Transcript
R
1-800-669-9690
O
A
D
M
A
S
T
E
R
MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc.
6110 NE 127th Ave.
Vancouver, WA 98682
PARTS LIST: 1- MAIN BRACE (A) - Passenger side 1- MAIN BRACE (B) - Driver's side
1-800-669-9690
fax 360-735-9300
www.roadmasterinc.com
KIT NO. 1123-1
7-5-00 IMPORTANT: All All brackets brackets must must be be assembled assembled with with all all the the bolts bolts left left loose loose for for final final adjustment adjustment and and positioning positioning (before (before tightening) tightening) IMPORTANT: unless otherwise instructed. All bolts must be torqued for proper strength. If more than one bolt is used per fastening point, unless otherwise instructed. All bolts must be torqued for proper strength. If more than one bolt is used per fastening point, the diagram may only show one. the diagram may only show one. Use flat flat washers washers over over all all slotted slotted holes holes •• Use Use lock lock washers washers on on all all fasteners fasteners •• Use ROADMASTER Limited Limited Warranty, Warranty, including including One-Year One-Year Conditional Conditional Warranty Warranty Text Text and and Product Product Registration Registration Card, Card, in in Carton. Carton. ROADMASTER
WARNING
Failure to to follow follow these these instructions instructions Failure can result result in in property property damage, damage, perpercan sonal injury injury or or even even death. death. sonal
• Installation of most mounting brackets requires moderate mechanical •• Installation of most brackets requires moderate mechanical Installation ofskills. most mounting mounting brackets requires moderate mechanical aptitude and We strongly recommend professional installation by aptitude and We aptitude and skills. skills. We strongly strongly recommend recommend professional professional installation installation by by an experienced installer. an experienced installer. installer. • an Theexperienced installer must read the instructions and use all bolts and parts •• The must the use and parts The installer installer must read the instructions instructions and use all bolts bolts andthread parts supplied. When theread instructions require theand reuse of all factory bolts, supplied. Failure to fasten could in of supplied. Failure to securely securely fasten the bracket could result result in loss loss fasten of the the lock and/or lock washers must alsothe be bracket used. Failure to securely towed vehicle. towed vehicle. the bracket could result in loss of the towed vehicle. •• Do Do not not use use this this document document for for custom custom fabrication, fabrication, as as itit may may not not show show all all parts parts or or structural structural components. components. Custom Custom fabrication fabrication or or an an attempt attempt to to copy copy this this bracket bracket design design could could result result in in loss loss of of the the towed towed vehicle. vehicle. •• The owner inspect all mounts and brackets before each use Every 3,000must miles, the owner must inspect the fasteners for proper for cracks or othertosigns of fatigue. Also, inspect chart the fasteners for page proper torque, according the bolt torque requirements on the last of torque, according to the bolt torque requirements on the page. these instructions. The owner must also inspect allchart mounts andlast brackets Failure to doorso could resultofinfatigue loss ofevery the towed for cracks other signs 3,000vehicle. miles. Failure to do so couldowner resultmust in loss of the towed vehicle. • The check the vehicle manufacturer's instructions for the procedure(s) to the prepare themanufacturer's vehicle for towing. Some vehicles • proper The owner must check vehicle instructions for the must be procedure(s) equipped with to a transmission pump, axle disconnect, drivproper prepare the lube vehicle foran towing. Some vehicles eline free-wheeling hubslube before they towed. Failure must disconnect be equippedorwith a transmission pump, ancan axlebedisconnect, drivto properly equipor the vehicle will cause severethey damage to towed. the transmiseline disconnect free-wheeling hubs before can be Failure sion. to properly equip the vehicle will cause severe damage to the transmis• Ifsion. running changes were made by the vehicle manufacturer after this waschanges designed,were somemade bolts or fasteners in the included • bracket If running byother the vehicle manufacturer afterhardthis ware pack may no longer be the correct size. It is theininstaller’s responbracket was designed, some bolts or other fasteners the included hardsibility to verify that the bracket is securely to the vehicle, and ware pack may no longer be the correct size. fastened It is the installer’s responfitted with correct hardware, these changes. Failureand to sibility to the verify that the brackettois account securelyfor fastened to the vehicle,
fitted with the correct hardware, to account for these changes. Failure to securely securely fasten fasten the the bracket bracket could could result result in in loss loss of of the the towed towed vehicle. vehicle. •• IfIf the the towed towed vehicle vehicle has has been been in in an an accident, accident, itit must must be be properly properly repaired repaired before before attaching attaching the the bracket. bracket. Do Do not not install install the the bracket bracket ifif any any structural structural frame frame damage damage is is found. found. Failure Failure to to repair repair the the damage damage could could result result in in the the loss loss of of the the towed towed vehicle. vehicle. •• Some Some motorhome motorhome chassis chassis have have such such aa tight tight turning turning radius radius that that you you can can damage damage your your motorhome, motorhome, towed towed vehicle, vehicle, tow tow bar bar or or bracket bracket while while turning turning sharply. sharply. Before Before getting getting on on the the road, road, test test your your turning turning radius radius in in an an empty empty parking parking lot. lot. Turning Turning too too sharply sharply could could result result in in non-warranty non-warranty damage damage to to towing towing system, system, motorhome motorhome and/or and/or towed towed vehicle. vehicle. •• Do Do not not back back up up with with the the towed towed vehicle vehicle attached attached or or non-warranty non-warranty damdamage age will will occur occur to to your your towing towing system, system, motorhome motorhome and/or and/or towed towed vehicle. vehicle. •• The The safety safety cables cables must must connect connect the the towing towing vehicle vehicle to to the the towed towed vevehicle hicle frame frame to to frame, frame, with with the the cables cables crossed, crossed, with with enough enough slack slack for for sharp sharp turns. turns. Refer Refer to to the the cable cable instructions instructions for for proper proper routing. routing. Failure Failure to to leave leave enough enough slack slack in in the the safety safety cables, cables, or or failure failure to to connect connect the the safety safety cables cables frame frame to to frame, frame, will will result result in in the the loss loss of of the the towed towed vehicle. vehicle. •• This This bracket bracket is is designed designed for for use use with with ROADMASTER ROADMASTER tow tow bars bars and and ROADROADMASTER MASTER adaptors adaptors only. only. Using Using this this bracket bracket with with other other brands, brands, without without an an approved approved ROADMASTER ROADMASTER adaptor, adaptor, may may result result in in non-warranty non-warranty damage damage or or injury. injury. •• Upon Upon final final installation, installation, the the installer installer must must inspect inspect the the bracket bracket to to ensure ensure adequate adequate clearance, clearance, particularly particularly around around hoses, hoses, air air conditioner conditioner lines, lines, radiators, radiators, etc., etc., or or non-warranty non-warranty damage damage to to the the towed towed vehicle vehicle will will result. result. •• This This bracket bracket is is only only warranteed warranteed for for the the original original installation. installation. Installing Installing aa used used bracket bracket on on another another vehicle vehicle is is not not recommended recommended and and will will void void the the warranty. warranty.
R
1-800-669-9690
O
A
D
M
A
S
T
E
R
MOUNTING BRACKET KIT INSTALLATION INSTRUCTIONS ROADMASTER, Inc.
6110 NE 127th Ave.
Vancouver, WA 98682
1-800-669-9690
fax 360-735-9300
www.roadmasterinc.com
KIT NO. 1123-1 Congratulations!
You have just purchased another fine Roadmaster product. Thank you.
1. Important: please use all supplied bolts and parts and read all instructions carefully before beginning this installation. The majority of questions you may have can be answered within the text, and proper installation will ensure safe and secure travel. Now, begin the installation. Remove the tow hook from the passenger side and the tie down from the driver's side. Save the tie down. 2. Hold the passenger side main brace to the frame with the front (with 2 slots) pointing outward from the center. Bolt this brace to the bottom of the frame using the three 12mm x 1.25 x 35mm bolts and 12mm hardware provided. 3. On the driver's side, bolt the main brace to the frame by sandwiching the brace between the frame and the tie down. Then, finish off with 12mm x 1.25 x 35mm bolts lock washers and fender washers in the remaining hole. Tighten all bolts according to the torque chart below. 4. Install the tow bar according to the instructions provided with the tow bar.
HARDWARE LIST: 6-12mm x 1.25 x 35mm bolts 6-12mm lock washers 6-12mm fender washers
Failure to follow these instructions can result in property damage, personal injury or even death.
7-5-00
BOLT TORQUE REQUIREMENTS Note: The torque values represented below are intended as general guidelines. Torque requirements for specific applications may vary. Roadmaster does not warrant this information to be accurate for all applications and disclaims all liability for any claims or damages which may result from its use.
STANDARD BOLTS Thread Size
Grade
METRIC BOLTS Torque
5/16 ................... 5 ......................... 13 3/8 ...................... 5 ......................... 23 7/16 ................... 5 ........................ 37 1/2 ...................... 5 ........................ 56 5/8 ...................... 5 ...................... 150
ft./lb. ft./lb. ft./lb. ft./lb. ft./lb.
Thread Size
Grade
8mm-1.0 ......... 8mm-1.25 ....... 10mm-1.25 ..... 10mm-1.5 .......
8.8 8.8 8.8 8.8
METRIC BOLTS
Plated / Unplated
...... 20 ft./lb. ...... 19 ft./lb. ..... 38 ft./lb. ..... 37 ft./lb.
18 18 36 35
ft./lb. ft./lb. ft./lb. ft./lb.
Thread Size
Grade
12mm-1.25 ..... 12mm-1.5 ....... 12mm-1.75 ..... 14mm-2.0 .......
8.8 8.8 8.8 8.8
Plated / Unplated
...... 70 ft./lb. ...... 66 ft./lb. ..... 65 ft./lb. ... 104 ft./lb.
65 61 60 97
ft./lb. ft./lb. ft./lb. ft./lb.
All illustrations and specifications contained herein are based on the latest information available at the time of publication approval. ROADMASTER, INC. reserves the right to make changes at any time without notice in material, specification and models or to discontinue models.
