Preview only show first 10 pages with watermark. For full document please download

Keyscan Proximity Reader/keypad

Rating
Date

November 2018
Size

1.1MB
Views

1,703
Categories

Home Home security & automation Access cards

Transcript

K-KPR Keyscan Proximity Reader/Keypad • Occupies one reader port on Keyscan Systems • May be used on non-Keyscan systems with many HID 125kHz card protocols • Suitable for outdoor use in all weather conditions • Keypad labeled with alpha-numeric identifiers • Pass-thru Wiegand output standard • Pin entry outputs an 8-bit burst • Epoxy encased electronics provide reliable operation • Convenient mounting to a single gang wall box • Buttons provide audible feedback • Blue backlighting for easy use in low light areas • Provides read range of up to 15.2cm (6 inches) • Raised ‘pip’ on the 5 key for visually impaired individuals • Limited lifetime warranty against defects in materials and workmanship www.keyscan.ca K-KPR Keyscan Proximity Reader/Keypad FE AT URES A N D B E N E F I T S • Ideal for applications that require enhanced security by enforcing both card presentation and PIN entry for secured areas • For applications where cards are not issued, users may be assigned a temporary or permanent PIN with designated access privileges • Mounts on a single gang electrical box • Membrane style keypad surface prevents malfunction due to dust and debris accumulation • Keypad surface does not leave finger print smudges SPECI F I CATI ON S Size: 4.6 x 3 x 0.7 inches (117 x 77 x 18mm) Read Range: Off metal – up to 6” (15.2cm) On metal – up to 4” (10.2cm) Input Voltage: 12VDC at Reader Current Draw: 115mA Operating Temperature: -40ºC to 65ºC (-40ºF to 149ºF) Cable: 6 conductor shielded cable Wiegand Output: 500 feet (152 meters) KEYSCAN INC. 901 Burns Street East, Whitby, Ontario L1N 6A6 Keyscan Inc. reserves the right to alter designs and specifications without notice or obligation Phone: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 www.keyscan.ca Rev.:04-2010 K-PROX2 Keyscan Proximity Reader K-PROX2 • Simple 2 in 1 unit; mullion or single gang electrical box applications • Discard removable switch plate for mullion installations • Compatible with HID proximity cards and tags over a range of Wiegand protocols • Electronics secured in tamper-resistant epoxy potting for added protection • Install on any surface including single gang wall switch • Durable, weather-resistant construction for reliable operation and long usage even in harsh environments • Limited lifetime warranty against defects in materials and workmanship www.keyscan.ca K-PROX Keyscan Proximity Reader K-PROX2 Keyscan Proximity Reader Fe at ures and B e n e f i t s • • • • • Uses proven digital radio frequency identification technology Includes ABS wall witch plate HID compatible over a wide range of Wiegand protocols Designed for indoor and outdoor environments Unique and versatile design for easy installation Spe c i f i c at i o n s Size • Mullion - 4.5” (11.43 cm) x 1.5” (3.8 cm) x 0.62” (1.6 cm) • Switch Plate – 4.5” (11.43 cm) x 3” (7.62 cm) x 0.62” (1.6 cm)) Read Range • Off metal - up to 6” (15.2 cm) • On metal - up to 4” (10.2 cm) Input Voltage • 12VDC at reader Typical Current Draw • Nominal draw is 40 mA • Maximum draw is 80 mA during card read Operating Temperature • - 40º C to 65º C (- 40º F to 149º F) Cable Distance • 12” wire pigtail standard • Wiegand interface 500 feet (152 metres) 6 conductor shielded 22 AWG Indoor/Outdoor Design • Secured in a rugged, tamper-resistant epoxy potting designed to withstand harsh weather conditions • Easily installed in any location Certifications • IC (Industry Canada), FCC, CE KEYSCAN INC. 901 Burns Street East Whitby, Ontario, Canada L1N 6A6 Telephone: 905-430-7226 Facsimile: 905-430-7275 Toll Free: 1-888-539-7226 (Canada/USA) Web: www.keyscan.ca K-PROX2 Want more information? Contact your local representative at: RF RECEIVER RF FOBS WITH PROXIMITY CHIP K-RX (RF Receiver), K-TX2 (RF Fob with HID chip), K-INTX2 (RF Fob with INDALA chip) • K-TX2: 4 button RF wireless transmitter with 125kHz proximity coil • K-INTX2: 4 button RF wireless transmitter with matching Indala proximity coil • K-STX2-1K: 4 button RF transmitter with matching K-SECURE1K coil • K-STX2-4K: 4 button RF transmitter with matching K-SECURE4K coil • Combines the convenience of a long range radio frequency fob with an onboard proximity chip for use at proximity HID 125kHz (K-TX2) or INDALA (K-INTX2) readers . • Receiver is contained in a weather resistant NEMA enclosure and is suitable for outdoor installations. • Ideal for security access control applications such as securing garage or gate entries and/or exits. • Receiver provides two hardwired 36bit Keyscan secure Wiegand outputs for connection to Keyscan’s family of access control units (ACUs). Two Wiegand outputs provide an ideal solution for multiple gate control using a single receiver. • Transmitters offer four-buttons, and are designed to support multiple gate and multiple receiver installations. • Receiver offers innovative RF sensitivity and range control. Range may be adjusted from 12" (0.3m) to a factory defaulted maximum of 150' (45.7m). • RF operation uses an ultra high 433Mhz Frequency. • Employs a rolling 40 bit code combined with a 256 bit key for encrypted anti-sniffing and anti-playback protection. • Rugged long life transmitters tested to over 35,000 button presses. www.keyscan.ca RF RECEIVER RF FOBS WITH PROXIMITY CHIP K-RX (RF Receiver), K-TX2 (RF Fob with HID chip), K-INTX2 (RF Fob with INDALA chip) FEATURES A N D B E N E F I T S • Fast installation with Keyscan Access Control Unit. Simple fob enrollment in Keyscan software. One cardholder number for both RF activations and proximity activations • Allows for integration to gate or garage applications without costly trenching or installation of pedestals to mount readers. • Permits tracking, usage reporting and assigning access privileges (including time and day restrictions) when used with Keyscan access control units and software. • Fobs work in long range RF mode as well as standard proximity format for other access control secure doors. • Fobs may be ordered with HID 125kHz K-TX2 or INDALA (K-INTX2) proximity chip sets. • A standalone mode with TTL driven relay output is available for use without access control integration. A PPL I CATI O N S % &% % ' % &% % ' !"# $ S PECI F I CATI O N S MODEL #: INPUT POWER: RF INPUT SIGNAL: COMM FORMAT: DIMENSIONS: OPERATING TEMP: K-RX 10 to 24 VDC @ 80mA (nominal) 433Mhz Wiegand 36 bit hardwired digital output 6 5/16" x 3 1/2" x 2 3/8 Inches 16.0 x 9.0 x 6.1 cm -22°C to 50°C -7°F to 122°F MODEL #: ENCODING: OPERATING TEMP: CASE MATERIAL: POWER REQ: OUTPUT: KEYSCAN INC. 901 Burns Street East, Whitby, Ontario L1N 6A6 K-TX2 (HID Prox), K-INTX2 (INDALA) Code Hopping with 256 bit encryption -22°C to 50°C -7°F to 122°F High Density Plastic Water Resistant Keypad Membrane 27A, NM27 sized 12Volt alkaline battery Field replaceable RF: 433MHz UHF Proximity: 125khz Keyscan Inc. reserves the right to alter designs and specifications without notice or obligation Phone: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 www.keyscan.ca Rev.:10-2010 K-SMART Contactless Smartcard Reader for Access Control UÊ 1ÃiÃÊÌiÀ>Ì>ÞÊ>VV>i`Êv>ÀiÊVÌ>VÌiÃÃÊÃ>ÀÌV>À`Ê ÌiV}Þ UÊ -,/ÊÃÕ««ÀÌÃÊiÞÃV>½ÃÊ- 1, ÊVÌ>VÌiÃÃÊv>ÀiÊ Ã>ÀÌV>À`Ã UÊ /iÊ- 1, Êv>ÀiÊVÀi`iÌ>Ê«ÀÛ`iÃÊ>ÌVÕÌiÀviÌ}Ê «ÀÌiVÌÊÕÃ}ÊiÞÃV>½ÃÊ>ÝÊ-iVÕÀiÊiVÀÞ«ÌÊÌiV}ÞÊ Ê¼ÛiÀÊÌiÊ>À½ÊÌÀ>ÃÃÃÊLiÌÜiiÊÌiÊÀi>`iÀÊ>`ÊV>À` UÊ -Õ««ÀÌÃÊ-"Ê£{{{ÎÊv>ÀiÊVÌ>VÌiÃÃÊ«À«ÀiÌ>ÀÞÊ VÌ>VÌiÃÃÊÃ>ÀÌV>À`Ã]ÊV>À`ÊÃiÀ>ÊÕLiÀÊ - ®ÊÞ UÊ *ÀÛ`iÃÊ>ÊÛ>ÌÛiÊ¼i>ÀÌLi>Ì½ÊÌiV}ÞÊvÊÌÃÊ i>ÀÌLi>ÌÊÃÊÌiÀÀÕ«Ìi`Ê`ÕiÊÌÊÜÀ}Êv>ÕÌÊÀÊÀi>`iÀÊ `>>}iÊ>Ê>>ÀÊV`ÌÊÃÊÌÀ}}iÀi`ÊLÞÊÌiÊiÞÃV>Ê VÌÀÊ«>i UÊ "vviÀÃÊ¼Ì/>«iÀ½ÊV>«>LÌÞÊÜÌÊ>Ê`i>iÀÊÃÌ>i`Ê>`Ê ÃÕ««i`Ê>ÌÌ>«iÀÊÃÜÌVÊvÀÊvÕÀÌiÀÊi>Vi`ÊÃiVÕÀÌÞ UÊ -,/£ÓxÊÛiÀÃÊvviÀÃÊ>Ê}À>ÌÊ«>ÌÊvÀÊ Ê £ÓxâÊ«ÀÝÊV>À`ÃÊÌÊ}ÊÃiVÕÀÌÞÊv>ÀiÊÌiV}ÞÊ VÀi`iÌ>Ã UÊ -,/"6ÊÛiÀÃÊÃÊ>Ê1-ÊÛiÀiÌÊ*-ÊÓä£ÊEÊ/7 Ê VÀi`iÌ>ÊV«>ÌLiÊÀi>`iÀ UÊ -«iÊÓÊÊ£ÊÕÌÊÌÊÃÕ««ÀÌÊLÌÊÕÊÀÊÃ}iÊ}>}Ê iiVÌÀV>ÊLÝÊ>««V>ÌÃ° UÊ iVÌÀVÃÊ>ÀiÊÃiVÕÀi`ÊÊÌ>«iÀÀiÃÃÌ>ÌÊi«ÝÞÊ«ÌÌ}ÊvÀÊ >``i`Ê«ÀÌiVÌ° UÊ ÕÀ>LiÊ`iÃ}Ê«ÀÛ`iÃÊÜi>ÌiÀÀiÃÃÌ>ÌÊVÃÌÀÕVÌÊ vÀÊÀi>LiÊ«iÀ>ÌÊ>`Ê}ÊÕÃ>}iÊiÛiÊÊ>ÀÃÊ iÛÀiÌÃ° UÊ iÛiÀi`ÊÜÌÊiÞÃV>½ÃÊÌi`ÊviÌiÊÜ>ÀÀ>ÌÞÊ>}>ÃÌÊ `iviVÌÃÊÊ>ÌiÀ>ÃÊ>`ÊÜÀ>Ã«° www.keyscan.ca -,/ -, K-SMART Contactless Smartcard Reader for Access Control Fe at ures and B e n e f i t s UÊ 1ÃiÃÊ`ÕÃÌÀÞÊ«ÀÛiÊ«À«ÀiÌ>ÀÞÊ, ÊÃ>ÀÌV>À`ÊÌiV}Þ° UÊ - 1, Ê*ÀÛ`iÃÊVÀi`iÌ>Ê>ÌVÕÌiÀviÌ}Ê«ÀÌiVÌ° UÊ 6iÀÃ>ÌiÊÀi>`iÀÊ`iÃ}ÊÃÕÌ>LiÊvÀÊLÌÊÕÊ>`ÊÃ}iÊ}>}Ê «>ÌiÊÃÌ>>Ì° UÊ iÃ}i`Ê>`Ê }iiÀi`ÊÜÌÊ 9- ÊÀi>LÌÞÊ>`ÊµÕ>ÌÞ° UÊ }À>ÌÊ«ÌÊ>Û>>LiÊvÀÊÃÜ>««}Ê Ê£ÓxâÊVÀi`iÌ>ÃÊÌÊ ÃiVÕÀiÊv>ÀiÊVÀi`iÌ>ÊVÛiÀÃÃ°I UÊ 1-ÊÛiÀiÌÊ«ÌÊ>Û>>LiÊvÀÊ*-ÊÓä£Ê>`Ê/7 ÊV«>ÌLiÊ ÌÀ>Ã«>ÀiÌÊÀi>`iÀ°ÊI IÊ-iiÊÀ`iÀ}Ê«ÌÃ Spe c i f i c at i o n s -âi Ê UÊÕÊÊ{°x»Ê££°{ÎÊV®ÊÝÊ£°x»ÊÎ°nÊV®ÊÝÊä°ÈÓ»Ê £°ÈÊV® Ê UÊ-ÜÌVÊ*>ÌiÊqÊ{°x»Ê££°{ÎÊV®ÊÝÊÎ»ÊÇ°ÈÓÊV®ÊÝÊ ä°ÈÓ»Ê£°ÈÊV® ,i>`Ê,>}i Ê UÊ"vvÊiÌ>ÊÊÕ«ÊÌÊÓ»Êx°£ÊV® «ÕÌÊ6Ì>}i Ê UÊ£Ó6 Ê>ÌÊÀi>`iÀ /Þ«V>Ê ÕÀÀiÌÊ À>Ü Ê UÊ£{äÊ>ÛiÀ>}i "«iÀ>Ì}Ê/i«iÀ>ÌÕÀi Ê UÊÊ{ä¨Ê ÊÌÊÈx¨Ê ÊÊ{ä¨ÊÊÌÊ£{¨Ê® >LiÊ ÃÌ>Vi Ê UÊ£Ó»ÊÜÀiÊ«}Ì>ÊÃÌ>`>À` Ê UÊ7i}>`ÊÌiÀv>ViÊxääÊviiÌÊ£xÓÊiÌiÀÃ®Ê Ê ÊÊÊÊÈÊV`ÕVÌÀÊÃi`i`ÊÓÓÊ7 `ÀÉ"ÕÌ`ÀÊ iÃ} Ê UÊ-iVÕÀi`ÊÊ>ÊÀÕ}}i`]ÊÌ>«iÀÀiÃÃÌ>ÌÊi«ÝÞÊ «ÌÌ}Ê`iÃ}i`Ê Ê ÊÊÊÌÊÜÌÃÌ>`Ê>ÀÃÊÜi>ÌiÀÊV`ÌÃ Ê UÊ >ÃÞÊÃÌ>i`ÊÊ>ÞÊV>Ì O rd er i ng O p t i o n s -,/Ê -,/£ÓxÊ -,/"6Ê Ài`iÌ>Ã - 1, Ê £Î°xÈâÊ Ì>VÌiÃÃÊv>ÀiÊ,i>`iÀ]ÊÀi>`ÃÊÃiVÕÀiÊÃiVÌÀÊÊiÞÃV>Êv>ÀiÊVÀi`iÌ>Ã]ÊÊ - ÊÊÌiÀÃ° Ê£ÓxâÊÌÊv>ÀiÊVÀi`iÌ>Ê}À>ÌÊÀi>`iÀ°Ê->iÊ>ÃÊ-,/ÊÜÌÊ>``i`Ê Ê V«>ÌLiÊ£ÓxâÊ*,"8ÊVÀi`iÌ>ÊÀi>`ÊV>«>LÌÞ° 1-ÊÛiÀiÌÊ>««ÀÛi`Ê*-ÊÓä£ÊEÊ/7 ÊÌÀ>Ã«>ÀiÌÊÀi>`iÀ°Ê-Õ««ÀÌÃÊ*6ÊÌÞ«iÃÊÉ ]Ê/7 Ê /Þ«iÃÊÉ £Î°xÈâÊ Ì>VÌiÃÃÊ-"Ê*ÀÌ>LiÊv>ÀiÊÃ>ÀÌV>À`ÊÜÌÊLÕÌÊ>ÝÊ-iVÕÀiÊiVÀÞ«ÌÊ ÌiV}ÞÊvÀÊ>`Û>Vi`ÊVÀi`iÌ>ÊÃiVÕÀÌÞ°Ê*>V>}iÊvÊvvÌÞÊxä®ÊV>À`Ã° KEYSCAN INC. ä£Ê ÕÀÃÊ-ÌÀiiÌÊ >ÃÌ 7ÌLÞ]Ê"Ì>À]Ê >>`>ÊÊ£ ÊÈÈ /ii«i\Êäx{ÎäÇÓÓÈÊÊ>VÃi\Êäx{ÎäÇÓÇx /ÊÀii\Ê£nnnxÎÇÓÓÈÊ >>`>É1-® 7iL\ÊÜÜÜ°iÞÃV>°V> Rev.:03-28-2008 7>ÌÊÀiÊvÀ>Ì¶Ê Ì>VÌÊÞÕÀÊV>ÊÀi«ÀiÃiÌ>ÌÛiÊ>Ì\ K-VAN Keyscan Vandal Resistant Proximity Reader • Ideal proximity reader for applications where crime and vandalism are expected • Solid stainless steel bezel with Fibertex® insert provides the highest level of vandal resistance • Fibertex® material is UL752 listed for bulletproof integrity • May be used on non-Keyscan systems with many HID 125kHz card protocols • Pass-thru Wiegand output standard • Suitable for outdoor applications in all weather conditions • Provides non-contact read range of up to 25mm (1 inch) • Limited lifetime warranty against defects in materials and workmanship www.keyscan.ca K-PROX Keyscan Proximity Reader K-VAN Keyscan Vandal Resistant Proximity Reader Fe at ures and B e n e f i t s • Stylish yet extremely robust for the toughest applications • Uses proven digital radio frequency identification technology • Ideal proximity reader where vandalism is a concern • Designed for indoor and outdoor environments • Pass-thru Wiegand output for easy integration into existing access control systems • Mounting options include two countersunk 0.25 inch thru-holes as well as four 1/4-20 tapped holes in the back for tamper-proof blind mount installations. • Keypad surface does not leave finger print smudges Spe c i f i c at i o n s Size: 5.25 x 2 x 0.75 inches (134 x 51 x 19mm) Read Range: Up to 1 Inch (25mm) Input Voltage: 12 VDC at reader Typical Current Draw: 90mA "( Cable Termination: 6 conductor shielded 12” Pigtail standard Wiegand Output: 500 feet (152 meters) Operating Temp: -40ºC to 65ºC (-40ºF to 149ºF) KEYSCAN INC. 901 Burns Street East Whitby, Ontario, Canada L1N 6A6 Telephone: 905-430-7226 Facsimile: 905-430-7275 Toll Free: 1-888-539-7226 (Canada/USA) Web: www.keyscan.ca Want more information? Contact your local representative at: RF TRANSMITTERS WITH PROXIMITY CHIP TX4PRX (HID Prox), INTX2PRX,INTX4PRX (Indala Prox) RXPROX TX4PRX • Now combines two technologies in one simple Key Fob. • Keyscan's TX4PRX is a four button RF transmitter that comes complete with an encoded HID proximity chip. Also available with an Indala proximity chip. • Acts as a regular HID proximity tag on HID readers or INDALA proximity tag on INDALA readers. • Keyscan’s RXPROX is the RF receiver that transmits a Wiegand output to a Keyscan Access Control Unit. • Ideal for a parking gate or garage applications when mixed with HID or INDALA proximity readers throughout the rest of the building. • Fast, easy, trouble-free installation to add RF transmitters and receivers to your Keyscan Access Control System. www.keyscan.ca RF TRANSMITTERS WITH PROXIMITY CHIP TX4PRX (HID Prox), INTX2PRX,INTX4PRX (Indala Prox) FEATURES A N D B E N E F I T S • Fast easy installation to a Keyscan Access Control Unit. • Fast easy setup on the Keyscan Software. One cardholder number entry for both the RF signal and HID, HID iClass or Indala proximity. • Save time and money by using RF. No more trenching or installing pedestals to mount readers. • The TX4PRX is a 4 button transmitter complete with an HID proximity chip. The INTX2PRX & INTX4PRX have the Indala proximity chip. • The RXPROX can be configured to activate only the buttons you choose. E.g. You can set the RXPROX to accept only RF information from the top right button on the TX4PRX to unlock the parking gate and all other buttons are non functional. Setup one of the other buttons to activate another RXPROX at a different gate and a third button for a panic alarm • Simplifies both installation and maintenance procedures. A PPL I CATI O N S Use HID, or Indala readers for doors S PECI F I CATI O N S MODEL #: INPUT POWER: RF INPUT SIGNAL: COMM FORMAT: RELAY CONTACTS: TRANSIENT: DIMENSIONS: OPERATING TEMP: RXPROX 10 to 14 VDC @ 35mA Standard 433Mhz Op.315MhzC Wiegand 36 bit Digit Op. 2 Class “C” 30V @ 3A Max Spark Gap on all Terminals Protection: Diode & MOV’s 5.1 x 5.1 x 2 3/4 Inches 0°C / -32°F to 50°C / 132°F KEYSCAN INC. 901 Burns Street East, Whitby, Ontario L1N 6A6 MODEL #: ENCODING: OPERATING TEMP: CASE MATERIAL: TX4PRX Code Hopping -25 TO +50° C High Density Plastic Water Resistant Keypad Membrane EMBEDDED: HID Proximity(TX4PRX) INDALA Proximity (INTX2PRX or INTX4PRX) POWER REQ: Internal Lithium Battery with low Battery Detection OUTPUT: RF Signal 433 MHz/315MHz SIL AM Superhet TYPICAL READING RANGE: Up to 30m (100ft) Keyscan Inc. reserves the right to alter designs and specifications without notice or obligation Phone: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 www.keyscan.ca Rev.:08-2010 Search-Gate Tokenless Biometric Reader UÊ -i>ÀV>ÌiÊÃÊ>Ê£\>ÞÊLiÌÀVÊÀi>`iÀ UÊ "vviÀÃÊ«Ì>ÊÌÜv>VÌÀÊÛiÀvV>ÌÊÜiÊVLi`ÊÜÌÊ>ÊiÝÌiÀ>Ê7i}>`ÊÀi>`iÀ UÊ *ÀÛ`iÃÊÌiÊ}iÃÌÊiÛiÊvÊv}iÀ«ÀÌÊLiÌÀVÊ«iÀvÀ>ViÊ>`Ê>VVÕÀ>VÞ UÊ -ÌÀiÃÊÕ«ÊÌÊ£]ÓääÊv}iÀ«ÀÌÊÌi«>ÌiÃÊÊÌiÊ`iÛViÊVv}ÕÀ>LiÊvÀÊÃiÀÛiÀÊL>Ãi`ÊÊ v}iÀ«ÀÌÊV«>ÀÃÃÊvÀÊÃÞÃÌiÊÃV>>LÌÞ UÊ >«>LiÊvÊÃi>ÀV}Ê£]ÓääÊÌi«>ÌiÃÊ>ÌÊ>ÊÀ>ÌiÊvÊxääÊÌi«>ÌiÃÊ«iÀÊÃiV` UÊ ÕÃÌâ>LiÊ7i}>`ÊÕÌ«ÕÌÊÕ«ÊÌÊ£ÓnÊLÌÃ°Ê`i>ÊvÀÊÌi}À>ÌÊÜÌÊ>ÞÊÊ >VViÃÃÊVÌÀÊÃÞÃÌi www.keyscan.ca Search-Gate Tokenless Biometric Reader FEATURES A N D B E N E F I T S UÊ *ÜiÀi`ÊLÞÊ }iÌÊ-ÞÃÌiÃÊ-iVÕÀ- ÊV«Ê>`Ê«ÀiiiÌÊ>ÌV}Ê>}ÀÌÊ>ÃÊiÃÌ>LÃi`ÊLÞÊÌiÊ >Ì>ÊÃÌÌÕÌiÊvÊ -Ì>`>À`ÃÊ>`Ê/iV}Þ® UÊ `i>ÊvÀÊÕÃiÊÜÌÊ>ÞÊ>VViÃÃÊVÌÀÊÃÞÃÌi UÊ "L>À`ÊÀi>ÞÊÃÕÌ>LiÊvÀÊÃ}iÊ`ÀÊÊÃÌ>`>iÊ>««V>ÌÃ UÊ iÃÊV«iÌiÊÜÌÊ-iVÕÀ-iÌÕ«ÒÊÃvÌÜ>Ài SPECI F I CATIO N S Fingerprint Sensor Silicon sensor (500 dpi) Enrollment Method Single ﬁnger, multiple enrollments Extraction & ID Time ~ 1.5 seconds FRR FRR 0.1 % - 0.001% FAR FAR 0.01% - 0.001% Security Level Conﬁgurable Allowable Finger Rotation +/- 15º Template Size 748 bytes Template Storage 1,200 templates I/O Interface RS232, RS485 Baud Rate 9600 –115 Kbps programmable Ethernet 10/100 Wiegand I/O Programmable up to 128 bits DC Power 6 - 12V DC standard input (12 - 48V DC jumper setup) Power-over-Ethernet (PoE) Fully 802.3af compliant; 12~60V DC (jumper setting) for non 802.3af standard Current Standby: 200 ma @ 12V, Operational: 280 ma @ 12V Operating Temperature 0 to 55 ºC (32 to 121 ºF) Physical Dimensions 5.42” x 3.14” x 2.28” (137.7 mm x 79.7 mm x 57.9 mm) Weight 0.9 ounces (0.3 kg) KEYSCAN INC. ä£Ê ÕÀÃÊ-ÌÀiiÌÊ >ÃÌ 7ÌLÞ]Ê"Ì>ÀÊ£ ÊÈÈ *i\Êäx°{Îä°ÇÓÓÈÊÊ/ÊÀii\Ê£°nnn°xÎ°ÇÓÓÈÊ>Ý\Êäx°{Îä°ÇÓÇx ÜÜÜ°iÞÃV>°V> Rev.:03-09 7>ÌÊÀiÊvÀ>Ì¶Ê Ì>VÌÊÞÕÀÊV>ÊÀi«ÀiÃiÌ>ÌÛiÊ>Ì\ Smart-Gate 1:1 Biometric Reader with contactless Mifare Smartcard Reader UÊ ->ÀÌ>ÌiÊÃÊ>Ê£\£ÊLiÌÀVÊÀi>`iÀÊ UÊ *ÀÛ`iÃÊÃÌ>ÌiÊvÊÌiÊ>ÀÌÊÌÜÊv>VÌÀÊÛiÀvV>Ì UÊ ->ÀÌ>ÌiÊ«ÀÛ`iÃÊÌiÊ}iÃÌÊiÛiÊvÊv}iÀ«ÀÌÊLiÌÀVÊ«iÀvÀ>ViÊ>`Ê>VVÕÀ>VÞ° UÊ iÌÀVÊÌi«>ÌiÃÊ>ÀiÊÃÌÀi`ÊÊ>Êv>ÀiÊVÌ>VÌiÃÃÊÃ>ÀÌV>À`Ê>`ÊÌÊ>ÊiÌÜÀÊ`>Ì>L>Ãi]ÊÊ ÕÃiÀÃÊ>ÀiÊ>ÃÃÕÀi`ÊÌ>ÌÊÌiÀÊLÊ`iÌÌÞÊÀi>ÃÊÃiVÕÀiÞÊÊÌiÀÊ«ÃÃiÃÃÊ>ÌÊ>ÊÌiÃ°Ê UÊ "vviÀÃÊvÕÊ >ÃÞÊ-Ìi«ÒÊÌi}À>ÌÊÜÌÊiÞÃV>ÊVViÃÃÊ ÌÀÊ-ÞÃÌiÃÊÜiÊÕÃi`ÊÜÌÊÊ iÞÃV>½ÃÊ- 1, Ê£ÊVÀi`iÌ>ÊvÀÊÃ}iÊv}iÀÊiÀiÌÊ>`ÊÌiÊ- 1, Ê{ÊÊ VÀi`iÌ>ÊvÀÊÌÜÊv}iÀÊiÀiÌ° UÊ ÕÃÌâ>LiÊ7i}>`ÊÕÌ«ÕÌÊÕ«ÊÌÊ£ÓnÊLÌÃ°Ê`i>ÊvÀÊÌi}À>ÌÊÜÌÊ>ÞÊÊ >VViÃÃÊVÌÀÊÃÞÃÌiÊÊÊÊ www.keyscan.ca Smart-Gate 1:1 Biometric Reader with contactless Mifare Smartcard Reader FEATURES A N D B E N E F I T S UÊ *ÜiÀi`ÊLÞÊ }iÌÊ-ÞÃÌiÃÊ-iVÕÀ- ÊV«Ê>`Ê«ÀiiiÌÊ>ÌV}Ê>}ÀÌÊ>ÃÊiÃÌ>LÃi`ÊLÞÊÌiÊ >Ì>ÊÃÌÌÕÌiÊvÊ -Ì>`>À`ÃÊ>`Ê/iV}Þ® UÊ "vviÀÃÊÌÀiiÊ`iÃÊvÊ"«iÀ>Ì\Ê Ê Ê Ê Ê UÊ iÞÃV>ÊÌi}À>Ìi`Ê`i\Ê1ÃiÃÊ- 1, Ê -ÊiVÀÞ«Ìi`Êv>ÀiÊVÌ>VÌiÃÃÊÃ>ÀÌV>À`ÃÊÜÌÊ >ÃÞÊ-Ìi«ÒÊÃ}iÊÊ Ê Ê ÃvÌÜ>ÀiÊV>À`ÊiÀiÌÊÜÌÊ¼LÊ>ÌÊÌiÊÀi>`iÀ½ÊiÀiÌÊÌiV}Þ°Ê Ê UÊ *>ÃÃÌÀÕ}Ê`i\Ê iVÌÊ>ÞÊ>Õv>VÌÕÀiÀÃÊ«À«ÀiÌ>ÀÞÊÀi>`iÀÊÌÊÌiÊ->ÀÌ>ÌiÃÊ7i}>`Ê«ÕÌ°Ê1«ÊLÊÊ Ê Ê Ìi«>ÌiÊÛ>`>ÌÊÌiÊ->ÀÌ>ÌiÊ«>ÃÃiÃÊÌÀÕ}ÊÌiÊÀiViÛi`Ê7i}>`°ÊIÊÊ Ê UÊ }iÌÊ-Ì>`>À`Ê`i\Ê ÊÌi«>ÌiÊÃÊÃÌÀi`ÊÊ>Ê-iVÕÀiÊÀÊv>ÀiÊVÌ>VÌiÃÃÊÃ>ÀÌV>À`ÊÜÌÊÛiÀÃ>ÌiÊ>`ÊÊÊ Ê vÕÞÊVÕÃÌâ>LiÊ7i}>`ÊÕÌ«ÕÌ°Ê UÊ `i>ÊvÀÊÕÃiÊÊÌiÀÊ>VViÃÃÊVÌÀÊÃÞÃÌiÃ UÊ "L>À`ÊÀi>ÞÊÃÕÌ>LiÊvÀÊÃ}iÊ`ÀÊÊÃÌ>`>iÊ>««V>ÌÃ UÊ iÃÊV«iÌiÊÜÌÊ-iVÕÀ-iÌÕ«ÒÊÃvÌÜ>Ài *Bio Validation requires K-Secure or Mifare Credentials to store the individuals bio template. SPECI F I CATIO N S Fingerprint Sensor Silicon sensor (500 dpi) Enrollment Method Single ﬁnger, multiple enrollments Extraction & ID Time ~ 1.5 seconds FRR FRR 0.1 % - 0.001% FAR FAR 0.01% - 0.001% Security Level Conﬁgurable Allowable Finger Rotation +/- 15º Template Size 748 bytes Template Storage 1,200 templates I/O Interface RS232, RS485 Baud Rate 9600 –115 Kbps programmable Ethernet 10/100 MIFARE® Cards 14443 A and K-Secure Wiegand I/O Programmable up to 128 bits DC Power 6 - 12V DC standard input (12 - 48V CC jumper setup) Fully 802.3af compliant, 12~60V DC (jumper setting) for non 802.3af standard Power-over-Ethernet (PoE) Standby: 200 ma @ 12V Current Operational: 280 ma @ 12V Operating Temperature 0 to 55 ºC (32 to 121 ºF) Physical Dimensions 5.42” x 3.14” x 2.28” (137.7 mm x 79.7 mm x 57.9 mm) Weight 0.9 ounces (0.3 kg) KEYSCAN INC. ä£Ê ÕÀÃÊ-ÌÀiiÌÊ >ÃÌ 7ÌLÞ]Ê"Ì>ÀÊ£ ÊÈÈ *i\Êäx°{Îä°ÇÓÓÈÊÊ/ÊÀii\Ê£°nnn°xÎ°ÇÓÓÈÊ>Ý\Êäx°{Îä°ÇÓÇx ÜÜÜ°iÞÃV>°V> Rev.:03-09 7>ÌÊÀiÊvÀ>Ì¶Ê Ì>VÌÊÞÕÀÊV>ÊÀi«ÀiÃiÌ>ÌÛiÊ>Ì\ TDS Tailgating Detection System Keyscan’s tailgating detection system (TDS) is designed for high security applications where tailgating presents a serious threat. With the provided Keyscan reader, the TDS interfaces with the Keyscan access control panels and other physical access control products. When more than one person passes through the curtain on a single card read, the TDS will trigger the built-in audible alarm as well as activate an alarm relay that can be interfaced with the access control system. When maximum security is required for secure areas such as server rooms, man traps, clean rooms and other areas, the TDS adds an unprecedented layer of security to any access control system. FEATURES • Triggers an on-board audible alarm as well as an alarm relay when more than one individual enters a secure area on a single card read • Keyscan’s door relay authorizes passage and lock control when used with the provided TDS interface relay (DPDT) • Can be wall mounted or door frame mounted • 32 IR sensors allow for directional detection and provide over 30” (76.2 cm) of vertical detection range • Kit includes: 1 Transmitter unit with internal reader mount bracket (concealed installation for door mount configuration), 1 Keyscan reader, 1 TDS interface DPDT relay (for use with access control system), 1 Receiver unit, and 2 Bypass Keys • The mounting distance between the transmitter unit and receiver unit must be 30” (76.2 cm) min. to 80” (203.2 cm) max. • For indoor use only www.keyscan.ca TDS Tailgating Detection System SPECI F I CATI ON S OUTPUT RELAYS: (Output contact rating: 1 Amp @30 Vdc / 0.5 Amp @125 Vac) CONNECTION PLANNING TABLE Mag Lock Relay Can be used to control an electric lock in response to a valid user input. Form C (held 5 sec) INPUTS (N/O Shared Gnd) Alarm Relay Connect to remote equipment to monitor alarm conditions. (Alarms Include: Tailgater, Door Prop, Loiter, and Tamper conditions) Changes state to indicate alarm. Form C (2.5 second minimum duration) Valid “A” Card Door Relay Connect to remote equipment to monitor door status. Form C (Follows Door Input) “A” & “B” Passage Complete These relays change state upon valid passage of a user from the A or B side. Form C (held 1 sec) # of wires 2 (22 AWG) Valid “B” Card 2 (22 AWG) Bypass 2 (22 AWG) Door Switch Power 12-24 Vdc @ 500mA 2 (22 AWG) Sender 2 (18 AWG) Receiver/ Control 2 (18 AWG) OUTPUTS Form C 1 Amp INPUTS: (all Inputs share 2 common GNDs on connector) Valid “A” Card Valid “B” Card Mag Lock Relay 2 (18 AWG) N/O contact from ACS that momentarily closes to indicate a valid user approaching from the “A” side.* Alarm Relay 2 (22 AWG) N/O contact from ACS that momentarily closes to indicate a valid user approaching from the “B” Side * * Enable free passage by shorting input for valid A or B Card. Door Relay 2 (22 AWG) “A” Passage Complete 2 (22 AWG) “B” Passage Complete 2 (22 AWG) Bypass N/O contact that enables bypass when closed. Resets alarm. Same function as key switch. Door Closed loop from door when door is closed. Optional, used for door prop monitoring and enhanced TDS operation. Door mount opposite from the door swing POWER REQUIREMENTS* Power 12-24 Vdc @ 500 mA DOOR MOUNT Wall mount of corridor walls ORDERING OPTIONS TDS-PROX TDS with K-PROX2 (125 kHz proximity reader) TDS-SMART TDS with K-SMART (13.56 MHz smartcard reader) TDS-SM125 TDS with K-SMART-125 (13.56 MHz smartcard and 125 kHz proximity reader) TDS-SMG TDS with K-SMART-GOV (13.56 MHz smartcard reader with government formats) TDS-SMG125 TDS with K-SMART-GOV/125 (13.56 MHz smartcard reader with government formats and 125 kHz proximity) 54.7” (138.938 cm) WALL MOUNT Door/Hallway width 30” (76.2 cm) min – 80” (203.2 cm) max OPTIONAL EQUIPMENT TDS-SPCR Optional 2” (5.08 cm) black spacer (set of 2) for mounting TDS on a cement wall or cement door frame to provide space for wiring. 2” (5.08 cm) * Refer to reader installation guide for specific power and wiring requirements 'HSWKµ FP KEYSCAN INC. 901 Burns Street East, Whitby, Ontario L1N 6A6 Keyscan Inc. reserves the right to alter designs and specifications without notice or obligation Phone: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 www.keyscan.ca Rev.:04-2010 WSSKP1 KE YS C AN WIE GAND KEY PA D • Stand alone access control or part of a complete access control system. • Suitable as replacement “reader” for any 26 bit or Keyscan 36 bit Wiegand reader. • Brushed Stainless Steel keypad for durability that matches almost any decor. • Braille keys for visually impaired requirements. • Suitable for most exterior or interior applications. • Simple to use commands allow maximum flexibility. • Fast, easy, trouble-free installation. www.keyscan.ca WSSKP1 KE YS C AN WIE GAND KEY PA D FEATURES A N D B E N E F I T S • Simple programming permits use in many different types of installations from single door (low and moderate security) to sophisticated CCTV and access control systems whether it is a retrofit application or a new installation. • Since the WSSKP1 supports industry standard 26 bit Wiegand data or proprietary KEYSCAN 36 bit format, it can be used with either a KEYSCAN ACU or with alternate control units supporting standard 26 bit data. • Three digit facility codes can easily be activated for installations using site or facility codes from 001 to 255. • Braille keypad permits use in premises that are accessible to visually impaired. • In stand alone applications, PIN’s can be set up to be either 3, 4 or 5 digits to suit the customer’s security requirements. • Any single PIN can be changed OR all PIN’s can be eliminated with simple keypad command sequences for stand alone applications. • Can be programmed to trigger a CCTV input prior to the host unlocking the controlled entry point. • As many as 28 distinct PIN codes can be programmed into the WSSKP1 for stand alone operation. A PPL I CATI O N S • As a standalone unit to control access at a single entry point whether it be a standard electric lock requiring sustained power for a predetermined time or momentary activation for parking gates. • As part of an integrated access control system to pass user PIN’s in Wiegand format to a host for verification and authorization. • As part of an integrated CCTV and access control system to trigger a camera while passing user PIN to the host system for verification and authorization. • As a replacement keypad reader in retrofit installations using industry standard 26 bit Wiegand encoded data. S PECI F I CATI O N S System Requirements: External power supply: Input power (min): 12 VDC ± 5% (30 mA) Output (max): 12 VDC @ 500 mA into a non-inductive or diode suppressed inductive load Maximum power: 530 mA Mechanical Tolerances: Key travel: 0.050" Key pressure: Light touch, audio feed back, positive action keypad requiring only 4 lbs. pressure. Dimensions: 3" x 4.5" x 0.5" (76mm x 114mm x 13mm) Environmental Tolerances: Suitable for light to moderate residential, commercial and industrial applications. Relative Humidity: 5% to 95% Non-Condensing* Temperature: -35° to 65° C Button life expectancy is greater than 1,000,000 activations. Certifications: FCC Part 15, subsection J for a class B device, UL, CSA, CE KEYSCAN INC. 901 Burns Street East Whitby, Ontario L1N 6A6 Phone: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 www.keyscan.ca Want more information? Contact your local representative at: HID iCLASS Future proof your business today with Keyscan iCLASS readers & cards. With iClass you can add biometrics, data storage and retrieval, PC Log ON and other on-card applications. Move to the increased functionality and security of read/write contactless smart cards that can deliver a new set of benefits - ease, affordability, and confidence. That's because Keyscan's iCLASS can be seamlessly added to your current system. And you can upgrade with a minimum of hassle and expense! Keyscan's iCLASS offers: • Plug-n-play compatibility with existing Keyscan access control systems. • Flexibility - meets multiple ISO standards (15693 or 14443A/B). • 2k bits and 16k bits credentials (card, key, or tag) with Keyscan's 36 Bit format for access control. • High security with mutual authentication, encrypted data transfers and 64 bit diversified key • The convenience of proximity in a smart package. www.keyscan.ca HID iCLASS ALL iCLASS READERS/WRITERS FEATURE: • A multi-technology 13.56 MHz interface that meets ISO 14443A (MIFARE®), 14443B2, and 15693 standards. • The ability to read 32 bit MIFARE serial numbers. • Highly secure 64 bit diversified keys for mutual authentication. • Encrypted data transfer between the card and the reader through the use of secure algorithms. • Advanced key management systems to reduce the risk of compromised data or duplicated cards. Dimensions: • R10 Reader (KeyR10) 1.90" x 4.04" x .80" (4.83cm x 10.26 cm x2.03cm) • R40 Reader and RW400 Reader/Writer (KEYR40) and (KEYRW400) 3.30" x 4.80" x .85" (8.38cm x 12.19cm x 2.16cm) • RK40 Reader with Keypad (KEYRK40) 3.30" x 4.80" x .90" (8.38cm x 12.19cm x 2.286cm) Read Range: • R10: 2 – 3" (5.0 cm-7.6 cm) when using KEY2K2 or KEY16K2 cards • R40/RW400: 2.5"-4.5" (6.3 cm-11.4 cm) when using KEY2K2 or KEY16K2 cards • RK40: 3.0"-4.0" (7.6 cm-10.1 cm) when using KEY2K2 or KEY16K2 cards (Note: Read Range reduced by 50% when using iCLASS Key Fobs and Tags) • A Wiegand output that easily interfaces with existing Keyscan access control panels. Input Voltage: • An easy-to-install, three-part reader, compatible with global electrical back boxes, and made more secure with the addition of a tamper magnet* and security screw. Operating Temperature: • 12 VDC at Reader • -30° to 150°F (-35° to 65°C ) • A factory or field configurable tri-color light bar and multi-tone speaker that provides distinguishable indicators for both the visually and hearing impaired. Operating Humidity: • Confidently install iCLASS contactless smart card readers, knowing that the Wiegand output easily interfaces with existing Keyscan access control panels. • 36 Bit Keyscan * Tamper magnet is built into all models except the R10. • 5-95% non-condensing Output Formats: Approvals: • UL, FCC, CE, VdS*, Canada, New Zealand, Singapore, Japan and Korea Warranty: Lifetime iCLASS Card iCLASS Key Fob iCLASS Key Tag STANDARD CONTACTLESS SMART CARD CONTACTLESS SMART FOB CONTACTLESS SMART TAG Memory Size available: 2k bits (256Bytes) and 16k bits (2kBytes) Memory Size available: 2k bits (256Bytes) and 16k bits (2kBytes) Memory Size available: 2k bits (256Bytes) and 16k bits (2kBytes) iClass Cards KEY 2K2C (iClass Clamshell card 2K, 2 applications) iClass Key Fob KEYFOB2K2 (iClass Key Fob 2K, 2 applications) iClass Adhesive Tag KEYTG2K2 (iClass adhesive tag 2K, 2 applications) Format: Keyscan 36bit Format: Keyscan 36bit Operating Temperature: - 40° to 158°F (-40° to 70°C) Operating Temperature: - 40° to 158°F (-40° to 70°C) Packaging: 50 Sequential fobs per package Packaging: 50 Sequential tags per package KEY 2K2 (iClass card 2K, 2 applications) KEY 2K2MAG (iClass card 2k, 2 applications with magnetic swipe) KEY 16K16 (iClass card 16K, 16 applications) Format: Keyscan 36bit Slot Punch: Vertical Only Operating Temperature: - 40° to 158°F (-40° to 70°C) Packaging: 50 Sequential cards per package KEYSCAN INC. 901 Burns Street East Whitby, Ontario Canada L1N 6A6 Tel: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 Web: www.keyscan.ca Want more information? Contact your local representative at: HID Proximity The word that best summarizes the Keyscan HID proximity readers & cards is "convenience". • Convenience for an employee who can use the same HID card to open the gate of a secured parking lot, enter the building, clock in for payroll and attendance, document the checkout of tools and equipment, enable controls for restricted machinery. • Convenience for building management who need maintenance free equipment. • Convenience for security personnel who need to know that the people they protect are safe. Proximity Products - Proximity provides the highest level of convenience and ease-of-use available in access control technology, and is now the most utilized technology in new access control installations. Proximity cards and key-fobs need only be placed within proximity of their readers to activate the system. The technology is cost-effective and it is unaffected by dirty environments, weather conditions or strong magnetic fields. Because not everyone needs smart cards. Keyscan's 36 Bit HID proximity readers and cards will continue to be the industry-leading solution. With a variety of readers and cards it is easier to upgrade to proximity and provides an alternate form of credential. Your investment in proximity is safe with Keyscan & HID! Keyscan HID Proximity readers & cards offer: • Off the shelf ordering of cards and readers. • No need to remember your last sequence of cards. • No custom orders or delayed deliveries. Make sure you ask for Keyscan 36 Bit HID readers and cards. www.keyscan.ca HID Proximity READER SPECIFICATIONS: Size: • HID Prox Point+ (HID-6005B) 3.135" x 1.70" x 0.66" ( 7.96 x 4.3 x 1.68 cm) • HID Miniprox (HID-5365) 6.0" x 1.7" x 1.0" ( 15.2 x 4.3 x 1.91 cm) • HID Thinline II (HID-5395) 4.7" x 3.0" x 0.68" ( 11.9 x 7.6 x 1.7 cm) • HID Proxpro (HID-5355) 5.0" x 5" x 1" (12.7 x 12.7 x 2.54 cm) • HID Proxpro with Keypad (HID-5355KP) 5.0" x 5" x 1" (12.7 x 12.7 x 2.54 cm) • HID Maxi Prox (HID-5375) 12" x 12" x 1" (30.5 x 30.5 x2.54 cm) Typical Current Draw: • HID Prox Point+: 20mA avg 75mA peak at 12VDC • HID Miniprox: 20mA avg 110mA peak at 12VDC • HID Thinline II: 20mA avg 115mA peak at 12VDC • HID Proxpro: 100mA avg 120mA peak at 12VDC • HID Proxpro with Keypad: 100mA avg 120mA peak at 12VDC • HID Maxiprox: 200mA avg 700 mA peak at 24VDC Operating Temperature: -22° to 150°F (-30° to 65°C) Read Range: Operating Humidity: 0 to 95% relative humidity non-condensing • • • • • • Cable Distance: Wiegand Interface: 500 feet (152 m) HID Prox Point+: 1-2" read range using HID-C1325 cards HID Miniprox: 4-5" read range using HID-C1325 cards HID Thinline II: 4-5" read range using HID-C1325 cards HID Proxpro: 5-8" read range using HID-C1325 cards HID Proxpro with Keypad: 5-8" read range using HID-C1325 cards HID Maxiprox: 16-24" read range using HID-C1325 cards Input Voltage: • • • • • • HID HID HID HID HID HID Prox Point+: 12VDC at reader Miniprox: 12VDC at reader Thinline II: 12VDC at reader Proxpro: 12VDC at reader Proxpro with Keypad: 12VDC at reader Maxiprox: 24VDC at reader Indoor/Outdoor Design: Sealed in a rugged, weatherized polycarbonate enclosure designed to withstand harsh environments, providing reliable performance and a high degree of vandal resistance. Easily installed in any location, even with the optional keypad. Certifications: Canada/UL 294 Listed: Access Control System Units FCC Certification, United States, Canada CE Mark, Fifteen EU Countries under the R&TTE Directive Warranty: Warranted against defects in materials and workmanship for life from date of shipment. HID-C1325 HID-T1345 STANDARD PROXIMITY CARD PROXIMITY KEY TAG Size: 3.385" x 2.135" x 0.075" Size: 1.9 x .900 x 0.16" (4.3 x 2.29 x 0.41cm) Typical Maximum Read Range: • HID6005B: 2 - 3" (5.1-7.6cm) • HID-5365: 4 - 5.5" (10.2-14.0cm) • HID-5395: 4 - 5.5 (10.2 – 14.0cm) • HID-5355 and HID-5355KP: 6 - 9" (14-20.3cm) • HID-5375: 16 – 29" (40.6-73.7cm) Typical Maximum Read Range: • HID6005B: 1 – 1.5" (2.5 – 3.8 cm) • HID-5365: 1 - 2" (2.5 -5.1 cm) • HID-5395: 1 – 2" (2.5 – 5.1 cm) • HID-5355 and HID-5355KP: 1 - 4" (2.5 – 10.2cm) • HID-5375: 4 - 15" (10.2 - 38cm) Operating Temperature: -50° to 160°F (-45° to 70°C) Operating Temperature: -50° to 160°F (-45° to 70°C) Packaging: 50 sequential units per package Packaging: 50 sequential units per package Warranty: Lifetime Warranty: Lifetime HID-C1386 HID-1391 PHOTO IMAGING PROXIMITY CARD MICRO PROXIMITY ADHESIVE TAG Size: 3.37 x 2.125 x 0.030" (8.6 x 5.4 x 0.076 cm) Size: 1.285" (32.639mm) Diameter Typical Maximum Read Range: • HID6005B: 1 – 1.5" (2.5 – 3.8 cm) • HID-5365: 1 - 2" (2.5 -5.1 cm) • HID-5395: 1 – 2" (2.5 – 5.1 cm) • HID-5355 and HID-5355KP: 1 - 4" (2.5 – 10.2cm) • HID-5375: 4 - 15" (10.2 - 38cm) Typical Maximum Read Range: • HID-6005B: 0.5"-2.0" (1.2 – 5.1cm) • HID-5365: 0.5" – 2.5" (1.2 – 6.4cm) • HID-5395: 1.0"- 3.0" (2.5 – 7.6cm) • HID-5355 and HID-5355KP: 1.0" – 4.0" (2.5 – 11.4cm) • HID-5375: 4.0" – 15.0" (10.2 – 38cm) Operating Temperature: -50° to 160°F (-45° to 70°C) Operating Temperature: -50° to 160°F (-45° to 70°C) Packaging: 50 sequential units per package Packaging: 50 sequential units per package Warranty: Lifetime Warranty: Lifetime KEYSCAN INC. 901 Burns Street East Whitby, Ontario Canada L1N 6A6 Tel: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 Web: www.keyscan.ca Want more information? Contact your local representative at: INDALA • Keyscan's Indala offers choices for dependable 125 kHz proximity access control readers. Simply select one of the PX series proximity readers that support your desired read range: 5-inch/12.7cm, 12-inch /30.5cm or 28-inch / 71.1cm. • Keyscan Indala readers offer the additional benefit of enhanced security between the reader and card. • Keyscan's Indala family of interchangeable FlexPass cards and tags are designed to withstand the tough rigors of the access environment. • All readers, cards and tags are pre-configured for Keyscan 36 Bit wiegand output, offering off the shelf ordering. No need to remember your last card numbering sequence. • Indala readers are durable and weather resistant. • Lifetime warranty on cards and readers. www.keyscan.ca INDALA S PECI F I CATI O N S Size: Operating Temperature: • Slim (PX-603): 4.5"H x 1.7" W x 0.8"T (11.4cm x 4.3cm x 2.0cm) • Wall switch (PX-605): 4.5"H x 3.0"W x 0.8"T (11.4cm x 7.6cm x 2.0cm) • Mid-Range (PX-610): 5.1"H x 6.1"W x 1.1"T (13.0cm x 15.5cm x 2.8cm) • Long-Range (PX-620): 11.2"H x 11.2"W x 1.8"T (28.4cm x 28.4cm x 4.6cm) • -31° to +149°F (-35° to +65°C) Read Range: Input Voltage: Audio Tone: • • • • • • • • • Standard, independently controllable Slim: Up to 5" (12.7cm) using PX-C1 Wallswitch: Up to 5" (12.7cm) using PX-C1 Mid-range: Up to 12" (30.5cm) using PX-C1 Long-Range: Up to 28" (71.1cm) using PX-C1 LED Indicator: • Tri-color standard (red, green, amber) Slim: 12 VDC at reader Wallswitch: 12 VDC at reader Mid-range: 12 VDC at reader Long-Range: 24 VDC at reader Output Formats: • 36 bit Keyscan. 26 bit option available (special order) TYPICAL CURRENT DRAW: Frequency: Off Metal: • 125 kHz (excitation) • • • • Approvals: Slim: 65 mA @ 12V Wallswitch: 65 mA @ 12V Mid-Range: 117 mA @ 12V Long-Range: 1.0A @ 24 VDC • UL 294/cUL, FCC Certification – United States, Canada Certification, CE Mark – Europe, Australia C-Tick, New Zealand/EMC On Metal: • • • • WARRANTY: Slim: 86 mA @ 12V Wallswitch: 86 mA @ 12V Mid-Range: 111 mA @ 12V Long-Range: 1.2 A @ 24 VDC Indala warrants this product against defects in material and workmanship under normal use and service. The warranty period commences with the date of shipment. See complete warranty statement for further details. Read range stated when readers installed according to instructions. Read range Maximum: • • • • may vary when mounted on metal and with different cover designs. Illumination Slim: 96 mA @ 12V Wallswitch: 96 mA @ 12V Mid-range: 140 mA @ 12V Long-Range: 1.2 A @ 24 VDC PX-C1 STANDARD PROXIMITY CARD colors may differ based on cover design color. Specifications are subject to change without notice. Indala reserves the right to discontinue any product without notice. PX KEY PROXIMITY KEY PAD PX-ISO30 PHOTO IMAGING PROXIMITY CARD Size: Size: Size: • 3.38"h x 2.13"w x 0.065"t • 1.725"h x 1.197"w x .215"t (43.8mm x 30.4mm x 5.46mm) • 3.38"h x 2.12"w x 0.03"t (86mm x 54mm x 0.76mm) nominal thickness may vary by +/-0.003" (0.08mm) Typical Maximum Read Range Read Range: • Slim/Wallswitch PX 603: 2 inches (5.08 cm) • Mid-Range PX 605 + 610: 7 inches (17.78cm) • Long Range PX 602: 15 inches (38.1cm) • Slim/Wallswitch- PX-603: Up to 5" (12.7cm) • Mid-Range- PX-605 + 610: Up to 12" (30.5cm) • Long-Range- PX-620: Up to 22" (55.9cm) Read Range: • Slim PX-603: Up to 5" (12.7cm) • Wallswitch PX-605: Up to 5" (12.7cm) • Mid-Range PX-610: Up to 12" (30.5cm) • Long-Range PX-620: Up to 28" (71.1cm) Temperature: Temperature: • -22°F to +149°F (-30°C to +65°C) • -22°F to +149°F (-30°C to +65°C) Construction: Packaging: • Outer Shell: Ultrasonic welded polycarbonate • Inner Shell: RF core shielded in epoxy • 50 Sequential units per package. Packaging: • 50 Sequential units per package. Temperature: • Operating: 32°F to +122°F (0°C to +50°C) • Non-operating: -20°F to +122°F (-30°C to +50°C) Material: PVC Finish Front: White glossy front standard Finish Back: White glossy back with slot-punch indicators and small Motorola logo standard. Coding: Wiegand, ABA Track II Magnetic Stripe and others available, exact coding standard, with no gaps or over-runs. Packaging: • 50 Sequential units per package. KEYSCAN INC. 901 Burns Street East Whitby, Ontario Canada L1N 6A6 Tel: 905.430.7226 Toll Free: 1.888.539.7226 Fax: 905.430.7275 Web: www.keyscan.ca Want more information? Contact your local representative at:

Keyscan Proximity Reader/keypad

Rating

Date

Size

Views

Categories

Share

Transcript