 and 4
70
14
A
1
C
B
TKR-850
2
D
E
F
G
I
H
J
K
L
N
M
O
P
Q
S
R
PC BOARD VIEW
TX-RX UNIT (X57-6270-XX) (B/2) -10 : K,E -11 : K2 Component side view
4
D629
C805
C794
C796
C799
C802
C804
C807
C820
C819
C818 C652 R672
C774
R749
R752
R760
R766
R768
R771
R765
C790
C827
C772
C809
C762
+
+ C828
R676 R669 R671
R764
CN606 29 30 NC NC NC NC RXD2 NC TXD2 EMON AI1 EPTT AI2 SC AI3 NC DG TXG TD IO1 TA IO2 RD IO3 RA IO4 RXG IO5 SPM IO6 NC NC 1 2 C788
R742 +
+
J72-0758-01 B/2
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side
12
13
71
R812
+
R750
Component side
Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC601 5B IC624 3G IC630 4N D624 7M IC602 7L IC625 3K D600 4B D625 7N IC605 6L IC627 3B D614 6M D626 4N IC607 8P IC628 3G D618 6N D629 6O IC623 8L IC629 4S D621 7M
11
C663 +
C792
C773
R769
SPG
R755
SPO
R655
1
C681
10
8
1 16
+ C823
CN605
6
IC623
C760 R675
12 D625
R800
L609 C813
L611
L610 C810
R801
C657 R674
R770
4
R756
IC607
8
C649
R796
2
9
C702 +
C812
R788
AO5 AO4 AO3 SPO SPO AO2 AO1 SPI RSI RD SPG SPG 1 D624
C808
9
8
R792
D621
IC602
C691
9
14
CN604
16
R657
14 + C646
9
8 1
R658
8
TXI TXO RXI AC BC1 BC2 BC3 BC4 PTI CLRC RXO PTO 5C GND C765
CN601
C645
C644
1
+
10
C811 +
L608
R785
IC605
R789
C803
R653
6
+
D618
L612
D614
R797
IC601
16
R784
1
C798 +
C814
CN603 C642
VDD OUT
7
SB SB GND GND
DEI
GND
IC629
C816
D626
R612
CP601 DEO
1
5
R654
L613
R603
C795
R793
C613
C623
L604
+ SB
C801 +
D600
L601
C789
C817 +
R751
3.3D
C785
R613
R609
L607
R611
R607
C770
C767
IC625 G I O
C781 R601
C600
+
8C IC630 I G O
ANI
R781
1
CN600 19 20 MIG MIC VLI 5C K4 K5 K2 K3 K1 HK/RXD1 SOE PTT/TXD1 STB1 CLK DAT PSW GND NC SB SB 1 2
C769
C766
C780 C786
IC624 G I O
L606
C800 +
CP600
4
+
R605
+ C826
C825
IC627 I G O
R604
3
O G I IC628
1 C806 +
72
A
B
E
D
C
F
G
H
J
I
K
L
M
O
N
P
Q
S
R
TKR-850
PC BOARD VIEW
2
8C 2 NC SB SB SB SB NC NC GND GND MO MB GND SOE TEMP PSW BUP LD2 FWD STB4 CK DT LDT LDR EPT EPR CP DP NC RSSI ASQ GND NC 35 DET NC 36
C821
+ C722
C692
1
8
R710
C724
5
C710
34
109 108
R645
R648
+ C753
R646
R649
R667
R650
CP602
R615
R814 R634
C638
R619
CP605 CP604
R633 R620
R621 R623
R624
R625
+ C640
R639
IC604
50 51
76 75
R661
CP614
R660
R651
R662
R665
CP619
CP617
CP615
C751 R687
CP618
6
7
R659
CP613
R730 C824 R727
R731
Q604 C735
C737
C716
C727 C738
R712
C719
R704
C714 + C712
IC613
+
5
C641
L602
R647
R638
CP612
R643
1 100
CP608
+ C757
25 26
R618
CP610
R641
C755 R688
R600 R602
4
CP611
R637
+ C756 72 73
CP607
C747
R652
C711
CP606
R631
CP609
R630
+ C754
C752
Q600
R635
C750
R636
S DG
C614
R664
C662
C693 C694 +
R629 R626
R628
R663
R693 C709
C635 C634 C629
L603
C749
C748
R622
CP603
R627
R642
R666
C745
R726
R724
R723
R720
R640
C759
R705
IC616 4
C696
1
8 C616
R614
IC618
X600
R656
CP616
S GD
C734 R733
R679
13
12
8
1
IC603 24
32 L600
R718
8
144
X601
+
1
1
R701
IC611
C726
4
R694
IC612
9
C728
R707 R717
5
1
4
IC600
1
8
+
15
R708
+ C680
24
R698
16
C721
13
C679
12
+
36 37
+
C708
R696
IC614
C704
C690 R684
R713
C705
+
C695
16
C720
C758 +
R681
C670
5 4
IC617
R714
1
C700 +
+ C733
R813
R689
8
C699
R804 C822
1
8
R709
R719
C715
IC615
C742
R697
C707
D601
IC626
R690 C768
C706 +
R695
9
C701
24
C782
C771
C744
G I O
R692
C725
+
C639
R691
+
R722
+
+ C698
+
C723
5 1 R680
C697
+
1
R715
4 3
L605
5 1
IC610 R678
C685
C648
C740
4 3
+
C732
IC606
R644
R735
5
R738
C743 R739
R729 R740
R728 R741
R737 C739
R732 R736
D611
D609
4
R686 R685
C761
C729 +
8
+ C643
C703
R721
D617
D613
R805
R807 R799
1
C741
R606
R683
R670
IC619
C736
R806
R682
C763
D615
R743
D619 D607 R803
D606 R795
C730
+
R808
R798
D622 C776
+
R810
1
C775 +
C746 +
IC608
C731
12
C684
R668
R673
R706
C713 +
R700 R702
C718
C815 R802 C647
R809
D608 R790
R786
R794
D616
R783 R787 R791
R773
IC620
C777 9
8
+
R780 R779
R777
D610
R778
16
D620
R772
R776
C779
R775
D612
R782
D623
Q603 C717
R767
R747 51
R610
R608
D627
R811
R745 C764
IC621
13
R703
Q609 C791
5
R616
R734
C783
Q605 4 3
3
R699
Q611
R815
R744
51
4 3
IC622
+
R753
D628
C778
R762
C602
C605
S
R754
Q606
S DG
1 8C
Q610 G
C797
C793
R774
R758
C787
Q602 Q601
CN602
D
R763
TX-RX UNIT (X57-6270-XX) (B/2) -10 : K,E -11 : K2 Foil side view
C784
1
IC609 1
16
17
9
J72-0758-01 B/2
Component side
Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC600 4O IC611 9E IC618 6L Q601 3J Q610 3D D610 6B D619 6C IC603 9M IC612 7I IC619 6E Q602 3J Q611 4C D611 6D D620 6A IC604 6P IC613 8I IC620 8A Q603 4K D601 6I D612 6A D622 7B IC606 4M IC614 7G IC621 5B Q604 8L D606 7B D613 8B D623 6A IC608 5G IC615 7E IC622 4B Q605 5B D607 7C D615 6C D627 4G IC609 9P IC616 9G IC626 7H Q606 4B D608 6B D616 7A D628 4C IC610 5H IC617 8D Q600 4Q Q609 4D D609 7C D617 8B
10
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side
11
12
13
73
74
14
A
D
TKR-850
2
E
F
G
I
H
J
K
L
O
P
Q
S
R
PC BOARD VIEW
TX-RX UNIT (X57-6270-XX) (B/2) -10 : K,E -11 : K2 Component side view + Foil side
11
12
13
75
76
1 8 + C681 R679
C793
R774
C778
D628
IC622
51
4 3
R744
R815
R7792
R713 R676 R669 R671 R719
C722 + C821
1 C774 16
D613
C763 C761
D616 +
IC620
R749
R752
R760
R766
R768
R771
R751
C730
C827
+ + C729
+
C775
+
R750
C779 1
C792
+
+
C777
NC NC R804 RXD2 NC C790 TXD2 EMON R803 C816 AI1 EPTT SC C812 AI2 D607 NC C809 AI3 R798 TXG DG TD IO1 TAD606 IO2 RD IO3 R794 RA IO4 IO5 C776 RXG D622 SPM IO6 NC R772 NC R765
+
C822
R715
D620 R777
R773
R795
D617
R775
R776
R780 R778
+
8
R783
D623
9
R786
C794
C796
R790 C802
C804
R810 R791 R 787
D612
R782
D608 C807
C820R809
C819
D610 C799
R743
IC621
C762
4
R681
15
R799
+
C692 C652 R672
3 4
D619 C818
R807
D615 R805
D611
CN606 29 30 NC D609 NC 6
R709
R758
C797
G
R732 R736
R737 C739
C744 R742
12 C701 C758
C723
R714
IC611 R812
R808
4 C7605 R675 C788 IC617 R721 R764 C772 8 1
D625
5C663 +
2
4
R710
R763
D Q610
R728 R741
R739
R735 L608
C743
R738
D629
R729 R740
4 R789
R801
L609
R800
C813
L610 C810
+12C823
+
C649
10
R747
C828
C724
IC615
CN605 13 C680 +
Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address Ref No. Address IC600 4E IC607 8P IC614 7M IC621 5R IC628 3G Q604 8H D601 6K D612 6S D619 6Q D626 4N IC601 5B IC608 5M IC615 7O IC622 4R IC629 4S Q605 5R D606 7R D613 8R D620 6S D627 4M IC602 7L IC609 9D IC616 9M IC623 8L IC630 4N Q606 4R D607 7Q D614 6M D621 7M D628 4Q IC603 9G IC610 5L IC617 8P IC624 3G Q600 4C Q609 4P D608 6R D615 6Q D622 7R D629 6O IC604 6D IC611 9O IC618 6H IC625 3K Q601 3J Q610 3P D609 7Q D616 7S D623 6S IC605 6L IC612 7K IC619 6O IC626 6M Q602 3J Q611 4Q D610 6R D617 8R D624 7M IC606 4G IC613 8K IC620 8S IC627 3B Q603 4I D600 4B D611 6P D618 6N D625 7N
10
C805 C740
R788 C648 L612
L613
AO5 AO4 AO3 SPO SPO AO2 AO1 SPI C720 RSI RD SPG C699 SPG
C697
C698 1
R769 R718
Q605
R806
C702 +
+
C764 R745
+
1
IC629
Q606
C773
4
C736
+
R682
5
4
C657 R674
SPG
1 8 IC616 R755
5
+
C704
R707
C798 +
C811 +
1 8 C670 IC607
SB SB GND GND
1 R784
C685 C642 C728
1
24
1
+
R708
C705
SPO
R712
1
R770
R753
C605
C602
D626
R612 R613
R609
R611
R607
16
S
NC 36 NC GND ASQ RSSI NC DP CP EPR EPT LDR LDT DT CK STB4 FWD LD2 BUP PSW TEMP SOE GND MB MO GND GND NC NC SB SB SB SB NC 8C 2 1 8C
35 DET
R610 R678
IC613
14
R733
IC623
R796
C679
C716
16
C719
C712
R701
+ C714
R699
R704
R705 R703
R734
C738
C737
C735
C734
R731
8
+ C700
C715
R686 R685
24
S DG
9
+ C706
Q611
+ C746
C703
1
IC614 D624 8 9 R756
8
CN604
C690 R684
1
Q604
L605
C691
16
13
IC603
+ C646
R727
1 17
9
12
C727
9
8
R767
+
L611
C711
16
SB C791 Q609
IC619
+
D621
C768 R690
IC602
D618
R797
C709
IC626
+
R793
+
C639
C808
72 73
109 108
R670 C803
R717
C756 + R688 C755
+ 16
1
1 5
R785
G I O
9
D614
C726
C748
8
3 4
IC608
R754
R762
R802 C815 C814 +
CN603
C787
+ C783
1
C784
C789
C817 +
R811 C801 +
CP601 C696
TXI TXO R694 RXI AC R696 R698 BC1 BC2 IC612 BC3 51 BC4 43 PTI CLRC RXO PTO 5C GND R689
R673
C643 +
R792
R662
C708
C721
C752
+
1 D601
IC605 C782
C771
C693
C753 +
C695
R695
R655
R667
IC618
8C IC630 I G O
ANI
R781
C647
R668
R680
+
R653 C707
16
R657
R650
+
1 5
1
C662
R646
R692
C725 R658
R649
C757 +
DEO
IC610 3 4
R691
R813
C759
R683
DEI
R697
C747
C800 +
C795
C684
C765
R645
36 37
X601
L600
IC609
C770
+ C713
CN601 8
R648
D627
C718
C824 R730
1
C767 R608
IC625 G I O
C781
C717
R693
R636
144
1
8 32
CP600
R700 R702
R706
R720
R723
R724
C733 +
R601
C766
C769 R726
C745
C732
3.3D
C694
CP606 CP609
C754 +
R687 C751
CP618
C742
Q603
9
CP616
C731
L607
C710
CP613
C750
R631
R643
R663
CP619
C749
R630
R647
R651
CP617
+
24
C741
+
R654
R614
R641
R665
13
IC606 1
L606
C600
O G I IC628
C786 R626
50 51
+
12
+
CN602
S GD
R644
R637
R666
CP615
R659
CP603
R622 R625
R624
R623
R642
R664
C644
CP612
CP614
R660 R656
R628
R639
C645
76 75
IC624 G I O
R814
R633 R621
R620
R634
25 26
IC604
R661
7
R640 L603
1 100
CP611
6
R627
R635
CP610
L602
IC601
C614
C640 +
VDD OUT
8 C616
R652
GND
R616 R606
CP607
C641
1
R629
R602 R600
R638
5
CP608
R603
5
C623
L604 C613
R615
R618
S GD
CP605
L601
C629 C634 C635
Q600 D600
4
IC600
C638
C785
R605
R604
4
CP604
+ C826
X600
R619
C825
IC627 I G O
CP602
3
C780
C806 +
CN600 19 20 MIG MIC VLI 5C K4 K5 K2 K3 K1 HK/RXD1 SOE PTT/TXD1 STB1 CLK DAT PSW GND NC SB SB 1 2
Q601 Q602
14
N
M
R722
1
C
B
J72-0758-01 B/2
Component side Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side Connect 1 and 4
A
B
C
Note : Components marked with a dot (·) are parts of pattern 1.
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
CIRCUIT DIAGRAM
T
TKR-850 1
2
3
4
5
6
7
80
A
TKR-850 1
2
3
4
5
6
7
81
B
C
CIRCUIT DIAGRAM
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
Note : Components marked with a dot (·) are parts of pattern 1.
T
A
B
C
Note : Components marked with a dot (·) are parts of pattern 1.
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
CIRCUIT DIAGRAM
T
TKR-850 1
2
3
4
5
6
7
88
TKR-850
TKR-850 BLOCK DIAGRAM
89
TKR-850
TKR-850 KES-4 (EXTERNAL SPEAKER) When Using an External Speaker 1. Make sure the unit‘s power is tuned off. 2. When using the external speaker, remove the jumper lead from the connector, and attach the speaker cable. 3. When not using the external speaker, replace the jumper lead and insert the connector into the speaker jack (pin9 and 12).
KES-4 UP CK BA
Jumper lead
Connector
15 12 6
13 1
3 Crimp terminal (E23-0613-05)
Speaker cable Black lead
Black/White lead
Specifications Speaker size ........................................... 120mm Maximum input power .......................... 20W Impedance ............................................. 4Ω Frequency response .............................. 100 to 5000Hz Dimensions (W x H x D) ........................ 127 x 127 x 65 mm projection not included 5 x 5 x 2-9/16 inch Weight ................................................... 780g / 1.72 lbs
92
TKR-850 SPECIFICATIONS (K,K2 TYPE) GENERAL Frequency Range ................................ K : 450 to 480MHz
K2 : 480 to 512MHz
Number of Channels ........................... 16 channel Channel Spacing ................................. Wide : 25kHz
Narrow : 12.5kHz
(PLL channel stepping 5kHz/6.25kHz) Operating Voltage ............................... 13.6V DC± 15% Current Drain Standby .......................................... 0.8A Standby w/power save .................. 0.3A (Operationg mode DC-IN : Backup, FAN : Temp, SAVE : ON, DISP : OFF) Receive .......................................... 1.2A Transmit/Receive ........................... Less than 13A Duty Cycle Receive .......................................... 100% Transmit ......................................... 100% (100% @25W) Frequency Stability ............................. Less than ± 0.00015% –30°C to +60°C (–22°F to +140°F) Antenna Impedance ........................... 50Ω Operating Temperature Range ........... –30°C to +60°C (–22°F to +140°F) Dimensions ......................................... 483 (19) W x 88 (3-1/2) H x 340 (13-1/3) D mm (inch) Weight ................................................ 9.7kg (21.4 lbs.)
RECEIVER (Measured by TIA/EIA-603) Sensitivity 12dB SINAD ................................... 0.35µV 20dB Quieting ................................ 0.45µV Selectivity ........................................... Wide : 83dB (± 25kHz)
Narrow : 75dB (12.5kHz)
Intermodulation ................................... Wide : 78dB (± 25kHz/± 50kHz) Hum and Noise ................................... Wide : 50dB
Narrow : 75dB (± 12.5kHz/±25kHz)
Narrow : 45dB
Spurious & Image Rejection ............... 90dB Audio Output (Ext. Speaker) ............... 4W at 4Ω less than 5% distortion Audio Distortion (Ext. Speaker) .......... Less than 2.5% at 1000Hz Band Spread ....................................... 5MHz
TRANSMITTER (Measured by TIA/EIA-603) RF Power Output ................................ 40W adjustable to 25W (100% duty @25W) Type of Emission ................................ Wide : 16K0F3E
Narrow : 11K0F3E
Spurious Response ............................. Harmonics : 80dB FM Hum and Noise ............................ Wide : 50dB
Others : 75dB
Narrow : 45dB
Audio Distortion .................................. Less than 3% at 1000Hz Microphone Impedance ...................... 600Ω Band Spread ....................................... K : 30MHz
K2 : 32MHz
93
TKR-850 SPECIFICATIONS (E TYPE) GENERAL Frequency Range ........................................ Number of Channels .................................. Channel Spacing ......................................... Operating Voltage ....................................... Current Drain Standby ................................................... Standby w/power save ........................... Receive ................................................... Transmit/Receive .................................... Duty Cycle .................................................. Frequency Stability ..................................... Antenna Impedance ................................... Operating Temperature Range ................... Dimensions ................................................. Weight ........................................................
440 to 470MHz 16 channel Wide : 25kHz 13.2V DC
Narrow : 12.5kHz (PLL channel stepping 5kHz/6.25kHz)
0.8A 0.3A (Operationg mode DC-IN : Backup, FAN : Temp, SAVE : ON, DISP : OFF) 1.2A Less than 13A Receive : 100% Transmit : 100% (100% @25W) Less than ± 0.00015% –30°C to +60°C 50Ω –30°C to +60°C 483 W x 88 H x 340 D mm 9.7kg
RECEIVER (Measured by ETS 300 086) Sensitivity ................................................... Adjucent Channel Selectivity ..................... Intermodulation .......................................... Spurious & Image Rejection ....................... Audio Output (Ext. Speaker)....................... Audio Distortion (Ext. Speaker) .................. Band Spread ...............................................
0.45µV 83dB (± 25kHz) 75dB (± 12.5kHz) 72dB 90dB 4W at 4Ω less than 5% distortion Less than 2.5% at 1000Hz 5MHz
TRANSMITTER (Measured by ETS 300 086) RF Power Output ........................................ Modulation Limiting .................................... Spurious Emission ...................................... FM Noise (EIA) ........................................... Modulation Distortion ................................. Microphone Impedance ............................. Band Spread ...............................................
40W adjustable to 25W (100% duty @25W) ± 5kHz at ± 25kHz ±2.5kHz at ± 12.5kHz –36dBm ≤ 1GHz –30dBm > 1GHz 25kHz : 50dB 12.5kHz : 45dB Less than 3% at 1000Hz 600Ω 30MHz
KENWOOD CORPORATION 14-6, Dogenzaka 1-chome, Shibuya-ku, Tokyo 150-8501, Japan
KENWOOD SERVICE CORPORATION P.O. BOX 22745, 2201 East Dominguez Street, Long Beach, CA 90801-5745, U.S.A.
KENWOOD ELECTRONICS CANADA INC. 6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8
KENWOOD ELECTRONICS DEUTSCHLAND GMBH Rembrücker Str. 15, 63150 Heusenstamm, Germany
KENWOOD ELECTRONICS BELGIUM N.V. Mechelsesteenweg 418 B-1930 Zaventem, Belgium
KENWOOD ELECTRONICS FRANCE S.A. 13, Boulevard Ney, 75018 Paris, France
KENWOOD ELECTRONICS U.K. LIMITED KENWOOD House, Dwight Road, Watford, Herts., WD1 8EB United Kingdom
KENWOOD ELECTRONICS EUROPE B.V. Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands
KENWOOD ELECTRONICS ITALIA S.p.A. Via G. Sirtori, 7/9 20129 Milano, Italy
KENWOOD IBERICA S.A. Bolivia, 239-08020 Barcelona, Spain
KENWOOD ELECTRONICS AUSTRALIA PTY. LTD. (A.C.N. 001 499 074) 16 Giffnock Avenue, Centrecourt Estate, North Ryde, N.S.W. 2113 Australia
KENWOOD ELECTRONICS (HONG KONG) LTD. Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Kwai Fong, N.T., Hong Kong
KENWOOD ELECTRONICS TECHNOLOGIES(S) PTE LTD. Sales Marketing Division 1 Ang Mo Kio Street 63, Singapore 569110
