Transcript
KING CANADA 11” ELECTRIC GRASS TRIMMER
MODEL: 8511GT
INSTRUCTION MANUAL COPYRIGHT © 2010 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
WARRANTY INFORMATION
2-YEAR LIMITED WARRANTY ELECTRIC GRASS TRIMMER
KING CANADA TOOLS OFFERS A 2-YEAR LIMITED WARRANTY FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centers across Canada.
LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products. To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.
NOTE TO USER This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.
PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
GENERAL & SPECIFIC SAFETY INSTRUCTIONS FOR ELECTRIC GRASS TRIMMERS 1. KNOW YOUR TOOL Read and understand the owners manual and labels affixed to the tool. Learn its application and limitations as well as its specific potential hazards.
2. KEEP GUARDS IN PLACE. Keep in good working order, properly adjusted and aligned.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. Make sure the floor is clean and not slippery due to wax and sawdust build-up.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lit and provide adequate surrounding work space.
5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area.
6. MAKE WORKSHOP CHILD-PROOF. -with padlocks, master switches or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE PROPER EXTENSION CORD Make sure the extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. See electrical information page for table showing correct size to use depending on the cord lenght and the nameplate amperage rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
9. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows.
10. ALWAYS WEAR SAFETY GLASSES. Also use a face or dust mask if cutting operation is dusty. Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only have impact resistant lenses, thet are NOT safety glasses.
11. DON’T OVERREACH. Keep proper footing and balance at all times.
12. MAINTAIN TOOL WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
13. DISCONNECT TOOLS. Before servicing, when changing accessories or attachments.
14. AVOID ACCIDENTAL STARTING. Make sure the swich is in the ‘’OFF’’ position before plugging in.
15. USE RECOMMENDED ACCESSORIES. Consult the manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper accessories may cause risk of injury to persons.
16. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other parts that are damaged should be carefully checked to ensure that they will operate properly and perform their intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other parts that are damaged should be properly repaired or replaced.
17. NEVER LEAVE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don’t leave any tool running until it comes to a complete stop.
SPECIFIC SAFETY RULES Warning! When using electric grass trimmers, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. 1. Make sure your extension cord is in good condition. When using an extention cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 50’ (15m) or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. 2. Before operating, check the tool’s cord and the extension cord for signs of damage or aging. If either cord becomes damaged during use, disconnect it from the power supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING. Do not use the grass trimmer if the cord is damaged or worn. 3. Read the instructions carefully. Be familiar with the controls and proper use of the grass trimmer. 4. When not in use, grass trimmer should be stored indoors in a dry, secure location out of the reach of children. 5. Maintain tool with care. Keep fan area clean for best and safest performance. Follow instructions for proper maintenance. 6. Keep extension cord away from cutting line.
7. Check air vents. Keep air vents free of debris which can restrict air flow and cause damage to the grass trimmer. 8. Do not unplug by pulling on extension cord. To unplug, grasp the plug, not the extension cord. 9. To reduce risk of electric shock, do not expose to rain, do not use on wet surfaces. Store indoors. 10. Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free of debris. Clean after each use. See Maintenance instructions. 11. Avoid using the grass trimmer, while people, especially children or pets, are nearby. 12. Only use the grass trimmer in daylight or in good artificial light. 13. Never operate the grass trimmer with a damaged guard or without the guard installed. 14. Only switch on the motor when your hands and feet are away from the cutting line. 15. Never attempt to install a metal cutting line in this grass trimmer. 16. Inspect and maintain the grass trimmer regularly. Only have the grass trimmer repaired by an authorized technician. 17. After manually extending new cutting line, always return the grass trimmer to its normal operating position before switching on.
GETTING TO KNOW YOUR ELECTRIC GRASS TRIMMER
1. 2. 3. 4. 5. 6.
On/Off switch. Press switch to turn motor On/Off. Control handle. Power cord (polarized). Safety guard. Protects you and others from the cutting line. Cutting line. Comes with a single spool & line (32 ft. x 0.065”) Extension cord lock system. Prevents the extension cord from being unplugged during use. MODEL Cutting width Line thickness Spool & line No load speed Motor Voltage Dimensions (LxWxH) Weight
7. Extension cord (for illustration purposes only- extension cord not included) 8. Spool & line cover. 9. Spool & line. 10. Manual line-feed button. Push this button to manually extend the length of the cutting line.
8511GT 11” 0.065” Single 32ft. x 0.065” 11,100 RPM 3.5 Amp. 110V, 1 phase, 60 Hz 13” x 9” x 33” 3.8 lbs
ELECTRICAL INFORMATION
WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THIS POWER TOOL DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY WARNING: YOUR ELECTRIC GRASS TRIMMER IS WIRED AT THE FACTORY FOR 110-120V OPERATION, IT MUST BE CONNECTED TO A 110-120V/15-AMP. TIME DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE. The grass trimmer plug (A) Fig.1 is intended for use with a polarized 2 wire or 3 wire outdoor rated extension cord (B) as illustrated in Fig.1.
A
B
SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUG To reduce the risk of electric shock, this grass trimmer comes with a polarized 120V plug (one blade is wider than the other). It must be used with a suitable polarized 2 wire or 3 wire extension cord. Polarized connections will fit together only one way. Make sure that the receptacle end of the extension cord has large and small blade slot widths. If the plug does not fit fully into the extension cord, reverse the plug. If it still does not fit, obtain a suitable extension cord. If the extension cord does not fit fully in the outlet, contact a qualified electrician to install the proper outlet. Do not modify the tool plug or extension cord in any way. USE PROPER EXTENSION CORD Make sure the extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. See Fig.2 for table showing correct size to use depending on the cord lenght and the nameplate amperage rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Always use U.L. or CSA listed extension cords rated for outdoor use. WARNING: Replace damaged cords immediately. Use of damaged cords can shock, burn or electrocute.
FIGURE 1
Tool’s Amperage Rating
Cord Size in A.W.G. Cord Length in Feet 25 50 100 150 18 18 18 18 14
3-6 6-8 8-10 10-12 12-16
FIGURE 2
CONNECTING EXTENSION CORD TO GRASS TRIMMER PLUG Secure the extension cord (A) Fig.3 to the extension cord lock (B) on the motor housing. First bend the end of the extension cord and pass it around the notch of the cord lock, then pull on the extension cord to get a tight fit. This will prevent accidental unplugging of the extension cord during use. Then plug the female end of the extension cord (C) into the tool’s polarized plug (D). WARNING! To reduce risk of electric shock, do not expose to rain, do not use on wet surfaces. Store indoors.
FIGURE 3
16 16 16 16 12
16 14 14 14 -
14 12 12 12 -
ASSEMBLY & OPERATION
ASSEMBLING YOUR GRASS TRIMMER Assembling Switch and Motor Housings CAUTION! Make sure that the excess wire between the switch housing and the motor housing is not twisted during the assembly. Failure to do so may result in damage to the wires and/or the grass trimmer as well as serious injury to the operator causes by electrocution. Align the grooves on the motor housing (A) Fig.4 with the grooves on the switch housing (B). Push these two housings together until they click into position.
FIGURE 4
Assembling Safety Guard Align the locking tabs of the safety guard (A) Fig.5 with the locking tabs of motor housing (B). Once the safety guard is aligned, push it up completely against the motor housing and turn it clockwise to lock it into place. WARNING! Never operate this grass trimmer without the safety guard installed.
FIGURE 5
OPERATING YOUR GRASS TRIMMER Refer to the general and specific safety instructions and familiarize yourself with your grass trimmer before attempting to operate. This grass trimmer is intended for cutting dry grass only. Starting/Stopping Grass Trimmer 1) Connect an outdoor use extension cord to the tool’s polarized plug. Follow the instructions for locking extension cord to cord lock, refer to Fig.3. 2) To start the grass trimmer, squeeze the On/Off switch (A) Fig.6. 3) To stop the grass trimmer, release the On/Off switch (A).
FIGURE 6
Operational guidelines 1) Hold the grass trimmer with both hands only a few inches above the ground and squeeze the switch to start. In a sweeping motion, move the grass trimmer side-toside, advancing slowly, as shown in Fig.7. 2) If the grass trimmer starts running slowly, reduce the load. 3) Once you have finished using the grass trimmer, make sure it is cleaned before storing indoors, see maintenance section for more information.
FIGURE 7
OPERATION & MAINTENANCE
OPERATING YOUR GRASS TRIMMER Line-Feed (Automatic and Manual Mechanisms) During use, the tip of the cutting line will get shorter due to wear, especially if the cutting is done along sidewalks or other abrasive surfaces or thick weeds are being cut. Line feeding can be done automatically or manually. Automatic Line-feed- When the grass trimmer switch is released after use, the cutting line will lengthen by increments. Once the cutting line reaches the line cutting blade (A) Fig.8, the cutting line will be cut to the perfect length for operation. Manual Line-feed- To manually increase the length of the cutting line, first unplug the extension cord from the power source. Position the grass trimmer upside down or on its side and press the manual line-feed button (B) Fig.8 as many times as necessary to lengthen the cutting line. Installing a New Spool & Line Warning! Only use identical replacement 0.065” pre-wound spool & line (King mod. KW-134). 1) Unplug the extension cord from the power source. 2) Depress the spool cover tabs (A) Fig.9, lift and remove the spool cover (B) from the housing. 3) Remove the empty spool (C) from the housing by simply pulling it out. Remove any dirt and grass from the spool cover and housing. 4) Purchase a new pre-wound spool & line (32ft. x 0.065”). It is available as a replacement accessory, King model KW-134. Place the new spool into the housing and guide the cutting line (D) through the eyelet (E). The cutting line should protrude 3-3/4” from the eyelet. 5) Align the tabs on the spool cover with the cut outs in the housing. Push the spool cover onto the housing until it snaps securely into place. MAINTENENCE
FIGURE 8
FIGURE 9
WARNING: For your own safety, release switch to stop grass trimmer and remove extension cord plug from power source outlet before you attempt any maintanance or repairs. WARNING: All repairs, electrical or mechanical, should be attempted only by trained repairmen. Contact the nearest King Canada Service Center. Use only identical replacement parts, any other may create a hazard. If the power cord is worn or damaged in any way, have it replaced immediately. CLEANING AND STORAGE- TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.) Use only mild soap and a damp cloth to clean the tool. Your grass trimmer should be stored indoors in a dry place. WARNING: Certain cleaning agents and solvents can damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents which contain ammonia. Avoiding use of these and other types of cleaning agents will minimize the possibility of damage. CAUTION: DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. Troubleshooting If your grass trimmer does not seem to operate properly, follow the troubleshooting guidelines below. If this does not solve the problems, please contact the nearest King Canada Service Center. Tool runs slowly a) Check that the spool housing can rotate freely. Carefully clean it if necessary. b) Check that the cutting line does not protrude more than 3-3/4” from the spool housing. If it does, cut it off so that it just reaches the line trimming blade. Automatic line-feed does not work a) Keep the tabs depressed and remove the spool cover from the housing. b) Pull the cutting line until it protrudes 3-3/4” from the housing. If insufficient cutting line is left on the spool, install a new spool & line. If the line-feed still does not work or the spool is jammed, try the following suggestion: • Carefully clean the spool cover and housing. • Remove the spool and check if the manual line-feed button can move freely. • Remove the spool and unwind the cutting line, then wind it on neatly again. Replace the spool as instructed.
